[ Upstream commit af0cb3fa3f ]
Xiumei and Christoph reported the following lockdep splat, complaining of
the qdisc root lock being taken twice:
============================================
WARNING: possible recursive locking detected
6.7.0-rc3+ #598 Not tainted
--------------------------------------------
swapper/2/0 is trying to acquire lock:
ffff888177190110 (&sch->q.lock){+.-.}-{2:2}, at: __dev_queue_xmit+0x1560/0x2e70
but task is already holding lock:
ffff88811995a110 (&sch->q.lock){+.-.}-{2:2}, at: __dev_queue_xmit+0x1560/0x2e70
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&sch->q.lock);
lock(&sch->q.lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
5 locks held by swapper/2/0:
#0: ffff888135a09d98 ((&in_dev->mr_ifc_timer)){+.-.}-{0:0}, at: call_timer_fn+0x11a/0x510
#1: ffffffffaaee5260 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x2c0/0x1ed0
#2: ffffffffaaee5200 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x209/0x2e70
#3: ffff88811995a110 (&sch->q.lock){+.-.}-{2:2}, at: __dev_queue_xmit+0x1560/0x2e70
#4: ffffffffaaee5200 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x209/0x2e70
stack backtrace:
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 6.7.0-rc3+ #598
Hardware name: Red Hat KVM, BIOS 1.13.0-2.module+el8.3.0+7353+9de0a3cc 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x4a/0x80
__lock_acquire+0xfdd/0x3150
lock_acquire+0x1ca/0x540
_raw_spin_lock+0x34/0x80
__dev_queue_xmit+0x1560/0x2e70
tcf_mirred_act+0x82e/0x1260 [act_mirred]
tcf_action_exec+0x161/0x480
tcf_classify+0x689/0x1170
prio_enqueue+0x316/0x660 [sch_prio]
dev_qdisc_enqueue+0x46/0x220
__dev_queue_xmit+0x1615/0x2e70
ip_finish_output2+0x1218/0x1ed0
__ip_finish_output+0x8b3/0x1350
ip_output+0x163/0x4e0
igmp_ifc_timer_expire+0x44b/0x930
call_timer_fn+0x1a2/0x510
run_timer_softirq+0x54d/0x11a0
__do_softirq+0x1b3/0x88f
irq_exit_rcu+0x18f/0x1e0
sysvec_apic_timer_interrupt+0x6f/0x90
</IRQ>
This happens when TC does a mirred egress redirect from the root qdisc of
device A to the root qdisc of device B. As long as these two locks aren't
protecting the same qdisc, they can be acquired in chain: add a per-qdisc
lockdep key to silence false warnings.
This dynamic key should safely replace the static key we have in sch_htb:
it was added to allow enqueueing to the device "direct qdisc" while still
holding the qdisc root lock.
v2: don't use static keys anymore in HTB direct qdiscs (thanks Eric Dumazet)
CC: Maxim Mikityanskiy <maxim@isovalent.com>
CC: Xiumei Mu <xmu@redhat.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/451
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/7dc06d6158f72053cf877a82e2a7a5bd23692faa.1713448007.git.dcaratti@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e894b6005d ]
Several serial drivers want to read the same or similar set of
the port properties. Make a common helper for them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240304123035.758700-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 87d80bfbd5 ("serial: 8250_dw: Don't use struct dw8250_data outside of 8250_dw")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79d713baf6 ]
In some APIs we would like to assign the special value to iotype
and compare against it in another places. Introduce UPIO_UNKNOWN
for this purpose.
Note, we can't use 0, because it's a valid value for IO port access.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240304123035.758700-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 87d80bfbd5 ("serial: 8250_dw: Don't use struct dw8250_data outside of 8250_dw")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 826a5d8c9d ]
Some users want to use the struct device pointer to see if the
device is big endian in terms of Open Firmware specifications,
i.e. if it has a "big-endian" property, or if the kernel was
compiled for BE *and* the device has a "native-endian" property.
Provide inline helper for the users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231025184259.250588-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 87d80bfbd5 ("serial: 8250_dw: Don't use struct dw8250_data outside of 8250_dw")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 806a5198c0 ]
This removes the bogus check for max > hcon->le_conn_max_interval since
the later is just the initial maximum conn interval not the maximum the
stack could support which is really 3200=4000ms.
In order to pass GAP/CONN/CPUP/BV-05-C one shall probably enter values
of the following fields in IXIT that would cause hci_check_conn_params
to fail:
TSPX_conn_update_int_min
TSPX_conn_update_int_max
TSPX_conn_update_peripheral_latency
TSPX_conn_update_supervision_timeout
Link: https://github.com/bluez/bluez/issues/847
Fixes: e4b019515f ("Bluetooth: Enforce validation on max value of connection interval")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ae073f59 ]
When innerprotoinherit is set, the tunneled packets do not have an inner
Ethernet header.
Change 'maclen' to not always assume the header length is ETH_HLEN, as
there might not be a MAC header.
This resolves issues with drivers (e.g. mlx5, in
mlx5e_tx_tunnel_accel()) who rely on the skb inner network header offset
to be correct, and use it for TX offloads.
Fixes: d8a6213d70 ("geneve: fix header validation in geneve[6]_xmit_skb")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89e8a2366e ]
iommu_sva_bind_device() should return either a sva bond handle or an
ERR_PTR value in error cases. Existing drivers (idxd and uacce) only
check the return value with IS_ERR(). This could potentially lead to
a kernel NULL pointer dereference issue if the function returns NULL
instead of an error pointer.
In reality, this doesn't cause any problems because iommu_sva_bind_device()
only returns NULL when the kernel is not configured with CONFIG_IOMMU_SVA.
In this case, iommu_dev_enable_feature(dev, IOMMU_DEV_FEAT_SVA) will
return an error, and the device drivers won't call iommu_sva_bind_device()
at all.
Fixes: 26b25a2b98 ("iommu: Bind process address spaces to devices")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/20240528042528.71396-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da4a827416 ]
We got the following issue in a fuzz test of randomly issuing the restore
command:
==================================================================
BUG: KASAN: slab-use-after-free in cachefiles_ondemand_daemon_read+0xb41/0xb60
Read of size 8 at addr ffff888122e84088 by task ondemand-04-dae/963
CPU: 13 PID: 963 Comm: ondemand-04-dae Not tainted 6.8.0-dirty #564
Call Trace:
kasan_report+0x93/0xc0
cachefiles_ondemand_daemon_read+0xb41/0xb60
vfs_read+0x169/0xb50
ksys_read+0xf5/0x1e0
Allocated by task 116:
kmem_cache_alloc+0x140/0x3a0
cachefiles_lookup_cookie+0x140/0xcd0
fscache_cookie_state_machine+0x43c/0x1230
[...]
Freed by task 792:
kmem_cache_free+0xfe/0x390
cachefiles_put_object+0x241/0x480
fscache_cookie_state_machine+0x5c8/0x1230
[...]
==================================================================
Following is the process that triggers the issue:
mount | daemon_thread1 | daemon_thread2
------------------------------------------------------------
cachefiles_withdraw_cookie
cachefiles_ondemand_clean_object(object)
cachefiles_ondemand_send_req
REQ_A = kzalloc(sizeof(*req) + data_len)
wait_for_completion(&REQ_A->done)
cachefiles_daemon_read
cachefiles_ondemand_daemon_read
REQ_A = cachefiles_ondemand_select_req
msg->object_id = req->object->ondemand->ondemand_id
------ restore ------
cachefiles_ondemand_restore
xas_for_each(&xas, req, ULONG_MAX)
xas_set_mark(&xas, CACHEFILES_REQ_NEW)
cachefiles_daemon_read
cachefiles_ondemand_daemon_read
REQ_A = cachefiles_ondemand_select_req
copy_to_user(_buffer, msg, n)
xa_erase(&cache->reqs, id)
complete(&REQ_A->done)
------ close(fd) ------
cachefiles_ondemand_fd_release
cachefiles_put_object
cachefiles_put_object
kmem_cache_free(cachefiles_object_jar, object)
REQ_A->object->ondemand->ondemand_id
// object UAF !!!
When we see the request within xa_lock, req->object must not have been
freed yet, so grab the reference count of object before xa_unlock to
avoid the above issue.
Fixes: 0a7e54c195 ("cachefiles: resend an open request if the read request's object is closed")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Link: https://lore.kernel.org/r/20240522114308.2402121-5-libaokun@huaweicloud.com
Acked-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Stable-dep-of: 4b4391e77a ("cachefiles: defer exposing anon_fd until after copy_to_user() succeeds")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc5ac966f2 ]
This lets us see the correct trace output.
Fixes: c838305450 ("cachefiles: notify the user daemon when looking up cookie")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Link: https://lore.kernel.org/r/20240522114308.2402121-2-libaokun@huaweicloud.com
Acked-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 90e6f08915 upstream.
The function mpi3mr_qcmd() of the mpi3mr driver is able to indicate to
the HBA if a read or write command directed at an ATA device should be
translated to an NCQ read/write command with the high prioiryt bit set
when the request uses the RT priority class and the user has enabled NCQ
priority through sysfs.
However, unlike the mpt3sas driver, the mpi3mr driver does not define
the sas_ncq_prio_supported and sas_ncq_prio_enable sysfs attributes, so
the ncq_prio_enable field of struct mpi3mr_sdev_priv_data is never
actually set and NCQ Priority cannot ever be used.
Fix this by defining these missing atributes to allow a user to check if
an ATA device supports NCQ priority and to enable/disable the use of NCQ
priority. To do this, lift the function scsih_ncq_prio_supp() out of the
mpt3sas driver and make it the generic SCSI SAS transport function
sas_ata_ncq_prio_supported(). Nothing in that function is hardware
specific, so this function can be used in both the mpt3sas driver and
the mpi3mr driver.
Reported-by: Scott McCoy <scott.mccoy@wdc.com>
Fixes: 023ab2a9b4 ("scsi: mpi3mr: Add support for queue command processing")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240611083435.92961-1-dlemoal@kernel.org
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f4cc33e78b ]
Add support for the Andes hart-level interrupt controller. This
controller provides interrupt mask/unmask functions to access the
custom register (SLIE) where the non-standard S-mode local interrupt
enable bits are located. The base of custom interrupt number is set
to 256.
To share the riscv_intc_domain_map() with the generic RISC-V INTC and
ACPI, add a chip parameter to riscv_intc_init_common(), so it can be
passed to the irq_domain_set_info() as a private data.
Andes hart-level interrupt controller requires the "andestech,cpu-intc"
compatible string to be present in interrupt-controller of cpu node to
enable the use of custom local interrupt source.
e.g.,
cpu0: cpu@0 {
compatible = "andestech,ax45mp", "riscv";
...
cpu0-intc: interrupt-controller {
#interrupt-cells = <0x01>;
compatible = "andestech,cpu-intc", "riscv,cpu-intc";
interrupt-controller;
};
};
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Randolph <randolph@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240222083946.3977135-4-peterlin@andestech.com
Stable-dep-of: 0110c4b110 ("irqchip/riscv-intc: Prevent memory leak when riscv_intc_init_common() fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af66bfd3c8 ]
When removing the inner map from the outer map, the inner map will be
freed after one RCU grace period and one RCU tasks trace grace
period, so it is certain that the bpf program, which may access the
inner map, has exited before the inner map is freed.
However there is no need to wait for one RCU tasks trace grace period if
the outer map is only accessed by non-sleepable program. So adding
sleepable_refcnt in bpf_map and increasing sleepable_refcnt when adding
the outer map into env->used_maps for sleepable program. Although the
max number of bpf program is INT_MAX - 1, the number of bpf programs
which are being loaded may be greater than INT_MAX, so using atomic64_t
instead of atomic_t for sleepable_refcnt. When removing the inner map
from the outer map, using sleepable_refcnt to decide whether or not a
RCU tasks trace grace period is needed before freeing the inner map.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20231204140425.1480317-6-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 2884dc7d08 ("bpf: Fix a potential use-after-free in bpf_link_free()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3c2f8859ae upstream.
This was already defined locally by init/main.c, but let's make
it generic, as arch/x86/kernel/cpu/topology.c is going to make
use of it to have more uniform code.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92f1655aa2 upstream.
__dst_negative_advice() does not enforce proper RCU rules when
sk->dst_cache must be cleared, leading to possible UAF.
RCU rules are that we must first clear sk->sk_dst_cache,
then call dst_release(old_dst).
Note that sk_dst_reset(sk) is implementing this protocol correctly,
while __dst_negative_advice() uses the wrong order.
Given that ip6_negative_advice() has special logic
against RTF_CACHE, this means each of the three ->negative_advice()
existing methods must perform the sk_dst_reset() themselves.
Note the check against NULL dst is centralized in
__dst_negative_advice(), there is no need to duplicate
it in various callbacks.
Many thanks to Clement Lecigne for tracking this issue.
This old bug became visible after the blamed commit, using UDP sockets.
Fixes: a87cb3e48e ("net: Facility to report route quality of connected sockets")
Reported-by: Clement Lecigne <clecigne@google.com>
Diagnosed-by: Clement Lecigne <clecigne@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240528114353.1794151-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[Lee: Stable backport]
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2dc78b86e upstream.
We normally ksm_zero_pages++ in ksmd when page is merged with zero page,
but ksm_zero_pages-- is done from page tables side, where there is no any
accessing protection of ksm_zero_pages.
So we can read very exceptional value of ksm_zero_pages in rare cases,
such as -1, which is very confusing to users.
Fix it by changing to use atomic_long_t, and the same case with the
mm->ksm_zero_pages.
Link: https://lkml.kernel.org/r/20240528-b4-ksm-counters-v3-2-34bb358fdc13@linux.dev
Fixes: e2942062e0 ("ksm: count all zero pages placed by KSM")
Fixes: 6080d19f07 ("ksm: add ksm zero pages for each process")
Signed-off-by: Chengming Zhou <chengming.zhou@linux.dev>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ran Xiaokai <ran.xiaokai@zte.com.cn>
Cc: Stefan Roesch <shr@devkernel.io>
Cc: xu xin <xu.xin16@zte.com.cn>
Cc: Yang Yang <yang.yang29@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79c1374548 upstream.
Add mapping_max_folio_size() to get the maximum folio size for this
pagecache mapping.
Fixes: 5d8edfb900 ("iomap: Copy larger chunks from userspace")
Cc: stable@vger.kernel.org
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240521114939.2541461-1-xu.yang_2@nxp.com
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63a7cd6602 upstream.
Some mmc host drivers may need to fixup a card-detection GPIO's config
to e.g. enable the GPIO controllers builtin pull-up resistor on devices
where the firmware description of the GPIO is broken (e.g. GpioInt with
PullNone instead of PullUp in ACPI DSDT).
Since this is the exception rather then the rule adding a config
parameter to mmc_gpiod_request_cd() seems undesirable, so instead
add a new mmc_gpiod_set_cd_config() function. This is simply a wrapper
to call gpiod_set_config() on the card-detect GPIO acquired through
mmc_gpiod_request_cd().
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240410191639.526324-2-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f592cc5794 upstream.
Each RPMh VRM accelerator resource has 3 or 4 contiguous 4-byte aligned
addresses associated with it. These control voltage, enable state, mode,
and in legacy targets, voltage headroom. The current in-flight request
checking logic looks for exact address matches. Requests for different
addresses of the same RPMh resource as thus not detected as in-flight.
Add new cmd-db API cmd_db_match_resource_addr() to enhance the in-flight
request check for VRM requests by ignoring the address offset.
This ensures that only one request is allowed to be in-flight for a given
VRM resource. This is needed to avoid scenarios where request commands are
carried out by RPMh hardware out-of-order leading to LDO regulator
over-current protection triggering.
Fixes: 658628e7ef ("drivers: qcom: rpmh-rsc: add RPMH controller for QCOM SoCs")
Cc: stable@vger.kernel.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Elliot Berman <quic_eberman@quicinc.com> # sm8650-qrd
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20240215-rpmh-rsc-fixes-v4-1-9cbddfcba05b@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b9f86c6d5 ]
The MTMP register (0x900a) capability offset is off-by-one, move it to
the right place.
Fixes: 1f507e80c7 ("net/mlx5: Expose NIC temperature via hardware monitoring kernel API")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6309727ef2 ]
Add a kthread_stop_put() helper that stops a thread and puts its task
struct. Use it to replace the various instances of kthread_stop()
followed by put_task_struct().
Remove the kthread_stop_put() macro in usbip that is similar but doesn't
return the result of kthread_stop().
[agruenba@redhat.com: fix kerneldoc comment]
Link: https://lkml.kernel.org/r/20230911111730.2565537-1-agruenba@redhat.com
[akpm@linux-foundation.org: document kthread_stop_put()'s argument]
Link: https://lkml.kernel.org/r/20230907234048.2499820-1-agruenba@redhat.com
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: bb9025f443 ("dma-mapping: benchmark: fix up kthread-related error handling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e577732e8 ]
After commit 69d4c0d321 ("entry, kasan, x86: Disallow overriding mem*()
functions") and the follow-up fixes, with CONFIG_FORTIFY_SOURCE enabled,
even though the compiler instruments meminstrinsics by generating calls to
__asan/__hwasan_ prefixed functions, FORTIFY_SOURCE still uses
uninstrumented memset/memmove/memcpy as the underlying functions.
As a result, KASAN cannot detect bad accesses in memset/memmove/memcpy.
This also makes KASAN tests corrupt kernel memory and cause crashes.
To fix this, use __asan_/__hwasan_memset/memmove/memcpy as the underlying
functions whenever appropriate. Do this only for the instrumented code
(as indicated by __SANITIZE_ADDRESS__).
Link: https://lkml.kernel.org/r/20240517130118.759301-1-andrey.konovalov@linux.dev
Fixes: 69d4c0d321 ("entry, kasan, x86: Disallow overriding mem*() functions")
Fixes: 51287dcb00 ("kasan: emit different calls for instrumentable memintrinsics")
Fixes: 36be5cba99 ("kasan: treat meminstrinsic as builtins in uninstrumented files")
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Reported-by: Nico Pache <npache@redhat.com>
Closes: https://lore.kernel.org/all/20240501144156.17e65021@outsider.home/
Reviewed-by: Marco Elver <elver@google.com>
Tested-by: Nico Pache <npache@redhat.com>
Acked-by: Nico Pache <npache@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5e3df06ac ]
In MIPI I3C Specification:
"Ninth Bit of SDR Target Returned (Read) Data as End-of-Data: In I2C, the
ninth Data bit from Target to Controller is an ACK by the Controller. By
contrast, in I3C this bit allows the Target to end a Read, and allows the
Controller to Abort a Read. In SDR terms, the ninth bit of Read data is
referred to as the T-Bit (for ‘Transition’)"
I3C allow devices early terminate data transfer. So need "actual_len" field
to indicate how much get by i3c_priv_xfer.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-4-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Stable-dep-of: 7f3d633b46 ("i3c: master: svc: change ENXIO to EAGAIN when IBI occurs during start frame")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4f4276f98 ]
Some PMICs treat the vsel_reg same as apply-bit. Eg, when voltage range
is changed, the new voltage setting is not taking effect until the vsel
register is written.
Add a flag 'range_applied_by_vsel' to the regulator desc to indicate this
behaviour and to force the vsel value to be written to hardware if range
was changed, even if the old selector was same as the new one.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://msgid.link/r/ZktCpcGZdgHWuN_L@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 1ace99d7c7 ("regulator: tps6287x: Force writing VSEL bit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b195acf526 ]
Calibrated data will be set to default after loading DSP config params,
which will cause speaker protection work abnormally. Reload calibrated
data after loading DSP config params. Remove declaration of unused API
which load calibrated data in wrong sequence, changed the copyright year
and correct file name in license
header.
Fixes: ef3bcde75d ("ASoC: tas2781: Add tas2781 driver")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://msgid.link/r/20240518141546.1742-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aed9a1a4f7 ]
Allow PTE kind and tile mode on BO create with VM_BIND, and add a
GETPARAM to indicate this change. This is needed to support modifiers in
NVK and ensure correctness when dealing with the nouveau GL driver.
The userspace modifiers implementation this is for can be found here:
https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/24795
Fixes: b88baab828 ("drm/nouveau: implement new VM_BIND uAPI")
Signed-off-by: Mohamed Ahmed <mohamedahmedegypt2001@gmail.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collabora.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240509204352.7597-1-mohamedahmedegypt2001@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72fa02fdf8 ]
This reports the currently used vram allocations.
userspace using this has been proposed for nvk, but
it's a rather trivial uapi addition.
Reviewed-by: Faith Ekstrand <faith.ekstrand@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Stable-dep-of: aed9a1a4f7 ("drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f4d8aac6e ]
This returns the BAR resources size so userspace can make
decisions based on rebar support.
userspace using this has been proposed for nvk, but
it's a rather trivial uapi addition.
Reviewed-by: Faith Ekstrand <faith.ekstrand@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Stable-dep-of: aed9a1a4f7 ("drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72a77d7631 ]
Add a dummy SUPPLY widget connected to the ASP that forces the
chip registers to match the regmap cache when the ASP is
powered-up.
On a SoundWire system the ASP is free for use as a chip-to-chip
interconnect. This can be either for the firmware on multiple
CS35L56 to share reference audio; or as a bridge to another
device. If it is a firmware interconnect it is owned by the
firmware and the Linux driver should avoid writing the registers.
However. If it is a bridge then Linux may take over and handle
it as a normal codec-to-codec link.
CS35L56 is designed for SDCA and a generic SDCA driver would
know nothing about these chip-specific registers. So if the
ASP is being used on a SoundWire system the firmware sets up the
ASP registers. This means that we can't assume the default
state of the ASP registers. But we don't know the initial state
that the firmware set them to until after the firmware has been
downloaded and booted, which can take several seconds when
downloading multiple amps.
To avoid blocking probe() for several seconds waiting for the
firmware, the silicon defaults are assumed. This allows the machine
driver to setup the ASP configuration during probe() without being
blocked. If the ASP is hooked up and used, the SUPPLY widget
ensures that the chip registers match what was configured in the
regmap cache.
If the machine driver does not hook up the ASP, it is assumed that
it won't call any functions to configure the ASP DAI. Therefore
the regmap cache will be clean for these registers so a
regcache_sync() will not overwrite the chip registers. If the
DAI is not hooked up, the dummy SUPPLY widget will not be
invoked so it will never force-overwrite the chip registers.
Backport note:
This won't apply cleanly to kernels older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-8-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: d344873c4c ("ALSA: hda: cs35l56: Fix lifetime of cs_dsp instance")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c82aac10 ]
Keep track if cec_claim_log_addrs() is running, and return -EBUSY
if it is when calling CEC_ADAP_S_LOG_ADDRS.
This prevents a case where cec_claim_log_addrs() could be called
while it was still in progress.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Yang, Chenyuan <cy54@illinois.edu>
Closes: https://lore.kernel.org/linux-media/PH7PR11MB57688E64ADE4FE82E658D86DA09EA@PH7PR11MB5768.namprd11.prod.outlook.com/
Fixes: ca684386e6 ("[media] cec: add HDMI CEC framework (api)")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 009905ec50 ]
The subdev .s_stream() operation must not be called to start an already
started subdev, or stop an already stopped one. This requirement has
never been formally documented. Fix it, and catch possible offenders
with a WARN_ON() in the call_s_stream() wrapper.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stable-dep-of: f2bf6cd8f4 ("media: v4l: Don't turn on privacy LED if streamon fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b63db58e2f ]
Synthetic events create and destroy tracefs files when they are created
and removed. The tracing subsystem has its own file descriptor
representing the state of the events attached to the tracefs files.
There's a race between the eventfs files and this file descriptor of the
tracing system where the following can cause an issue:
With two scripts 'A' and 'B' doing:
Script 'A':
echo "hello int aaa" > /sys/kernel/tracing/synthetic_events
while :
do
echo 0 > /sys/kernel/tracing/events/synthetic/hello/enable
done
Script 'B':
echo > /sys/kernel/tracing/synthetic_events
Script 'A' creates a synthetic event "hello" and then just writes zero
into its enable file.
Script 'B' removes all synthetic events (including the newly created
"hello" event).
What happens is that the opening of the "enable" file has:
{
struct trace_event_file *file = inode->i_private;
int ret;
ret = tracing_check_open_get_tr(file->tr);
[..]
But deleting the events frees the "file" descriptor, and a "use after
free" happens with the dereference at "file->tr".
The file descriptor does have a reference counter, but there needs to be a
way to decrement it from the eventfs when the eventfs_inode is removed
that represents this file descriptor.
Add an optional "release" callback to the eventfs_entry array structure,
that gets called when the eventfs file is about to be removed. This allows
for the creating on the eventfs file to increment the tracing file
descriptor ref counter. When the eventfs file is deleted, it can call the
release function that will call the put function for the tracing file
descriptor.
This will protect the tracing file from being freed while a eventfs file
that references it is being opened.
Link: https://lore.kernel.org/linux-trace-kernel/20240426073410.17154-1-Tze-nan.Wu@mediatek.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240502090315.448cba46@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 5790b1fb3d ("eventfs: Remove eventfs_file and just use eventfs_inode")
Reported-by: Tze-nan wu <Tze-nan.Wu@mediatek.com>
Tested-by: Tze-nan Wu (吳澤南) <Tze-nan.Wu@mediatek.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c748a6d77c ]
In order to introduce a pwm api which can be used from atomic context,
we will need two functions for applying pwm changes:
int pwm_apply_might_sleep(struct pwm *, struct pwm_state *);
int pwm_apply_atomic(struct pwm *, struct pwm_state *);
This commit just deals with renaming pwm_apply_state(), a following
commit will introduce the pwm_apply_atomic() function.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> # for input
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Stable-dep-of: 974afccd37 ("leds: pwm: Disable PWM when going to suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7c0e1ecee ]
The current implementation of the fpga region assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the region
during programming if the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_region
struct and use it to take the module's refcount. Modify the functions for
registering a region to take an additional owner module parameter and
rename them to avoid conflicts. Use the old function names for helper
macros that automatically set the module that registers the region as the
owner. This ensures compatibility with existing low-level control modules
and reduces the chances of registering a region without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga region.
Fixes: 0fa20cdfcc ("fpga: fpga-region: device tree control for FPGA")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Russ Weight <russ.weight@linux.dev>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240419083601.77403-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 794ef0e578 ]
Move to the IIO backend framework. Devices supported by adi-axi-adc now
register themselves as backend devices.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240210-iio-backend-v11-7-f5242a5fb42a@analog.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: cf1c833f89 ("iio: adc: adi-axi-adc: only error out in major version mismatch")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a97905d3e ]
This is a Framework to handle complex IIO aggregate devices.
The typical architecture is to have one device as the frontend device which
can be "linked" against one or multiple backend devices. All the IIO and
userspace interface is expected to be registers/managed by the frontend
device which will callback into the backends when needed (to get/set
some configuration that it does not directly control).
The basic framework interface is pretty simple:
- Backends should register themselves with @devm_iio_backend_register()
- Frontend devices should get backends with @devm_iio_backend_get()
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240210-iio-backend-v11-5-f5242a5fb42a@analog.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: cf1c833f89 ("iio: adc: adi-axi-adc: only error out in major version mismatch")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c446288d7 ]
Export iio_dmaengine_buffer_free() and iio_dmaengine_buffer_alloc().
This is in preparation of introducing IIO backends support. This will
allow us to allocate a buffer and control it's lifetime from a device
different from the one holding the DMA firmware properties. Effectively,
in this case the struct device holding the firmware information about
the DMA channels is not the same as iio_dev->dev.parent (typical case).
While at it, namespace the buffer-dmaengine exports and update the
current user of these buffers.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240210-iio-backend-v11-4-f5242a5fb42a@analog.com
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: cf1c833f89 ("iio: adc: adi-axi-adc: only error out in major version mismatch")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 416bdb8960 ]
Remove the @priv: line to prevent the kernel-doc warning:
include/linux/counter.h:400: warning: Excess struct member 'priv' description in 'counter_device'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: f2ee4759fb ("counter: remove old and now unused registration API")
Link: https://lore.kernel.org/r/20231223050511.13849-1-rdunlap@infradead.org
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1da11f8220 ]
The current implementation of the fpga bridge assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the bridge if
the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_bridge
struct and use it to take the module's refcount. Modify the function for
registering a bridge to take an additional owner module parameter and
rename it to avoid conflicts. Use the old function name for a helper macro
that automatically sets the module that registers the bridge as the owner.
This ensures compatibility with existing low-level control modules and
reduces the chances of registering a bridge without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga bridge.
Other changes: opportunistically move put_device() from __fpga_bridge_get()
to fpga_bridge_get() and of_fpga_bridge_get() to improve code clarity since
the bridge device is taken in these functions.
Fixes: 21aeda950c ("fpga: add fpga bridge framework")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Russ Weight <russ.weight@linux.dev>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240322171839.233864-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d4d2d4346 ]
The current implementation of the fpga manager assumes that the low-level
module registers a driver for the parent device and uses its owner pointer
to take the module's refcount. This approach is problematic since it can
lead to a null pointer dereference while attempting to get the manager if
the parent device does not have a driver.
To address this problem, add a module owner pointer to the fpga_manager
struct and use it to take the module's refcount. Modify the functions for
registering the manager to take an additional owner module parameter and
rename them to avoid conflicts. Use the old function names for helper
macros that automatically set the module that registers the manager as the
owner. This ensures compatibility with existing low-level control modules
and reduces the chances of registering a manager without setting the owner.
Also, update the documentation to keep it consistent with the new interface
for registering an fpga manager.
Other changes: opportunistically move put_device() from __fpga_mgr_get() to
fpga_mgr_get() and of_fpga_mgr_get() to improve code clarity since the
manager device is taken in these functions.
Fixes: 654ba4cc0f ("fpga manager: ensure lifetime with of_fpga_mgr_get")
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20240305192926.84886-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dbd04eddb ]
There are several scenarios that have come up where having a user_event
persist even if the process that registered it exits. The main one is
having a daemon create events on bootup that shouldn't get deleted if
the daemon has to exit or reload. Another is within OpenTelemetry
exporters, they wish to potentially check if a user_event exists on the
system to determine if exporting the data out should occur. The
user_event in this case must exist even in the absence of the owning
process running (such as the above daemon case).
Expose the previously internal flag USER_EVENT_REG_PERSIST to user
processes. Upon register or delete of events with this flag, ensure the
user is perfmon_capable to prevent random user processes with access to
tracefs from creating events that persist after exit.
Link: https://lkml.kernel.org/r/20230912180704.1284-2-beaub@linux.microsoft.com
Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Stable-dep-of: bd125a0840 ("tracing/user_events: Fix non-spaced field matching")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48f996d4ad ]
Rounding up the queue depth to power of two is not a hardware requirement.
In order to optimize the per connection memory usage, removing drivers
implementation which round up to the queue depths to the power of 2.
Implements a mask to maintain backward compatibility with older
library.
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1698069803-1787-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Stable-dep-of: 78cfd17142 ("bnxt_re: avoid shift undefined behavior in bnxt_qplib_alloc_init_hwq")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0a200ab4b ]
DisplayID spec v1.3 revision history notes do claim that
the toplogy block was added in v1.3 so requiring structure
v1.2 would seem correct, but there is at least one EDID in
edid.tv with a topology block and structure v1.0. And
there are also EDIDs with DisplayID structure v1.3 which
seems to be totally incorrect as DisplayID spec v1.3 lists
structure v1.2 as the only legal value.
Unfortunately I couldn't find copies of DisplayID spec
v1.0-v1.2 anywhere (even on vesa.org), so I'll have to
go on empirical evidence alone.
We used to parse the topology block on all v1.x
structures until the check for structure v2.0 was added.
Let's go back to doing that as the evidence does suggest
that there are DisplayIDs in the wild that would miss
out on the topology stuff otherwise.
Also toss out DISPLAY_ID_STRUCTURE_VER_12 entirely as
it doesn't appear we can really use it for anything.
I *think* we could technically skip all the structure
version checks as the block tags shouldn't conflict
between v2.0 and v1.x. But no harm in having a bit of
extra sanity checks I guess.
So far I'm not aware of any user reported regressions
from overly strict check, but I do know that it broke
igt/kms_tiled_display's fake DisplayID as that one
gets generated with structure v1.0.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Fixes: c5a486af9d ("drm/edid: parse Tiled Display Topology Data Block for DisplayID 2.0")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240410180139.21352-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de1c705c50 ]
The functions mipi_dsi_compression_mode() and
mipi_dsi_picture_parameter_set() return 0-or-error rather than a buffer
size. Follow example of other similar MIPI DSI functions and use int
return type instead of size_t.
Fixes: f4dea1aaa9 ("drm/dsi: add helpers for DSI compression mode and PPS packets")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240408-lg-sw43408-panel-v5-2-4e092da22991@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58300f8d6a ]
The string SND_SOC_DAPM_DIR_OUT is printed in the snd_soc_dapm_path trace
event instead of its value:
(((REC->path_dir) == SND_SOC_DAPM_DIR_OUT) ? "->" : "<-")
User space cannot parse this, as it has no idea what SND_SOC_DAPM_DIR_OUT
is. Use TRACE_DEFINE_ENUM() to convert it to its value:
(((REC->path_dir) == 1) ? "->" : "<-")
So that user space tools, such as perf and trace-cmd, can parse it
correctly.
Reported-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Fixes: 6e588a0d83 ("ASoC: dapm: Consolidate path trace events")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20240416000303.04670cdf@rorschach.local.home
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8df1ddb5bf ]
If an eDP panel is not powered on then any attempts to talk to it over
the DP AUX channel will timeout. Unfortunately these attempts may be
quite slow. Userspace can initiate these attempts either via a
/dev/drm_dp_auxN device or via the created i2c device.
Making the DP AUX drivers timeout faster is a difficult proposition.
In theory we could just poll the panel's HPD line in the AUX transfer
function and immediately return an error there. However, this is
easier said than done. For one thing, there's no hard requirement to
hook the HPD line up for eDP panels and it's OK to just delay a fixed
amount. For another thing, the HPD line may not be fast to probe. On
parade-ps8640 we need to wait for the bridge chip's firmware to boot
before we can get the HPD line and this is a slow process.
The fact that the transfers are taking so long to timeout is causing
real problems. The open source fwupd daemon sometimes scans DP busses
looking for devices whose firmware need updating. If it happens to
scan while a panel is turned off this scan can take a long time. The
fwupd daemon could try to be smarter and only scan when eDP panels are
turned on, but we can also improve the behavior in the kernel.
Let's let eDP panels drivers specify that a panel is turned off and
then modify the common AUX transfer code not to attempt a transfer in
this case.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Eizan Miyamoto <eizan@chromium.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202141109.1.I24277520ac754ea538c9b14578edc94e1df11b48@changeid
Stable-dep-of: 5e842d55ba ("drm/panel: atna33xc20: Fix unbalanced regulator in the case HPD doesn't assert")
Signed-off-by: Sasha Levin <sashal@kernel.org>
