Commit graph

335,802 commits

Author SHA1 Message Date
Daniel Kurtz
b19fc9ec24 Input: atmel_mxt_ts - add sysfs entries to read fw and hw version
Make firmware and hardware version strings available to userspace.
This is useful, for example, to allow a userspace program to implement
a firwmare update policy.

Change-Id: I1eddb4bbf5f3f9ae6947a8528598973ddead18cf
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:05 +02:00
Daniel Kurtz
e0e0269f34 Input: atmel_mxt_ts - update driver ID info logging
Print unsigned values as '%u'.
Also, parse and print the firmware version in its canonical format, as
suggested by Nick Dyer.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:04 +02:00
Daniel Kurtz
23003a8496 Input: atmel_mxt_ts - read ID information block in one i2c transaction
Reading the whole info block in one i2c transaction speeds up driver
probe significantly, especially on slower i2c busses.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:04 +02:00
Daniel Kurtz
cf94bc09c8 Input: atmel_mxt_ts - optimize writing of object table entries
Write each object using a single bulk i2c write transfer.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:04 +02:00
Daniel Kurtz
9638ab7c9c Input: atmel_mxt_ts - add variable length __mxt_write_reg
The i2c bus requires 4 bytes to do a 1-byte write
(1 byte i2c address + 2 byte offset + 1 byte data).

By taking a length with writes, the driver can amortize transaction
overhead by performing larger transactions where appropriate.

This patch just sets up the new API.  Later patches refactor writes
to take advantage of the larger transactions.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:04 +02:00
Daniel Kurtz
771733e348 Input: atmel_mxt_ts - return errors from i2c layer
The i2c layer can report a variety of errors, including -ENXIO for an i2c
NAK.  Instead of treating them all as -EIO, pass the actual i2c layer
error up to the caller.

However, still report as -EIO the unlikely case that a transaction was
partially completed, and no error message was returned from i2c_*().

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:03 +02:00
Daniel Kurtz
794eb67e76 Input: atmel_mxt_ts - print all instances when dumping objects
For objects with multiple instances, dump them all, prepending each with
its "Instance #".

[rydberg@euromail.se: break out mxt_show_instance()]
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:03 +02:00
Daniel Kurtz
91630955cb Input: atmel_mxt_ts - print less overhead when dumping objects
Conserve limited (PAGE_SIZE) sysfs output buffer space by only showing
readable objects and not printing the object's index, which is not useful
to userspace.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:03 +02:00
Daniel Kurtz
43a91d51d3 Input: atmel_mxt_ts - optimize reading objects in object sysfs entry
Read each object in a single i2c transaction instead of byte-by-byte

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:03 +02:00
Daniel Kurtz
9c67b789e0 Input: atmel_mxt_ts - use scnprintf for object sysfs entry
Using scnprintf() is a cleaner way to ensure that we don't overwrite the
PAGE_SIZE sysfs output buffer.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:03 +02:00
Daniel Kurtz
55d6867fe6 Input: atmel_mxt_ts - don't read T5 when dumping objects
T5 is the message processor object.  Reading it will only have two
outcomes, neither of which is particularly useful:
 1) the message count decrements, and a valid message will be lost
 2) an invalid message will be read (reportid == 0xff)

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:02 +02:00
Daniel Kurtz
6399003800 Input: atmel_mxt_ts - warn if sysfs could not be created
If sysfs entry creation fails, the driver is still usable, so don't
just abort probe.  Just warn and continue.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:02 +02:00
Daniel Kurtz
e1e1658d2e Input: atmel_mxt_ts - detect OOM when creating mt slots
Hopefully this new code path will never be used, but better safe than
sorry...

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:02 +02:00
Daniel Kurtz
c2ef9a1a24 Input: atmel_mxt_ts - use client name for irq
The atmel_mxt_ts driver can support multiple devices simultaneously.
Use the i2c_client name instead of the driver name when requesting an
interrupt to make the different interrupts distinguishable in
/proc/interrupts and top.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:02 +02:00
Daniel Kurtz
ec02ac2b7e Input: atmel_mxt_ts - derive phys from i2c client adapter
This allows userspace to more easily distinguish which bus a particular
atmel_mxt_ts device is attached to.

The resulting phys will be something like:
 i2c-1-0067/input0

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-06-29 15:58:01 +02:00
Ingo Molnar
add79461a2 perf/core improvements and fixes:
. Improve 'perf bench' docs, by Namhyung Kim
 
 . Fix build when O= is not used, from David Ahern
 
 . Fix cross compilation build, from Namhyung Kim
 
 . Fix pipe mode when callchains are used, from David Ahern
 
 . Follow .gnu_debuglink section to find separate symbols, from Pierre-Loup A. Griffais
 
 . Fix 'perf test' raw events entries, from Jiri Olsa
 
 . Use the events description in the perf.data file, not the sysfs ones.
 
 Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.14 (GNU/Linux)
 
 iQIcBAABAgAGBQJP61nAAAoJENZQFvNTUqpA1iQQAKFv7R0GsGpC5bIVTUFmDGMX
 PL+XJ6b9vx4Ut0p+GO2v0gUSkuyRAL1LLxQDgWks2jgeOSagJE430LYiSrwv5omn
 on1rkoGCGk9+TOnlR2E/OQZOlRQUN3/rIXbY3WEKDb/kU2pevFfgYFFXpC2qPoYm
 4otgfCyYVnzgvgoDj3CbFhQ6gCYLSZmw3WdPmoCPDWBLYMLX9OD10Q+ylg/GOrcG
 05GwkEJyjt9pMGJKo4FVWkoPKyL1UwEVhRm/rW4VqnvHOUPm45MK3j3M35yGlsLI
 9tDUkSygr0kGayyJyq1+1FtdZoYbCc49EgxKDtS47wvEyZ88N8v4mhUx45Fqb/2A
 5AJecv4F9N1PoJALuFVs2OPdWJ78eEijzpFouQxd4OxHakvx8VE1EKVvrCL24uuf
 EpFn6TPnGFvZLCAsnviWdPkph8EpoP43IQtrYJu7N6zE83m7b51k8aytXS4zxZzZ
 pbK2okMCT+mD6SRLGwXC5Sj6nl53KPl8K0JNuTX8ytEU22wtLDqzB2w7Hafhmrrd
 KCyBYlwfiEpiqvTE5AoPBWZgxOHrTEBzinglvWwaBCHI5ua5nxW2chH8rc0fhG9Z
 8T2AsYqahmOF2WVHgJsBKoM3SjcIO1QFFOCymt3HP4YTwYXgzBQi1cNThWZNxmE8
 AKU2+40KOuegGgy3qVzD
 =Hpga
 -----END PGP SIGNATURE-----

Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core

perf/core improvements and fixes:

 * Improve 'perf bench' docs, by Namhyung Kim

 * Fix build when O= is not used, from David Ahern

 * Fix cross compilation build, from Namhyung Kim

 * Fix pipe mode when callchains are used, from David Ahern

 * Follow .gnu_debuglink section to find separate symbols, from Pierre-Loup A. Griffais

 * Fix 'perf test' raw events entries, from Jiri Olsa

 * Use the events description in the perf.data file, not the sysfs ones.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2012-06-29 15:11:26 +02:00
Tony Lindgren
f6f1f12f6d Some OMAP AM35xx fixes.
The powerdomain and clockdomain data for the AM35xx are finally fixed.
 The AM35xx EMAC/MDIO Ethernet controller integration code has been
 converted to use the OMAP device and hwmod framework.  Also the UART4
 and HSOTGUSB warnings have been fixed.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJP7BHOAAoJEMePsQ0LvSpLCrcP/RwJliq2ITgQMEj3N2BbDkKP
 kvS63qYv+QqH+mhGm/RFrmB/p3LSxgOkgdQByavfsQnsE0v5+FYjDnXAB3tvUVHI
 Tv9vSJLIAgC9n4Z8pdJ8u71VGu8XVYnGnCKNz6UhVfHX8Q5BEs01eSPw3wgDVTIq
 gKpMHaeNdi4Atkh2KmxyLwEBF9QC+vSNxMtkqcYbT5faBrqOEKeLz5igG8+VQBTU
 RNeUOHb99+Rf/H2eRsynwMgX63xMzh7hSwW2GAJ5O7+uoMLmdPuI7MUAQR/zcPzQ
 gmFUb1yKkmvu9OKtNR+3VCgGGlvvhaJBwTFJj9IL10xrj4LnDlA3N9bC9vwHG8zw
 0YbrPA2iLU6ufdmLf5rANQFJL3ttg65MZTsjA8q3tjE04QkJncRpDtzr89dQYw/C
 hv3vqCYpo0b2UCMPcyf4pUR5rzzHjPiM4Np9GEj3Ak1puUASwNXGTvXWusWXND9i
 ixcFxd6LppyIa8FxMKXONEGaeNKbp+T63EugBCDEeCCWkXXQQGXU54xWy7w939ib
 pvDtk1+ZqHC5rzPfuNokD+H95W3pc5AYr2pPjW8fctH6Wp9dFZV8sg77pgbenS/E
 u2UX5N7rlqtj/Km7fJgy6h3EUVg8ky6W5nMtF2Jad8D89FOZHoSRAICPA4dIxTYl
 hvv7kdtT23AqZKbxQUNu
 =2b0z
 -----END PGP SIGNATURE-----

Merge tag 'omap-devel-d-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes-non-critical

Some OMAP AM35xx fixes.

The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework.  Also the UART4
and HSOTGUSB warnings have been fixed.
2012-06-29 06:07:08 -07:00
Jean Pihet
bb0adf6ca6 ARM: OMAP2+: do not allow SmartReflex to be built as a module
Disable the module option for POWER_AVS since this is currently not
supported.

This patch fixes these error in the case POWER_AVS is set to 'm':

arch/arm/mach-omap2/built-in.o: In function `sr_class3_configure':
arch/arm/mach-omap2/smartreflex-class3.c:43: undefined reference to `sr_configure_errgen'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_disable':
arch/arm/mach-omap2/smartreflex-class3.c:33: undefined reference to `sr_disable_errgen'
arch/arm/mach-omap2/smartreflex-class3.c:35: undefined reference to `sr_disable'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_enable':
arch/arm/mach-omap2/smartreflex-class3.c:28: undefined reference to `sr_enable'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_init':
arch/arm/mach-omap2/smartreflex-class3.c:59: undefined reference to `sr_register_class'

Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated to use relative paths for the build error]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2012-06-29 05:54:31 -07:00
Kevin Hilman
e0246e8eca ARM: OMAP2+: fix CONFIG_CPU_IDLE dependency on CONFIG_PM
commit 164e0cbf60 (ARM: OMAP3/4: consolidate cpuidle Makefile) added
an OMAP-specific dependency from CPU_IDLE to CONFIG_PM.  This causes
some randconfig warnings when CONFIG_PM has unmet dependencies:

warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)

Fix this by making the dependency on CONFIG_PM_RUNTIME (which in turn
will enable CONFIG_PM.)

Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2012-06-29 05:48:26 -07:00
Jiri Kosina
59f91e5dd0 Merge branch 'master' into for-next
Conflicts:
	include/linux/mmzone.h

Synced with Linus' tree so that trivial patch can be applied
on top of up-to-date code properly.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
2012-06-29 14:45:58 +02:00
Johannes Berg
346c265a48 iwlwifi: fix debug message level
Debug messages should be printed using dev_dbg() not
dev_err() which requires DEBUG to be defined.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 14:28:59 +02:00
Johannes Berg
d6f1c31634 iwlwifi: add trailing newline to some messages
Some messages were missing a trailing newline, add it.

Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 14:28:05 +02:00
Michal Kazior
e4e32459c2 cfg80211: respect iface combinations when starting operation
devlist_mtx locking is changed to accomodate changes.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:19 +02:00
Michal Kazior
d4e50c5917 cfg80211: add channel checking for iface combinations
.connect cannot be handled since the driver scans
and connects on its own. It is up to the driver
then to refuse a connection (with -EBUSY for
example).

Non-fixed channel IBSSes always take a single
channel resource. For example two non-fixed
channel IBSSes always take up 2
num_different_channels, even if they operate on
the same channel at a given point of time.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:19 +02:00
Michal Kazior
2e165b8184 cfg80211/mac80211: remove .get_channel
We do not need it anymore since cfg80211 tracks
monitor channel and monitor channel type.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:18 +02:00
Michal Kazior
a69b40a95b cfg80211: set initial monitor channel
Implements behaviour seen in mac80211. A running
monitor always has a channel - even before
.set_channel. This way we won't break current
behaviour.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:18 +02:00
Michal Kazior
b78e8ceac2 cfg80211: track monitor channel
Make it even more obvious we support single
monitor channel. This will allow us to remove
.get_channel.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:17 +02:00
Michal Kazior
4f03c1ed89 cfg80211: refuse to .set_monitor_channel when non-monitors are present
Having .set_monitor_channel work with non-monitor
interfaces running would make interface
combinations accounting ambiguous.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:17 +02:00
Michal Kazior
870d37fc22 mac80211: refactor virtual monitor code
Use cfg80211 the new .set_monitor_enabled instead
of tracking it inside mac80211.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:16 +02:00
Michal Kazior
dbbae26afa cfg80211: track monitor interfaces count
Implements .set_monitor_enabled(wiphy, enabled).

Notifies driver upon change of interface layout.

If only monitor interfaces become present it is
called with 2nd argument being true. If
non-monitor interface appears then 2nd argument
is false. Driver is notified only upon change.

This makes it more obvious about the fact that
cfg80211 supports single monitor channel. Once we
implement multi-channel we don't want to allow
setting monitor channel while other interface
types are running. Otherwise it would be ambiguous
once we start considering num_different_channels.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:16 +02:00
Michal Kazior
26ab9a0c58 cfg80211: introduce cfg80211_get_chan_state
Helper function for finding out which channel is
used by a given interface.

An exclusive channel can be used only by a single
interface. This is mainly for non-fixed channel
IBSS handling.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:16 +02:00
Michal Kazior
c30a3d3868 cfg80211: track ibss fixed channel
IBSS may hop between channels. It is necessary to
account this special case when considering
interface combinations.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:15 +02:00
Michal Kazior
f4489ebeff cfg80211: add channel tracking for AP and mesh
We need to know which channel is used by a running
AP and mesh for channel context accounting and
finding matching/active interface combination.

STA/IBSS have current_bss already which allows us
to check which channel a vif is tuned to.
Non-fixed channel IBSS can be handled with
additional changes.

Monitor mode is going to be handled differently.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:15 +02:00
Michal Kazior
ac800140c2 cfg80211: .stop_ap when interface is going down
We'll need this for proper channel tracking (which
is going to be needed for channel context
accounting and finding matching/active interface
combination).

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:15 +02:00
Michal Kazior
60771780c2 cfg80211: introduce cfg80211_stop_ap
This functionality will be reused when interface
is going down. Avoids code duplication. Also adds
missing wdev locking.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:14 +02:00
Tomi Valkeinen
974a65825e Merge "Apply LCD manager related parameters" from Archit
The LCD interface drivers(DPI, DSI, RFBI, SDI) do some direct DISPC register
writes to configure LCD manager related fields. This series groups these fields
into a single struct, and let's the interface driver apply these parameters.

This allows us to:

- Check the LCD manager related parameters before applying them.
- Remove some omap_dss_device references as APPLY holds the applied parameters.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-06-29 14:13:07 +03:00
Tomasz Bursztyka
4009e18851 netfilter: nfnetlink: fix missing rcu_read_unlock in nfnetlink_rcv_msg
Bug added in commit 6b75e3e8d6 (netfilter: nfnetlink: add RCU in
nfnetlink_rcv_msg())

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-06-29 13:04:16 +02:00
Tomasz Bursztyka
d31f4d448f netfilter: ipset: fix crash if IPSET_CMD_NONE command is sent
This patch fixes a crash if that ipset command is sent over nfnetlink.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-06-29 13:04:04 +02:00
Archit Taneja
6c6f510afb OMAPDSS: OVERLAY: Clean up replication checking
Replication logic for an overlay depends on the color mode in which it is
configured and the video port width of the manager it is connected to.

video port width now held in dss_lcd_mgr_config in the manager's private
data in APPLY. Use this instead of referring to the omap_dss_device connected to
the manager.

Replication is enabled in the case of TV manager, the video_port_width is set to
a default value of 24 for TV manager.

Make the replication checking an overlay function since it's more of an overlay
characteristic than a display characteristic.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 16:27:59 +05:30
Archit Taneja
c47cdb3088 OMAPDSS: RFBI: Use dss_mgr_enable to enable the overlay manager
The RFBI driver uses a direct DISPC register write to enable the overlay
manager. Replace this with dss_mgr_enable() which checks if the connected
overlay and managers are correctly configured, and configure DSS for
fifomerge.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 16:27:59 +05:30
Archit Taneja
dd88b7a677 OMAPDSS: DISPC: Remove a redundant function
dss_mgr_is_lcd() available in dss.h does the same thing as dispc_mgr_is_lcd()
in dispc.c. Remove the function from dispc.c and replace it with the one in
dss.h.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 16:27:58 +05:30
Archit Taneja
75bac5d1a2 OMAPDSS: APPLY: Remove usage of omap_dss_device from manual/auto update checks
APPLY needs to know at certain places whether an overlay manager is in manual
or auto update mode. The caps of the connected omap_dss_device were used to
check that.

A LCD manager is in manual update if stallmode is enabled for that manager. TV
managers for now always auto update.

Return the value of stallmode parameter in the private data 'lcd_confg' in
mgr_manual_update() and ovl_manual_update(), for TV managers stallmode field
will be false by default.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 16:27:58 +05:30
Archit Taneja
6e5435958c OMAPDSS: MANAGER: Check LCD related overlay manager parameters
The LCD related manager configurations are a part of the manager's private data
in APPLY. Pass this to dss_lcd_mgr_config to dss_mgr_check and create a function
to check the validity of some of the configurations.

To check some of the configurations, we require information of interface to
which the manager output is connected. These can be added once interfaces are
represented as an entity.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 16:27:57 +05:30
Archit Taneja
f476ae9dab OMAPDSS: APPLY: Remove DISPC writes to manager's lcd parameters in interface drivers
Replace the DISPC fuctions used to configure LCD channel related manager
parameters with dss_mgr_set_lcd_config() in APPLY. This function ensures that
the DISPC registers are written at the right time by using the shadow register
programming model.

The LCD manager configurations is stored as a private data of manager in APPLY.
It is treated as an extra info as it's the panel drivers which trigger this
apply via interface drivers, and not a DSS2 user like omapfb or omapdrm.

Storing LCD manager related properties in APPLY also prevents the need to refer
to the panel connected to the manager for information. This helps in making the
DSS driver less dependent on panel.

A helper function is added to check whether the manager is LCD or TV. The direct
DISPC register writes are removed from the interface drivers.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 16:27:42 +05:30
Archit Taneja
37a579903e OMAPDSS: SDI: Configure dss_lcd_mgr_config struct with lcd manager parameters
Create a dss_lcd_mgr_config struct instance in SDI. Fill up all the parameters
of the struct with configurations held by the panel, and the configurations
required by SDI.

Use these to write to the DISPC registers. These direct register writes would be
later replaced by a function which applies the configuration using the shadow
register programming model.

Create function sdi_config_lcd_manager() which fills the mgr_config parameters
and writes to the DISPC registers.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 16:02:41 +05:30
Archit Taneja
7d2572f8b3 OMAPDSS: DSI: Configure dss_lcd_mgr_config struct with lcd manager parameters
Create a dss_lcd_mgr_config struct instance in DSI. Fill up all the parameters
of the struct with configurations held by the panel, and the configurations
required by DSI.

Use these to write to the DISPC registers. These direct register writes would be
later replaced by a function which applies the configuration using the shadow
register programming model.

The function dsi_configure_dispc_clocks() is now called in
dsi_display_init_dispc(), this lets all the lcd manager related configurations
happen in the same place. The DISPC_DIVISORo register was written in
dsi_configure_dispc_clock(), now it just fills up the dispc_clock_info parameter
in mgr_config. The clock_info is written later in dsi_display_init_dispc().

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 16:02:26 +05:30
Archit Taneja
bc2e60a69f OMAPDSS: RFBI: Configure dss_lcd_mgr_config struct with lcd manager parameters
Create a dss_lcd_mgr_config struct instance in RFBI. Fill up all the parameters
of the struct with configurations held by the panel, and the configurations
required by RFBI.

Use these to write to the DISPC registers. These direct register writes would be
later replaced by a function which applies the configuration using the shadow
register programming model.

Create function rfbi_config_lcd_manager() which fills up the mgr_config
parameters and writes to the DISPC regs.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 14:46:49 +05:30
Archit Taneja
5cf9a26411 OMAPDSS: DPI: Configure dss_lcd_mgr_config struct with lcd manager parameters
Create a dss_lcd_mgr_config struct instance in DPI. Fill up all the parameters
of the struct with configurations held by the panel, and the configurations
required by DPI.

Use these to write to the DISPC registers. These direct register writes would be
later replaced by a function which applies the configuration using the shadow
register programming model.

The DISPC_DIVISORo registers were written in the functions dpi_set_dispc_clk()
and dpi_set_dsi_clk(), now they just fill up the dispc_clock_info parameter in
mgr_config. They are written later in dpi_config_lcd_manager.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 14:46:43 +05:30
David S. Miller
7a9bc9b81a ipv4: Elide fib_validate_source() completely when possible.
If rpfilter is off (or the SKB has an IPSEC path) and there are not
tclassid users, we don't have to do anything at all when
fib_validate_source() is invoked besides setting the itag to zero.

We monitor tclassid uses with a counter (modified only under RTNL and
marked __read_mostly) and we protect the fib_validate_source() real
work with a test against this counter and whether rpfilter is to be
done.

Having a way to know whether we need no tclassid processing or not
also opens the door for future optimized rpfilter algorithms that do
not perform full FIB lookups.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-29 01:36:36 -07:00
Archit Taneja
c56fb3ef05 OMAPDSS: Add struct to hold LCD overlay manager configuration
Create a struct dss_lcd_mgr_config which holds LCD overlay manager related
parameters. These are currently partially contained in the omap_dss_device
connected to the manager, and the rest are in the interface driver.

The parameters are directly written to the DISPC registers in the interface
drivers. These should eventually be applied at the correct time using the
shadow register programming model. This struct would help in grouping these
parameters so that they can be applied together.

Signed-off-by: Archit Taneja <archit@ti.com>
2012-06-29 14:03:48 +05:30