Add ifdef CONFIG_DEBUG_FS guard for emif_debugfs_[init|exit], and adds stub
functions for the case CONFIG_DEBUG_FS is not set.
When CONFIG_DEBUG_FS is enabled, debugfs_create_dir and debugfs_create_file
return NULL on failure, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since 64-bit inodes can be accessed while using inode32, and these can
also be used on 32-bit kernels, there is no reason to still keep inode32
as the default mount option. If the filesystem cannot handle 64bit
inode numbers (i.e CONFIG_LBDAF is not enabled and BITS_PER_LONG == 32),
XFS_MOUNT_SMALL_INUMS will still be set by default, so inode64 is not an
unconditional default value.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
When the separate tda9875 driver was merged into tvaudio the copyright
line of the tda9875 driver was dropped inadvertently. Add it back.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This special driver makes it possible to temporary use NMI debugger port
as a normal console by issuing 'nmi_console' command (assuming that the
port is attached to KGDB).
Unlike KDB's disable_nmi command, with this driver you are always able
to go back to the debugger using KGDB escape sequence ($3#33). This is
because this console driver processes the input in NMI context, and thus
is able to intercept the magic sequence.
Note that since the console interprets input and uses polling
communication methods, for things like PPP it is still better to fully
detach debugger port from the KGDB NMI (i.e. disable_nmi), and use raw
console.
Usually, to enter the debugger one have to type the magic sequence, so
initially the kernel will print the following prompt on the NMI debugger
console:
Type $3#33 to enter the debugger>
For convenience, there is a kgdb_fiq.knock kernel command line option,
when set to 0, this turns the special command to just a return key
press, so the kernel will be printing this:
Hit <return> to enter the debugger>
This is more convenient for long debugging sessions, although it makes
nmi_console feature somewhat useless.
And for the cases when NMI connected to a dedicated button, the knocking
can be disabled altogether by setting kgdb_fiq.knock to -1.
Suggested-by: Colin Cross <ccross@android.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VIDIOC_S_HW_FREQ_SEEK should return EAGAIN when called in non-blocking
mode. This might change in the future if we add support for this in the
future, but right now this is not supported.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to quiesce interrupts in the poll_get_char routine, otherwise,
if used with KGDB NMI debugger, we'll keep reentering the NMI.
Quiescing interrupts is pretty straightforward, except for TXIM
interrupt. The interrupt has "ready to transmit" meaning, so it's
almost always raised, and the only way to silence it is to mask it. But
that's OK, ops->start_tx will unmask it.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The callback is used to initialize the hardware, nothing else should be
done, i.e. we should not request interrupts (but we can and do unmask
some of them, as they might be useful for NMI entry).
As a side-effect, the patch also fixes a division by zero[1] when booting
with kgdboc options specified (e.g. kgdboc=ttyAMA0,115200n8). The issue
happens because serial core calls set_termios callback, but the driver
doesn't know clock frequency, and thus cannot calculate proper baud rate
values.
[1]
WARNING: at drivers/tty/serial/serial_core.c:400 uart_get_baud_rate+0xe8/0x14c()
Modules linked in:
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c0020ae8>] (warn_slowpath_common+0x4c/0x64)
[<c0020ae8>] (warn_slowpath_common+0x4c/0x64) from [<c0020b1c>] (warn_slowpath_null+0x1c/0x24)
[<c0020b1c>] (warn_slowpath_null+0x1c/0x24) from [<c0185ed8>] (uart_get_baud_rate+0xe8/0x14c)
[<c0185ed8>] (uart_get_baud_rate+0xe8/0x14c) from [<c0187078>] (pl011_set_termios+0x48/0x278)
[<c0187078>] (pl011_set_termios+0x48/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
---[ end trace 7d41c9186f342c40 ]---
Division by zero in kernel.
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c014546c>] (Ldiv0+0x8/0x10)
[<c014546c>] (Ldiv0+0x8/0x10) from [<c0187098>] (pl011_set_termios+0x68/0x278)
[<c0187098>] (pl011_set_termios+0x68/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
Division by zero in kernel.
[<c0018e50>] (unwind_backtrace+0x0/0xf0) from [<c014546c>] (Ldiv0+0x8/0x10)
[<c014546c>] (Ldiv0+0x8/0x10) from [<c0183a98>] (uart_update_timeout+0x4c/0x5c)
[<c0183a98>] (uart_update_timeout+0x4c/0x5c) from [<c01870f8>] (pl011_set_termios+0xc8/0x278)
[<c01870f8>] (pl011_set_termios+0xc8/0x278) from [<c01850b0>] (uart_set_options+0xe8/0x114)
[<c01850b0>] (uart_set_options+0xe8/0x114) from [<c0185de4>] (uart_poll_init+0xd4/0xe0)
[<c0185de4>] (uart_poll_init+0xd4/0xe0) from [<c016da8c>] (tty_find_polling_driver+0x100/0x17c)
[<c016da8c>] (tty_find_polling_driver+0x100/0x17c) from [<c0188538>] (configure_kgdboc+0xc8/0x1b8)
[<c0188538>] (configure_kgdboc+0xc8/0x1b8) from [<c00088a4>] (do_one_initcall+0x30/0x168)
[<c00088a4>] (do_one_initcall+0x30/0x168) from [<c033784c>] (do_basic_setup+0x94/0xc8)
[<c033784c>] (do_basic_setup+0x94/0xc8) from [<c03378e0>] (kernel_init+0x60/0xf4)
[<c03378e0>] (kernel_init+0x60/0xf4) from [<c00144a0>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VIDIOC_S_HW_FREQ_SEEK should return EAGAIN when called in non-blocking
mode. This might change in the future if we add support for this in the
future, but right now this is not supported.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge the two entries since they are one and the same error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was noticed that polling drivers (like KGDB) are not able to use
serial ports if the ports were not previously initialized via console.
I.e. when booting with console=ttyAMA0 kgdboc=ttyAMA0, everything works
fine, but with console=ttyFOO kgdboc=ttyAMA0, the kgdboc doesn't work.
This is because we don't initialize the hardware. Calling ->startup() is
not an option, because drivers request interrupts there, and drivers
fail to handle situations when tty isn't opened with interrupts enabled.
So, we have to implement a new callback (actually, tty_ops already have
a similar callback), which does everything needed to initialize just the
hardware.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide module ident information through sysfs.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.if>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'xenarm-for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
arm: introduce a DTS for Xen unprivileged virtual machines
MAINTAINERS: add myself as Xen ARM maintainer
xen/arm: compile netback
xen/arm: compile blkfront and blkback
xen/arm: implement alloc/free_xenballooned_pages with alloc_pages/kfree
xen/arm: receive Xen events on ARM
xen/arm: initialize grant_table on ARM
xen/arm: get privilege status
xen/arm: introduce CONFIG_XEN on ARM
xen: do not compile manage, balloon, pci, acpi, pcpu and cpu_hotplug on ARM
xen/arm: Introduce xen_ulong_t for unsigned long
xen/arm: Xen detection and shared_info page mapping
docs: Xen ARM DT bindings
xen/arm: empty implementation of grant_table arch specific functions
xen/arm: sync_bitops
xen/arm: page.h definitions
xen/arm: hypercalls
arm: initial Xen support
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The format shown on the links internal to the sensor was the first one
enumerated from the sensor, not the highest bit depth data that can be
produced by the sensor. Correct this.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
xfs_ialloc_next_ag() currently resets m_agirotor when it is equal to
m_maxagi:
if (++mp->m_agirotor == mp->m_maxagi)
mp->m_agirotor = 0;
But, if for some reason mp->m_maxagi changes to a lower value than
current m_agirotor, this condition will never be true, causing
m_agirotor to exceed the maximum allowed value (m_maxagi).
This implies mainly during lookups for xfs_perag structs in its radix
tree, since the agno value used for the lookup is based on m_agirotor.
An out-of-range m_agirotor may cause a lookup failure which in case will
return NULL.
As an example, the value of m_maxagi is decreased during
inode64->inode32 remount process, case where I've found this problem.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
smiapp_replace_limit_at() function is not called by the driver.
This was detected by sparse as:
drivers/media/i2c/smiapp/smiapp-quirk.c:64:5: warning:
symbol 'smiapp_replace_limit_at' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the stubs actually usable, since e.g. 'foo = kdb_register();'
leads to build errors in !KGDB_KDB case. Plus, with static inlines we
do type checking.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This command disables NMI-entry. If NMI source has been previously shared
with a serial console ("debug port"), this effectively releases the port
from KDB exclusive use, and makes the console available for normal use.
Of course, NMI can be reenabled, enable_nmi modparam is used for that:
echo 1 > /sys/module/kdb/parameters/enable_nmi
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new arch callback should manage NMIs that usually cause KGDB to
enter. That is, not all NMIs should be enabled/disabled, but only
those that issue kgdb_handle_exception().
We must mask it as serial-line interrupt can be used as an NMI, so
if the original KGDB-entry cause was say a breakpoint, then every
input to KDB console will cause KGDB to reenter, which we don't want.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Actually, there is no reason about why a user must umount and mount a
XFS filesystem to enable 'inode64' option. So, this patch makes this a
remountable option.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
This works around a few glitches in the ST version of the PL011
serial driver when using very high baud rates, as we do in the
Ux500: 3, 3.25, 4 and 4.05 Mbps.
Problem Observed/rootcause:
When using high baud-rates, and the baudrate*8 is getting close to
the provided clock frequency (so a division factor close to 1), when
using bursts of characters (so they are abutted), then it seems as if
there is not enough time to detect the beginning of the start-bit which
is a timing reference for the entire character, and thus the sampling
moment of character bits is moving towards the end of each bit, instead
of the middle.
Fix:
Increase slightly the RX baud rate of the UART above the theoretical
baudrate by 5%. This will definitely give more margin time to the
UART_RX to correctly sample the data at the middle of the bit period.
Also fix the ages old copy-paste error in the very stressed comment,
it's referencing the registers used in the PL010 driver rather than
the PL011 ones.
Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: Matthias Locher <matthias.locher@stericsson.com>
Signed-off-by: Rajanikanth HV <rajanikanth.hv@stericsson.com>
Cc: stable <stable@vger.kernel.org>
Cc: Bibek Basu <bibek.basu@stericsson.com>
Cc: Par-Gunnar Hjalmdahl <par-gunnar.hjalmdahl@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel will handle IXON/IXOFF/IXANY in software if the hardware
doesn't do it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch allows users to use KGDB over serial console on
board based on Samsung SOC. It has been tested on a board using
exynos5.
[dianders: changed poll to return NO_POLL_CHAR, which appears to
fix 'help' in kgdb; also updated commit message]
Signed-off-by: Julien Pichon <pichon.jln@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_* functions are device managed functions and make code a bit
smaller and cleaner.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MAXIDL is the timeout after which a receive buffer is closed when not full if
no more characters are received. We calculate it from the baudrate so that the
duration is always the same at standard rates: about 4ms. At 9600 bauds it gives
a timeout of 4 characters, which is the timeout on the 8250 UART.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
maxidl register was set to fifo size. There is no reason to set this
register to same value as fifo size. Setting it now to 0x10 by default
as in the UCC UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting the fifo to only 1 byte generates one interrupt every 1ms at 9600 bauds.
This is too much. This patch reduces the threshold to speeds below 2400 bauds
like in the 8250 UART driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a desynchronisation problem with CPM UART driver on
Powerpc MPC8xx. The problem happens if data is received before the device
is open by the user application.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently the same card model has two IDs, so this patch
complements the commit 39aced68d6
adding the missing one.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch does the following
- In case of errors if there least one data character in the RX FIFO
read it otherwise it may stall the receiver.
This is recommended in the interrupt reset method in the table 23-246 of
the omap4 TRM.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds driver for Samsung S5K4ECGX image sensor with an
embedded SoC ISP. The driver only implements preview operation mode
and still capture (snapshot) and face detection features are missing
now. Following controls are supported: contrast, saturation,
brightness, sharpness.
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The legacy serial driver will detect the Winbond CIR device as a serial
port, since it looks exactly like a serial port unless you know what
it is from the PNP ID.
Here we track this port as a special PORT_8250_CIR type, preventing the
legacy serial driver from probing it.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We first probe the legacy serial ports and then check pnp. If there
is a non-standard configuration then this might not work, also this
change is needed so we can blacklist Winbond CIR based on PNP ID.
For this to work the 8250_pnp driver must be merged into the 8250
module.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New mem-to-mem video drivers should use V4L2_CAP_VIDEO_M2M capability, rather
than ORed V4L2_CAP_VIDEO_CAPTURE and V4L2_CAP_VIDEO_OUTPUT flags, as outlined
in commit a1367f1b26.
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some minor problems in comments of lis331dlh driver
* correct comments with respect to 2G sensitivity
* correct typo lis3331dlh mistake to lis331dlh
* add comment to say only 2G range is supported
* change the function name from lis3lv02d_read_16 to
lis331dlh_read_data.
* update i2c_device_id table entry to maintaine consistancy
* update sensor display message
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
channel_first_int[][] variable is used as a flag for the ISR,
This flag was being set after enabling the interrupts, There
where situations when the isr occurred even before the flag was set
dues to which it was causing the application hang.
This patch sets channel_first_int[][] flag just before enabling the
interrupt.
Reported-by: David Oleszkiewicz <doleszki@adsyscontrols.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pci_disable_device(pdev) used to be in pci remove function. But this
PCI device has two functions with interrupt lines connected to a
single pin. The other one is a USB host controller. So when we disable
the PIN there e.g. by rmmod hpilo, the controller stops working. It is
because the interrupt link is disabled in ACPI since it is not
refcounted yet. See acpi_pci_link_free_irq called from
acpi_pci_irq_disable.
It is not the best solution whatsoever, but as a workaround until the
ACPI irq link refcounting is sorted out this should fix the reported
errors.
References: https://lkml.org/lkml/2008/11/4/535
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Nobin Mathew <nobin.mathew@gmail.com>
Cc: Robert Hancock <hancockr@shaw.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_tty_get() can return NULL after port hangup that may happen anytime.
The patch adds checks that tty_port_tty_get() returns nonNULL around places
where tty is actually used.
I have no actual hardware to test the patch, so I have updated rx side
processing from common sense only.
v2: rx handling updated according Alan Cox feedback.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes some translation error in Documentation/zh_CN/gpio.txt
The modification is based on Dong Aisheng <b29396@freescale.com>'s
corrections:
1.Two "OUTPUT" is incorrectly translated as "输入";
2.five improvement of translation;
3.Delete a redundant paragraph,
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove 3 byte redundant code at the head of
the Documentation/zh_CN/arm/booting
When I see the file Documentation/zh_CN/arm/booting using
Bless(binary Viewer),I find 3 byte redundant in it. So I
make a patch to correcting that error made by me.
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a Chinese translated version of Documentation/video4linux/omap3isp.txt
Signed-off-by: Fu Wei <tekkamanninja@gmail.com>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some post-3.4 kernels have a problem when a cloned skb is used in the
RX path. This patch handles one such case for r8712u.
The patch was suggested by Eric Dumazet.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a failure in vb2_qbuf in user pointer mode where
__qbuf_userptr checks if the buffer queued by userspace is large
enough. The failure would happen if coda_queue_setup was called
with empty fmt (and thus set the expected buffer size to the maximum
resolution), and userspace queues buffers of smaller size -
corresponding to the negotiated dimensions - were queued.
Explicitly setting sizeimage to the value negotiated via s_fmt
fixes the issue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
