All jobs are failing on Tegra20 because it doesn't use IOMMU and mapping
function uses size of mapping that is zero instead of BO size, fix it.
Fixes: d7c591bc1a ("drm/tegra: Implement new UAPI")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Quoted from [1]
"I do remember that I've added this code back then because otherwise
orphan cleanup was losing updates to quota files. But you're right
that now I don't see how that could be happening and it would be nice
if we could get rid of this hack"
[1] https://lore.kernel.org/linux-ext4/99cce8ca-e4a0-7301-840f-2ace67c551f3@huawei.com/T/#m04990cfbc4f44592421736b504afcc346b2a7c00
Related fix in ext4 by
commit 72ffb49a7b ("ext4: do not set SB_ACTIVE in ext4_orphan_cleanup()").
f2fs has the same hack implementation in
- f2fs_recover_orphan_inodes()
- f2fs_recover_fsync_data()
Let's get rid of this hack as well in f2fs.
Cc: Zhang Yi <yi.zhang@huawei.com>
Cc: Jan Kara <jack@suse.cz>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
As Yi Zhuang reported in bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=214299
There is potential deadlock during quota data flush as below:
Thread A: Thread B:
f2fs_dquot_acquire
down_read(&sbi->quota_sem)
f2fs_write_checkpoint
block_operations
f2fs_look_all
down_write(&sbi->cp_rwsem)
f2fs_quota_write
f2fs_write_begin
__do_map_lock
f2fs_lock_op
down_read(&sbi->cp_rwsem)
__need_flush_qutoa
down_write(&sbi->quota_sem)
This patch changes block_operations() to use trylock, if it fails,
it means there is potential quota data updater, in this condition,
let's flush quota data first and then trylock again to check dirty
status of quota data.
The side effect is: in heavy race condition (e.g. multi quota data
upaters vs quota data flusher), it may decrease the probability of
synchronizing quota data successfully in checkpoint() due to limited
retry time of quota flush.
Reported-by: Yi Zhuang <zhuangyi1@huawei.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For some headsets CS42L42 autodetect mode is not working correctly.
They will be detected as unknown types or as headphones. According
to the CS42L42 datasheet, if the headset autodetect failed,
then the driver should switch to manual mode and perform a manual steps sequence.
These steps were missing in the current driver code. This patch will add manual
mode fallback steps in case autodetect failed. The default behavior is not affected,
manual mode runs only when autodetect failed.
Tested for regression with autodetect with all known headsets - no regression.
Tested with all headsets customers reported as false detected:
Gumdrop DropTech B1 - detected as headset OK
HUAWEI AM115 - detected as headset OK
UGREEN EP103 - detected as headset OK
HONOR AM116 - detected as headset OK
Stefan Binding (1):
ASoC: cs42l42: Implement Manual Type detection as fallback
sound/soc/codecs/cs42l42.c | 104 ++++++++++++++++++++++++++++++++-----
sound/soc/codecs/cs42l42.h | 54 +++++++++++++++++++
2 files changed, 146 insertions(+), 12 deletions(-)
--
2.25.1
Hi,
The probe debug feature of SOF can be used to extract streams of data from a
given point of a pipeline for analysis.
The support is implemented by using the ALSA/ASoC compress support for the
capture stream, but the code can not be used by/for a normal compressed data
stream. It is a debug feature.
Merge the probe implementation in the core (compress.c/h and probe.c/h) into
one file: sof-probes.c/h
Rename the Intel HDA specific probe implementation from hda-compressc.c to
hda-probes.c
We also need to add IPC logging support for the probes messages and drop the
unused references to SOF compress to have reasonably clean code.
Regards,
Peter
---
Peter Ujfalusi (5):
ASoC: SOF: ipc: Add probe message logging to ipc_log_header()
ASoC: SOF: pcm: Remove non existent CONFIG_SND_SOC_SOF_COMPRESS
reference
ASoC: SOF: probe: Merge and clean up the probe and compress files
ASoC: SOF: Intel: Rename hda-compress.c to hda-probes.c
ASoC: SOF: sof-probes: Correct the function names used for
snd_soc_cdai_ops
Ranjani Sridharan (1):
ASoC: SOF: compress: move and export sof_probe_compr_ops
sound/soc/sof/Makefile | 3 +-
sound/soc/sof/compress.c | 147 ---------
sound/soc/sof/compress.h | 32 --
sound/soc/sof/core.c | 2 +-
sound/soc/sof/debug.c | 2 +-
sound/soc/sof/intel/Makefile | 2 +-
sound/soc/sof/intel/hda-dai.c | 16 +-
.../intel/{hda-compress.c => hda-probes.c} | 0
sound/soc/sof/ipc.c | 23 ++
sound/soc/sof/pcm.c | 6 +-
sound/soc/sof/probe.h | 85 ------
sound/soc/sof/sof-priv.h | 5 -
sound/soc/sof/{probe.c => sof-probes.c} | 280 +++++++++++-------
sound/soc/sof/sof-probes.h | 38 +++
14 files changed, 248 insertions(+), 393 deletions(-)
delete mode 100644 sound/soc/sof/compress.c
delete mode 100644 sound/soc/sof/compress.h
rename sound/soc/sof/intel/{hda-compress.c => hda-probes.c} (100%)
delete mode 100644 sound/soc/sof/probe.h
rename sound/soc/sof/{probe.c => sof-probes.c} (52%)
create mode 100644 sound/soc/sof/sof-probes.h
--
2.33.0
We can make code little bit more readable by using min/max macros.
These were found with Coccinelle.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
We can make code little more readable by using kernel macros clamp/max.
This were found with kernel included Coccinelle minmax script.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
We do not need this check as this is same thing as
NTFS_MIN_MFT_ZONE > zlen. We already check NTFS_MIN_MFT_ZONE <= zlen and
exit because is too big request. Remove it so code is cleaner.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
If ntfs_refresh_zone() returns error it will be changed to -ENOSPC. It
is not right. Also caller of this functions also check other errors.
Fixes: 78ab59fee0 ("fs/ntfs3: Rework file operations")
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Remove tabs before spaces from comment as recommended by kernel coding
style. Checkpatch also warn about these.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Remove braces from single statment block as they are not needed. Also
Linux kernel coding style guide recommend this and checkpatch warn about
this.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
For better code readability place constant always right side of the
test. This will also address checkpatch warning.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
No need for plus sign here. So remove it. Checkpatch will also be happy.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
[Why]
The "base_addr_is_mc_addr" field was added for dcn3.1 support but
pa_config was never updated to set it to false.
Uninitialized memory causes it to be set to true which results in
address mistranslation and white screen.
[How]
Use memset to ensure all fields are initialized to 0 by default.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch allows panel orientation quirks from DRM core to be
used. They attach a DRM connector property "panel orientation"
which indicates in which direction the panel has been mounted.
Some machines have the internal screen mounted with a rotation.
Since the panel orientation quirks need the native mode from the
EDID, check for it in amdgpu_dm_connector_ddc_get_modes.
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the user cannot do anything about the unsupported Trusted Memory Zone
(TMZ) feature, do not warn about it, but make it informational, so
demote the log level from warning to info.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was unusual; normally, inline functions are declared static as
well, and defined in a header file if used by multiple compilation
units. The latter would be more involved in this case, so just drop
the inline declaration for now.
Fixes compile failure building for ppc64le on RHEL 8:
In file included from ../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.h:32,
from ../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:33:
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c: In function ‘amdgpu_ras_recovery_init’:
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras_eeprom.h:90:17: error: inlining failed in call
to ‘always_inline’ ‘amdgpu_ras_eeprom_max_record_count’: function body not available
90 | inline uint32_t amdgpu_ras_eeprom_max_record_count(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:1985:34: note: called from here
1985 | max_eeprom_records_len = amdgpu_ras_eeprom_max_record_count();
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c84d46707e "drm/amdgpu: validate bad page threshold in ras(v3)"
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current RUNPM mechanism relies on PMFW to master the timing for BACO
in/exit. And that needs cooperation from sound driver for dstate
change notification for function 1(audio). Otherwise(on sound driver
missing), BACO cannot be kicked in correctly and hang will be observed
on RUNPM exit.
By switching back to legacy message way on sound driver missing,
we are able to fix the runpm hang observed for the scenario below:
amdgpu driver loaded -> runpm suspend kicked -> sound driver loaded
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-and-tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Pass drm dev directly as rdev->ddev gets initialized later on
at radeon_device_init().
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214375
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Separate iommu_resume from kfd_resume, and move it before
other amdgpu ip init/resume.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211277
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Separate kfd_iommu_resume from kfd_resume for fine-tuning
of amdgpu device init/resume/reset/recovery sequence.
v2: squash in fix for !CONFIG_HSA_AMD
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211277
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If link training is aborted, it shall be retried if sink is present.
[How]
Check hpd status to find out whether sink is present or not. If sink is
present, then link training shall be tried again with same settings.
Otherwise, link training shall be aborted.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittently, there presents two occurrences of 0 stream
commits in a single HPD event. Current HDCP sequence does
not consider such scenerio, and will thus disable HDCP.
[How]
Add condition check to include stream remove and re-enable
case for HDCP enable.
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
call stack of amdgpu dsc mst pbn, slot num calculation is as below:
-compute_bpp_x16_from_target_bandwidth
-decide_dsc_target_bpp_x16
-setup_dsc_config
-dc_dsc_compute_bandwidth_range
-compute_mst_dsc_configs_for_link
-compute_mst_dsc_configs_for_state
from pbn -> dsc target bpp_x16
bpp_x16 is calulated by compute_bpp_x16_from_target_bandwidth.
Beside pixel clock and bpp, num_slices_h and bpp_increment_div
will also affect bpp_x16.
from dsc target bpp_x16 -> pbn
within dm_update_mst_vcpi_slots_for_dsc,
pbn = drm_dp_calc_pbn_mode(clock, bpp_x16, true);
drm_dp_calc_pbn_mode(int clock, int bpp, bool dsc)
{
return DIV_ROUND_UP_ULL(mul_u32_u32(clock * (bpp / 16), 64 * 1006),
8 * 54 * 1000 * 1000);
}
bpp / 16 trunc digits after decimal point. This will cause calculation
delta. drm_dp_calc_pbn_mode does not have other informations,
like num_slices_h, bpp_increment_div. therefore, it does not do revese
calcuation properly from bpp_x16 to pbn.
pbn from drm_dp_calc_pbn_mode is less than pbn from
compute_mst_dsc_configs_for_state. This cause not enough mst slot
allocated to display. display could not visually light up.
[How]
pass pbn from compute_mst_dsc_configs_for_state to
dm_update_mst_vcpi_slots_for_dsc
Cc: stable@vger.kernel.org
Reviewed-by: Scott Foster <Scott.Foster@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On Carrizo/Stoney systems we set backlight through panel_cntl, i.e.
directly via the PWM registers, if DMCU is not initialized. We
always read it back through ABM registers which leads to a
mismatch and forces atomic_commit to program the backlight
each time.
Instead make sure we use the same logic for backlight readback,
i.e. read it from panel_cntl if DMCU is not initialized.
We also need to remove some extraneous and incorrect calculations
at the end of dce_get_16_bit_backlight_from_pwm.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1666
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On some GPUs the PCIe atomic requirement for KFD depends on the MEC
firmware version. Add a firmware version check for this. The minimum
firmware version that works without atomics can be updated in the
device_info structure for each GPU type.
Move PCIe atomic detection from kgd2kfd_probe into kgd2kfd_device_init
because the MEC firmware is not loaded yet at the probe stage.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add manual sclk/vddc setting supoort via pp_od_clk_voltage sysfs
to maintain consistency with other asics. As cyan skillfish doesn't
support DPM, there is only a single frequency and voltage to adjust.
v2: maintain consistency and add command guide.
v3: adjust user settings storage and coding style.
Command guide:
echo vc point sclk vddc > pp_od_clk_voltage
"vc" - sclk voltage curve
"point" - must be 0
"sclk" - target value of sclk(MHz), should be in safe range
"vddc" - target value of vddc(mV), a 6.25(mV) stepping is
recommended and should be in safe range (the real
vddc is an approximation of target value)
echo c > pp_od_clk_voltage
"c" - commit the changes of sclk and vddc, only after
the commit command, the target values set by "vc"
command will take effect
echo r > pp_od_clk_voltage
"r" - reset sclk and vddc to default value, a subsequent
commit command is needed to take effect
Example:
1) Check default sclk and vddc
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 862mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
2) Set sclk to 1500MHz and vddc to 700mV
$ echo vc 0 1500 700 > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1500Mhz *
OD_VDDC:
0: 693mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
3) Reset sclk and vddc to default
$ echo r > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 874mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
NOTE:
We don't specify an explicit safe range, you can set any values
between min and max at your own risk. Enjoy!
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add print_clk_levels and read_sensor pptable funcs for
cyan skilfish.
v2: keep consitency and add get_gpu_metrics callback.
v3: use sysfs_emit_at() in sysfs show function.
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add SmuMetrics_t definition for cyan skilfish.
v2: update SmuMetrics_t definition.
v3: cleanup and rearrange the order of fields.
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some PPSMC MSGs for cyan skilfish.
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Assert only when FPU is not enabled.
Fixes: 0ea7ee8217 ("drm/amd/display: Add DC_FP helper to check FPU state")
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we're running a headless config with 0 links then the vblank
workqueue will be NULL - causing a NULL pointer exception during
any commit.
[How]
Guard access to the workqueue if it's NULL and don't queue or flush
work if it is.
Reported-by: Mike Lothian <mike@fireburn.co.uk>
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1700
Fixes: 58aa1c50e5 ("drm/amd/display: Use vblank control events for PSR enable/disable")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch enables HDMI display on PINE64 PineTab.
The PineTab has a HDMI Type C (mini) port.
Signed-off-by: Dang Huynh <danct12@disroot.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210914193732.3047668-1-danct12@disroot.org
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916105633.12162-1-caihuoqing@baidu.com
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916105625.12109-1-caihuoqing@baidu.com
On OcteonTX2/CN10K SoC, the admin function (AF) is the only one
with all priviliges to configure HW and alloc resources, PFs and
it's VFs have to request AF via mailbox for all their needs.
This patch adds new mailbox messages for CPT PFs and VFs to configure
HW resources for inline-IPsec.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Vidya Sagar Velumuri <vvelumuri@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RFC8998 specification defines the use of the ShangMi algorithm
cipher suites in TLS 1.3, and also supports the GCM/CCM mode using
the SM4 algorithm.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink parameters are not the right mechanism to pass
extra parameters to device flashing. The params added are
also undocumented.
This reverts commit 13bb8429ca ("net: wwan: iosm: firmware
flashing and coredump collection").
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network interface managed by the mlxbf_gige driver can
get into a problem state where traffic does not flow.
In this state, the interface will be up and enabled, but
will stop processing received packets. This problem state
will happen if three specific conditions occur:
1) driver has received more than (N * RxRingSize) packets but
less than (N+1 * RxRingSize) packets, where N is an odd number
Note: the command "ethtool -g <interface>" will display the
current receive ring size, which currently defaults to 128
2) the driver's interface was disabled via "ifconfig oob_net0 down"
during the window described in #1.
3) the driver's interface is re-enabled via "ifconfig oob_net0 up"
This patch ensures that the driver's "valid_polarity" field is
cleared during the open() method so that it always matches the
receive polarity used by hardware. Without this fix, the driver
needs to be unloaded and reloaded to correct this problem state.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K MAC block (RPM) differs in number of stats compared to Octeontx2
MAC block (CGX). RPM supports stats for each class of PFC and error
packets etc. It would be difficult for user to read stats from ethtool
and map to their definition.
New debugfs file is already added to read RPM stats along with their
definition. This patch adds proper checks such that RPM stats will not
be part of ethtool.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we implement delayed destroy, we may have a second
call to the delete_mem_notify() handler, while free_object()
only should be called once.
Move it to bo->destroy(), to ensure it's only called once.
This fixes some weird memory corruption issues with delayed
destroy when async eviction is used.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210830121006.2978297-2-maarten.lankhorst@linux.intel.com
Fixes: 213d509277 ("drm/i915/ttm: Introduce a TTM i915 gem object backend")
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Checking tunnel offloading, it turns out that offloading doesn't work
as expected. The following script allows to reproduce the issue.
Call it as `testscript DEVICE LOCALIP REMOTEIP NETMASK'
=== SNIP ===
if [ $# -ne 4 ]
then
echo "Usage $0 DEVICE LOCALIP REMOTEIP NETMASK"
exit 1
fi
DEVICE="$1"
LOCAL_ADDRESS="$2"
REMOTE_ADDRESS="$3"
NWMASK="$4"
echo "Driver: $(ethtool -i ${DEVICE} | awk '/^driver:/{print $2}') "
ethtool -k "${DEVICE}" | grep tx-udp
echo
echo "Set up NIC and tunnel..."
ip addr add "${LOCAL_ADDRESS}/${NWMASK}" dev "${DEVICE}"
ip link set "${DEVICE}" up
sleep 2
ip link add vxlan1 type vxlan id 42 \
remote "${REMOTE_ADDRESS}" \
local "${LOCAL_ADDRESS}" \
dstport 0 \
dev "${DEVICE}"
ip addr add fc00::1/64 dev vxlan1
ip link set vxlan1 up
sleep 2
rm -f vxlan.pcap
echo "Running tcpdump and iperf3..."
( nohup tcpdump -i any -w vxlan.pcap >/dev/null 2>&1 ) &
sleep 2
iperf3 -c fc00::2 >/dev/null
pkill tcpdump
echo
echo -n "Max. Paket Size: "
tcpdump -r vxlan.pcap -nnle 2>/dev/null \
| grep "${LOCAL_ADDRESS}.*> ${REMOTE_ADDRESS}.*OTV" \
| awk '{print $8}' | awk -F ':' '{print $1}' \
| sort -n | tail -1
echo
ip link del vxlan1
ip addr del ${LOCAL_ADDRESS}/${NWMASK} dev "${DEVICE}"
=== SNAP ===
The expected outcome is
Max. Paket Size: 64904
This is what you see on igb, the code igc has been taken from.
However, on igc the output is
Max. Paket Size: 1516
so the GSO aggregate packets are segmented by the kernel before calling
igc_xmit_frame. Inside the subsequent call to igc_tso, the check for
skb_is_gso(skb) fails and the function returns prematurely.
It turns out that this occurs because the feature flags aren't set
entirely correctly in igc_probe. In contrast to the original code
from igb_probe, igc_probe neglects to set the flags required to allow
tunnel offloading.
Setting the same flags as igb fixes the issue on igc.
Fixes: 34428dff36 ("igc: Add GSO partial support")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IdleMask is the metric used by the PM firmware to know the status of each
of the Hardware IP blocks monitored by the PM firmware.
Knowing this value is key to get the information of s2idle suspend/resume
status. This value is mapped to PMC scratch registers, retrieve them
accordingly based on the CPU family and the underlying firmware support.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20210916124002.2529-1-Sanket.Goswami@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
As the PM firmware returns the status of the last s0i3 in the smu_metrics
structure, the existing name "s0i3_cyclecount" seems to be a misnomer.
Change it accordingly to "s0i3_last_entry_status".
Signed-off-by: Sanket Goswami <Sanket.Goswami@amd.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20210916124130.2581-1-Sanket.Goswami@amd.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>