It turns out that DE3 manual has inverted YUV and YVU format numbers for
P010 and P210. Invert them.
This was tested by playing video decoded to P010 and additionally
confirmed by looking at BSP driver source.
Fixes: 169ca4b389 ("drm/sun4i: Add separate DE3 VI layer formats")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228181436.1424550-1-jernej.skrabec@gmail.com
Use devm_add_action_or_reset() instead of devm_add_action()+hand writing
what is done in the release function, should an error occur.
This is more straightforward and saves a few lines of code.
While at it, remove a useless test in devm_backlight_release(). 'data' is
known to be not NULL when this function is called.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/f998a4291d865273afa0d1f85764a9ac7fbc1b64.1644738084.git.christophe.jaillet@wanadoo.fr
Drop several includes of <linux/personality.h> which are not used.
git-blame indicates they were used at some point, but they're not needed
anymore.
Signed-off-by: Sagar Patel <sagarmp@cs.unc.edu>
Link: https://lore.kernel.org/r/20220307222412.146506-1-sagarmp@cs.unc.edu
Signed-off-by: Will Deacon <will@kernel.org>
The following patches resulted in deferring crash kernel reservation to
mem_init(), mainly aimed at platforms with DMA memory zones (no IOMMU),
in particular Raspberry Pi 4.
commit 1a8e1cef76 ("arm64: use both ZONE_DMA and ZONE_DMA32")
commit 8424ecdde7 ("arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges")
commit 0a30c53573 ("arm64: mm: Move reserve_crashkernel() into mem_init()")
commit 2687275a58 ("arm64: Force NO_BLOCK_MAPPINGS if crashkernel reservation is required")
Above changes introduced boot slowdown due to linear map creation for
all the memory banks with NO_BLOCK_MAPPINGS, see discussion[1]. The proposed
changes restore crash kernel reservation to earlier behavior thus avoids
slow boot, particularly for platforms with IOMMU (no DMA memory zones).
Tested changes to confirm no ~150ms boot slowdown on our SoC with IOMMU
and 8GB memory. Also tested with ZONE_DMA and/or ZONE_DMA32 configs to confirm
no regression to deferring scheme of crash kernel memory reservation.
In both cases successfully collected kernel crash dump.
[1] https://lore.kernel.org/all/9436d033-579b-55fa-9b00-6f4b661c2dd7@linux.microsoft.com/
Signed-off-by: Vijay Balakrishna <vijayb@linux.microsoft.com>
Cc: stable@vger.kernel.org
Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/r/1646242689-20744-1-git-send-email-vijayb@linux.microsoft.com
[will: Add #ifdef CONFIG_KEXEC_CORE guards to fix 'crashk_res' references in allnoconfig build]
Signed-off-by: Will Deacon <will@kernel.org>
In this situation (VLAN filtering disabled on br0):
br0.10
/
br0
/ \
swp0 swp1
When a frame is transmitted from the VLAN upper, the bridge will send
it down to one of the switch ports with forward offloading
enabled. This will cause tag_dsa to generate a FORWARD tag. Before
this change, that tag would have it's VID set to 10, even though VID
10 is not loaded in the VTU.
Before the blamed commit, the frame would trigger a VTU miss and be
forwarded according to the PVT configuration. Now that all fabric
ports are in 802.1Q secure mode, the frame is dropped instead.
Therefore, restrict the condition under which we rewrite an 802.1Q tag
to a DSA tag. On standalone port's, reuse is always safe since we will
always generate FROM_CPU tags in that case. For bridged ports though,
we must ensure that VLAN filtering is enabled, which in turn
guarantees that the VID in question is loaded into the VTU.
Fixes: d352b20f41 ("net: dsa: mv88e6xxx: Improve multichip isolation of standalone ports")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220307110548.812455-1-tobias@waldekranz.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 18107f8a2d ("arm64: Support execute-only permissions with
Enhanced PAN") re-introduced execute-only permissions when EPAN is
available. When EPAN is not available, arch_filter_pgprot() is supposed
to change a PAGE_EXECONLY permission into PAGE_READONLY_EXEC. However,
if BTI or MTE are present, such check does not detect the execute-only
pgprot in the presence of PTE_GP (BTI) or MT_NORMAL_TAGGED (MTE),
allowing the user to request PROT_EXEC with PROT_BTI or PROT_MTE.
Remove the arch_filter_pgprot() function, change the default VM_EXEC
permissions to PAGE_READONLY_EXEC and update the protection_map[] array
at core_initcall() if EPAN is detected.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 18107f8a2d ("arm64: Support execute-only permissions with Enhanced PAN")
Cc: <stable@vger.kernel.org> # 5.13.x
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
In case the MAC is using 'netif_rx()' to deliver the skb up the network
stack, it needs to check whether 'skb_defer_rx_timestmap()' is necessary
or not. In case is needed then don't call 'netif_rx()'
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220307094632.3764266-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
syscon regmap is not used since commit addebf1588 ("mfd: exynos-lpass:
Remove pad retention control").
Fixes: addebf1588 ("mfd: exynos-lpass: Remove pad retention control")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220202151310.285561-3-krzysztof.kozlowski@canonical.com
This debugfs isn't used by anyone, if we want to dump the contents
of registers we should just convert the driver to regmap instead.
I'm also excluding this from the device tree bindings when converting
to YAML because it is not a real device, and device trees should
only contain real physical devices.
Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220212214724.681530-1-linus.walleij@linaro.org
pci_driver probe functions aren't called with locks held and
thus don't need GFP_ATOMIC. Use GFP_KERNEL instead.
Problem found with Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220210204223.104181-10-Julia.Lawall@inria.fr
This rewrites the former text based AB8500 bindings in YAML.
When the AB8500 bindings were first written (in 2012) we
were not strict on some things and node names were definitely
not standardized.
This patch uses standard node names to most of the subnodes
on the AB8500 and is accompanied by another patch fixing
all the DTS files to conform to this.
The bindings are not as perfect as newly written bindings
would be, it is a best effort to deal with the legacy.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220115002649.1526163-1-linus.walleij@linaro.org
Document the compatible for pm8953 as found in msm8953.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220112194118.178026-5-luca@z3ntu.xyz
Returning a non-zero value in an i2c remove callback results in the i2c
core emitting a very generic error message ("remove failed (-ESOMETHING),
will be ignored") and as the message indicates not further error handling
is done.
Instead emit a more specific error message and then return zero in
.remove().
The long-term goal is to make the i2c remove prototype return void, making
all implementations return 0 is preparatory work for this change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220214150710.312269-1-u.kleine-koenig@pengutronix.de
Document the compatible for tcsr found in msm8953.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220112194118.178026-4-luca@z3ntu.xyz
This adds reboot support to the rk808 pmic driver and enables it for
the rk809 and rk817 devices.
This only enables if the rockchip,system-power-controller flag is set.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220208194023.929720-1-pgwipeout@gmail.com
Documentation/hwmon/sy7636a-hwmon.rst:4: WARNING: Title underline too short.
Kernel driver sy7636a-hwmon
=========================
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/all/YgTRu7iLgJMymeT5@google.com/
When the match tables were split for I2C and SPI a static should have
been added since the tables are no longer exported.
Fixes: 3f65555c41 ("mfd: arizona: Split of_match table into I2C and SPI versions")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220104165435.26782-1-ckeepax@opensource.cirrus.com
The config DBX500_PRCMU_QOS_POWER was never introduced in the kernel
repository. So, the ifdef in ./include/linux/mfd/dbx500-prcmu.h was never
effective.
Remove these dead function prototypes.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211227064839.21405-1-lukas.bulwahn@gmail.com
For the CRC PMIC we end up with multiple IRQ domains with the same fwnode.
One for the irqchip which demultiplexes the actual PMIC interrupt into
interrupts for the various cells (known as the level 1 interrupts);
And 2 more for the irqchips which are part of the crystal_cove_gpio
and crystal_cove_charger cells.
This leads to the following error being printed when
CONFIG_GENERIC_IRQ_DEBUGFS is enabled:
debugfs: File '\_SB.I2C7.PMIC' in directory 'domains' already present!
Set the bus token of the main IRQ domain to DOMAIN_BUS_NEXUS to avoid
this error, this also allows irq_find_matching_fwspec() to find the
right domain if necessary.
Note all 3 domain registering drivers need to set the IRQ domain bus token.
This is necessary because the IRQ domain code defaults to creating
the debugfs dir with just the fwnode name and then renames it when
the bus token is set. So each one starts with the same default name and
all 3 must be given a different name to avoid problems when one of the
other drivers loads and starts with the same default name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211225115509.94891-4-hdegoede@redhat.com
The Crystal Cove PMIC has a pin which can be used to connect the IRQ of
an external charger IC. On some boards this is used and we need to have
a cell for this, with a driver which creates its own irqchip with
a single IRQ for the charger driver to consume.
The charger driver cannot directly consume the IRQ from the MFD level
irqchip because the PMIC has 2 levels of interrupts and the second
level interrupt status register, which is handled by the cell drivers,
needs to have the IRQ acked to avoid an IRQ storm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211225115509.94891-3-hdegoede@redhat.com
The cells for the Crystal Cove PMIC are already mostly sorted by
function / IRQ order. Move the ADC cell so that they are fully sorted.
Also move some of the resource definitions so that their order matches
the (new) order of the cells.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211225115509.94891-2-hdegoede@redhat.com
In case of DT-configured systems it may be hard to identify the PHY
interrupt in the /proc/interrupts output. Therefore add the name to
the id to make clearer that it's about a device on a muxed mdio bus.
In my case:
Now: mdio_mux-0.e40908ff:08
Before: 0.e40908ff:08
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/00b4bb1e-98f9-b4e7-5549-e095a4701f66@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Focusrite Scarlett Gen 2/3 interfaces with internal mixers have a
"standalone" mode. When the interface is not connected to a USB host
and standalone mode is enabled, the interface will pass audio as
previously configured. This patch adds an ALSA control to allow
enabling/disabling that mode.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/cd88871c5e77abd5c23a4758a1f2ec9fd427fd69.1646578164.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
scarlett2_config_items[] contains the parameters for the configuration
items. The driver previously had two sets of configurations items; one
for devices with no mixer, and one for devices with a mixer. This
patch splits the latter into two (one set for Gen 2 devices and one
set for Gen 3 devices) in preparation for a new item (standalone)
which is present in both but with a different offset.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20969f9ea500684e978c87067fbdc7e73de1f6ed.1646578164.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the following coccicheck warning:
./drivers/gpu/drm/omapdrm/omap_overlay.c:89:22-25: ERROR: r_ovl is NULL
but dereferenced.
Here should be ovl->idx rather than r_ovl->idx.
Fixes: e02b5cc9e8 ("drm/omap: Add a 'right overlay' to plane state")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220307095612.409090-1-wanjiabing@vivo.com
Use list_first_entry()/list_last_entry() instead of open coded variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Compiler is not happy:
warning: symbol 'gpio_sim_hog_config_item_ops' was not declared. Should it be static?
Fixes: cb8c474e79 ("gpio: sim: new testing module")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Even if SPI_NOR_NO_ERASE was set, one could still send erase opcodes
to the flash. It is not recommended to send unsupported opcodes to
flashes. Fix the logic and do not set mtd->_erase when SPI_NOR_NO_ERASE
is specified. With this users will not be able to issue erase opcodes to
flashes and instead they will recive an -ENOTSUPP error.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220228163334.277730-1-tudor.ambarus@microchip.com
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worse scenario, could lead to heap overflows.
Also, address the following sparse warning:
drivers/char/tpm/xen-tpmfront.c:131:16: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/160
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The X.509 parser always sets cert->sig->pkey_algo and
cert->sig->hash_algo on success, since x509_note_sig_algo() is a
mandatory action in the X.509 ASN.1 grammar, and it returns an error if
the signature's algorithm is unknown. Thus, remove the dead code which
handled these fields being NULL.
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The X.509 parser always sets cert->pub->pkey_algo on success, since
x509_extract_key_data() is a mandatory action in the X.509 ASN.1
grammar, and it returns an error if the algorithm is unknown. Thus,
remove the dead code which handled this field being NULL. This results
in the ->unsupported_key flag never being set, so remove that too.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Remove unused fields from struct x509_parse_context.
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
An X.509 certificate has two, potentially different public key
algorithms: the one used by the certificate's key, and the one that was
used to sign the certificate. Some of the naming made it unclear which
algorithm was meant. Rename things appropriately:
- x509_note_pkey_algo() => x509_note_sig_algo()
- algo_oid => sig_algo
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
In many cases, keyctl_pkey_params_get_2() is validating the user buffer
lengths against the wrong algorithm properties. Fix it to check against
the correct properties.
Probably this wasn't noticed before because for all asymmetric keys of
the "public_key" subtype, max_data_size == max_sig_size == max_enc_size
== max_dec_size. However, this isn't necessarily true for the
"asym_tpm" subtype (it should be, but it's not strictly validated). Of
course, future key types could have different values as well.
Fixes: 00d60fd3b9 ("KEYS: Provide keyctls to drive the new key type ops for asymmetric keys [ver #2]")
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Add a test for /dev/tpmrm0 in async mode that checks if
the code handles invalid handles correctly.
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <linux-integrity@vger.kernel.org>
Cc: <linux-kselftest@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Tested-by: Jarkko Sakkinen<jarkko@kernel.org>
Signed-off-by: Tadeusz Struk <tstruk@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
When an invalid (non existing) handle is used in a TPM command,
that uses the resource manager interface (/dev/tpmrm0) the resource
manager tries to load it from its internal cache, but fails and
the tpm_dev_transmit returns an -EINVAL error to the caller.
The existing async handler doesn't handle these error cases
currently and the condition in the poll handler never returns
mask with EPOLLIN set.
The result is that the poll call blocks and the application gets stuck
until the user_read_timer wakes it up after 120 sec.
Change the tpm_dev_async_work function to handle error conditions
returned from tpm_dev_transmit they are also reflected in the poll mask
and a correct error code could passed back to the caller.
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: <linux-integrity@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Fixes: 9e1b74a63f ("tpm: add support for nonblocking operation")
Tested-by: Jarkko Sakkinen<jarkko@kernel.org>
Signed-off-by: Tadeusz Struk <tstruk@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Determine an available PCR bank to be used by a test case by querying the
capability TPM2_GET_CAP. The TPM2 returns TPML_PCR_SELECTIONS that
contains an array of TPMS_PCR_SELECTIONs indicating available PCR banks
and the bitmasks that show which PCRs are enabled in each bank. Collect
the data in a dictionary. From the dictionary determine the PCR bank that
has the PCRs enabled that the test needs. This avoids test failures with
TPM2's that either to not have a SHA-1 bank or whose SHA-1 bank is
disabled.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Variable etype is being assigned a value that is never read. The
variable and assignment are redundant and can be removed.
Cleans up clang scan build warning:
fs/udf/super.c:2485:10: warning: Although the value stored to 'etype'
is used in the enclosing expression, the value is never actually read
from 'etype' [deadcode.DeadStores]
Link: https://lore.kernel.org/r/20220307152149.139045-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The current implementation of the async flip wm0/ddb optimization
does not work at all. The biggest problem is that we skip the
whole intel_pipe_update_{start,end}() dance and thus never actually
complete the commit that is trying to do the wm/ddb change.
To fix this we need to move the do_async_flip flag to the crtc
state since we handle commits per-pipe, not per-plane.
Also since all planes can now be included in the first/last
"async flip" (which gets converted to a sync flip to do the
wm/ddb mangling) we need to be more careful when checking if
the plane state is async flip comptatible. Only planes doing
the async flip should be checked and other planes are perfectly
fine not adhereing to any async flip related limitations.
However for subsequent commits which are actually going do the
async flip in hardware we want to make sure no other planes
are in the state. That should never happen assuming we did our
job correctly, so we'll toss in a WARN to make sure we catch
any bugs here.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: c3639f3be4 ("drm/i915: Use wm0 only during async flips for DG2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 2e08437160)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since the async flip state check is done very late and
thus it can see potentially all the planes in the state
(due to the wm/ddb optimization) we need to move the
"can the requested plane do async flips at all?" check
much earlier. For this purpose we introduce
intel_async_flip_check_uapi() that gets called early during
the atomic check.
And for good measure we'll throw in a couple of basic checks:
- is the crtc active?
- was a modeset flagged?
- is+was the plane enabled?
Though atm all of those should be guaranteed by the fact
that the async flip can only be requested through the legacy
page flip ioctl.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: c3639f3be4 ("drm/i915: Use wm0 only during async flips for DG2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit b0b2bed2a1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
data_rate==0 no longer means a plane is disabled, it could
also mean we want to use the minimum ddb allocation for it.
Hence we can't bail out early during ddb allocation or
else we'll simply forget to allocate any ddb for such planes.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 6a4d8cc6bb ("drm/i915: Don't allocate extra ddb during async flip for DG2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 6475e10682)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
bigjoiner_pipes==0 leads bigjoiner_master_pipe() to
do BIT(ffs(0)-1) which is undefined behaviour. The code should
actually still work fine since the only place we provoke
that is intel_crtc_bigjoiner_slave_pipes() and it'll bitwise
AND the result with 0, so doesn't really matter what we get
out of bigjoiner_master_pipe(). But best not provoke undefined
behaviour anyway.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: a6e7a006f5 ("drm/i915: Change bigjoiner state tracking to use the pipe bitmask")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
(cherry picked from commit cccc71b552)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
