"make dtbs_check" reports:
arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dt.yaml: soc: refclk: {'compatible': ['fixed-clock'], '#clock-cells': [[0]], 'clock-frequency': [[600000000]], 'clock-output-names': ['msspllclk'], 'phandle': [[7]]} should not be valid under {'type': 'object'}
From schema: dtschema/schemas/simple-bus.yaml
Fix this by moving the node out of the "soc" subnode.
While at it, rename it to "msspllclk", and drop the now superfluous
"clock-output-names" property.
Move the actual clock-frequency value to the board DTS, since it is not
set until bitstream programming time.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
It does not make sense to have an (empty) chosen node in an SoC-specific
.dtsi, as chosen is meant for system-specific configuration.
It is already provided in microchip-mpfs-icicle-kit.dts anyway.
Fixes: 0fa6107eca ("RISC-V: Initial DTS for Microchip ICICLE board")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped.
Fix this by grouping the tuples of "interrupts" and
"interrupts-extended" properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
"make dtbs_check":
arch/riscv/boot/dts/canaan/sipeed_maix_bit.dt.yaml: spi-flash@0: $nodename:0: 'spi-flash@0' does not match '^flash(@.*)?$'
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
Fix this by renaming all SPI FLASH nodes to "flash".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Move the 'inline' keyword to the front of 'void'.
Remove a warning found by clang(make W=1 LLVM=1)
./include/linux/blk-mq.h:259:1: warning: ‘inline’ is not at beginning of
declaration
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220107005228.103927-1-yang.lee@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmHZ88MTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqcnaB/97JfjxMSW3j2TpWCwDMu/pXfsiZIn3
qAiuJ9xAtTeQVCXZxIhMctsBDuNszV59ofdO3l9eb2r0pIzxXH1IIqgkqw5BIeVb
d3PrNINqeD0fn+q0uXk92/CU6iGIYWFB+sF2Dd4OgiRlWAENL6KZNb/DP2uURp4D
HXwgWjC06EZIQ7ul3YFXeUc+uI8QAtQdwunbWZdzU4I77IiqFjsnaFVMsTXzgQpo
9JUNfvmrNDxQ1LYNcsC/+qwu76g3101CTHh8X6QQhd/6oo1PY0nWFnEzNBZX72Te
TMVKadwqgCMuXC7gE6YCZc7sLhmuw6LnC/SMkwl02MGVUdlOG/Vx6NBF
=srEo
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.17-20220108' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-01-08
this is a pull request of 22 patches for net-next/master.
The first patch is by Tom Rix and fixes an uninitialized variable in
the janz-ican3 driver (introduced in linux-can-next-for-5.17-20220105).
The next 13 patches are by my and target the mcp251xfd driver. First
several cleanup patches, then the driver is prepared for the upcoming
ethtool ring parameter and IRQ coalescing support, which is added in a
later pull request.
The remaining 8 patches are by Dario Binacchi and me and enhance the
flexcan driver. The driver is moved into a sub directory. An ethtool
private flag is added to optionally disable CAN RTR frame reception,
to make use of more RX buffers. The resulting RX buffer configuration
can be read by ethtool ring parameter support. Finally documentation
for the ethtool private flag is added to the
Documentation/networking/device_drivers/can directory.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tctx_task_work() may get run after io_uring cancellation and so there
will be no one to put cached in tctx task refs that may have been added
back by tw handlers using inline completion infra, Call
io_uring_drop_tctx_refs() at the end of the main tw handler to release
them.
Cc: stable@vger.kernel.org # 5.15+
Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Fixes: e98e49b2bb ("io_uring: extend task put optimisations")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/69f226b35fbdb996ab799a8bbc1c06bf634ccec1.1641688805.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix the following build issues:
mips64el-linux-ld: arch/mips/boot/compressed/decompress.o: in function `FSE_buildDTable_internal':
decompress.c:(.text.FSE_buildDTable_internal+0x2cc): undefined reference to `__clzdi2'
mips64el-linux-ld: arch/mips/boot/compressed/decompress.o: in function `BIT_initDStream':
decompress.c:(.text.BIT_initDStream+0x7c): undefined reference to `__clzdi2'
mips64el-linux-ld: decompress.c:(.text.BIT_initDStream+0x158): undefined reference to `__clzdi2'
mips64el-linux-ld: arch/mips/boot/compressed/decompress.o: in function `ZSTD_buildFSETable_body_default.constprop.0':
decompress.c:(.text.ZSTD_buildFSETable_body_default.constprop.0+0x2a8): undefined reference to `__clzdi2'
mips64el-linux-ld: arch/mips/boot/compressed/decompress.o: in function `FSE_readNCount_body_default':
decompress.c:(.text.FSE_readNCount_body_default+0x130): undefined reference to `__ctzdi2'
mips64el-linux-ld: decompress.c:(.text.FSE_readNCount_body_default+0x1a4): undefined reference to `__ctzdi2'
mips64el-linux-ld: decompress.c:(.text.FSE_readNCount_body_default+0x2e4): undefined reference to `__clzdi2'
mips64el-linux-ld: arch/mips/boot/compressed/decompress.o: in function `HUF_readStats_body_default':
decompress.c:(.text.HUF_readStats_body_default+0x184): undefined reference to `__clzdi2'
mips64el-linux-ld: decompress.c:(.text.HUF_readStats_body_default+0x1b4): undefined reference to `__clzdi2'
mips64el-linux-ld: arch/mips/boot/compressed/decompress.o: in function `ZSTD_DCtx_getParameter':
decompress.c:(.text.ZSTD_DCtx_getParameter+0x60): undefined reference to `__clzdi2'
Fixes: a510b61613 ("MIPS: Add support for ZSTD-compressed kernels")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Nick Terrell <terrelln@fb.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the Netgear WN2500 RP v1 and v2 Wi-Fi range extenders
based on the BCM5357 chipset and supporting 802.11n and 802.11ac.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add support for the Netgear R6300 v1 Wi-Fi router using a Broadcom
BCM4706 chipset and supporting 802.11n and 802.11ac.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the definitions for the buttons and LEDs used on the Asus RTN-10U
router.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This router is based on a Broadcom BCM4717A1 chipset and supports
802.11n Wi-Fi. Add a board entry for that router and register LEDs and
buttons accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Update the buttons registration code to register the two buttons (WPS,
system rester) using the existing BCM47XX_BOARD_LINKSYS_WRT310NV2 board
entry.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix following includecheck warning:
./arch/mips/include/asm/local.h: asm/asm.h is included more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220106002952.25883-1-brian.silverman@bluerivertech.com
Link: https://github.com/candle-usb/candleLight_fw/issues/87
Cc: stable@vger.kernel.org
Signed-off-by: Brian Silverman <brian.silverman@bluerivertech.com>
[mkl: initialize the reserved member, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure we free CAN network device in the error path. There are
several jumps to fail label after allocating the CAN network device
successfully. This patch places the free_candev() under fail label so
that in failure path a jump to fail label frees the CAN network
device.
Fixes: 76e9353a80 ("can: rcar_canfd: Add support for RZ/G2L family")
Link: https://lore.kernel.org/all/20220106114801.20563-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Link: https://lore.kernel.org/all/20211224021324.1447494-1-jiasheng@iscas.ac.cn
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Link: https://lore.kernel.org/all/20220109103126.1872833-1-mkl@pengutronix.de
Fixes: 03fd3cf5a1 ("can: add driver for Softing card")
Cc: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CS35L41 SPI and I2C drivers depend on those buses, hence they have to
have dependencies in Kconfig; otherwise it may result in missing
symbols.
Fixes: 7b2f3eb492 ("ALSA: hda: cs35l41: Add support for CS35L41 in HDA systems")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220109081337.30623-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Zinitix BT532 is another touch controller that seem to implement the
same interface as an already supported BT541. Add it to the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-5-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The supply names of the Zinitix touchscreen were a bit confused, the new
bindings rectifies this.
To deal with old and new devicetrees, first check if we have "vddo" and in
case that exists assume the old supply names. Else go and look for the new
ones.
We cannot just get the regulators since we would get an OK and a dummy
regulator: we need to check explicitly for the old supply name.
Use struct device *dev as a local variable instead of the I2C client since
the device is what we are actually obtaining the resources from.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Slightly changed the legacy regulator detection]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-4-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This converts the Zinitix BT4xx and BT5xx touchscreen bindings to YAML,
fix them up a bit and extends them.
We list all the existing BT4xx and BT5xx components with compatible
strings. These are all similar, use the same bindings and work in
similar ways.
We rename the supplies from the erroneous vdd/vddo to the actual supply
names vcca/vdd as specified on the actual component. It is long
established that supplies shall be named after the supply pin names of a
component. The confusion probably stems from that in a certain product
the rails to the component were named vdd/vddo. Drop some notes on how OS
implementations should avoid confusion by first looking for vddo, and if
that exists assume the legacy binding pair and otherwise use vcca/vdd.
Add reset-gpios as sometimes manufacturers pulls a GPIO line to the reset
line on the chip.
Add optional touchscreen-fuzz-x and touchscreen-fuzz-y properties.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Fixed dt_schema_check]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-3-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The power button on Cherry Trail systems with an AXP288 PMIC is connected
to both the power button pin of the PMIC as well as to a power button GPIO
on the Cherry Trail SoC itself. This leads to double power button event
reporting which is a problem.
Since reporting power button presses through the PMIC is not supported on
all PMICs used on Cherry Trail systems, we want to keep the GPIO
power button events, so the axp20x-pek code checks for the presence of
a GPIO power button and in that case does not register its input-device.
On most systems the GPIO power button also can wake-up the system from
suspend, so the axp20x-pek driver would also not register its interrupt
handler. But on some systems there was a bug causing wakeup by the GPIO
power button handler to not work.
Commit 9747070c11 ("Input: axp20x-pek - always register interrupt
handlers") was added as a work around for this registering the axp20x-pek
interrupts, but not the input-device on Cherry Trail systems.
In the mean time the root-cause of the GPIO power button wakeup events
not working has been found and fixed by the "pinctrl: cherryview: Do not
allow the same interrupt line to be used by 2 pins" patch,
so this is no longer necessary.
This reverts the workaround going back to only registering the
interrupt handlers on systems where we also register the input-device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20220106111647.66520-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Variable ret is being assigned a value that is never read. If the
for-loop is entered then ret is immediately re-assigned a new
value. If the for-loop is not executed ret is never read. The
assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
When using the tpm_tis-spi driver on a system missing the physical TPM,
a null pointer exception was observed.
[ 0.938677] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 0.939020] pgd = 10c753cb
[ 0.939237] [00000004] *pgd=00000000
[ 0.939808] Internal error: Oops: 5 [#1] SMP ARM
[ 0.940157] CPU: 0 PID: 48 Comm: kworker/u4:1 Not tainted 5.15.10-dd1e40c #1
[ 0.940364] Hardware name: Generic DT based system
[ 0.940601] Workqueue: events_unbound async_run_entry_fn
[ 0.941048] PC is at tpm_tis_remove+0x28/0xb4
[ 0.941196] LR is at tpm_tis_core_init+0x170/0x6ac
This is due to an attempt in 'tpm_tis_remove' to use the drvdata, which
was not initialized in 'tpm_tis_core_init' prior to the first error.
Move the initialization of drvdata earlier so 'tpm_tis_remove' has
access to it.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Fixes: 79ca6f74da ("tpm: fix Atmel TPM crash caused by too frequent queries")
Cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Some SPI controller drivers unregister the controller in the shutdown
handler (e.g. BCM2835). If such a controller is used with a TPM 2 slave
chip->ops may be accessed when it is already NULL:
At system shutdown the pre-shutdown handler tpm_class_shutdown() shuts down
TPM 2 and sets chip->ops to NULL. Then at SPI controller unregistration
tpm_tis_spi_remove() is called and eventually calls tpm_del_char_device()
which tries to shut down TPM 2 again. Thereby it accesses chip->ops again:
(tpm_del_char_device calls tpm_chip_start which calls tpm_clk_enable which
calls chip->ops->clk_enable).
Avoid the NULL pointer access by testing if chip->ops is valid and skipping
the TPM 2 shutdown procedure in case it is NULL.
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Fixes: 39d0099f94 ("powerpc/pseries: Add shutdown() to vio_driver and vio_bus")
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
If something went wrong during the TPM firmware upgrade, like power
failure or the firmware image file get corrupted, the TPM might end
up in Upgrade or Failure mode upon the next start. The state is
persistent between the TPM power cycle/restart.
According to TPM specification:
* If the TPM is in Upgrade mode, it will answer with TPM2_RC_UPGRADE
to all commands except TPM2_FieldUpgradeData(). It may also accept
other commands if it is able to complete them using the previously
installed firmware.
* If the TPM is in Failure mode, it will allow performing TPM
initialization but will not provide any crypto operations.
Will happily respond to Field Upgrade calls.
Change the behavior of the tpm2_auto_startup(), so it detects the active
running mode of the TPM by adding the following checks. If
tpm2_do_selftest() call returns TPM2_RC_UPGRADE, the TPM is in Upgrade
mode.
If the TPM is in Failure mode, it will successfully respond to both
tpm2_do_selftest() and tpm2_startup() calls. Although, will fail to
answer to tpm2_get_cc_attrs_tbl(). Use this fact to conclude that TPM is
in Failure mode.
If detected that the TPM is in the Upgrade or Failure mode, the function
sets TPM_CHIP_FLAG_FIRMWARE_UPGRADE_MODE flag.
The TPM_CHIP_FLAG_FIRMWARE_UPGRADE_MODE flag is used later during driver
initialization/deinitialization to disable functionality which makes no
sense or will fail in the current TPM state. Following functionality is
affected:
* Do not register TPM as a hwrng
* Do not register sysfs entries which provide information impossible to
obtain in limited mode
* Do not register resource managed character device
Signed-off-by: axelj <axelj@axis.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Set TPM_FIRMWARE_POWER_MANAGED flag based on 'firmware-power-managed'
ACPI DSD property. For the CR50 TPM, this flag defaults to true when
the property is unset.
When this flag is set to false, the CR50 TPM driver will always send
a shutdown command whenever the system suspends.
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
There are non-root X.509 v3 certificates in use out there that contain
no Authority Key Identifier extension (RFC5280 section 4.2.1.1). For
trust verification purposes the kernel asymmetric key type keeps two
struct asymmetric_key_id instances that the key can be looked up by,
and another two to look up the key's issuer. The x509 public key type
and the PKCS7 type generate them from the SKID and AKID extensions in
the certificate. In effect current code has no way to look up the
issuer certificate for verification without the AKID.
To remedy this, add a third asymmetric_key_id blob to the arrays in
both asymmetric_key_id's (for certficate subject) and in the
public_keys_signature's auth_ids (for issuer lookup), using just raw
subject and issuer DNs from the certificate. Adapt
asymmetric_key_ids() and its callers to use the third ID for lookups
when none of the other two are available. Attempt to keep the logic
intact when they are, to minimise behaviour changes. Adapt the
restrict functions' NULL-checks to include that ID too. Do not modify
the lookup logic in pkcs7_verify.c, the AKID extensions are still
required there.
Internally use a new "dn:" prefix to the search specifier string
generated for the key lookup in find_asymmetric_key(). This tells
asymmetric_key_match_preparse to only match the data against the raw
DN in the third ID and shouldn't conflict with search specifiers
already in use.
In effect implement what (2) in the struct asymmetric_key_id comment
(include/keys/asymmetric-type.h) is probably talking about already, so
do not modify that comment. It is also how "openssl verify" looks up
issuer certificates without the AKID available. Lookups by the raw
DN are unambiguous only provided that the CAs respect the condition in
RFC5280 4.2.1.1 that the AKID may only be omitted if the CA uses
a single signing key.
The following is an example of two things that this change enables.
A self-signed ceritficate is generated following the example from
https://letsencrypt.org/docs/certificates-for-localhost/, and can be
looked up by an identifier and verified against itself by linking to a
restricted keyring -- both things not possible before due to the missing
AKID extension:
$ openssl req -x509 -out localhost.crt -outform DER -keyout localhost.key \
-newkey rsa:2048 -nodes -sha256 \
-subj '/CN=localhost' -extensions EXT -config <( \
echo -e "[dn]\nCN=localhost\n[req]\ndistinguished_name = dn\n[EXT]\n" \
"subjectAltName=DNS:localhost\nkeyUsage=digitalSignature\n" \
"extendedKeyUsage=serverAuth")
$ keyring=`keyctl newring test @u`
$ trusted=`keyctl padd asymmetric trusted $keyring < localhost.crt`; \
echo $trusted
39726322
$ keyctl search $keyring asymmetric dn:3112301006035504030c096c6f63616c686f7374
39726322
$ keyctl restrict_keyring $keyring asymmetric key_or_keyring:$trusted
$ keyctl padd asymmetric verified $keyring < localhost.crt
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Commit 79ca6f74da ("tpm: fix Atmel TPM crash caused by too frequent
queries") has moved some code around without updating the error handling
path.
This is now pointless to 'goto out_err' when neither 'clk_enable()' nor
'ioremap()' have been called yet.
Make a direct return instead to avoid undoing things that have not been
done.
Fixes: 79ca6f74da ("tpm: fix Atmel TPM crash caused by too frequent queries")
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
To allow this device to fill the kernel's entropy pool at boot,
setup a default quality for the hwrng found in Cr50.
After some testing with rngtest and dieharder it was, in short,
discovered that the RNG produces fair quality randomness, giving
around 99.93% successes in rngtest FIPS140-2.
Notably, though, when testing with dieharder it was noticed that
we get 3 WEAK results over 114, which isn't optimal, and also
the p-values distribution wasn't uniform in all the cases, so a
conservative quality value was chosen by applying an arbitrary
penalty to the calculated values.
For reference, this is how the values were calculated:
The dieharder results were averaged, then normalized (0-1000)
and re-averaged with the rngtest result (where the result was
given a score of 99.93% of 1000, so 999.3), then aggregated
together and averaged again.
An arbitrary penalty of -100 was applied due to the retrieved
value, which brings us finally to 700.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Remove parameter descriptions from all static functions.
Remove the comment altogether that does not tell what the function does.
Suggested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sohaib Mohamed <sohaib.amhmd@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Locality is not appropriately requested before writing the int mask.
Add the missing boilerplate.
Fixes: e6aef069b6 ("tpm_tis: convert to using locality callbacks")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Most distro kernels have this option enabled, to improve debug output.
Lockdep also selects it.
Enable this in the defconfig kernel as well, to make it more
representative of what people are using on x86.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/YdTn7gssoMVDMgMw@gmail.com
In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).
Fixes: 0a0b7a5f7a ("can: add driver for Softing card")
Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org
Cc: stable@vger.kernel.org # 2.6.38
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since [1], added in 5.7, the absence of a gpio-ranges property has
prevented GPIOs from being restored to inputs when released.
Add those properties for BCM283x and BCM2711 devices.
[1] commit 2ab73c6d83 ("gpio: Support GPIO controllers without
pin-ranges")
Link: https://lore.kernel.org/r/20220104170247.956760-1-linus.walleij@linaro.org
Fixes: 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
Fixes: 266423e60e ("pinctrl: bcm2835: Change init order for gpio hogs")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211206092237.4105895-3-phil@raspberrypi.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
A few more fixes have come in, nothing overly severe but would be good
to get in by final release:
- More specific compatible fields on the qspi controller for socfpga,
to enable quirks in the driver.
- A runtime PM fix for Renesas to fix mismatched reference counts on
errors.
-----BEGIN PGP SIGNATURE-----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=jTaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-5.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few more fixes have come in, nothing overly severe but would be good
to get in by final release:
- More specific compatible fields on the qspi controller for socfpga,
to enable quirks in the driver
- A runtime PM fix for Renesas to fix mismatched reference counts on
errors"
* tag 'soc-fixes-5.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: socfpga: change qspi to "intel,socfpga-qspi"
dt-bindings: spi: cadence-quadspi: document "intel,socfpga-qspi"
reset: renesas: Fix Runtime PM usage
This patch adds ethtool support to get the number of message buffers
configured for reception/transmission, which may also depends on
runtime configurations such as the 'rx-rtr' flag state.
Link: https://lore.kernel.org/all/20220108181633.420433-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
[mkl: port to net-next/master, replace __sw_hweight64 by simpler calculation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a private flag to the flexcan driver to switch the
"rx-rtr" setting on and off.
"rx-rtr" on - Receive RTR frames. (default)
The CAN controller can and will receive RTR frames.
On some IP cores the controller cannot receive RTR
frames in the more performant "RX mailbox" mode and
will use "RX FIFO" mode instead.
"rx-rtr" off - Waive ability to receive RTR frames. (not supported on all IP cores)
This mode activates the "RX mailbox mode" for better
performance, on some IP cores RTR frames cannot be
received anymore.
The "RX FIFO" mode uses a FIFO with a depth of 6 CAN frames.
The "RX mailbox" mode uses up to 62 mailboxes.
Link: https://lore.kernel.org/all/20220107193105.1699523-6-mkl@pengutronix.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Co-developed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull i2c fixes from Wolfram Sang:
"Fix the regression with AMD GPU suspend by reverting the
handling of bus regulators in the I2C core.
Also, there is a fix for the MPC driver to prevent an
out-of-bound-access"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: core: support bus regulator controlling in adapter"
i2c: mpc: Avoid out of bounds memory access
RTM says "If the special ONE stateid is passed to
nfs4_preprocess_stateid_op(), it returns status=0 but does not set
*cstid. nfsd4_copy_notify() depends on stid being set if status=0, and
thus can crash if the client sends the right COPY_NOTIFY RPC."
RFC 7862 says "The cna_src_stateid MUST refer to either open or locking
states provided earlier by the server. If it is invalid, then the
operation MUST fail."
The RFC doesn't specify an error, and the choice doesn't matter much as
this is clearly illegal client behavior, but bad_stateid seems
reasonable.
Simplest is just to guarantee that nfs4_preprocess_stateid_op, called
with non-NULL cstid, errors out if it can't return a stateid.
Reported-by: rtm@csail.mit.edu
Fixes: 624322f1ad ("NFSD add COPY_NOTIFY operation")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Olga Kornievskaia <kolga@netapp.com>
Tested-by: Olga Kornievskaia <kolga@netapp.com>
I'm cutting back on my responsibilities. The NFS server and file
locking code are in good hands.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
These functions are related to file handle processing and have
nothing to do with XDR encoding or decoding. Also they are no longer
NFSv3-specific. As a clean-up, move their definitions to a more
appropriate location. WCC is also an NFSv3-specific term, so rename
them as general-purpose helpers.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
