Skb with skb->protocol 0 at the time of virtio_net_hdr_to_skb may have
a protocol inferred from virtio_net_hdr with virtio_net_hdr_set_proto.
Unlike TCP, UDP does not have separate types for IPv4 and IPv6. Type
VIRTIO_NET_HDR_GSO_UDP is guessed to be IPv4/UDP. As of the below
commit, UFOv6 packets are dropped due to not matching the protocol as
obtained from dev_parse_header_protocol.
Invert the test to take that L2 protocol field as starting point and
pass both UFOv4 and UFOv6 for VIRTIO_NET_HDR_GSO_UDP.
Fixes: 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Link: https://lore.kernel.org/netdev/CABcq3pG9GRCYqFDBAJ48H1vpnnX=41u+MhQnayF1ztLH4WX0Fw@mail.gmail.com/
Reported-by: Andrew Melnichenko <andrew@daynix.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220144901.2784030-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tiny doc fix. The hardware transmit function was called skb_tstamp_tx
from its introduction in commit ac45f602ee ("net: infrastructure for
hardware time stamping") in the same series as this documentation.
Fixes: cb9eff0978 ("net: new user space API for time stamping of incoming and outgoing packets")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211220144608.2783526-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Raju Rangoju says:
====================
net: amd-xgbe: Add support for Yellow Carp Ethernet device
Add support for newer version of Hardware, the Yellow Carp Ethernet device
====================
Link: https://lore.kernel.org/r/20211220135428.1123575-1-rrangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yellow Carp Ethernet devices do not require
Autonegotiation CDR workaround, hence disable the same.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Newer generation Hardware uses the slightly different
port speed bit widths, so alter the existing port speed
bit range to extend support to the newer generation hardware
while maintaining the backward compatibility with older
generation hardware.
The previously reserved bits are now being used which
then requires the adjustment to the BIT values, e.g.:
Before:
PORT_PROPERTY_0[22:21] - Reserved
PORT_PROPERTY_0[26:23] - Supported Speeds
After:
PORT_PROPERTY_0[21] - Reserved
PORT_PROPERTY_0[26:22] - Supported Speeds
To make this backwards compatible, the existing BIT
definitions for the port speeds are incremented by one
to maintain the original position.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yellow Carp Ethernet devices use the existing PCI ID but
the window settings for the indirect PCS access have been
altered. Add the check for Yellow Carp Ethernet devices to
use the new register values.
Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In note_prot_wx() we bail out without reporting anything if
CONFIG_PPC_DEBUG_WX is disabled.
But CONFIG_PPC_DEBUG_WX was removed in the conversion to generic ptdump,
we now need to use CONFIG_DEBUG_WX instead.
Fixes: e084728393 ("powerpc/ptdump: Convert powerpc to GENERIC_PTDUMP")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20211203124112.2912562-1-mpe@ellerman.id.au
Last fixes before holidays:
- Work around a HW bug in HNS HIP08
- Recent memory leak regression in qib
- Incorrect use of kfree() for vmalloc memory in hns
-----BEGIN PGP SIGNATURE-----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=rRP8
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Last fixes before holidays. Nothing very exciting:
- Work around a HW bug in HNS HIP08
- Recent memory leak regression in qib
- Incorrect use of kfree() for vmalloc memory in hns"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/hns: Replace kfree() with kvfree()
IB/qib: Fix memory leak in qib_user_sdma_queue_pkts()
RDMA/hns: Fix RNR retransmission issue for HIP08
Both SoCs are known as 'lagoon' downstream. Add their ids to the socinfo
driver.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213081111.20217-1-luca.weiss@fairphone.com
Newer SoCs like SM6350 or SM8250 don't provide an interrupt for LLCC.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213082614.22651-9-luca.weiss@fairphone.com
Sort all power-domain defines and the SoC specific lists in
alphabetical order for better readability.
No functional changes.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1639063917-9011-5-git-send-email-quic_rjendra@quicinc.com
The requirement to specify the active + sleep and active-only MX
power-domains as the parents of the corresponding CX power domains is
not applicable on sc7280. Fix it by using the cx/cx_ao structs for
sc7280 instead of the _w_mx_parent ones.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1639063917-9011-4-git-send-email-quic_rjendra@quicinc.com
The rpmhpd structs were named with a SoC-name prefix, but then
they got reused across multiple SoC families making things confusing.
Rename all the struct names to remove SoC-name prefixes.
While we do this we end up with some power-domains without parents,
and some with and at times different parents across SoCs.
use a _w_<parent-name>_parent suffix for such cases.
No functional change as part of this patch.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1639063917-9011-3-git-send-email-quic_rjendra@quicinc.com
Add the power domains exposed by RPMH in the Qualcomm SM8450 platform.
Unlike previous generations CX domain is not a child of MX domain.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201072745.3969077-7-vkoul@kernel.org
Add compatible and constants for the power domains exposed by the RPMH
in the Qualcomm SM8450 platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201072745.3969077-6-vkoul@kernel.org
Update max processor count to reflect the number of co-processors on
SM8450 SoCs.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201072745.3969077-5-vkoul@kernel.org
The only usage of qmp_cooling_device_ops is to pass its address to
devm_thermal_of_cooling_device_register() which takes a pointer to const
struct thermal_cooling_device_ops as argument. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211128210317.25504-1-rikard.falkeborn@gmail.com
do_div() does a 64-by-32 division. Here the divisor is an unsigned long
which on some platforms is 64 bit wide. So use div64_ul instead of do_div
to avoid a possible truncation.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211125014311.45942-1-deng.changcheng@zte.com.cn
Not all RPM firmware versions have the dynamic sleep stats offset
available. Most older versions use a fixed offset of 0xdba0.
Add support for this using new SoC-specific compatibles for APQ8084,
MSM8226, MSM8916 and MSM8974.
Even older SoCs seem to use a different offset and stats format.
If needed those could be supported in the future by adding separate
compatibles for those with a different stats_config.
Cc: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211119213953.31970-3-stephan@gerhold.net
Document additional compatibles that can be used similarly to qcom,rpm-stats
for older RPM firmware versions that have the sleep stats at a fixed offset
rather than a dynamic one. The exact offset might vary depending on the SoC
so use SoC-specific compatible names to avoid confusion.
Cc: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211119213953.31970-2-stephan@gerhold.net
If GuC encounters an error during engine reset, the i915 driver
promotes to full GT reset. This includes an info message about why the
reset is happening. However, that is not treated as a failure by any
of the CI systems because resets are an expected occurrance during
testing. This kind of failure is a major problem and should never
happen. So, complain more loudly and make sure CI notices.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211211065859.2248188-4-John.C.Harrison@Intel.com
Lots of testing is done with the DEBUG_GEM config option enabled but
not the DEBUG_GUC option. That means we only get teeny-tiny GuC logs
which are not hugely useful. Enabling full DEBUG_GUC also spews lots
of other detailed output that is not generally desired. However,
bigger GuC logs are extremely useful for almost any regression debug.
So enable bigger logs for DEBUG_GEM builds as well.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211211065859.2248188-3-John.C.Harrison@Intel.com
Add support for telling the debugfs interface the size of the GuC log
dump in advance. Without that, the underlying framework keeps calling
the 'show' function with larger and larger buffer allocations until it
fits. That means reading the log from graphics memory many times - 16
times with the full 18MB log size.
v2: Don't return error codes from size query. Report overflow in the
error dump as well (review feedback from Daniele).
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211211065859.2248188-2-John.C.Harrison@Intel.com
The low level drivers don't expect to see new requests after a
successful quiesce completes. Check the queue quiesce state within the
rcu protected area prior to calling the driver's queue_rqs().
Fixes: 3c67d44de7 ("block: add mq_ops->queue_rqs hook")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20211220205919.180191-1-kbusch@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently we allow rediculous amounts of kernel memory being allocated
via the etnaviv GEM_SUBMIT ioctl, which is a pretty easy DoS vector. Put
some reasonable limits in to fix this.
The commandstream size is limited to 64KB, which was already a soft limit
on older kernels after which the kernel only took submits on a best effort
base, so there is no userspace that tries to submit commandstreams larger
than this. Even if the whole commandstream is a single incrementing address
load, the size limit also limits the number of potential relocs and
referenced buffers to slightly under 64K, so use the same limit for those
arguments. The performance monitoring infrastructure currently supports
less than 50 performance counter signals, so limiting them to 128 on a
single submit seems like a reasonably future-proof number for now. This
number can be bumped if needed without breaking the interface.
Cc: stable@vger.kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The running_trace_lock protects running_trace_list and is acquired
within the tracepoint which implies disabled preemption. The spinlock_t
typed lock can not be acquired with disabled preemption on PREEMPT_RT
because it becomes a sleeping lock.
The runtime of the tracepoint depends on the number of entries in
running_trace_list and has no limit. The blk-tracer is considered debug
code and higher latencies here are okay.
Make running_trace_lock a raw_spinlock_t.
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20211220192827.38297-1-wander@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Eliminates error messages if snd_soc_register_card() failed. Kernel
emits messages if device probe error anyway.
This is mainly for removing the following error messages during boot.
>>> snd_soc_register_card fail -517
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20211220093408.207206-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Zero-length arrays are deprecated and should be replaced with
flexible-array members.
Link: https://github.com/KSPP/linux/issues/78
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Make use of struct_size() helper instead of an open-coded calculation.
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Syzbot reports the following WARNING:
[200~raw_local_irq_restore() called with IRQs enabled
WARNING: CPU: 1 PID: 1206 at kernel/locking/irqflag-debug.c:10
warn_bogus_irq_restore+0x1d/0x20 kernel/locking/irqflag-debug.c:10
Hardware initialization for the rtl8188cu can run for as long as 350 ms,
and the routine may be called with interrupts disabled. To avoid locking
the machine for this long, the current routine saves the interrupt flags
and enables local interrupts. The problem is that it restores the flags
at the end without disabling local interrupts first.
This patch fixes commit a53268be0c ("rtlwifi: rtl8192cu: Fix too long
disable of IRQs").
Reported-by: syzbot+cce1ee31614c171f5595@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Fixes: a53268be0c ("rtlwifi: rtl8192cu: Fix too long disable of IRQs")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215171105.20623-1-Larry.Finger@lwfinger.net
The A-MPDU TX retransmission rate is always high (> 20%) even in a very
clean environment. However, the vendor driver retransimission rate is
< 10% in the same test bed. The difference is the vendor driver starts
the A-MPDU TXOP with initial RTS/CTS handshake which is observed in the
air capture and the TX descriptor. Since the driver does not know how
many frames will be aggregated and the estimated duration, forcing the
RTS/CTS protection for A-MPDU helps to lower the retransmission rate
from > 20% to ~12% in the same test setup with the vendor driver.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215085819.729345-1-chris.chiu@canonical.com
Migration of vmtest to libbpf/ci will change the address
of INDEX in vmtest.sh, which will cause vmtest.sh to not
work due to the failure of rootfs fetching.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: Lorenzo Fontana <lorenzo.fontana@elastic.co>
Link: https://lore.kernel.org/bpf/20211220050803.2670677-1-pulehui@huawei.com
These settings enables mac to detect and recover when rx fifo
circuit deadlock occurs. Previous version missed this, so we fix it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012708.8623-1-pkshih@realtek.com
Currently all realtek wifi chip is set to check CRC of VHT-SIG-B
in 802.11ac signal, but some AP don't calculate the CRC and packets
from these AP can't be received and lead to disconnection.
We disable the check defaultly to avoid this case.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012421.7859-1-pkshih@realtek.com
Many Intel based platforms face system random freeze after commit
9e2fd29864 ("rtw88: add napi support").
The commit itself shouldn't be the culprit. My guess is that the 8821CE
only leaves ASPM L1 for a short period when IRQ is raised. Since IRQ is
masked during NAPI polling, the PCIe link stays at L1 and makes RX DMA
extremely slow. Eventually the RX ring becomes messed up:
[ 1133.194697] rtw_8821ce 0000:02:00.0: pci bus timeout, check dma status
Since the 8821CE hardware may fail to leave ASPM L1, manually do it in
the driver to resolve the issue.
Fixes: 9e2fd29864 ("rtw88: add napi support")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215131
BugLink: https://bugs.launchpad.net/bugs/1927808
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215114635.333767-1-kai.heng.feng@canonical.com
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3b ("wilc1000: use goto labels on error path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
