Commit f45709df77 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df77 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().
Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller. Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear RTSD status before enabling the irq event for RTSD in
imx_uart_enable_wakeup function.
Since RTSD can be set as the wakeup source, this can avoid any risk of
false triggering of a wake-up interrupts.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125014306.4432-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patches, noone needs 'file' parameter in neither
ioctl hook from tty_ldisc_ops. So remove 'file' from both of them.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> [NFC]
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122094529.24171-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RoCE spec requires RoCE devices to support only the default pkey.
However the bnxt_re driver maintains a 0xFFFF entry pkey table and uses
only the first entry. Remove the pkey table and hard code a table of
length one hard wired with the default pkey.
Link: https://lore.kernel.org/r/20211125033615.483750-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Devesh Sharma <devesh.s.sharma@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Since commit a9c3f68f3c (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). All
users were converted in the previous patches, so remove
tty_schedule_flip() completely while inlining its body into
tty_flip_buffer_push().
One less exported function.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a9c3f68f3c (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). We are
going to remove the latter (as it is used less), so call the former in
the rest of the users.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a9c3f68f3c (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). We are
going to remove the latter (as it is used less), so call the former in
drivers/tty/.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the addrconf_addr_eui48() helper function to set the sys_image_guid,
Also make sure the GUID is valid EUI-64 identifier.
Link: https://lore.kernel.org/r/20211124102336.427637-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Acked-by: Bernard Metzler <bmt@zurich.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The type of min_latency is ktime_t, so use KTIME_MAX to initialize the
initial value.
Fixes: dc3b66a0ce ("RDMA/rtrs-clt: Add a minimum latency multipath policy")
Link: https://lore.kernel.org/r/20211124081040.19533-1-jinpu.wang@ionos.com
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Guoqing Jiang <Guoqing.Jiang@linux.dev>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
On the StarFive JH7100 RISC-V SoC the UART core clocks can't be set to
exactly 16 * 115200Hz and many other common bitrates. Trying this will
only result in a higher input clock, but low enough that the UART's
internal divisor can't come close enough to the baud rate target.
So rather than try to set the input clock it's better to skip the
clk_set_rate call and rely solely on the UART's internal divisor.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211116150119.2171-15-kernel@esmil.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have all the PCI device IDs unified, we can use
PCI_DEVICE_DATA() macro to simplify mxser's pci_device_id list, i.e.
mxser_pcibrds.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-20-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point having MOXA PCI device IDs in include/linux/pci_ids.h.
Move them to the driver and sort them all by the ID.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-19-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the MOXA PCI device IDs contain _MOXA_, some don't. Add it to
the latter, so that they are all unified.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-18-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser doesn't increase port->icount.buf_overrun at all. Do so if overrun
happens, so that it can be read from the stats.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-17-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous change (no plays with of tty->receive_room), the tty
parameter is unused.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First, checking tty->receive_room to signalize whether there is enough space
in the tty buffers does not make much sense. Provided the tty buffers
are in tty_port and those are not checked at all.
Second, if the rx path is throttled, with CRTSCTS, RTS is deasserted,
but is never asserted again. This leads to port "lockup", not accepting
any more input.
So:
1) stty -F /dev/ttyMI0 crtscts # the mxser port
2) stty -F /dev/ttyS6 crtscts # the connected port
3) cat /dev/ttyMI0
4) "write in a loop" to /dev/ttyS6
5) cat from 3) produces the bytes from 4)
6) killall -STOP cat (the 3)'s one)
7) wait for RTS to drop on /dev/ttyMI0
8) killall -CONT cat (again the 3)'s one)
cat erroneously produces no more output now (i.e. no data sent from
ttyS6 to ttyMI can be seen).
Note that the step 7) is performed twice: once from n_tty by
tty_throttle_safe(), once by mxser_stoprx() from the receive path. Then
after step 7), n_tty correctly unthrottles the input, but mxser calls
mxser_stoprx() again as there is still only a little space in n_tty
buffers (tty->receive_room mentioned at the beginning), but the device's
FIFO is/can be already filled.
After this patch, the output is correctly resumed, i.e. n_tty both
throttles and unthrottles without interfering with mxser's attempts.
This allows us to get rid of the non-standard ldisc_stop_rx flag from
struct mxser_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
timeout cannot be zero at the point of use. So no need to check for
zero. Also precompute the expiration time (into expire) and use it. This
makes the code more clear.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-14-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of schedule_timeout_interruptible(), because:
1) we don't have to bother with the task state, and
2) msleep* guarantees to sleep that time (if not interrupted).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-13-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And move it to new mxser_tx_empty(), because:
1) it simplifies the code (esp. the locking), and
2) serial_core needs such a hook anyway, so have it ready.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Finally, the mxser_close() code in is mostly identical to
tty_port_close(), so replace the code by a single call to the function.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I fail to see the point of calling mxser_flush_buffer() from
mxser_close():
1) The SW xmit buffer is freed in mxser_shutdown_port() right after the
call to mxser_flush_buffer(). And all 'cnt', 'head', and 'tail' are
properly initialized to 0 in mxser_activate().
2) The HW buffer is flushed in mxser_shutdown_port() via
mxser_disable_and_clear_FIFO() too.
So the effect of doing it by mxser_flush_buffer() in mxser_close() is
none. Hence remove it, so that when we use tty_port_close() later, the
code is 1:1 identical.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_stop_rx() should be called from mxser_shutdown_port() for several
reasons:
1) info->slock is held while manipulating IER (as on other places),
2) hangup now stops rx too,
3) mxser_close() will use tty_port_close() and there is no place except
tty_port_operations::shutdown() where this can be done,
4) this is the same sequence as serial_core does. So we can map this
code 1:1 when switching the driver to it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noone sets tty->driver_data to NULL in the driver, so there is no point
to check that in mxser_close(). Remove the check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xmit_buf is supposed to exist in all these functions. I.e. from
tty_port_operations::activate() to ::shutdown(). So remove these checks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port->icount.tx is handled in a too complicated manner. Instead of
remembering the original count and subtracting the new one from it,
simply increase tx for each character in the loop. No need for cnt
variable then.
Change also the "X = X & Y" assignment to simpler "X &= Y".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MSR read is currently performed on both places where
mxser_check_modem_status() is called. So move it there to avoid code
duplication.
Rename the variable to msr while we move it, to actually see what
"status" we are testing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The others are superfluous with tty refcounting in place now. And they
are racy in fact:
* tty_port_initialized() reports false for a small moment after
interrupts are enabled.
* closing is 1 while the port is still alive.
The queues are flushed later during close anyway. So there is no need
for this special handling. Actually, the ISR should not flush the
queues. It should behave as every other driver, just queue the chars
into tty buffer and go on. But this will be changed later. There is
still a lot code depending on having tty in ISR (and not only tty_port).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it is the only thing it does now. This is one of the future
serial_core hooks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_close() behaves like this:
-> tty_port_close_start()
-> tty_wait_until_sent()
-> mxser_wait_until_sent()
-> mxser_close_port
-> wait for TEMT
So it is already waited for TEMT through mxser_wait_until_sent() and
there is another round of waiting in mxser_close_port(). The latter one
is superfluous as nothing could be filled into the output FIFO. Remove
the call.
This helps unification among drivers (so that all behave the same) and
future use of tty_port_close().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On RZ/G2L SoC we need to explicitly deassert the reset line
for the device to work, use this opportunity to deassert/assert
reset line in sh-sci driver.
This patch adds support to read the "resets" property (if available)
from DT and perform deassert/assert when required.
Also, propagate the error to the caller of sci_parse_dt() instead of
returning NULL in case of failure.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make "resets" as required property for RZ/G2L. On RZ/G2L the devices
should be explicitly pulled out of reset for this reason make "resets"
as required property.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing tests are a little hard to comprehend. Use
check_add_overflow() instead.
Fixes: 04ded16724 ("RDMA/cma: Verify private data length")
Link: https://lore.kernel.org/r/1637661978-18770-1-git-send-email-haakon.bugge@oracle.com
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There are two consequent checks of uport != NULL in
uart_port_shutdown(). Join these two under a single block.
De-multiline the comments when shuffling with them anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both do_SAK_work() and vc_SAK() provide a valid tty to __do_SAK(), so
remove the check.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the TTY_SOFT_SAK part. It is never defined, so this is only
confusing.
It was actually never defined since its introduction in
0.99.14g.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118071911.12059-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 89d4f98ae9 ("ARM: remove zte zx platform") missed to remove some
definitions for this platform's debug and serial, e.g., code dependent on
the config DEBUG_ZTE_ZX.
Fortunately, ./scripts/checkkconfigsymbols.py detects this and warns:
DEBUG_ZTE_ZX
Referencing files: arch/arm/include/debug/pl01x.S
Further review by Arnd Bergmann identified even more dead code in the
amba serial driver.
Remove all this left-over from the zte zx platform.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20211102063810.932-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 'bitmap_zalloc()' to simplify code, improve the semantic and avoid
some open-coded arithmetic in allocator arguments.
Using the 'zalloc' version of the allocator also saves a now useless
'bitmap_zero()' call.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
While at it, remove an extra space in a statement just a few lines above.
Link: https://lore.kernel.org/r/e396c4aa16cd8945d43877570a8f6d926cea555a.1637789139.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In 'mthca_buddy_init()', the 'buddy->bits[n]' bitmap has just been
allocated, so no concurrent accesses can occur.
The other accesses to the 'buddy->bits[n]' bitmap are protected by the
'buddy->lock' spinlock, so no concurrent accesses can occur.
So prefer the non-atomic '__[set|clear]_bit()' functions to save a few
cycles.
Link: https://lore.kernel.org/r/a19b88ccdbc03972fd97306b998731814283041f.1637785902.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use 'bitmap_zalloc()' to simplify code, improve the semantic and avoid
some open-coded arithmetic in allocator arguments.
Using the 'zalloc' version of the allocator also saves a now useless
'bitmap_zero()' call.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Link: https://lore.kernel.org/r/ea9031e28f453bc179033740f66f0c19293fcf0b.1637785902.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The lpuart on i.MX8ULP is derived from i.MX7ULP, it uses two compatible
strings, so update the compatible string for i.MX8ULP.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20211120113454.785997-3-peng.fan@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jing Yao <yao.jing2@zte.com.cn>
Link: https://lore.kernel.org/r/20211104114754.30983-1-yao.jing2@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit b4b844930f ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>