commit bbc78c07a5 upstream.
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f0c2b68198 upstream.
When a signal is delivered, the information in the siginfo structure
is copied to userspace. Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user. This patch adds
such an initialization to the two places where usbfs raises signals.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dave Mielke <dave@mielke.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c99197902d upstream.
The usb_hcd_unlink_urb() routine in hcd.c contains two possible
use-after-free errors. The dev_dbg() statement at the end of the
routine dereferences urb and urb->dev even though both structures may
have been deallocated.
This patch fixes the problem by storing urb->dev in a local variable
(avoiding the dereference of urb) and moving the dev_dbg() up before
the usb_put_dev() call.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 074f9dd55f upstream.
Currently the USB stack assumes that all host controller drivers are
capable of receiving wakeup requests from downstream devices.
However, this isn't true for the isp1760-hcd driver, which means that
it isn't safe to do a runtime suspend of any device attached to a
root-hub port if the device requires wakeup.
This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure
and sets the flag in isp1760-hcd. The core is modified to prevent a
direct child of the root hub from being put into runtime suspend with
wakeup enabled if the flag is set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5efd2ea8c9 upstream.
the following error pops up during "testusb -a -t 10"
| musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128, f134e000/be842000 (bad dma)
hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of
size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in
hcd_buffer_alloc() returning memory which is 32 bytes aligned and it
might by identified by buffer_offset() as another buffer. This means the
buffer which is on a 32 byte boundary will not get freed, instead it
tries to free another buffer with the error message.
This patch fixes the issue by creating the smallest DMA buffer with the
size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is
smaller). This might be 32, 64 or even 128 bytes. The next three pools
will have the size 128, 512 and 2048.
In case the smallest pool is 128 bytes then we have only three pools
instead of four (and zero the first entry in the array).
The last pool size is always 2048 bytes which is the assumed PAGE_SIZE /
2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where
we would end up with 8KiB buffer in case we have 16KiB pages.
Instead I think it makes sense to have a common size(s) and extend them
if there is need to.
There is a BUILD_BUG_ON() now in case someone has a minalign of more than
128 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e5dff0e804 upstream.
OTG device shall support this device for allowing compliance automated testing.
The modification is derived from Pavankumar and Vijayavardhans' previous work.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Cc: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit cd83ce9e61 upstream.
This patch adds a usb quirk to support devices with interupt endpoints
and bInterval values expressed as microframes. The quirk causes the
parse endpoint function to modify the reported bInterval to a standards
conforming value.
There is currently code in the endpoint parser that checks for
bIntervals that are outside of the valid range (1-16 for USB 2+ high
speed and super speed interupt endpoints). In this case, the code assumes
the bInterval is being reported in 1ms frames. As well, the correction
is only applied if the original bInterval value is out of the 1-16 range.
With this quirk applied to the device, the bInterval will be
accurately adjusted from microframes to an exponent.
Signed-off-by: James P Michels III <james.p.michels@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: 3.16-stable prereq for:
e5dff0e804 "USB: Add OTG PET device to TPL" ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a32c99e7ab upstream.
The touchscreen needs the same quirk as the other models.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Bryan Poling <poli0048@umn.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 526a4045c6 upstream.
The usb device will autoresume from choose_wakeup() if it is
autosuspended with the wrong wakeup setting, but below errors occur
because usb3503 misc driver will switch to standby mode when suspended.
As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from
autosuspend_check().
[ 7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 7.854658] usb 1-3: device descriptor read/64, error -71
[ 8.079657] usb 1-3: device descriptor read/64, error -71
[ 8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 8.414658] usb 1-3: device descriptor read/64, error -71
[ 8.639657] usb 1-3: device descriptor read/64, error -71
[ 8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.264598] usb 1-3: device not accepting address 3, error -71
[ 9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.784601] usb 1-3: device not accepting address 3, error -71
[ 9.784838] usb usb1-port3: device 1-3 not suspended yet
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 263e80b435 upstream.
This wireless mouse receiver needs a reset-resume quirk to properly come
out of reset.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 876af5d454 upstream.
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c68929f75d upstream.
Enable device-qualifier quirk for Elan Touchscreen, which often fails to
handle requests for the device_descriptor.
Note that the device sometimes do respond properly with a Request Error
(three times as USB core retries), but usually fails to respond at all.
When this happens any further descriptor requests also fails, for
example:
[ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd
[ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71
[ 1530.945592] usb 2-7: can't read configurations, error -71
This has been observed repeating for over a minute before eventual
successful enumeration.
Reported-by: Drew Von Spreecken <drewvs@gmail.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2a159389bf upstream.
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: prereq for the following Elan touchscreen patches ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 90a646c770 upstream.
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ddbe1fca0b upstream.
This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.
This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.
This patch could be back-ported to kernels as old as 2.6.39.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c605f3cdff upstream.
During surprise device hotplug removal tests, it was observed that
hub_events may try to call usb_lock_device on a device that has already
been freed. Protect the usb_device by taking out a reference (under the
hub_event_lock) when hub_events pulls it off the list, returning the
reference after hub_events is finished using it.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref
Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9ef803d74 upstream.
commit bdd405d2a5 ("usb: hub: Prevent hub autosuspend if
usbcore.autosuspend is -1") causes a build error if CONFIG_PM_RUNTIME is
disabled. Fix that by doing a simple #ifdef guard around it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Michael Welling <mwelling@emacinc.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd5f5006d1 upstream.
The commit [5ee0f803cc: usbcore: don't log on consecutive debounce
failures of the same port] added the check of the reliable port, but
it also replaced the device argument to dev_err() wrongly, which leads
to a NULL dereference.
This patch restores the right device, port_dev->dev. Also, since
dev_err() itself shows the port number, reduce the port number shown
in the error message, essentially reverting to the state before the
commit 5ee0f803cc.
[The fix suggested by Hannes, and the error message cleanup suggested
by Alan Stern]
Fixes: 5ee0f803cc ('usbcore: don't log on consecutive debounce failures of the same port')
Reported-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bdd405d2a5 upstream.
If user specifies that USB autosuspend must be disabled by module
parameter "usbcore.autosuspend=-1" then we must prevent
autosuspend of USB hub devices as well.
commit 596d789a21 introduced in v3.8 changed the original behaivour
and stopped respecting the usbcore.autosuspend parameter for hubs.
Fixes: 596d789a21 "USB: set hub's default autosuspend delay as 0"
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michael Welling <mwelling@emacinc.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a40178b2fa upstream.
Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others. Such
devices fail to reconnect with same old address which was associated
with it before suspend.
When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.
Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port. In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.
Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.
I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.
So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.
XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present. USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.
This patch implements above delay, but only for SS device and when
persist is enabled.
So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.
Results:
Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d310d05f12 upstream.
usbfs allows user space to pass down an URB which sets URB_SHORT_NOT_OK
for output URBs. That causes usbcore to log messages without limit
for a nonsensical disallowed combination. The fix is to silently drop
the attribute in usbfs.
The problem is reported to exist since 3.14
https://www.virtualbox.org/ticket/13085
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ee0f803cc upstream.
Some laptops have an internal port for a BT device which picks
up noise when the kill switch is used, but not enough to trigger
printk_rlimit(). So we shouldn't log consecutive faults of this kind.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().
Fixes: 41e7e056cd (USB: Allow USB 3.0 ports to be disabled.)
Signed-off-by: Gavin Guo <gavin.guo@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9262c19d14 "usb: disable port power control if not supported in
wHubCharacteristics" gated enabling runtime pm for usb_port devices on
whether the parent hub supports power control, which causes a
regression. The port must still be allowed to carry out runtime pm
callbacks and receive a -EAGAIN or -EBUSY result. Otherwise the
usb_port device will transition to the pm error state and trigger the
same for the child usb_device.
Prior to the offending commit usb_hub_create_port_device() arranged for
runtime pm to be disabled is dev_pm_qos_expose_flags() failed. Instead,
force the default state of PM_QOS_FLAG_NO_POWER_OFF flag to be set prior
to enabling runtime pm. If that policy can not be set then fail
registration.
Report: http://marc.info/?l=linux-usb&m=140290586301336&w=2
Fixes: 9262c19d14 ("usb: disable port power control if not supported in wHubCharacteristics")
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where platform firmware has specified conflicting values for
port locations it is confusing and otherwise not helpful to throw a
backtrace. Instead, include enough information to determine that
firmware has done something wrong and globally disable port poweroff.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading through a recent bug report [1], Alan notes:
"Dan, the warning message in hub_suspend() should mention that the
child device isn't suspended yet."
...update the warning from:
"usb usb3-port4: not suspended yet"
...to:
"usb usb3-port4: device 3-4: not suspended yet"
[1]: http://marc.info/?l=linux-usb&m=140290586301336&w=2
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d8521afe35 "usb: assign default peer ports for root hubs"
delayed marking a hub valid (set hdev->maxchild) until it had been fully
configured and to enable the publishing of valid hubs to be serialized
by usb_port_peer_mutex.
However, xhci_update_hub_device() in some cases depends on
hdev->maxchild already being set. Do the minimal fix and move it after
the setting of hdev->maxchild.
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Tested-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unconditionally wake up the child device when the power session is
recovered.
This addresses the following scenarios:
1/ The device may need a reset on power-session loss, without this
change port power-on recovery exposes khubd to scenarios that
usb_port_resume() is set to handle. Prior to port power control the
only time a power session would be lost is during dpm_suspend of the
hub. In that scenario usb_port_resume() is guaranteed to be called
prior to khubd running for that port. With this change we wakeup the
child device as soon as possible (prior to khubd running again for this
port).
Although khubd has facilities to wake a child device it will only do
so if the portstatus / portchange indicates a suspend state. In the
case of port power control we are not coming from a hub-port-suspend
state. This implementation simply uses pm_request_resume() to wake the
device and relies on the port_dev->status_lock to prevent any collisions
between khubd and usb_port_resume().
2/ This mechanism rate limits port power toggling. The minimum port
power on/off period is now gated by the child device suspend/resume
latency. Empirically this mitigates devices downgrading their connection
on perceived instability of the host connection. This ratelimiting is
really only relevant to port power control testing, but it is a nice
side effect of closing the above race. Namely, the race of khubd for
the given port running while a usb_port_resume() event is pending.
3/ Going forward we are finding that power-session recovery requires
warm-resets (http://marc.info/?t=138659232900003&r=1&w=2). This
mechanism allows for warm-resets to be requested at the same point in
the resume path for hub dpm_suspend power session losses, or port
rpm_suspend power session losses.
4/ If the device *was* disconnected the only time we'll know for sure is
after a failed resume, so it's necessary for usb_port_runtime_resume()
to expedite a usb_port_resume() to clean up the removed device. The
reasoning for this is "least surprise" for the user. Turning on a port
means that hotplug detection is again enabled for the port, it is
surprising that devices that were removed while the port was off are not
disconnected until they are attempted to be used. As a user "why would
I try to use a device I removed from the system?"
1, 2, and 4 are not a problem in the system dpm_resume() case because,
although the power-session is lost, khubd is frozen until after device
resume. For the rpm_resume() case pm_request_resume() is used to
request re-validation of the device, and if it happens to collide with a
khubd run we rely on the port_dev->status_lock to synchronize those
operations.
Besides testing, the primary scenario where this mechanism is expected
to be triggered is when the user changes the port power policy
(control/pm_qos_no_poweroff, or power/control). Each time power is
enabled want to revalidate the child device, where the revalidation is
handled by usb_port_resume().
Given that this arranges for port_dev->child to be de-referenced in
usb_port_runtime_resume() we need to make sure not to collide with
usb_disconnect() that frees the usb_device. To this end we hold the
port active with the "child_usage" reference across the disconnect
event. Subsequently, the need to access hub->child_usage_bits lead to
the creation of hub_disconnect_children() to remove any ambiguity of
which "hub" is being acted on in usb_disconnect() (prompted-by sharp
eyes from Alan).
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per Alan:
"You mean from within hub_handle_remote_wakeup()? That routine will
never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd
never sees wakeup requests if they arise during system suspend.
In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME"
portion of hub.c, along with the other suspend/resume code."
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In general we do not want khubd to act on port status changes that are
the result of in progress resets or USB runtime PM operations.
Specifically port power control testing has been able to trigger an
unintended disconnect in hub_port_connect_change(), paraphrasing:
if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
udev->state != USB_STATE_NOTATTACHED) {
if (portstatus & USB_PORT_STAT_ENABLE) {
/* Nothing to do */
} else if (udev->state == USB_STATE_SUSPENDED &&
udev->persist_enabled) {
...
} else {
/* Don't resuscitate */;
}
}
...by falling to the "Don't resuscitate" path or missing
USB_PORT_STAT_CONNECTION because usb_port_resume() was in the middle of
modifying the port status.
So, we want a new lock to hold off khubd for a given port while the
child device is being suspended, resumed, or reset. The lock ordering
rules are now usb_lock_device() => usb_lock_port(). This is mandated by
the device core which may hold the device_lock on the usb_device before
invoking usb_port_{suspend|resume} which in turn take the status_lock on
the usb_port. We attempt to hold the status_lock for the duration of a
port_event() run, and drop/re-acquire it when needing to take the
device_lock. The lock is also dropped/re-acquired during
hub_port_reconnect().
This patch also deletes hub->busy_bits as all use cases are now covered
by port PM runtime synchronization or the port->status_lock and it
pushes down usb_device_lock() into usb_remote_wakeup().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a port is powered-off, or in the process of being powered-off, prevent
khubd from operating on it. Otherwise, the following sequence of events
leading to an unintended disconnect may occur:
Events:
(0) <set pm_qos_no_poweroff to '0' for port1>
(1) hub 2-2:1.0: hub_resume
(2) hub 2-2:1.0: port 1: status 0301 change 0000
(3) hub 2-2:1.0: state 7 ports 4 chg 0002 evt 0000
(4) hub 2-2:1.0: port 1, power off status 0000, change 0000, 12 Mb/s
(5) usb 2-2.1: USB disconnect, device number 5
Description:
(1) hub is resumed before sending a ClearPortFeature request
(2) hub_activate() notices the port is connected and sets
hub->change_bits for the port
(3) hub_events() starts, but at the same time the port suspends
(4) hub_connect_change() sees the disabled port and triggers disconnect
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for synchronizing port handling with pm_runtime
transitions refactor port handling into its own subroutine.
We expect that clearing some status flags will be required regardless of
the port state, so handle those first and group all non-trivial actions
at the bottom of the routine.
This also splits off the bottom half of hub_port_connect_change() into
hub_port_reconnect() in prepartion for introducing a port->status_lock.
hub_port_reconnect() will expect the port lock to not be held while
hub_port_connect_change() expects to enter with it held.
Other cleanups include:
1/ reflowing to 80 columns
2/ replacing redundant usages of 'hub->hdev' with 'hdev'
3/ consolidate clearing of ->change_bits() in hub_port_connect_change
4/ consolidate calls to usb_reset_device
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port pm_runtime implementation unconditionally clears FEAT_C_ENABLE
after clearing PORT_POWER, but the bit is reserved on usb3 hub ports.
We expect khubd to be prevented from running because the port state is
not RPM_ACTIVE, so we need to clear any errors for usb2 ports.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three reasons:
1/ It's an invalid operation on usb3 ports
2/ There's no guarantee of when / if a usb2 port has entered an error
state relative to PORT_POWER request
3/ The port is active / powered at this point, so khubd will clear it as
a matter of course
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ClearPortFeature(PORT_POWER) on a usb3 port places the port in either a
DSPORT.Powered-off-detect / DSPORT.Powered-off-reset loop, or the
DSPORT.Powered-off state. There is no way to ensure that RX
terminations will persist in this state, so it is possible a device will
degrade to its usb2 connection. Prevent this by blocking power-off of a
usb3 port while its usb2 peer is active, and powering on a usb3 port
before its usb2 peer.
By default the latency between peer power-on events is 0. In order for
the device to not see usb2 active while usb3 is still powering up inject
the hub recommended power_on_good delay. In support of satisfying the
power_on_good delay outside of hub_power_on() refactor the places where
the delay is consumed to call a new hub_power_on_good_delay() helper.
Finally, because this introduces several new checks for whether a port
is_superspeed, cache that disctinction at port creation so that we don't
need to keep looking up the parent hub device.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[alan]: add a 'superspeed' flag to the port
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to manipulate ->did_runtime_put in usb_port_runtime_resume(),
but we don't want that to collide with other updates. Move usb_port
flags to new port-bitmap fields in usb_hub. "did_runtime_put" is renamed
"child_usage_bits" to reflect that it is strictly standing in for the
fact that usb_devices are not the device_model children of their parent
port.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI identifies peer ports by setting their 'group_token' and
'group_position' _PLD data to the same value. If a platform has tier
mismatch [1] , ACPI can override the default (USB3 defined) peer port
association for internal hubs. External hubs follow the default peer
association scheme.
Location data is cached as an opaque cookie in usb_port_location data.
Note that we only consider the group_token and group_position attributes
from the _PLD data as ACPI specifies that group_token is a unique
identifier.
When we find port location data for a port then we assume that the
firmware will also describe its peer port. This allows the
implementation to only ever set the peer once. This leads to a question
about what happens when a pm runtime event occurs while the peer
associations are still resolving. Since we only ever set the peer
information once, a USB3 port needs to be prevented from suspending
while its ->peer pointer is NULL (implemented in a subsequent patch).
There is always the possibility that firmware mis-identifies the ports,
but there is not much the kernel can do in that case.
[1]: xhci 1.1 appendix D figure 131
[2]: acpi 5 section 6.1.8
[alan]: don't do default peering when acpi data present
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Given that root hub port peers are already established, external hub peer
ports can be determined by traversing the device topology:
1/ ascend to the parent hub and find the upstream port_dev
2/ walk ->peer to find the peer port
3/ descend to the peer hub via ->child
4/ find the port with the matching port id
Note that this assumes the port labeling scheme required by the
specification [1].
[1]: usb3 3.1 section 10.3.3
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assume that the peer of a superspeed port is the port with the same id
on the shared_hcd root hub. This identification scheme is required of
external hubs by the USB3 spec [1]. However, for root hubs, tier mismatch
may be in effect [2]. Tier mismatch can only be enumerated via platform
firmware. For now, simply perform the nominal association.
A new lock 'usb_port_peer_mutex' is introduced to synchronize port
device add/remove with peer lookups. It protects peering against
changes to hcd->shared_hcd, hcd->self.root_hub, hdev->maxchild, and
port_dev->child pointers.
[1]: usb 3.1 section 10.3.3
[2]: xhci 1.1 appendix D
Cc: Alan Stern <stern@rowland.harvard.edu>
[alan: usb_port_peer_mutex locking scheme]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once usb-acpi has set the port's connect type the usb_device's
->removable attribute can be set in the standard location
set_usb_port_removable().
This also changes behavior in the case where the firmware says that the
port connect type is unknown. In that case just use the default setting
determined from the hub descriptor.
Note, we no longer pass udev->portnum to acpi_find_child_device() in the
root hub case since:
1/ the usb-core sets this to zero
2/ acpi always expects zero
...just pass zero.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current port name "portX" is ambiguous. Before adding more port
messages rename ports to "<hub-device-name>-portX"
This is an ABI change, but the suspicion is that it will go unnoticed as
the port power control implementation has been broken since its
introduction. If however, someone was relying on the old name we can
add sysfs links from the old name to the new name.
Additionally, it unifies/simplifies port dev_printk messages and modifies
instances of:
dev_XXX(hub->intfdev, ..."port %d"...
dev_XXX(&hdev->dev, ..."port%d"...
into:
dev_XXX(&port_dev->dev, ...
Now that the names are unique usb_port devices it would be nice if they
could be included in /sys/bus/usb. However, it turns out that this
breaks 'lsusb -t'. For now, create a dummy port driver so that print
messages are prefixed "usb 1-1-port3" rather than the
subsystem-ambiguous " 1-1-port3".
Finally, it corrects an odd usage of sscanf("port%d") in usb-acpi.c.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A hub indicates whether it supports per-port power control via the
wHubCharacteristics field in its descriptor. If it is not supported
a hub will still emulate ClearPortPower(PORT_POWER) requests by
stopping the link state machine. However, since this does not save
power do not bother suspending.
This also consolidates support checks into a
hub_is_port_power_switchable() helper.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core doesn't properly handle mutual exclusion between
resetting a hub and changing the power states of the hub's ports. We
need to avoid sending port-power requests to the hub while it is being
reset, because such requests cannot succeed.
This patch fixes the problem by keeping track of when a reset is in
progress. At such times, attempts to suspend (power-off) a port will
fail immediately with -EBUSY, and calls to usb_port_runtime_resume()
will update the power_is_on flag and return immediately. When the
reset is complete, hub_activate() will automatically restore each port
to the proper power state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch creates a separate instance of the usb_address0 mutex for each USB
bus, and attaches it to the usb_bus device struct. This allows devices on
separate buses to be enumerated in parallel; saving time.
In the current code, there is a single, global instance of the usb_address0
mutex which is used for all devices on all buses. This isn't completely
necessary, as this mutex is only needed to prevent address0 collisions for
devices on the *same* bus (usb 2.0 spec, sec 4.6.1). This superfluous coverage
can cause additional delay in system resume on systems with multiple hosts
(up to several seconds depending on what devices are attached).
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since usb otg fsm implementation is not related to usb phy.
We move it from usb/phy/ to usb/common/, and rename it to
reflect its real meaning.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have already removed the usage of CONFIG_USB_DEBUG, it is
meaningless that there is still a configuration entry for CONFIG_USB_DEBUG.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
