If a userspace process reads (with O_DIRECT) multiple blocks into the same
buffer, dm-verity reports an error [1].
This commit fixes dm-verity, so that if hash verification fails, the data
is read again into a kernel buffer (where userspace can't modify it) and
the hash is rechecked. If the recheck succeeds, the content of the kernel
buffer is copied into the user buffer; if the recheck fails, an error is
reported.
[1] https://people.redhat.com/~mpatocka/testcases/blk-auth-modify/read2.c
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
If a userspace process reads (with O_DIRECT) multiple blocks into the same
buffer, dm-integrity reports an error [1]. The error is reported in a log
and it may cause RAID leg being kicked out of the array.
This commit fixes dm-integrity, so that if integrity verification fails,
the data is read again into a kernel buffer (where userspace can't modify
it) and the integrity tag is rechecked. If the recheck succeeds, the
content of the kernel buffer is copied into the user buffer; if the
recheck fails, an integrity error is reported.
[1] https://people.redhat.com/~mpatocka/testcases/blk-auth-modify/read2.c
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Do not allow to set phase adjust value for a pin if PF reset is in
progress, this would cause confusing netlink extack errors as the firmware
cannot process the request properly during the reset time.
Return (-EBUSY) and report extack error for the user who tries configure
pin phase adjust during the reset time.
Test by looping execution of below steps until netlink error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
- change pin phase adjust value:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-set --json '{"id":0, "phase-adjust":1000}'
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do not allow dpll periodic work function to acquire data from firmware
if PF reset is in progress. Acquiring data will cause dmesg errors as the
firmware cannot respond or process the request properly during the reset
time.
Test by looping execution of below step until dmesg error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Igor Bagnucki <igor.bagnucki@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do not allow to acquire data or alter configuration of dpll and pins
through firmware if PF reset is in progress, this would cause confusing
netlink extack errors as the firmware cannot respond or process the
request properly during the reset time.
Return (-EBUSY) and extack error for the user who tries access/modify
the config of dpll/pin through firmware during the reset time.
The PF reset and kernel access to dpll data are both asynchronous. It is
not possible to guard all the possible reset paths with any determinictic
approach. I.e., it is possible that reset starts after reset check is
performed (or if the reset would be checked after mutex is locked), but at
the same time it is not possible to wait for dpll mutex unlock in the
reset flow.
This is best effort solution to at least give a clue to the user
what is happening in most of the cases, knowing that there are possible
race conditions where the user could see a different error received
from firmware due to reset unexpectedly starting.
Test by looping execution of below steps until netlink error appears:
- perform PF reset
$ echo 1 > /sys/class/net/<ice PF>/device/reset
- i.e. try to alter/read dpll/pin config:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--dump pin-get
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The value of phase_adjust for input pin shall be updated in
ice_dpll_pin_state_update(..). Fix by adding proper argument to the
firmware query function call - a pin's struct field pointer where the
phase_adjust value during driver runtime is stored.
Previously the phase_adjust used to misinform user about actual
phase_adjust value. I.e., if phase_adjust was set to a non zero value and
if driver was reloaded, the user would see the value equal 0, which is
not correct - the actual value is equal to value set before driver reload.
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the connection state between source DPLL and output pin, updating the
attribute 'state' of 'parent_device'. Previously, the connection state
was broken, and didn't reflect the correct state.
When 'state_on_dpll_set' is called with the value
'DPLL_PIN_STATE_CONNECTED' (1), the output pin will switch to the given
DPLL, and the state of the given DPLL will be set to connected.
E.g.:
--do pin-set --json '{"id":2, "parent-device":{"parent-id":1,
"state": 1 }}'
This command will connect DPLL device with id 1 to output pin with id 2.
When 'state_on_dpll_set' is called with the value
'DPLL_PIN_STATE_DISCONNECTED' (2) and the given DPLL is currently
connected, then the output pin will be disabled.
E.g:
--do pin-set --json '{"id":2, "parent-device":{"parent-id":1,
"state": 2 }}'
This command will disable output pin with id 2 if DPLL device with ID 1 is
connected to it; otherwise, the command is ignored.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On arm64, kprobes always take an exception and so create a struct
pt_regs through the usual exception entry logic. Similarly kretprobes
taskes and exception for function entry, but for function returns it
uses a trampoline which attempts to create a struct pt_regs without
taking an exception.
This is problematic for a few reasons, including:
1) The kretprobes trampoline neither saves nor restores all of the
portions of PSTATE. Before invoking the handler it saves a number of
portions of PSTATE, and after returning from the handler it restores
NZCV before returning to the original return address provided by the
handler.
2) The kretprobe trampoline constructs the PSTATE value piecemeal from
special purpose registers as it cannot read all of PSTATE atomically
without taking an exception. This is somewhat fragile, and it's not
possible to reliably recover PSTATE information which only exists on
some physical CPUs (e.g. when SSBS support is mismatched).
Today the kretprobes trampoline does not record:
- BTYPE
- SSBS
- ALLINT
- SS
- PAN
- UAO
- DIT
- TCO
... and this will only get worse with future architecture extensions
which add more PSTATE bits.
3) The kretprobes trampoline doesn't store portions of struct pt_regs
(e.g. the PMR value when using pseudo-NMIs). Due to this, helpers
which operate on a struct pt_regs, such as interrupts_enabled(), may
not work correctly.
4) The function entry and function exit handlers run in different
contexts. The entry handler will always be run in a debug exception
context (which is currently treated as an NMI), but the return will
be treated as whatever context the instrumented function was executed
in. The differences between these contexts are liable to cause
problems (e.g. as the two can be differently interruptible or
preemptible, adversely affecting synchronization between the
handlers).
5) As the kretprobes trampoline runs in the same context as the code
being probed, it is subject to the same single-stepping context,
which may not be desirable if this is being driven by the kprobes
handlers.
Overall, this is fragile, painful to maintain, and gets in the way of
supporting other things (e.g. RELIABLE_STACKTRACE, FEAT_NMI).
This patch addresses these issues by replacing the kretprobes trampoline
with a `BRK` instruction, and using an exception boundary to acquire and
restore the regs, in the same way as the regular kprobes trampoline.
Ive tested this atop v6.8-rc3:
| KTAP version 1
| 1..1
| KTAP version 1
| # Subtest: kprobes_test
| # module: test_kprobes
| 1..7
| ok 1 test_kprobe
| ok 2 test_kprobes
| ok 3 test_kprobe_missed
| ok 4 test_kretprobe
| ok 5 test_kretprobes
| ok 6 test_stacktrace_on_kretprobe
| ok 7 test_stacktrace_on_nested_kretprobe
| # kprobes_test: pass:7 fail:0 skip:0 total:7
| # Totals: pass:7 fail:0 skip:0 total:7
| ok 1 kprobes_test
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Florent Revest <revest@chromium.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20240208145916.2004154-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When returning to a user context, the arm64 entry code masks all DAIF
exceptions before handling pending work in exit_to_user_mode_prepare()
and do_notify_resume(), where it will transiently unmask all DAIF
exceptions. This is a holdover from the old entry assembly, which
conservatively masked all DAIF exceptions, and it's only necessary to
mask interrupts at this point during the exception return path, so long
as we subsequently mask all DAIF exceptions before the actual exception
return.
While most DAIF manipulation follows a save...restore sequence, the
manipulation in do_notify_resume() is the other way around, unmasking
all DAIF exceptions before masking them again. This is unfortunate as we
unnecessarily mask Debug and SError exceptions, and it would be nice to
remove this special case to make DAIF manipulation simpler and most
consistent.
This patch changes exit_to_user_mode_prepare() and do_notify_resume() to
only mask interrupts while handling pending work, masking other DAIF
exceptions after this has completed. This removes the unusual DAIF
manipulation and allows Debug and SError exceptions to be taken for a
slightly longer window during the exception return path.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
Currently do_notify_resume() lives in arch/arm64/kernel/signal.c, but it would
make more sense for it to live in entry-common.c as it handles more than
signals, and is coupled with the rest of the return-to-userspace sequence (e.g.
with unusual DAIF masking that matches the exception return requirements).
Move do_notify_resume() to entry-common.c.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-3-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
In do_notify_resume, we handle _TIF_NEED_RESCHED differently from all
other flags, leaving IRQ+FIQ masked when calling into schedule(). This
masking is a historical artifact, and it is not currently necessary
to mask IRQ+FIQ when calling into schedule (as evidenced by the generic
exit_to_user_mode_loop(), which unmasks IRQs before checking
_TIF_NEED_RESCHED and calling schedule()).
This patch removes the special case for _TIF_NEED_RESCHED, moving this
check into the main loop such that schedule() will be called from a
regular process context with IRQ+FIQ unmasked. This is a minor
simplification to do_notify_resume() and brings it into line with the
generic exit_to_user_mode_loop() logic. This will also aid subsequent
rework of DAIF management.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240206123848.1696480-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Itaru Kitayama <itaru.kitayama@linux.dev>
Currently our IO accessors all use register addressing without offsets,
but we could safely use offset addressing (without writeback) to
simplify and optimize the generated code.
To function correctly under a hypervisor which emulates IO accesses, we
must ensure that any faulting/trapped IO access results in an ESR_ELx
value with ESR_ELX.ISS.ISV=1 and with the tranfer register described in
ESR_ELx.ISS.SRT. This means that we can only use loads/stores of a
single general purpose register (or the zero register), and must avoid
writeback addressing modes. However, we can use immediate offset
addressing modes, as these still provide ESR_ELX.ISS.ISV=1 and a valid
ESR_ELx.ISS.SRT when those accesses fault at Stage-2.
Currently we only use register addressing without offsets. We use the
"r" constraint to place the address into a register, and manually
generate the register addressing by surrounding the resulting register
operand with square braces, e.g.
| static __always_inline void __raw_writeq(u64 val, volatile void __iomem *addr)
| {
| asm volatile("str %x0, [%1]" : : "rZ" (val), "r" (addr));
| }
Due to this, sequences of adjacent accesses need to generate addresses
using separate instructions. For example, the following code:
| void writeq_zero_8_times(void *ptr)
| {
| writeq_relaxed(0, ptr + 8 * 0);
| writeq_relaxed(0, ptr + 8 * 1);
| writeq_relaxed(0, ptr + 8 * 2);
| writeq_relaxed(0, ptr + 8 * 3);
| writeq_relaxed(0, ptr + 8 * 4);
| writeq_relaxed(0, ptr + 8 * 5);
| writeq_relaxed(0, ptr + 8 * 6);
| writeq_relaxed(0, ptr + 8 * 7);
| }
... is compiled to:
| <writeq_zero_8_times>:
| str xzr, [x0]
| add x1, x0, #0x8
| str xzr, [x1]
| add x1, x0, #0x10
| str xzr, [x1]
| add x1, x0, #0x18
| str xzr, [x1]
| add x1, x0, #0x20
| str xzr, [x1]
| add x1, x0, #0x28
| str xzr, [x1]
| add x1, x0, #0x30
| str xzr, [x1]
| add x0, x0, #0x38
| str xzr, [x0]
| ret
As described above, we could safely use immediate offset addressing,
which would allow the ADDs to be folded into the address generation for
the STRs, resulting in simpler and smaller generated assembly. We can do
this by using the "o" constraint to allow the compiler to generate
offset addressing (without writeback) for a memory operand, e.g.
| static __always_inline void __raw_writeq(u64 val, volatile void __iomem *addr)
| {
| volatile u64 __iomem *ptr = addr;
| asm volatile("str %x0, %1" : : "rZ" (val), "o" (*ptr));
| }
... which results in the earlier code sequence being compiled to:
| <writeq_zero_8_times>:
| str xzr, [x0]
| str xzr, [x0, #8]
| str xzr, [x0, #16]
| str xzr, [x0, #24]
| str xzr, [x0, #32]
| str xzr, [x0, #40]
| str xzr, [x0, #48]
| str xzr, [x0, #56]
| ret
As Will notes at:
https://lore.kernel.org/linux-arm-kernel/20240117160528.GA3398@willie-the-truck/
... some compilers struggle with a plain "o" constraint, so it's
preferable to use "Qo", where the additional "Q" constraint permits
using non-offset register addressing.
This patch modifies our IO write accessors to use "Qo" constraints,
resulting in the better code generation described above. The IO read
accessors are left as-is because ARM64_WORKAROUND_DEVICE_LOAD_ACQUIRE
requires that non-offset register addressing is used, as the LDAR
instruction does not support offset addressing.
When compiling v6.8-rc1 defconfig with GCC 13.2.0, this saves ~4KiB of
text:
| [mark@lakrids:~/src/linux]% ls -al vmlinux-*
| -rwxr-xr-x 1 mark mark 153960576 Jan 23 12:01 vmlinux-after
| -rwxr-xr-x 1 mark mark 153862192 Jan 23 11:57 vmlinux-before
|
| [mark@lakrids:~/src/linux]% size vmlinux-before vmlinux-after
| text data bss dec hex filename
| 26708921 16690350 622736 44022007 29fb8f7 vmlinux-before
| 26704761 16690414 622736 44017911 29fa8f7 vmlinux-after
... though due to internal alignment of sections, this has no impact on
the size of the resulting Image:
| [mark@lakrids:~/src/linux]% ls -al Image-*
| -rw-r--r-- 1 mark mark 43590144 Jan 23 12:01 Image-after
| -rw-r--r-- 1 mark mark 43590144 Jan 23 11:57 Image-before
Aside from the better code generation, there should be no functional
change as a result of this patch. I have lightly tested this patch,
including booting under KVM (where some devices such as PL011 are
emulated).
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20240124111259.874975-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Bring changes from drm-misc-next that got merged in drm-next back to
drm-xe so they can be used for additional features.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Memory errors are an expected occurrence on systems with high memory
density. Generally, errors within a small number of unique physical
locations are acceptable, based on manufacturer and/or admin policy.
During run time, memory with errors may be retired so it is no longer
used by the system. This is done in mm through page poisoning, and the
effect will remain until the system is restarted.
If a memory location is consistently faulty, then the same run time
error handling may occur in the next reboot cycle, leading to
terminating jobs due to that already known bad memory. This could be
prevented if information from the previous boot was not lost.
Some add-in cards with driver-managed memory have on-board persistent
storage. Their driver saves memory error information to the persistent
storage during run time. The information is then restored after reset,
and known bad memory will be retired before the hardware is used.
A running log of bad memory locations is kept across multiple resets.
A similar solution is desirable for CPUs. However, this solution should
leverage industry-standard components as much as possible, rather than
a bespoke platform driver.
Two components are needed: a record format and a persistent storage
interface.
Implement a new module to manage the record formats on persistent
storage. Use the requirements for an AMD MI300-based system to start.
Vendor- and platform-specific details can be abstracted later as needed.
[ bp: Massage commit message and code, squash 30-ish more fixes from
Yazen and me. ]
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Co-developed-by: <naveenkrishna.chatradhi@amd.com>
Signed-off-by: <naveenkrishna.chatradhi@amd.com>
Co-developed-by: <muralidhara.mk@amd.com>
Signed-off-by: <muralidhara.mk@amd.com>
Tested-by: <sathyapriya.k@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240214033516.1344948-3-yazen.ghannam@amd.com
Arm classifies some of its CPU errata as "rare", indicating that the
hardware error is unlikely to occur in practice. Given that the cost of
errata workarounds can often be significant in terms of power and
performance, don't enable workarounds for "rare" errata by default and
update our documentation to reflect that.
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20240209183916.25860-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The patch adding Type-C support for sm6115 was misapplied. All the
orientation switch configuration ended up at the UFS PHY node instead of
the USB PHY node. Move the data bits to the correct place.
Fixes: a06a2f12f9 ("arm64: dts: qcom: qrb4210-rb2: enable USB-C port handling")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240220173104.3052778-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Commit 1fd4a5a36f ("drm/connector: Rename legacy TV property") failed
to update all the users of the struct drm_tv_connector_state mode field,
which resulted in a build failure in i915.
However, a subsequent commit in the same series reintroduced a mode
field in that structure, with a different semantic but the same type,
with the assumption that all previous users were updated.
Since that didn't happen, the i915 driver now compiles, but mixes
accesses to the legacy_mode field and the newer mode field, but with the
previous semantics.
This obviously doesn't work very well, so we need to update the accesses
that weren't in the legacy renaming commit.
Fixes: 1fd4a5a36f ("drm/connector: Rename legacy TV property")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220131251.453060-1-mripard@kernel.org
On some systems, sys_membarrier can be very expensive, causing overall
slowdowns for everything. So put a lock on the path in order to
serialize the accesses to prevent the ability for this to be called at
too high of a frequency and saturate the machine.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-and-tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Fixes: 22e4ebb975 ("membarrier: Provide expedited private command")
Fixes: c5f58bd58f ("membarrier: Provide GLOBAL_EXPEDITED command")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compact 64k PTEs are only intended to be used within a single VMA which
covers the entire 2MB range of the compact 64k PTEs. Add
XE_VMA_PTE_COMPACT VMA flag to indicate compact 64k PTEs are used and
update xe_vma_max_pte_size to return at least 2MB if set.
v2: Include missing changes
Fixes: 8f33b4f054 ("drm/xe: Avoid doing rebinds")
Fixes: c47794bdd6 ("drm/xe: Set max pte size when skipping rebinds")
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/758
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240219211942.3633795-4-matthew.brost@intel.com
Users of the IRQCHIP_PLATFORM_DRIVER_{BEGIN,END} helpers rely on a fwspec
containing only the fwnode (and crucially a number of parameters set to 0)
together with a DOMAIN_BUS_ANY token to check whether a parent irqchip has
probed and registered a domain.
Since de1ff306dc ("genirq/irqdomain: Remove the param count restriction
from select()"), ops->select() is called unconditionally, meaning that
irqchips implementing select() now need to handle ANY as a match.
Instead of adding more esoteric checks to the individual drivers, add that
condition to irq_find_matching_fwspec(), and let it handle the corner case,
as per the comment in the function.
This restores the functionality of the above helpers.
Fixes: de1ff306dc ("genirq/irqdomain: Remove the param count restriction from select()")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20240220114731.1898534-1-maz@kernel.org
Link: https://lore.kernel.org/r/20240219-gic-fix-child-domain-v1-1-09f8fd2d9a8f@linaro.org
The removal of the paremeter count restriction in the core code to allow
pure domain token based select() decisions broke the IMX intmux select
callback as that unconditioally expects that there is a parameter.
Add the missing check for zero parameter count and the token match.
Fixes: de1ff306dc ("genirq/irqdomain: Remove the param count restriction from select()")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/87ttm3ikok.ffs@tglx
- A tqma8mpql device tree fix to correct audio codec iov-supply.
- A couple of USB-C connector DT description revert to fix regression
on imx8mp-dhcom-pdk3 and imx8mn-var-som-symphony board.
- Fix valid range check for imx-weim bus driver.
- Disable UART4 on Data Modul i.MX8M Plus eDM SBC to avoid boot hang
in case that RDC protection is in place.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmXCSosUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7NFQf/TkWrn6KnVCZVufjlYmrgtRyyWa3Q
rjQPNijBupcA9S+hlLDbrtxzv3JeZmZs3VOHitikc7CuAc+WMjZB52VmU1UU6r5i
2irWTy1OauixofZYoC61Yvp/tLLbZCX+O3Y/nCeeBLKxPt3hXNmuILONmnnWeLOH
WigqOqdEm1XP54YSgTFbwTblAJJo+Avot3pJxl8j3CWa/RY9hKGNUzi5z4t1KZmK
X5zKLJA+maR+mM+toGHxvkLu7g6sa74ft16lmGnvAI/l09hrbdwT02q4cLs4jLaD
e29Y0A92bPCWQVsKEcE1Jxj0Fe4pKsYE+6C+MCEQOSqp+jaCJSxhWu7tXA==
=Zs1T
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=y9iD
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.8:
- A tqma8mpql device tree fix to correct audio codec iov-supply.
- A couple of USB-C connector DT description revert to fix regression
on imx8mp-dhcom-pdk3 and imx8mn-var-som-symphony board.
- Fix valid range check for imx-weim bus driver.
- Disable UART4 on Data Modul i.MX8M Plus eDM SBC to avoid boot hang
in case that RDC protection is in place.
* tag 'imx-fixes-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
bus: imx-weim: fix valid range check
Revert "arm64: dts: imx8mn-var-som-symphony: Describe the USB-C connector"
Revert "arm64: dts: imx8mp-dhcom-pdk3: Describe the USB-C connector"
arm64: dts: tqma8mpql: fix audio codec iov-supply
arm64: dts: imx8mp: Disable UART4 by default on Data Modul i.MX8M Plus eDM SBC
Link: https://lore.kernel.org/r/20240206151744.2459-1-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Without the terminator, if a con_id is passed to gpio_find() that
does not exist in the lookup table the function will not stop looping
correctly, and eventually cause an oops.
Cc: stable@vger.kernel.org
Fixes: b2e6355559 ("i2c: gpio: Convert to use descriptors")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20240205102337.439002-1-alexander.sverdlin@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no point in requesting 1 tile on VPU40xx as the FW will
probably need more tiles to run workloads, so it will have to
reconfigure PLL anyway. Don't enable any tiles and allow the FW to
perform initial tile configuration.
This improves NPU boot stability as the tiles are always enabled only
by the FW from the same initial state.
Fixes: 79cdc56c4a ("accel/ivpu: Add initial support for VPU 4")
Cc: stable@vger.kernel.org
Signed-off-by: Andrzej Kacprowski <Andrzej.Kacprowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220131624.1447813-1-jacek.lawrynowicz@linux.intel.com
If the shared_info PFN cache has already been initialized then the content
of the shared_info page needs to be re-initialized whenever the guest
mode is (re)set.
Setting the guest mode is either done explicitly by the VMM via the
KVM_XEN_ATTR_TYPE_LONG_MODE attribute, or implicitly when the guest writes
the MSR to set up the hypercall page.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-12-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
A subsequent patch will allow shared_info to be initialized using either a
GPA or a user-space (i.e. VMM) HVA. To make that patch cleaner, separate
the initialization of the shared_info content from the activation of the
pfncache.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-11-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Some pfncache pages may actually be overlays on guest memory that have a
fixed HVA within the VMM. It's pointless to invalidate such cached
mappings if the overlay is moved so allow a cache to be activated directly
with the HVA to cater for such cases. A subsequent patch will make use
of this facility.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-10-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Rename kvm_is_error_gpa() to kvm_is_gpa_in_memslot() and invert the
polarity accordingly in order to (a) free up kvm_is_error_gpa() to match
with kvm_is_error_{hva,page}(), and (b) to make it more obvious that the
helper is doing a memslot lookup, i.e. not simply checking for INVALID_GPA.
No functional change intended.
Link: https://lore.kernel.org/r/20240215152916.1158-9-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Currently the pfncache page offset is sometimes determined using the gpa
and sometimes the khva, whilst the uhva is always page-aligned. After a
subsequent patch is applied the gpa will not always be valid so adjust
the code to include the page offset in the uhva and use it consistently
as the source of truth.
Also, where a page-aligned address is required, use PAGE_ALIGN_DOWN()
for clarity.
No functional change intended.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-8-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Some code in pfncache uses offset_in_page() but in other places it is open-
coded. Use offset_in_page() consistently everywhere.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-7-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
As noted in [1] the KVM_GUEST_USES_PFN usage flag is never set by any
callers of kvm_gpc_init(), and for good reason: the implementation is
incomplete/broken. And it's not clear that there will ever be a user of
KVM_GUEST_USES_PFN, as coordinating vCPUs with mmu_notifier events is
non-trivial.
Remove KVM_GUEST_USES_PFN and all related code, e.g. dropping
KVM_GUEST_USES_PFN also makes the 'vcpu' argument redundant, to avoid
having to reason about broken code as __kvm_gpc_refresh() evolves.
Moreover, all existing callers specify KVM_HOST_USES_PFN so the usage
check in hva_to_pfn_retry() and hence the 'usage' argument to
kvm_gpc_init() are also redundant.
[1] https://lore.kernel.org/all/ZQiR8IpqOZrOpzHC@google.com
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-6-paul@xen.org
[sean: explicitly call out that guest usage is incomplete]
Signed-off-by: Sean Christopherson <seanjc@google.com>
At the moment pages are marked dirty by open-coded calls to
mark_page_dirty_in_slot(), directly deferefencing the gpa and memslot
from the cache. After a subsequent patch these may not always be set
so add a helper now so that caller will protected from the need to know
about this detail.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-5-paul@xen.org
[sean: decrease indentation, use gpa_to_gfn()]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Sampling gpa and memslot from an unlocked pfncache may yield inconsistent
values so, since there is no problem with calling mark_page_dirty_in_slot()
with the pfncache lock held, relocate the calls in
kvm_xen_update_runstate_guest() and kvm_xen_inject_pending_events()
accordingly.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-4-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
There is no need for the existing kvm_gpc_XXX() functions to be exported.
Clean up now before additional functions are added in subsequent patches.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-3-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
There is a pfncache unmap helper but mapping is open-coded. Arguably this
is fine because mapping is done in only one place, hva_to_pfn_retry(), but
adding the helper does make that function more readable.
No functional change intended.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-2-paul@xen.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEUEC6huC2BN0pvD5fKDiiPnotvG8FAmXUZiITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAoOKI+ei28b8KLB/9MKkUjbbBh9nXezyWdXnulj5jpHWlJ
Xa7Sz7e+Gw5HbpK1/RF3Mb3/uf5D+DTMa2jjUJhezGCugW6ugoFapDC1bJxdafIN
pAZQG/7EYi4TqHEO3/aS5sMh3pISs29COnmHHdQCYfyTMZPKGcDkJuwa7POhHhR1
zrjavD0N2ihBfhoadlT+GQ9QYu+JyWnjrB27hSznsktW9Jeju1u6F9nvOXn60aZU
e7QXgsKe94YXLEed3hj7buPAIirY+tLKIpbw7TtJJwk6EBnnK17S+2wydR0N7yWK
SSsaKJxZCiiaoYkl9chkKTyqh2I3qa/HsxUrFY3TGx5VMhWLiiH/r5eI
=pIjg
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.9-20240220' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2024-02-20
this is a pull request of 9 patches for net-next/master.
The first patch is by Francesco Dolcini and removes a redundant check
for pm_clock_support from the m_can driver.
Martin Hundebøll contributes 3 patches to the m_can/tcan4x5x driver to
allow resume upon RX of a CAN frame.
3 patches by Srinivas Goud add support for ECC statistics to the
xilinx_can driver.
The last 2 patches are by Oliver Hartkopp and me, target the CAN RAW
protocol and fix an error in the getsockopt() for CAN-XL introduced in
the previous pull request to net-next (linux-can-next-for-6.9-20240213).
linux-can-next-for-6.9-20240220
* tag 'linux-can-next-for-6.9-20240220' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: raw: raw_getsockopt(): reduce scope of err
can: raw: fix getsockopt() for new CAN_RAW_XL_VCID_OPTS
can: xilinx_can: Add ethtool stats interface for ECC errors
can: xilinx_can: Add ECC support
dt-bindings: can: xilinx_can: Add 'xlnx,has-ecc' optional property
can: tcan4x5x: support resuming from rx interrupt signal
can: m_can: allow keeping the transceiver running in suspend
dt-bindings: can: tcan4x5x: Document the wakeup-source flag
can: m_can: remove redundant check for pm_clock_support
====================
Link: https://lore.kernel.org/r/20240220085130.2936533-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a checklist is opened, the cursor is rendered in a wrong position
(after the last list element on the screen). You can observe it by
opening any checklist in menuconfig.
Added wmove() to set the cursor in the proper position, just like in
menubox.c. Removed wnoutrefresh(dialog) because dialog window has
already been updated in print_buttons(). Replaced wnoutrefresh(list) and
doupdate() calls with one wrefresh(list) call.
Signed-off-by: Matthew Bystrin <dev.mbstr@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This reverts the following two commits:
- a555bdd0c5 ("Kbuild: enable TRIM_UNUSED_KSYMS again, with some guarding")
- 5cf0fd591f ("Kbuild: disable TRIM_UNUSED_KSYMS option")
Commit 5e9e95cc91 ("kbuild: implement CONFIG_TRIM_UNUSED_KSYMS without
recursion") solved the build time issue.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The programming protocol for the PAT MSR follows the MTRR programming
protocol. However, this protocol is cumbersome and requires disabling
caching (CR0.CD=1), which is not possible on some platforms.
Specifically, a TDX guest is not allowed to set CR0.CD. It triggers
a #VE exception.
It turns out that the requirement to follow the MTRR programming
protocol for PAT programming is unnecessarily strict. The new Intel
Software Developer Manual (http://www.intel.com/sdm) (December 2023)
relaxes this requirement, please refer to the section titled
"Programming the PAT" for more information.
In short, this section provides an alternative PAT update sequence which
doesn't need to disable caches around the PAT update but only to flush
those caches and TLBs.
The AMD documentation does not link PAT programming to MTRR and is there
fore, fine too.
The kernel only needs to flush the TLB after updating the PAT MSR. The
set_memory code already takes care of flushing the TLB and cache when
changing the memory type of a page.
[ bp: Expand commit message. ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240124130650.496056-1-kirill.shutemov@linux.intel.com
On s390, currently kernel uses the '-fPIE' compiler flag for compiling
vmlinux. This has a few problems:
- It uses dynamic symbols (.dynsym), for which the linker refuses to
allow more than 64k sections. This can break features which use
'-ffunction-sections' and '-fdata-sections', including kpatch-build
[1] and Function Granular KASLR.
- It unnecessarily uses GOT relocations, adding an extra layer of
indirection for many memory accesses.
Instead of using '-fPIE', resolve all the relocations at link time and
then manually adjust any absolute relocations (R_390_64) during boot.
This is done by first telling the linker to preserve all relocations
during the vmlinux link. (Note this is harmless: they are later
stripped in the vmlinux.bin link.)
Then use the 'relocs' tool to find all absolute relocations (R_390_64)
which apply to allocatable sections. The offsets of those relocations
are saved in a special section which is then used to adjust the
relocations during boot.
(Note: For some reason, Clang occasionally creates a GOT reference, even
without '-fPIE'. So Clang-compiled kernels have a GOT, which needs to
be adjusted.)
On my mostly-defconfig kernel, this reduces kernel text size by ~1.3%.
[1] https://github.com/dynup/kpatch/issues/1284
[2] https://gcc.gnu.org/pipermail/gcc-patches/2023-June/622872.html
[3] https://gcc.gnu.org/pipermail/gcc-patches/2023-August/625986.html
Compiler consideration:
Gcc recently implemented an optimization [2] for loading symbols without
explicit alignment, aligning with the IBM Z ELF ABI. This ABI mandates
symbols to reside on a 2-byte boundary, enabling the use of the larl
instruction. However, kernel linker scripts may still generate unaligned
symbols. To address this, a new -munaligned-symbols option has been
introduced [3] in recent gcc versions. This option has to be used with
future gcc versions.
Older Clang lacks support for handling unaligned symbols generated
by kernel linker scripts when the kernel is built without -fPIE. However,
future versions of Clang will include support for the -munaligned-symbols
option. When the support is unavailable, compile the kernel with -fPIE
to maintain the existing behavior.
In addition to it:
move vmlinux.relocs to safe relocation
When the kernel is built with CONFIG_KERNEL_UNCOMPRESSED, the entire
uncompressed vmlinux.bin is positioned in the bzImage decompressor
image at the default kernel LMA of 0x100000, enabling it to be executed
in-place. However, the size of .vmlinux.relocs could be large enough to
cause an overlap with the uncompressed kernel at the address 0x100000.
To address this issue, .vmlinux.relocs is positioned after the
.rodata.compressed in the bzImage. Nevertheless, in this configuration,
vmlinux.relocs will overlap with the .bss section of vmlinux.bin. To
overcome that, move vmlinux.relocs to a safe location before clearing
.bss and handling relocs.
Compile warning fix from Sumanth Korikkar:
When kernel is built with CONFIG_LD_ORPHAN_WARN and -fno-PIE, there are
several warnings:
ld: warning: orphan section `.rela.iplt' from
`arch/s390/kernel/head64.o' being placed in section `.rela.dyn'
ld: warning: orphan section `.rela.head.text' from
`arch/s390/kernel/head64.o' being placed in section `.rela.dyn'
ld: warning: orphan section `.rela.init.text' from
`arch/s390/kernel/head64.o' being placed in section `.rela.dyn'
ld: warning: orphan section `.rela.rodata.cst8' from
`arch/s390/kernel/head64.o' being placed in section `.rela.dyn'
Orphan sections are sections that exist in an object file but don't have
a corresponding output section in the final executable. ld raises a
warning when it identifies such sections.
Eliminate the warning by placing all .rela orphan sections in .rela.dyn
and raise an error when size of .rela.dyn is greater than zero. i.e.
Dont just neglect orphan sections.
This is similar to adjustment performed in x86, where kernel is built
with -fno-PIE.
commit 5354e84598 ("x86/build: Add asserts for unwanted sections")
[sumanthk@linux.ibm.com: rebased Josh Poimboeuf patches and move
vmlinux.relocs to safe location]
[hca@linux.ibm.com: merged compile warning fix from Sumanth]
Tested-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: https://lore.kernel.org/r/20240219132734.22881-4-sumanthk@linux.ibm.com
Link: https://lore.kernel.org/r/20240219132734.22881-5-sumanthk@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
This 'relocs' tool is copied from the x86 version, ported for s390, and
greatly simplified to remove unnecessary features.
It reads vmlinux and outputs assembly to create a .vmlinux.relocs_64
section which contains the offsets of all R_390_64 relocations which
apply to allocatable sections.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: https://lore.kernel.org/r/20240219132734.22881-3-sumanthk@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Gcc recently implemented an optimization [1] for loading symbols without
explicit alignment, aligning with the IBM Z ELF ABI. This ABI mandates
symbols to reside on a 2-byte boundary, enabling the use of the larl
instruction. However, kernel linker scripts may still generate unaligned
symbols. To address this, a new -munaligned-symbols option has been
introduced [2] in recent gcc versions.
[1] https://gcc.gnu.org/pipermail/gcc-patches/2023-June/622872.html
[2] https://gcc.gnu.org/pipermail/gcc-patches/2023-August/625986.html
However, when -munaligned-symbols is used in vdso code, it leads to the
following compilation error:
`.data.rel.ro.local' referenced in section `.text' of
arch/s390/kernel/vdso64/vdso64_generic.o: defined in discarded section
`.data.rel.ro.local' of arch/s390/kernel/vdso64/vdso64_generic.o
vdso linker script discards .data section to make it lightweight.
However, -munaligned-symbols in vdso object files references literal
pool and accesses _vdso_data. Hence, compile vdso code without
-munaligned-symbols. This means in the future, vdso code should deal
with alignment of newly introduced unaligned linker symbols.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Link: https://lore.kernel.org/r/20240219132734.22881-2-sumanthk@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
When attempting to boot a kernel compiled with OBJCOPY=llvm-objcopy,
there is a crash right at boot:
Out of memory allocating 6d7800 bytes 8 aligned in range 0:20000000
Reserved memory ranges:
0000000000000000 a394c3c30d90cdaf DECOMPRESSOR
Usable online memory ranges (info source: sclp read info [3]):
0000000000000000 0000000020000000
Usable online memory total: 20000000 Reserved: a394c3c30d90cdaf Free: 0
Call Trace:
(sp:0000000000033e90 [<0000000000012fbc>] physmem_alloc_top_down+0x5c/0x104)
sp:0000000000033f00 [<0000000000011d56>] startup_kernel+0x3a6/0x77c
sp:0000000000033f60 [<00000000000100f4>] startup_normal+0xd4/0xd4
GNU objcopy does not have any issues. Looking at differences between the
object files in each build reveals info.bin does not get properly
populated with llvm-objcopy, which results in an empty .vmlinux.info
section.
$ file {gnu,llvm}-objcopy/arch/s390/boot/info.bin
gnu-objcopy/arch/s390/boot/info.bin: data
llvm-objcopy/arch/s390/boot/info.bin: empty
$ llvm-readelf --section-headers {gnu,llvm}-objcopy/arch/s390/boot/vmlinux | rg 'File:|\.vmlinux\.info|\.decompressor\.syms'
File: gnu-objcopy/arch/s390/boot/vmlinux
[12] .vmlinux.info PROGBITS 0000000000034000 035000 000078 00 WA 0 0 1
[13] .decompressor.syms PROGBITS 0000000000034078 035078 000b00 00 WA 0 0 1
File: llvm-objcopy/arch/s390/boot/vmlinux
[12] .vmlinux.info PROGBITS 0000000000034000 035000 000000 00 WA 0 0 1
[13] .decompressor.syms PROGBITS 0000000000034000 035000 000b00 00 WA 0 0 1
Ulrich points out that llvm-objcopy only copies sections marked as alloc
with a binary output target, whereas the .vmlinux.info section is only
marked as load. Add 'alloc' in addition to 'load', so that both objcopy
implementations work properly:
$ file {gnu,llvm}-objcopy/arch/s390/boot/info.bin
gnu-objcopy/arch/s390/boot/info.bin: data
llvm-objcopy/arch/s390/boot/info.bin: data
$ llvm-readelf --section-headers {gnu,llvm}-objcopy/arch/s390/boot/vmlinux | rg 'File:|\.vmlinux\.info|\.decompressor\.syms'
File: gnu-objcopy/arch/s390/boot/vmlinux
[12] .vmlinux.info PROGBITS 0000000000034000 035000 000078 00 WA 0 0 1
[13] .decompressor.syms PROGBITS 0000000000034078 035078 000b00 00 WA 0 0 1
File: llvm-objcopy/arch/s390/boot/vmlinux
[12] .vmlinux.info PROGBITS 0000000000034000 035000 000078 00 WA 0 0 1
[13] .decompressor.syms PROGBITS 0000000000034078 035078 000b00 00 WA 0 0 1
Closes: https://github.com/ClangBuiltLinux/linux/issues/1996
Link: 3c02cb7492
Suggested-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240216-s390-fix-boot-with-llvm-objcopy-v1-1-0ac623daf42b@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Found and fixed these while working on synchronizing the state
handling of zpci_dev's.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Centralize the removal so all paths are covered and the hotplug slot
will remain active until the device is really destroyed.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
There's a number of tasks that need the state of a zpci device
to be stable. Other tasks need to be synchronized as they change the state.
State changes could be generated by the system as availability or error
events, or be requested by the user through manipulations in sysfs.
Some other actions accessible through sysfs - like device resets - need the
state to be stable.
Unsynchronized state handling could lead to unusable devices. This has
been observed in cases of concurrent state changes through systemd udev
rules and DPM boot control. Some breakage can be provoked by artificial
tests, e.g. through repetitively injecting "recover" on a PCI function
through sysfs while running a "hotplug remove/add" in a loop through a
PCI slot's "power" attribute in sysfs. After a few iterations this could
result in a kernel oops.
So introduce a new mutex "state_lock" to guard the state property of the
struct zpci_dev. Acquire this lock in all task that modify the state:
- hotplug add and remove, through the PCI hotplug slot entry,
- avaiability events, as reported by the platform,
- error events, as reported by the platform,
- during device resets, explicit through sysfs requests or
implict through the common PCI layer.
Break out an inner _do_recover() routine out of recover_store() to
separte the necessary synchronizations from the actual manipulations of
the zpci_dev required for the reset.
With the following changes I was able to run the inject loops for hours
without hitting an error.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Since this guards only the Function Measurement Block, rename from
generic lock to fmb_lock in preparation to introduce another lock
that guards the state member
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
