When DMA is used in RS485 mode make sure that the UARTs tx section is
enabled before the DMA buffers are queued for transmission.
Cc: stable@vger.kernel.org
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240216224709.9928-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit 07c30ea586 ("serial: Do not hold the port lock when setting
rx-during-tx GPIO") the SER_RS485_RX_DURING_TX flag was only set if the
rx-during-tx mode was not controlled by a GPIO. Now the flag is set
unconditionally when RS485 is enabled. This results in an incorrect setting
if the rx-during-tx GPIO is not asserted.
Fix this by setting the flag only if the rx-during-tx mode is not
controlled by a GPIO and thus restore the correct behaviour.
Cc: stable@vger.kernel.org # 6.6+
Fixes: 07c30ea586 ("serial: Do not hold the port lock when setting rx-during-tx GPIO")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240216224709.9928-1-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new SBI console has the same problem as the old one: there's only
one shared backing hardware and no synchronization, so the two drivers
end up stepping on each other. This was the same issue the old SBI-0.1
console drivers had, but that was disabled by default when SBI-0.1 was.
So just mark the new driver as nonportable.
Reported-by: Emil Renner Berthing <kernel@esmil.dk>
Fixes: 88ead68e76 ("tty: Add SBI debug console support to HVC SBI driver")
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240214153429.16484-2-palmer@rivosinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The am642-evm doesn't allow to enable 2 x CPSW3g ports and 2 x ICSSG1 ports
all together, so base k3-am642-evm.dts enables by default 2 x CPSW3g ports
and 1 x ICSSG1 ports, but it is also possible to support 1 x CPSW3g ports
and 2 x ICSSG1 ports configuration.
This patch adds overlay to support 1 x CPSW3g ports and 2 x ICSSG1 ports
configuration:
- Add label name 'mdio_mux_1' for 'mdio-mux-1' node so that the node
'mdio-mux-1' can be disabled in the overlay using the label name.
- disable 2nd CPSW3g port
- update CPSW3g pinmuxes to not use RGMII2
- disable mdio-mux-1 and define mdio-mux-2 to route ICSSG1 MDIO to the
shared DP83869 PHY
- add and enable ICSSG1 RGMII2 pinmuxes
- enable ICSSG1 MII1 port
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-4-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Stop calling drm_bridge_remove() for bridges allocated/managed by other
drivers in the remove paths of meson_encoder_{cvbs,dsi,hdmi}.
drm_bridge_remove() unregisters the bridge so it cannot be used
anymore. Doing so for bridges we don't own can lead to the video
pipeline not being able to come up after -EPROBE_DEFER of the VPU
because we're unregistering a bridge that's managed by another driver.
The other driver doesn't know that we have unregistered it's bridge
and on subsequent .probe() we're not able to find those bridges anymore
(since nobody re-creates them).
This fixes probe errors on Meson8b boards with the CVBS outputs enabled.
Fixes: 09847723c1 ("drm/meson: remove drm bridges at aggregate driver unbind time")
Fixes: 42dcf15f90 ("drm/meson: add DSI encoder")
Cc: <stable@vger.kernel.org>
Reported-by: Steve Morvai <stevemorvai@hotmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Steve Morvai <stevemorvai@hotmail.com>
Link: https://lore.kernel.org/r/20240215220442.1343152-1-martin.blumenstingl@googlemail.com
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240215220442.1343152-1-martin.blumenstingl@googlemail.com
I am no longer involved in Type-C development and not really current on its
status and progress. Recently I have been doing more damage than good.
It is time to go.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240215202039.1982539-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Note that pmz_detach() is only called once pmz_attach() was successfully
called. In that case platform_set_drvdata() was called and so
platform_get_drvdata() won't return NULL. This allows to drop the
respective check and so get rid of the only error path in pmz_detach().
After that the driver can be trivially converted from always returning
zero in the remove callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/90b9a65ad8800b4d047aa5219959008a01588a94.1708246007.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/60d0657daf8f4f9e2e3e282941ba542f08dc7f96.1708246007.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/f2ad92c97086c42dab23cdb165d9f978bbf3d3b5.1708246007.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This general note about time_* functions is also useful to be available in
kernel documentation. Therefore transform it into a kernel-doc DOC block
with proper formatting.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240123164702.55612-6-anna-maria@linutronix.de
timer_base struct lacks description of struct members. Important struct
member information is sprinkled in comments or in code all over the place.
Collect information and write struct description to keep track of most
important information in a single place.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240123164702.55612-5-anna-maria@linutronix.de
The return value of tick_nohz_next_event() is not obvious at the first
glance. Add a kernel-doc compatible function description which also covers
return values.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240123164702.55612-4-anna-maria@linutronix.de
Documentation of functions lacks the annotations which are used by
kernel-doc and *.rst to make appearance in rendered documents more
user-friendly.
Use those annotations to improve user-friendliness. While at it prevent
duplication of comments and use a reference instead.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240123164702.55612-3-anna-maria@linutronix.de
hrtimer base related struct definitions are part of hrtimers.h as it is
required there. With this, also the struct documentation which is for core
code internal use, is exposed into the general api.
To prevent this, move all core internal definitions and the related
includes into hrtimer_defs.h.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240123164702.55612-2-anna-maria@linutronix.de
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
usb_device_type, usb_if_device_type, usb_ep_device_type and
usb_port_device_type variables to be constant structures as well, placing
it into read-only memory which can not be modified at runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-4-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the gadget_type
variable to be a constant structure as well, placing it into read-only
memory which can not be modified at runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-3-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
usb_phy_dev_type variable to be a constant structure as well, placing it
into read-only memory which can not be modified at runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-2-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move all the
device_type variables in use by the driver to be constant structures as
well, placing it into read-only memory which can not be modified at
runtime.
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Link: https://lore.kernel.org/r/20240218-device_cleanup-usb-v1-1-77423c4da262@marliere.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed sometimes when tethering is used over NCM with Windows 11
as host, at some instances, the gadget_giveback has one byte appended at
the end of a proper NTB. When the NTB is parsed, unwrap call looks for
any leftover bytes in SKB provided by u_ether and if there are any pending
bytes, it treats them as a separate NTB and parses it. But in case the
second NTB (as per unwrap call) is faulty/corrupt, all the datagrams that
were parsed properly in the first NTB and saved in rx_list are dropped.
Adding a few custom traces showed the following:
[002] d..1 7828.532866: dwc3_gadget_giveback: ep1out:
req 000000003868811a length 1025/16384 zsI ==> 0
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb toprocess: 1025
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb seq: 0xce67
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x400
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb ndp_len: 0x10
[002] d..1 7828.532869: ncm_unwrap_ntb: K: Parsed NTB with 1 frames
In this case, the giveback is of 1025 bytes and block length is 1024.
The rest 1 byte (which is 0x00) won't be parsed resulting in drop of
all datagrams in rx_list.
Same is case with packets of size 2048:
[002] d..1 7828.557948: dwc3_gadget_giveback: ep1out:
req 0000000011dfd96e length 2049/16384 zsI ==> 0
[002] d..1 7828.557949: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.557950: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x800
Lecroy shows one byte coming in extra confirming that the byte is coming
in from PC:
Transfer 2959 - Bytes Transferred(1025) Timestamp((18.524 843 590)
- Transaction 8391 - Data(1025 bytes) Timestamp(18.524 843 590)
--- Packet 4063861
Data(1024 bytes)
Duration(2.117us) Idle(14.700ns) Timestamp(18.524 843 590)
--- Packet 4063863
Data(1 byte)
Duration(66.160ns) Time(282.000ns) Timestamp(18.524 845 722)
According to Windows driver, no ZLP is needed if wBlockLength is non-zero,
because the non-zero wBlockLength has already told the function side the
size of transfer to be expected. However, there are in-market NCM devices
that rely on ZLP as long as the wBlockLength is multiple of wMaxPacketSize.
To deal with such devices, it pads an extra 0 at end so the transfer is no
longer multiple of wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240205074650.200304-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reverted commit makes the state machine only ever go from SRC_ATTACH_WAIT
to SNK_TRY in endless loop when toggling. After revert it goes to SRC_ATTACHED
after initially trying SNK_TRY earlier, as it should for toggling to ever detect
the power source mode and the port is again able to provide power to attached
power sinks.
This reverts commit 2d6d801270.
Cc: stable@vger.kernel.org
Fixes: 2d6d801270 ("usb: typec: tcpm: reset counter when enter into unattached state after try role")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217162023.1719738-1-megi@xff.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When upgrading from 6.1 LTS to 6.6 LTS, I noticed the ethernet gadget
stopped working on Palm TE.
Commit 8825acd7cc ("ARM: omap1: remove dead code") deleted Palm TE from
machine_without_vbus_sense(), although the board is still used. Fix that.
Fixes: 8825acd7cc ("ARM: omap1: remove dead code")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240217192042.GA372205@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
829 if (request->complete) {
830 spin_unlock(&priv_dev->lock);
831 usb_gadget_giveback_request(&priv_ep->endpoint,
832 request);
833 spin_lock(&priv_dev->lock);
834 }
835
836 if (request->buf == priv_dev->zlp_buf)
837 cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
Driver append an additional zero packet request when queue a packet, which
length mod max packet size is 0. When transfer complete, run to line 831,
usb_gadget_giveback_request() will free this requestion. 836 condition is
true, so cdns3_gadget_ep_free_request() free this request again.
Log:
[ 1920.140696][ T150] BUG: KFENCE: use-after-free read in cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.140696][ T150]
[ 1920.151837][ T150] Use-after-free read at 0x000000003d1cd10b (in kfence-#36):
[ 1920.159082][ T150] cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.164988][ T150] cdns3_transfer_completed+0x438/0x5f8 [cdns3]
Add check at line 829, skip call usb_gadget_giveback_request() if it is
additional zero length packet request. Needn't call
usb_gadget_giveback_request() because it is allocated in this driver.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240202154217.661867-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility that usb_role_switch device is unregistered before
the user put usb_role_switch. In this case, the user may still want to
get/set_role() since the user can't sense the changes of usb_role_switch.
This will add a flag to show if usb_role_switch is already registered and
avoid unwanted behaviors.
Fixes: fde0aa6c17 ("usb: common: Small class for USB role switches")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current design, usb role class driver will get usb_role_switch parent's
module reference after the user get usb_role_switch device and put the
reference after the user put the usb_role_switch device. However, the
parent device of usb_role_switch may be removed before the user put the
usb_role_switch. If so, then, NULL pointer issue will be met when the user
put the parent module's reference.
This will save the module pointer in structure of usb_role_switch. Then,
we don't need to find module by iterating long relations.
Fixes: 5c54fcac9a ("usb: roles: Take care of driver module reference counting")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cadence have several controllers from 0x000403xx family but current
driver suuport detecting only one with DID equal 0x0004034E.
It causes that if someone uses different CDNSP controller then driver
will use incorrect version and register space.
Patch fix this issue.
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240215121609.259772-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
host.c file has some parts of code that were introduced for CDNS3 driver
and should not be used with CDNSP driver.
This patch blocks using these parts of codes by CDNSP driver.
These elements include:
- xhci_plat_cdns3_xhci object
- cdns3 specific XECP_PORT_CAP_REG register
- cdns3 specific XECP_AUX_CTRL_REG1 register
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240206104018.48272-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local helper function to compare the given pair of cycle count
evaluates them. If the left value is less than the right value, the
function returns negative value.
If the safe cycle is less than the current cycle, it is the case of
cycle lost. However, it is not currently handled properly.
This commit fixes the bug.
Cc: <stable@vger.kernel.org>
Fixes: 705794c53b ("ALSA: firewire-lib: check cycle continuity")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20240218033026.72577-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Miglia Technology ships Harmony Audio 2004. It uses Oxford Semiconductor
OXFW970 for communication function in IEEE 1394 bus. This commit adds
support for the model.
In my opinion, the firmware of ASIC is really the initial stage, since
it has the following quirks.
* It skips several isochronous cycles to transmit isochronous packets
when receiving any asynchronous transaction.
* The value of dbc field in the transmitted packet is the number of
accumulated quadlets in CIP payload, instead of the accumulated data
blocks. Furthermore, the value includes the quadlets of CIP payload in
the packet.
* It neither supports AV/C Stream Format Information command nor AV/C
Extended Stream Format Information command.
* The vendor and model information in root directory of configuration
ROM includes some mistakes.
Additionally, when operating at 96.0 kHz, it often skips much isochronous
cycles to transmit the isochronous packets. The issue is detected as cycle
discontinuity and ALSA PCM application receives -EIO at any operation for
PCM substream. I have never found any workaround yet.
$ config-rom-pretty-printer < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
1024 04249e04 bus_info_length 4, crc_length 36, crc 40452
1028 31333934 bus_name "1394"
1032 20ff5003 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 5 (64)
1036 0030e002 company_id 0030e0 |
1040 00454647 device_id 8594474567 | EUI-64 13757098081207879
root directory
-----------------------------------------------------------------
1044 00062d69 directory_length 6, crc 11625
1048 030030e0 vendor
1052 8100000a --> descriptor leaf at 1092
1056 1700f970 model
1060 81000011 --> descriptor leaf at 1128
1064 0c0083c0 node capabilities: per IEEE 1394
1068 d1000001 --> unit directory at 1072
unit directory at 1072
-----------------------------------------------------------------
1072 00046ff9 directory_length 4, crc 28665 (should be 43676)
1076 1200a02d specifier id
1080 13010001 version
1084 1700f970 model
1088 8100000f --> descriptor leaf at 1148
descriptor leaf at 1092
-----------------------------------------------------------------
1092 00085f8a leaf_length 8, crc 24458
1096 00000000 textual descriptor
1100 00000000 minimal ASCII
1104 4d69676c "Migl"
1108 69612054 "ia T"
1112 6563686e "echn"
1116 6f6c6f67 "olog"
1120 79204c74 "y Lt"
1124 642e0000 "d."
descriptor leaf at 1128
-----------------------------------------------------------------
1128 00040514 leaf_length 4, crc 1300
1132 00000000 textual descriptor
1136 00000000 minimal ASCII
1140 4f584657 "OXFW"
1144 20393730 " 970"
descriptor leaf at 1148
-----------------------------------------------------------------
1148 0005a1dc leaf_length 5, crc 41436
1152 00000000 textual descriptor
1156 00000000 minimal ASCII
1160 4861726d "Harm"
1164 6f6e7941 "onyA"
1168 7564696f "udio"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20240218074128.95210-5-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Miglia Harmony Audio (OXFW970) has a quirk to put the number of
accumulated quadlets in CIP payload into the dbc field of CIP header.
This commit handles the quirk in the packet processing layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20240218074128.95210-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Miglia Harmony Audio does neither support AV/C Stream Format Information
command nor AV/C Extended Stream Format Information command.
This commit adds a workaround for the case and uses the hard-coded formats.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20240218074128.95210-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes relying upon linux/of_platform.h to include
linux/platform_device.h, which it no longer does, thereby fixing
compilation problems like:
In file included from drivers/usb/host/uhci-hcd.c:850:
drivers/usb/host/uhci-grlib.c: In function 'uhci_hcd_grlib_probe':
drivers/usb/host/uhci-grlib.c:92:29: error: invalid use of undefined type 'struct platform_device'
92 | struct device_node *dn = op->dev.of_node;
| ^~
Fixes: ef175b29a2 ("of: Stop circularly including of_device.h and of_platform.h")
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20240129075056.1511630-1-andreas@gaisler.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The servers for the @codeaurora domain have long been retired and any
messages sent there will bounce. Fix Odelu's address in the binding to
match the .mailmap entry so that folks see the correct address when
looking at the documentation.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240202181748.4124411-1-quic_jhugo@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
ICSSG1 provides dual Gigabit Ethernet support with proper FW loaded.
The ICSSG1 MII0 (RGMII1) has DP83869 PHY attached to it. The ICSSG1 shares
MII1 (RGMII2) PHY DP83869 with CPSW3g and it's assigned by default to
CPSW3g. The MDIO access to MII1 (RGMII2) PHY DP83869 is controlled by MDIO
bus switch and also assigned to CPSW3g. Therefore the ICSSG1 MII1 (RGMII2)
port is kept disable and ICSSG1 is enabled in single MAC mode by
default.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-3-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The ICSSG IP on AM64x SoCs have two Industrial Ethernet Peripherals (IEPs)
to manage/generate Industrial Ethernet functions such as time stamping.
Each IEP sub-module is sourced from an internal clock mux that can be
derived from either of the IP instance's ICSSG_IEP_GCLK or from another
internal ICSSG CORE_CLK mux. Add both the IEP nodes for both the ICSSG
instances. The IEP clock is currently configured to be derived
indirectly from the ICSSG_ICLK running at 250 MHz.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-2-danishanwar@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add a mechanism for named attribute_groups to hide their directory at
sysfs_update_group() time, or otherwise skip emitting the group
directory when the group is first registered. It piggybacks on
is_visible() in a similar manner as SYSFS_PREALLOC, i.e. special flags
in the upper bits of the returned mode. To use it, specify a symbol
prefix to DEFINE_SYSFS_GROUP_VISIBLE(), and then pass that same prefix
to SYSFS_GROUP_VISIBLE() when assigning the @is_visible() callback:
DEFINE_SYSFS_GROUP_VISIBLE($prefix)
struct attribute_group $prefix_group = {
.name = $name,
.is_visible = SYSFS_GROUP_VISIBLE($prefix),
};
SYSFS_GROUP_VISIBLE() expects a definition of $prefix_group_visible()
and $prefix_attr_visible(), where $prefix_group_visible() just returns
true / false and $prefix_attr_visible() behaves as normal.
The motivation for this capability is to centralize PCI device
authentication in the PCI core with a named sysfs group while keeping
that group hidden for devices and platforms that do not meet the
requirements. In a PCI topology, most devices will not support
authentication, a small subset will support just PCI CMA (Component
Measurement and Authentication), a smaller subset will support PCI CMA +
PCIe IDE (Link Integrity and Encryption), and only next generation
server hosts will start to include a platform TSM (TEE Security
Manager).
Without this capability the alternatives are:
* Check if all attributes are invisible and if so, hide the directory.
Beyond trouble getting this to work [1], this is an ABI change for
scenarios if userspace happens to depend on group visibility absent any
attributes. I.e. this new capability avoids regression since it does
not retroactively apply to existing cases.
* Publish an empty /sys/bus/pci/devices/$pdev/tsm/ directory for all PCI
devices (i.e. for the case when TSM platform support is present, but
device support is absent). Unfortunate that this will be a vestigial
empty directory in the vast majority of cases.
* Reintroduce usage of runtime calls to sysfs_{create,remove}_group()
in the PCI core. Bjorn has already indicated that he does not want to
see any growth of pci_sysfs_init() [2].
* Drop the named group and simulate a directory by prefixing all
TSM-related attributes with "tsm_". Unfortunate to not use the naming
capability of a sysfs group as intended.
In comparison, there is a small potential for regression if for some
reason an @is_visible() callback had dependencies on how many times it
was called. Additionally, it is no longer an error to update a group
that does not have its directory already present, and it is no longer a
WARN() to remove a group that was never visible.
Link: https://lore.kernel.org/all/2024012321-envious-procedure-4a58@gregkh/ [1]
Link: https://lore.kernel.org/linux-pci/20231019200110.GA1410324@bhelgaas/ [2]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/2024013028-deflator-flaring-ec62@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 27c5fd271d ("RDMA/hns: The UD mode can only be configured
with DCQCN") adds a check of congest control alorithm for UD. But
that patch causes a problem: hr_dev->caps.congest_type is global,
used by all QPs, so modifying this field to DCQCN for UD QPs causes
other QPs unable to use any other algorithm except DCQCN.
Revert the modification in commit 27c5fd271d ("RDMA/hns: The UD
mode can only be configured with DCQCN"). Add a new field cong_type
to struct hns_roce_qp and configure DCQCN for UD QPs.
Fixes: 27c5fd271d ("RDMA/hns: The UD mode can only be configured with DCQCN")
Fixes: f91696f2f0 ("RDMA/hns: Support congestion control type selection according to the FW")
Signed-off-by: Luoyouming <luoyouming@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240219061805.668170-1-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmXSbvkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGi3kH/iM5AcKeQfee07to
TJP3WORLBt5UrUMgAQbJdNAruCj6brHA6YnZ6AjdhdNZ41RO06h69kTpb+y/CYJz
+ogGK5qhWsC8ETM6rJCioo8uI4GU70p84fGiMfLw8o6vUvmtyI5qH3531Y30Edxt
qqMVtQrVe9J5JcHQjJ/mQo8nAuvZdQQGM90zLGqFP+JheP3CzsCokraIITqoebDC
PCVAsnSbXT/uMjwSr03kdnMnnY++fxz/TyHb/QRMPq/4xU8nz0Z2hlOOYrVkOINu
lkIYtCDGTk0QR3hdDiO9yt+k1OsWi+oBkrhjAQmAk9x3riiXq1NKvZZLDArt7PH5
gSyo9sE=
=h5Ei
-----END PGP SIGNATURE-----
Merge 6.8-rc5 into driver-core-next
We need the driver core changes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move bus-width property to *main.dtsi, above the OTAP/ITAP
delay values. While there is no error with where it is
currently at, it is easier to read the MMC node if the
bus-width property is located above the OTAP/ITAP delay
values consistently across MMC nodes.
Add missing bus-width for MMC2 in k3-am62-main.
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-9-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Move ti,clkbuf-sel property above the OTAP/ITAP delay values.
While there is no error with where it is currently at, it is
easier to read the MMC node if ti,clkbuf-sel is located above
the OTAP/ITAP delay values consistently across MMC nodes.
Add missing ti,clkbuf-sel for MMC0 in k3-am64-main.
Signed-off-by: Judith Mendez <jm@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240213235701.2438513-8-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
