Stefan Mätje <stefan.maetje@esd.eu> says:
The purpose of this patch is to introduce a new CAN driver to support
the esd GmbH 402 family of CAN interface boards. The hardware design
is based on a CAN controller implemented in a FPGA attached to a
PCIe link.
More information on these boards can be found following the links
included in the commit message.
This patch supports all boards but will operate the CAN-FD capable
boards only in Classic-CAN mode. The CAN-FD support will be added
when the initial patch has stabilized.
The patch is reuses the previous work of my former colleague:
Link: https://lore.kernel.org/linux-can/1426592308-23817-1-git-send-email-thomas.koerper@esd.eu
The patch is based on the linux-can-next main branch.
Changed in v11:
No functional, only editorial changes due to feedback on v10.
- Make lifetime of macros used for hardware timestamp calculation
very short by #undef-ing them after use.
- Fixed insertion order of new entry in MAINTAINERS file.
Changed in v10:
Most changes due to feedback by Vincent Mailhol
https://lore.kernel.org/linux-can/CAMZ6RqLOAC930GNOU+pWuoi6FgYwFOuFrSyAzVjvE2fuVgy8oA@mail.gmail.com
- Add support for ethtool operations by using default operations
provided by the can_dev module for drivers with hardware time
stamp support.
- Factor out core unregistration into pci402_unregister_core().
- Factor out getting next TX fifo index into acc_tx_fifo_next().
- Stop counting alloc_can_err_skb() failures in rx_dropped statistic.
- Add CAN_ERR_CNT flag in CAN error frames as needed.
- Rework function acc_reset_fpga(). To clear I^2C bus enable bit
is not necessary after FPGA reset.
- Simplify struct acc_bmmsg_rxtxdone layout.
- Additional non functional changes due to feedback by Vincent
- Some spelling corrections: ESDACC -> esdACC
Changes in v9:
- Fix returning success error code in case of allocation failure in
pci402_probe().
Changes in v8:
- Rebased to 6.6-rc2 on linux-can-next branch main
Changes in v7:
- Numerous changes. Find the quoted with inline comments about changes
below after the changes list. Stuff that I don't understand and
where I have questions is marked with ????.
Unfortunately I will be AFK till 28th of November.
Changes in v6:
- Fixed the statistic handling of RX overrun errors and increase
net_device_stats::rx_errors instead of net_device_stats::rx_dropped.
- Added a patch to not increase rx statistics when generating a CAN
rx error message frame as suggested on the linux-can list.
- Added a patch to not not increase rx_bytes statistics for RTR frames
as suggested on the linux-can list.
The last two patches change the statistics handling from the previous
style used in other drivers to the newly suggested one.
Changes in v5:
- Added the initialization for netdev::dev_port as it is implemented
for another CAN driver. See
https://lore.kernel.org/linux-can/20211026180553.1953189-1-mailhol.vincent@wanadoo.fr
Changes in v4:
- Fixed the build failure on ARCH=arm64 that was found by the Intel
kernel test robot. See
https://lore.kernel.org/linux-can/202109120608.7ZbQXkRh-lkp@intel.com
Removed error monitoring code that used GCC's built-in compiler
functions for atomic access (__sync_* functions). GCC versions
after 9 (tested with "gcc-10 (Ubuntu 10.3.0-1ubuntu1~20.04)")
don't implement the intrinsic atomic as in-line code but call
"__aarch64_ldadd4_acq_rel" on arm64. This GCC support function
is not exported by the kernel and therefore the module build
post-processing fails.
Removed that code because the error monitoring never showed a
problem during the development this year.
Changes in v3:
- Rework the bus-off restart logic in acc_set_mode() and
handle_core_msg_errstatechange() to call netif_wake_queue() from the
error active event.
- Changed pci402_init_card() to allocate a variable sized array of
struct acc_core using devm_kcalloc() instead of using a fixed size
array in struct pci402_card.
- Changed handle_core_msg_txabort() to release aborted TX frames in
TX FIFO order.
- Fixed the acc_close() function to abort all pending TX request in
esdACC controller.
- Fixed counting of transmit aborts in handle_core_msg_txabort().
It is now done like in can_flush_echo_skb().
- Fixed handle_core_msg_buserr() to create error frames including the
CAN RX and TX error counters that were missing.
- Fixed acc_set_bittiming() neither to touch LOM mode setting of
esdACC controller nor to enter or leave RESET mode.
The esdACC controller is going active on the CAN bus in acc_open()
and is going inactive (RESET mode) again in acc_close().
- Rely on the automatic release of memory fetched by devm_kzalloc().
But still use devm_irq_free() explicitely to make sure that the
interrupt handler is disconnected at that point.
This avoids a possible crash in non-MSI mode due to the IRQ
triggered by another device on the same PCI IRQ line.
- Changed to use DMA map API instead of pci_*_consistent compatibility
wrappers.
- Fixed stale email references and updated copyright information.
- Removed any traces of future CAN-FD support.
Changes in v2:
- Avoid warning triggered by -Wshift-count-overflow on architectures
with 32-bit dma_addr_t.
- Fixed Makefile not to build the kernel module always. Doing this
renamed esd402_pci.c to esd_402_pci-core.c as recommended by Marc.
previous versions:
v1 - https://lore.kernel.org/linux-can/20210728203647.15240-1-Stefan.Maetje@esd.eu
v2 - https://lore.kernel.org/linux-can/20210730173805.3926-1-Stefan.Maetje@esd.eu
v3 - https://lore.kernel.org/linux-can/20210908164640.23243-1-stefan.maetje@esd.eu
v4 - https://lore.kernel.org/linux-can/20210916172152.5127-1-stefan.maetje@esd.eu
v5 - https://lore.kernel.org/linux-can/20211109155326.2608822-1-stefan.maetje@esd.eu
v6 - https://lore.kernel.org/linux-can/20211201220328.3079270-1-stefan.maetje@esd.eu
v7 - https://lore.kernel.org/linux-can/20221106224156.3619334-1-stefan.maetje@esd.eu
v8 - https://lore.kernel.org/linux-can/20231025141635.1459606-1-stefan.maetje@esd.eu
v9 - https://lore.kernel.org/linux-can/20231107184103.2802678-1-stefan.maetje@esd.eu
v10 - https://lore.kernel.org/linux-can/20231120175657.4070921-1-stefan.maetje@esd.eu
Link: https://lore.kernel.org/all/20231122160211.2110448-1-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the PCI based PCIe/402 CAN interface family
from esd GmbH that is available with various form factors
(https://esd.eu/en/products/402-series-can-interfaces).
All boards utilize a FPGA based CAN controller solution developed
by esd (esdACC). For more information on the esdACC see
https://esd.eu/en/products/esdacc.
This driver detects all available CAN interface board variants of
the family but atm. operates the CAN-FD capable devices in
Classic-CAN mode only! A later patch will introduce the CAN-FD
functionality in this driver.
Co-developed-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://lore.kernel.org/all/20231122160211.2110448-3-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adding myself (Stefan Mätje) as a maintainer for the upcoming driver of
the PCIe/402 interface card family.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://lore.kernel.org/all/20231122160211.2110448-2-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add __pm_runtime_put_autosuspend() that replaces
pm_runtime_put_autosuspend() for new users. The intent is to later
re-purpose pm_runtime_put_autosuspend() to also mark the device's last
busy stamp---which is what the vast majority of users actually need.
This is also described in pm_runtime_put_autosuspend() documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two ways to opportunistically increment a device's runtime PM
usage count, calling either pm_runtime_get_if_active() or
pm_runtime_get_if_in_use(). The former has an argument to tell whether to
ignore the usage count or not, and the latter simply calls the former with
ign_usage_count set to false. The other users that want to ignore the
usage_count will have to explicitly set that argument to true which is a
bit cumbersome.
To make this function more practical to use, remove the ign_usage_count
argument from the function. The main implementation is in a static
function called pm_runtime_get_conditional() and implementations of
pm_runtime_get_if_active() and pm_runtime_get_if_in_use() are moved to
runtime.c.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Takashi Iwai <tiwai@suse.de> # sound/
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> # drivers/accel/ivpu/
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> # drivers/gpu/drm/i915/
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci/
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ISO15765-2 standard supports to take the PDUs communication parameters
blocksize (BS) and Separation Time minimum (STmin) either from the first
received flow control (FC) "static" or from every received FC "dynamic".
Add a new CAN_ISOTP_DYN_FC_PARMS flag to support dynamic FC parameters.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20231208165729.3011-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN RAW sockets allow userspace to tell if a received CAN frame comes
from the same socket, another socket on the same host, or another host.
See commit 1e55659ce6 ("can-raw: add msg_flags to distinguish local
traffic"). However, this feature is missing in CAN BCM sockets.
Add the same feature to CAN BCM sockets. When reading a received frame
(opcode RX_CHANGED) using recvmsg, two flags in msg->msg_flags may be
set following the previous convention (from CAN RAW), to distinguish
between 'own', 'local' and 'remote' CAN traffic.
Update the documentation to reflect this change.
Signed-off-by: Nicolas Maier <nicolas.maier.dev@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20240120081018.2319-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
10ms is too high for today's hardware, even low end ones. This default
end up being used a lot on Arm machines at least. Pine64, mac mini and
pixel 6 all end up with 10ms rate_limit_us when using schedutil, and
it's too high for all of them.
Change the default to 2ms which should be 'pessimistic' enough for worst
case scenario, but not too high for platforms with fast DVFS hardware.
Signed-off-by: Qais Yousef <qyousef@layalina.io>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NVM command set 1.0 (or later) mandates PI to be in the last bytes of
metadata. But this was not supported in the block-layer, and driver
registered a nop profile.
Since block-integrity can now handle flexible PI offset, change the
driver to support this configuration.
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240201130126.211402-4-joshi.k@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Block layer integrity processing assumes that protection information
(PI) is placed in the first bytes of each metadata block.
Remove this limitation and include the metadata before the PI in the
calculation of the guard tag.
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Chinmay Gameti <c.gameti@samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240201130126.211402-3-joshi.k@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Allow computation using the existing guard value.
This is a prep patch.
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240201130126.211402-2-joshi.k@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that all callers pass in GFP_KERNEL to blkdev_zone_mgmt() and use
memalloc_no{io,fs}_{save,restore}() to define the allocation scope, we can
drop the gfp_mask parameter from blkdev_zone_mgmt() as well as
blkdev_zone_reset_all() and blkdev_zone_reset_all_emulated().
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Link: https://lore.kernel.org/r/20240128-zonefs_nofs-v3-5-ae3b7c8def61@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Guard the calls to blkdev_zone_mgmt() with a memalloc_nofs scope.
This helps us getting rid of the GFP_NOFS argument to blkdev_zone_mgmt();
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20240128-zonefs_nofs-v3-4-ae3b7c8def61@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a memalloc_nofs scope around all calls to blkdev_zone_mgmt(). This
allows us to further get rid of the GFP_NOFS argument for
blkdev_zone_mgmt().
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20240128-zonefs_nofs-v3-3-ae3b7c8def61@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Guard the calls to blkdev_zone_mgmt() with a memalloc_noio scope.
This helps us getting rid of the GFP_NOIO argument to blkdev_zone_mgmt();
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Mike Snitzer <snitzer@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240128-zonefs_nofs-v3-2-ae3b7c8def61@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass GFP_KERNEL instead of GFP_NOFS to the blkdev_zone_mgmt() call in
zonefs_zone_mgmt().
As as zonefs_zone_mgmt() and zonefs_inode_zone_mgmt() are never called
from a place that can recurse back into the filesystem on memory reclaim,
it is save to call blkdev_zone_mgmt() with GFP_KERNEL.
Link: https://lore.kernel.org/all/ZZcgXI46AinlcBDP@casper.infradead.org/
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240128-zonefs_nofs-v3-1-ae3b7c8def61@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the function amd_pstate_adjust_perf(), the 'min_perf' variable is set
to 'highest_perf' instead of 'lowest_perf'.
Fixes: 1d215f0319 ("cpufreq: amd-pstate: Add fast switch function for AMD P-State")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Tor Vic <torvic9@mailbox.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: 6.1+ <stable@vger.kernel.org> # 6.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since WiFi 7 is expected to support MLO, so we should enable MAC-0/1 and
PHY-0/1. By default, set dbcc_en=true, change quota to DBCC mode, and set
MLO mode to 2 + 0 that means we only use 2x2 connection on MAC/PHY-0
for now.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-12-pkshih@realtek.com
Reference the current quota mode to avoid misleading warnings.
This patch is required after supporting DBCC quota mode.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-11-pkshih@realtek.com
Modify reg for BE generation when AP stop, otherwise have warning
messages "Polling beacon packet empty fail".
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-10-pkshih@realtek.com
ctrl_nbtg_bt_tx is used to control AGC settings under non-shared path
condition, which is affected by BT TX. To speed up IO, merge continual
bit mask into one IO. Also, correct a register definition.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-9-pkshih@realtek.com
When there are OBSS that cannot interpret 26-tone RU transmissions,
we should disable 26-tone RU HE TB PPDU transmissions. So, add registers
accordingly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-8-pkshih@realtek.com
Hardware can use spatial reuse to reduce interference in OBSS environment,
and originally use MAC header to match BSS color and AID. Change to use
PLCP to match them earlier to prevent margin timing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-7-pkshih@realtek.com
Consider mac_idx as an argument to set this register to disable QoS NULL
update MUEDCA timer.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-5-pkshih@realtek.com
DLE (data link engine) could hold quota when we are going to enable/disable
MAC-1 block, so trigger hardware to return all held quota.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-4-pkshih@realtek.com
We are going to support MLO/DBCC, so need to load parameter table to
PHY-1 as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-3-pkshih@realtek.com
PHY-1 can be seen as a copy of PHY-0, and the difference is their base
register address, so add a function to get offset to access PHY-1.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240209065229.34515-2-pkshih@realtek.com
In 'brcmf_cfg80211_start_ap()', not assume that
NL80211_HIDDEN_SSID_NOT_IN_USE is zero but prefer
an explicit check instead. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Alexey Berezhok <a@bayrepo.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240208085121.2430-1-a@bayrepo.ru
struct mwifiex_ie_types_chan_list_param_set::chan_scan_param is treated
as a flexible array, so convert it into one so that it doesn't trip
the array bounds sanitizer[1]. Only a few places were using sizeof()
on the whole struct, so adjust those to follow the calculation pattern
to avoid including the trailing single element.
Examining binary output differences doesn't appear to show any literal
size values changing, though it is obfuscated a bit by the compiler
adjusting register usage and stack spill slots, etc.
Link: https://github.com/KSPP/linux/issues/51 [1]
Cc: Brian Norris <briannorris@chromium.org>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Dmitry Antipov <dmantipov@yandex.ru>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: zuoqilin <zuoqilin@yulong.com>
Cc: Ruan Jinjie <ruanjinjie@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240207103024.make.423-kees@kernel.org
Document
ATWILC1000/ATWILC3000
Baremetal Wi-Fi/BLE Link Controller Software Design Guide
https://tinyurl.com/yer2xhyc
says that bit 0 of the CRC7 code must always be a 1.
I confirmed that today with a logic analyzer: setting bit 0 causes
wilc1000 to accept a command with CRC7 enabled, whereas clearing bit 0
causes wilc1000 to reject the command with a CRC error.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240207050736.2717641-1-davidm@egauge.net
During mac80211 reconfig, chanctx ops of multiple channels might not
be called in order as normal cases. However, we expect the first active
chanctx always to be put at our sub entity index 0. So, if it does not,
we do a swap there. Besides, reconfig won't allocate a new chanctx object.
So, we should reset the reference count when ops add chanctx.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240206030624.23382-7-pkshih@realtek.com
After MLO, we will need to consider not only active chanctx but also active
interfaces (roles) to decide entity things. So in advance, we move handling
from chanctx_ops::add/remove to chanctx_ops::assign_vif/unassign_vif. Then,
we can recalculate and aware active interfaces' changes.
For now, behavior should not be really different, since active chanctx and
active interface are one-to-one mapping before MLO.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240206030624.23382-6-pkshih@realtek.com
Originally, we consider weight only based on how many chanctxs that
mac80211 sets. However, we need to consider both active chanctxs and
active interfaces to distinguish MCC (multiple channel concurrent)
from impending MLO.
Although the logic of handling is extended, for now, behavior might
not be different under current condition.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240206030624.23382-5-pkshih@realtek.com
Originally, we just declared two sub-entity, and according to rolling
down mechanism, we ensured that index 0 contained sub-entity as long
as there are sub-entity. So, we could use for-loop after deciding the
last index.
But, we are preparing to expand num of sub-entity for MLO. Then, there
won't be just two sub-entity. And, there might be holes between two bits
in the bitmap. So, we cannot simply do for-loop as before. Instead, we
need to follow the set bits.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240206030624.23382-4-pkshih@realtek.com
Originally, we replaced sub-entity of index 0 with another one in some
cases. However, we will need a swap here in following implementations.
So, we introduce it ahead and change code from replacing to swapping.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240206030624.23382-3-pkshih@realtek.com
Some of our calculation during concurrent mode depend on last beacon
TSF. Originally, we just set IEEE80211_HW_TIMING_BEACON_ONLY and get
what we want from mac80211. But, IEEE80211_HW_TIMING_BEACON_ONLY will
be restricted once we declare MLO.
Since we are about to consider the MLO stuffs, so sync beacon TSF by
ourselves now and unset IEEE80211_HW_TIMING_BEACON_ONLY.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240206030624.23382-2-pkshih@realtek.com
WILC driver currently applies some default configuration whenever the firmware
is initialized, and sets the default preamble size to short. However, despite
this passed option, firmware is also able to successfully connect to access
points only using long preamble, so this setting does not really enforce short
preambles and is misleading regarding applied configuration.
Update default configuration and make it match the firmware behavior by passing
the existing WILC_FW_PREAMBLE_AUTO value (2 instead of 0). The updated setting
does not really alter firmware behavior since it is still capable to connect to
both short preamble and long preamble access points, but at list the setting now
expresses for real the corresponding firmware behavior.
More info: it has been implemented to address the transmission (Tx) blackout
issue observed in the 802.11b mode. The modification has no impact on the other
modes, which will continue to work as they did in the previous implementation.
This change will allow the 802.11b transmission (2, 5.5, 11Mbps) to use long
preamble.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240115-wilc_1000_fixes-v1-1-54d29463a738@bootlin.com
Use convenient 'kstrtou32_from_user()' in 'mwifiex_verext_write()'
and 'kstrtobool_from_user()' in 'mwifiex_timeshare_coex_write()',
respectively. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240110115314.421298-1-dmantipov@yandex.ru
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZcoMdAAKCRCRxhvAZXjc
ogy4AQDVp4huR6BBnRMhOCZbIsmkuHmq6ynpIZNTTAM0DdMn5AEAlJ03aEIaG9WS
RQMdaYajeVpZfR/vIUg8UdVkHQxOEgw=
=akNF
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.8-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- Fix performance regression introduced by moving the security
permission hook out of do_clone_file_range() and into its caller
vfs_clone_file_range().
This causes the security hook to be called in situation were it
wasn't called before as the fast permission checks were left in
do_clone_file_range().
Fix this by merging the two implementations back together and
restoring the old ordering: fast permission checks first, expensive
ones later.
- Tweak mount_setattr() permission checking so that mount properties on
the real rootfs can be changed.
When we added mount_setattr() we added additional checks compared to
legacy mount(2). If the mount had a parent then verify that the
caller and the mount namespace the mount is attached to match and if
not make sure that it's an anonymous mount.
But the real rootfs falls into neither category. It is neither an
anoymous mount because it is obviously attached to the initial mount
namespace but it also obviously doesn't have a parent mount. So that
means legacy mount(2) allows changing mount properties on the real
rootfs but mount_setattr(2) blocks this. This causes regressions (See
the commit for details).
Fix this by relaxing the check. If the mount has a parent or if it
isn't a detached mount, verify that the mount namespaces of the
caller and the mount are the same. Technically, we could probably
write this even simpler and check that the mount namespaces match if
it isn't a detached mount. But the slightly longer check makes it
clearer what conditions one needs to think about.
* tag 'vfs-6.8-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs: relax mount_setattr() permission checks
remap_range: merge do_clone_file_range() into vfs_clone_file_range()
The conversion to kvcalloc() mixed up the object size and count
arguments, causing a warning:
drivers/gpu/drm/nouveau/nouveau_svm.c: In function 'nouveau_svm_fault_buffer_ctor':
drivers/gpu/drm/nouveau/nouveau_svm.c:1010:40: error: 'kvcalloc' sizes specified with 'sizeof' in the earlier argument and not in the later argument [-Werror=calloc-transposed-args]
1010 | buffer->fault = kvcalloc(sizeof(*buffer->fault), buffer->entries, GFP_KERNEL);
| ^
drivers/gpu/drm/nouveau/nouveau_svm.c:1010:40: note: earlier argument should specify number of elements, later size of each element
The behavior is still correct aside from the warning, but fixing it avoids
the warnings and can help the compiler track the individual objects better.
Fixes: 71e4bbca07 ("nouveau/svm: Use kvcalloc() instead of kvzalloc()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212112230.1117284-1-arnd@kernel.org
I have no time for this, but since it looks like I'm the main
contributor for the last few years to the subsystem, I'll take
it for now. Geert agreed to help me as a designated reviewer.
Let's see how it will go...
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Move the switch_to() implementation to process.c and use the generic
switch_to.h header file instead, like some other architectures.
This addresses also the oddity that the old switch_to() implementation
assigns the return value of __switch_to() to 'prev' instead of 'last',
like it should.
Remove also all includes of switch_to.h from C files, except process.c.
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
save_access_regs() and restore_access_regs() are only available by
including switch_to.h. This is done by a couple of C files, which have
nothing to do with switch_to(), but only need these functions.
Move both functions to a new header file and improve the implementation:
- Get rid of typedef
- Add memory access instrumentation support
- Use long displacement instructions lamy/stamy instead of lam/stam - all
current users end up with better code because of this
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
During the cache sync test we verify that values we expect to have been
written only to the cache do not appear in the hardware. This works most
of the time but since we randomly generate both the original and new values
there is a low probability that these values may actually be the same.
Wrap get_random_bytes() to ensure that the values are different, there
are other tests which should have similar verification that we actually
changed something.
While we're at it refactor the test to use three changed values rather
than attempting to use one of them twice, that just complicates checking
that our new values are actually new.
We use random generation to try to avoid data dependencies in the tests.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://msgid.link/r/20240211-regmap-kunit-random-change-v3-1-e387a9ea4468@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the driver core can properly handle constant struct bus_type,
move the acpi_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We describe tplg_file_name and drv_name using snd_sof_of_mach
array and select correct machine description based on dts compatible
string.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://msgid.link/r/20240212125258.420265-1-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Intel Lunar Lake-M PCI ID to the driver list of supported devices.
This is the same controller found in previous generations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://msgid.link/r/20240212082027.2462849-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MCSPI controller have few limitations regarding the transaction
size when the FIFO buffer is enabled and the WCNT feature is used
to find the end of word, in this case if WCNT is not a multiple of
the FIFO Almost Empty Level (AEL), then the FIFO empty event is not
generated correctly. In addition to this limitation, few other unknown
sequence of events that causes the FIFO empty status to not reflect the
exact status were found when FIFO is being used without DMA enabled
during extended testing in AM65x platform. Till the exact root cause
is found and fixed, revert the FIFO support without DMA.
See J721E Technical Reference Manual (SPRUI1C), section 12.1.5
for further details: http://www.ti.com/lit/pdf/spruil1
This reverts commit 75223bbea8 ("spi: omap2-mcspi: Add FIFO support
without DMA")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://msgid.link/r/20240212120049.438495-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The MeeGoPad T8 uses the standard rt5645 jd_mode=3 setting for jack-detect,
but the used jack connector outputs an inverted jack-detect signal.
Add a DMI quirk for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20240211212736.179605-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
