Remove all zero MAC address entries (00:00:00:00:00:00) from a multicast
packet's tracker TVLV before transmitting it and update all headers
accordingly. This way, instead of keeping the multicast packet at a
constant size throughout its journey through the mesh, it will become
more lightweight, smaller with every interested receiver on the way and
on each splitting intersection. Which can save some valuable bandwidth.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Implement the preparation of a batman-adv multicast packet and use this
under certain conditions.
For one thing this implements the capability to push a complete
batman-adv multicast packet header, including a tracker TVLV with all
originator destinations that have signaled interest in it, onto a given
ethernet frame with an IP multicast packet inside.
For another checks are implemented to determine if encapsulating a
multicast packet in this new batman-adv multicast packet type and using
it is feasible. Those checks are:
1) Have all nodes signaled that they are capable of handling the new
batman-adv multicast packet type?
2) Do all active hard interfaces of all nodes, including us, have an MTU
of at least 1280 bytes?
3) Does a complete multicast packet header with all its destination
addresses fit onto the given multicast packet / ethernet frame and
does not exceed 1280 bytes?
If all checks passed then the new batman-adv multicast packet type will
be used for transmission and distribution. Otherwise we fall back to one or
more batman-adv unicast packet transmissions, if possible. Or if not
possible we will fall back to classic flooding through a batman-adv
broadcast packet.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Implement functionality to receive and forward a new TVLV capable
multicast packet type.
The new batman-adv multicast packet type allows to contain several
originator destination addresses within a TVLV. Routers on the way will
potentially split the batman-adv multicast packet and adjust its tracker
TVLV contents.
Routing decisions are still based on the selected BATMAN IV or BATMAN V
routing algorithm. So this new batman-adv multicast packet type retains
the same loop-free properties.
Also a new OGM multicast TVLV flag is introduced to signal to other
nodes that we are capable of handling a batman-adv multicast packet and
multicast tracker TVLV. And that all of our hard interfaces have an MTU
of at least 1280 bytes (IPv6 minimum MTU), as a simple solution for now
to avoid MTU issues while forwarding.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This version will contain all the (major or even only minor) changes for
Linux 6.8.
The version number isn't a semantic version number with major and minor
information. It is just encoding the year of the expected publishing as
Linux -rc1 and the number of published versions this year (starting at 0).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
On failure to parse parameters in ovl_parse_param_lowerdir(), it is
necessary to update ctx->nr with the correct nr before using
ovl_reset_lowerdirs() to release l->name.
Reported-and-tested-by: syzbot+26eedf3631650972f17c@syzkaller.appspotmail.com
Fixes: c835110b58 ("ovl: remove unused code in lowerdir param parsing")
Co-authored-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
ChunHao Lin says:
====================
r8169: fix DASH devices network lost issue
This series are used to fix network lost issue on systems that support
DASH. It has been tested on rtl8168ep and rtl8168fp.
====================
Link: https://lore.kernel.org/r/20231109173400.4573-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Device that support DASH may be reseted or powered off during suspend.
So driver needs to handle DASH during system suspend and resume. Or
DASH firmware will influence device behavior and causes network lost.
Fixes: b646d90053 ("r8169: magic.")
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: ChunHao Lin <hau@realtek.com>
Link: https://lore.kernel.org/r/20231109173400.4573-3-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For devices that support DASH, even DASH is disabled, there may still
exist a default firmware that will influence device behavior.
So driver needs to handle DASH for devices that support DASH, no
matter the DASH status is.
This patch also prepares for "fix network lost after resume on DASH
systems".
Fixes: ee7a1beb97 ("r8169:call "rtl8168_driver_start" "rtl8168_driver_stop" only when hardware dash function is enabled")
Cc: stable@vger.kernel.org
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20231109173400.4573-2-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Walleij says:
====================
Fix large frames in the Gemini ethernet driver
This is the result of a bug hunt for a problem with the
RTL8366RB DSA switch leading me wrong all over the place.
I am indebted to Vladimir Oltean who as usual pointed
out where the real problem was, many thanks!
Tryig to actually use big ("jumbo") frames on this
hardware uncovered the real bugs. Then I tested it on
the DSA switch and it indeed fixes the issue.
To make sure it also works fine with big frames on
non-DSA devices I also copied a large video file over
scp to a device with maximum frame size, the data
was transported in large TCP packets ending up in
0x7ff sized frames using software checksumming at
~2.0 MB/s.
If I set down the MTU to the standard 1500 bytes so
that hardware checksumming is used, the scp transfer
of the same file was slightly lower, ~1.8-1.9 MB/s.
Despite this not being the best test it shows that
we can now stress the hardware with large frames
and that software checksum works fine.
v3: https://lore.kernel.org/r/20231107-gemini-largeframe-fix-v3-0-e3803c080b75@linaro.org
v2: https://lore.kernel.org/r/20231105-gemini-largeframe-fix-v2-0-cd3a5aa6c496@linaro.org
v1: https://lore.kernel.org/r/20231104-gemini-largeframe-fix-v1-0-9c5513f22f33@linaro.org
====================
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-0-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RX max frame size is over 10000 for the Gemini ethernet,
but the TX max frame size is actually just 2047 (0x7ff after
checking the datasheet). Reflect this in what we offer to Linux,
cap the MTU at the TX max frame minus ethernet headers.
We delete the code disabling the hardware checksum for large
MTUs as netdev->mtu can no longer be larger than
netdev->max_mtu meaning the if()-clause in gmac_fix_features()
is never true.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-3-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Gemini ethernet controller provides hardware checksumming
for frames up to 1514 bytes including ethernet headers but not
FCS.
If we start sending bigger frames (after first bumping up the MTU
on both interfaces sending and receiving the frames), truncated
packets start to appear on the target such as in this tcpdump
resulting from ping -s 1474:
23:34:17.241983 14:d6:4d:a8:3c:4f (oui Unknown) > bc:ae:c5:6b:a8:3d (oui Unknown),
ethertype IPv4 (0x0800), length 1514: truncated-ip - 2 bytes missing!
(tos 0x0, ttl 64, id 32653, offset 0, flags [DF], proto ICMP (1), length 1502)
OpenWrt.lan > Fecusia: ICMP echo request, id 1672, seq 50, length 1482
If we bypass the hardware checksumming and provide a software
fallback, everything starts working fine up to the max TX MTU
of 2047 bytes, for example ping -s2000 192.168.1.2:
00:44:29.587598 bc:ae:c5:6b:a8:3d (oui Unknown) > 14:d6:4d:a8:3c:4f (oui Unknown),
ethertype IPv4 (0x0800), length 2042:
(tos 0x0, ttl 64, id 51828, offset 0, flags [none], proto ICMP (1), length 2028)
Fecusia > OpenWrt.lan: ICMP echo reply, id 1683, seq 4, length 2008
The bit enabling to bypass hardware checksum (or any of the
"TSS" bits) are undocumented in the hardware reference manual.
The entire hardware checksum unit appears undocumented. The
conclusion that we need to use the "bypass" bit was found by
trial-and-error.
Since no hardware checksum will happen, we slot in a software
checksum fallback.
Check for the condition where we need to compute checksum on the
skb with either hardware or software using == CHECKSUM_PARTIAL instead
of != CHECKSUM_NONE which is an incomplete check according to
<linux/skbuff.h>.
On the D-Link DIR-685 router this fixes a bug on the conduit
interface to the RTL8366RB DSA switch: as the switch needs to add
space for its tag it increases the MTU on the conduit interface
to 1504 and that means that when the router sends packages
of 1500 bytes these get an extra 4 bytes of DSA tag and the
transfer fails because of the erroneous hardware checksumming,
affecting such basic functionality as the LuCI web interface.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-2-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enumerator 3 is 1548 bytes according to the datasheet.
Not 1542.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-1-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As I was working on a syzbot report, I found that KCSAN would
probably complain that reading q->head or q->tail without
barriers could lead to invalid results.
Add corresponding READ_ONCE() and WRITE_ONCE() to avoid
load-store tearing.
Fixes: d94ba80ebb ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20231109174859.3995880-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 8a4f030dbc.
Richard says:
The test itself is harmless, but keeping it will make people think,
"oh this pointer can be invalid."
In fact the core stack ensures that ioctl() can't be invoked after
release(), otherwise Bad Stuff happens.
Fixes: 8a4f030dbc ("ptp: Fixes a null pointer dereference in ptp_ioctl")
Link: https://lore.kernel.org/all/ZVAf_qdRfDAQYUt-@hoboy.vegasvil.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We've rarely been seeing a nonce offset inconsistency that doesn't show
up in tests: this adds some extra verification code to the data update
path that prints out more relevant info when it occurs.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
We really don't want to be invoking memory reclaim with btree locks
held: even aside from (solvable, but tricky) recursion issues, it can
cause painful to diagnose performance edge cases.
This fixes a recently reported issue in btree_key_can_insert_cached().
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Reported-by: Mateusz Guzik <mjguzik@gmail.com>
Fixes: https://lore.kernel.org/linux-bcachefs/CAGudoHEsb_hGRMeWeXh+UF6po0qQuuq_NKSEo+s1sEb6bDLjpA@mail.gmail.com/T/
As prep work for the next patch to fix a key cache reclaim issue, we
need to start tracking whether we're currently holding write locks - so
that we can release and retake the before calling into memory reclaim.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The btree key cache maintains lists of items that have been freed, but
can't yet be reclaimed because a bch2_trans_relock() call might find
them - we're waiting for SRCU readers to release.
Previously, we wouldn't count these items against the number we're
attempting to scan for, which would mean we'd evict more live key cache
entries - doing quite a bit of potentially unecessary work.
With recent work to make sure we don't hold SRCU locks for too long, it
should be safe to count all the items on the freelists against number to
scan - even if we can't reclaim them yet, we will be able to soon.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
We can't create stripes if we don't have enough devices - this
manifested as an integer underflow bug later.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
bch2_btree_iter_peek_node() can return a NULL ptr (when the tree is
shorter than the search depth); handle this with an early return.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: https://lore.kernel.org/linux-bcachefs/5fc3c28b-c232-4ec7-b0ac-4ef220ddf976@moroto.mountain/T/
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Transform zero-length array `entries` into a proper flexible-array
member in `struct journal_seq_blacklist_table`; and fix the following
-Warray-bounds warnings:
fs/bcachefs/journal_seq_blacklist.c:148:26: warning: array subscript idx is outside array bounds of 'struct journal_seq_blacklist_table_entry[0]' [-Warray-bounds=]
fs/bcachefs/journal_seq_blacklist.c:150:30: warning: array subscript idx is outside array bounds of 'struct journal_seq_blacklist_table_entry[0]' [-Warray-bounds=]
fs/bcachefs/journal_seq_blacklist.c:154:27: warning: array subscript idx is outside array bounds of 'struct journal_seq_blacklist_table_entry[0]' [-Warray-bounds=]
fs/bcachefs/journal_seq_blacklist.c:176:27: warning: array subscript i is outside array bounds of 'struct journal_seq_blacklist_table_entry[0]' [-Warray-bounds=]
fs/bcachefs/journal_seq_blacklist.c:177:27: warning: array subscript i is outside array bounds of 'struct journal_seq_blacklist_table_entry[0]' [-Warray-bounds=]
fs/bcachefs/journal_seq_blacklist.c:297:34: warning: array subscript i is outside array bounds of 'struct journal_seq_blacklist_table_entry[0]' [-Warray-bounds=]
fs/bcachefs/journal_seq_blacklist.c:298:34: warning: array subscript i is outside array bounds of 'struct journal_seq_blacklist_table_entry[0]' [-Warray-bounds=]
fs/bcachefs/journal_seq_blacklist.c:300:31: warning: array subscript i is outside array bounds of 'struct journal_seq_blacklist_table_entry[0]' [-Warray-bounds=]
This results in no differences in binary output.
This helps with the ongoing efforts to globally enable -Warray-bounds.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Transform zero-length array `s` into a proper flexible-array
member in `struct snapshot_table` via the DECLARE_FLEX_ARRAY()
helper; and fix tons of the following -Warray-bounds warnings:
fs/bcachefs/snapshot.h:36:21: warning: array subscript <unknown> is outside array bounds of 'struct snapshot_t[0]' [-Warray-bounds=]
fs/bcachefs/snapshot.h:36:21: warning: array subscript <unknown> is outside array bounds of 'struct snapshot_t[0]' [-Warray-bounds=]
fs/bcachefs/snapshot.c:135:70: warning: array subscript <unknown> is outside array bounds of 'struct snapshot_t[0]' [-Warray-bounds=]
fs/bcachefs/snapshot.h:36:21: warning: array subscript <unknown> is outside array bounds of 'struct snapshot_t[0]' [-Warray-bounds=]
fs/bcachefs/snapshot.h:36:21: warning: array subscript <unknown> is outside array bounds of 'struct snapshot_t[0]' [-Warray-bounds=]
fs/bcachefs/snapshot.h:36:21: warning: array subscript <unknown> is outside array bounds of 'struct snapshot_t[0]' [-Warray-bounds=]
This helps with the ongoing efforts to globally enable -Warray-bounds.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The bch2_target_to_text_sb are not used outside the file disk_groups.c,
so the modification is defined as static.
fs/bcachefs/disk_groups.c:583:6: warning: no previous prototype for ‘bch2_target_to_text_sb’.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=7144
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
This is a follow up to:
commit b8e3a87a62 ("bpf: Add crosstask check to __bpf_get_stack").
This test ensures that the task iterator only gets a single
user stack (for the current task).
Signed-off-by: Jordan Rome <linux@jordanrome.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20231112023010.144675-1-linux@jordanrome.com
From Jani:
The drm_print.[ch] facilities use very few pr_*() calls directly. The
users of pr_*() calls do not necessarily include <drm/drm_print.h> at
all, and really don't have to.
Even the ones that do include it, usually have <linux/...> includes
first, and <drm/...> includes next. Notably, <linux/kernel.h> includes
<linux/printk.h>.
And, of course, <linux/printk.h> defines pr_fmt() itself if not already
defined.
No, it's encouraged not to use pr_*() at all, and prefer drm device
based logging, or device based logging.
This reverts commit 36245bd02e.
Signed-off-by: Luben Tuikov <ltuikov89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/878r75wzm9.fsf@intel.com
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231111024130.11464-2-ltuikov89@gmail.com
Add support for using Timer 1 (i225/i226 have 4 timer registers) as a
free-running clock (the "cycles" clock) in addition to Timer 0 (the
default, "adjustable clock"). The objective is to allow taprio/etf
offloading to coexist with PTP vclocks.
Besides the implementation of .getcyclesx64() for i225/i226, to keep
timestamping working when vclocks are in use, we also need to add
support for TX and RX timestamping using the free running timer, when
the requesting socket is bound to a vclock.
On the RX side, i225/i226 can be configured to store the values of two
timers in the received packet metadata area, so it's a matter of
configuring the right registers and retrieving the right timestamp.
The TX is a bit more involved because the hardware stores a single
timestamp (with the selected timer in the TX descriptor) into one of
the timestamp registers.
Note some changes at how the timestamps are done for RX, the
conversion and adjustment of timestamps are now done closer to the
consumption of the timestamp instead of near the reception.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We can re-use the IGC_SET_FLAG() macro to simplify setting some values
in the TX data descriptor. With the macro it's easier to get the
meaning of the operations.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove extra check after condition, add check after generating key
for encryption. The check is needed to return non zero rc before
rewriting it with generating key for decryption.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Fixes: d70e9fa558 ("cifs: try opening channels after mounting")
Signed-off-by: Ekaterina Esina <eesina@astralinux.ru>
Co-developed-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
"host=" should start with ';' (as in cifs_get_spnego_key)
So its length should be 6.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Fixes: 7c9c3760b3 ("[CIFS] add constants for string lengths of keynames in SPNEGO upcall string")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Co-developed-by: Ekaterina Esina <eesina@astralinux.ru>
Signed-off-by: Ekaterina Esina <eesina@astralinux.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
When the kernel code has changed the build may ask for configuration
input and hang. Prevent this and instead use the default settings.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
ACP7.0 based platform legacy drivers can be built by selecting
necessary kernel config option. This patch enables build support
of the same.
Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com>
Link: https://lore.kernel.org/r/20231113123345.2196504-1-Syed.SabaKareem@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5650 is I2S codec integrated with HP and SPK.
The HW board connects SoC I2S to RT5650 codec as below:
I2S0: ALC5650 aif1 for Speaker
I2S2: ALC5650 aif2 for Headphone
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231113115907.18539-1-mac.chiang@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Bit 6 of INPPGA (INPPGAMUTE) does not control the Aux path, it controls
the input PGA path, as can been seen from Figure 8 Input Boost Stage in
the datasheet. Update the naming of things in the driver to match this
and update the routing to also reflect this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231113155916.1741027-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rebuilding CP VSI each time the PR is created drastically increase the
time of maximum VFs creation. Add function to reserve number of CP
queues to deal with this problem.
Use the same function to decrease number of queues in case of removing
VFs. Assume that caller of ice_eswitch_reserve_cp_queues() will also
call ice_eswitch_attach/detach() correct number of times.
Still one by one PR adding is handy for VF resetting routine.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is no need to use specific functions for rebuilding path. Let's
use current implementation by removing all representors and as the
result remove switchdev environment.
It will be added in devices rebuild path. For example during adding VFs,
port representors for them also will be created.
Rebuild control plane VSI before removing representors with INIT_VSI
flag set to reinit VSI in hardware after reset.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement adding representors one by one. Always set switchdev
environment when first representor is being added and clear environment
when last one is being removed.
Basic switchdev configuration remains the same. Code related to creating
and configuring representor was changed.
Instead of setting whole representors in one function handle only one
representor in setup function. The same with removing representors.
Stop representors when new one is being added or removed. Stop means,
disabling napi, stopping traffic and removing slow path rule. It is
needed because ::q_id will change after remapping, so each representor
will need new rule.
When representor are stopped rebuild control plane VSI with one more or
one less queue. One more if new representor is being added, one less if
representor is being removed.
Bridge port is removed during unregister_netdev() call on PR, so there
is no need to call it from driver side.
After that do remap new queues to correct vector. At the end start all
representors (napi enable, start queues, add slow path rule).
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously only case when queues amount is lower was covered. Implement
realloc for case when queues amount is higher than previous one. Use
krealloc() function and zero new allocated elements.
It has to be done before ice_vsi_def_cfg(), because stats element for
ring is set there.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is needed to track correct Tx topology. Update it every time new
representor is created or remove node in case of removing corresponding
representor.
Still clear all node when removing switchdev mode as part of Tx topology
isn't related only to representors. Also clear ::rate_note value to
prevent skipping this node next time Tx topology is created.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement mechanism to change number of queues for SWITCHDEV_CTRL VSI
type.
Value from ::req_txq/rxq will be written to ::alloc_txq/rxq after
calling ice_vsi_rebuild().
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In follow up patches it will be easier to obtain created port
representor pointer instead of the id. Without it the pattern from
eswitch side will look like:
- create PR
- get PR based on the id
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Representor code needs to be independent from specific device type, like
in this case VF. Make generic add / remove representor function and
specific add VF / rem VF function. New device types will follow this
scheme.
In bridge offload code there is a need to get representor pointer based
on VSI. Implement helper function to achieve that.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make eswitch code generic by removing VF pointer reference in functions.
It is needed to support eswitch mode for other type of devices.
Previously queue id used for Rx was based on VF number. Use ::q_id saved
in port representor instead.
After adding or removing port representor ::q_id value can change. It
isn't good idea to iterate over representors list using this value.
Use xa_find starting from the first one instead to get next port
representor to remap.
The number of port representors has to be equal to ::num_rx/tx_q. Warn if
it isn't true.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of assuming that each VF has pointer to port representor save it
in xarray. It will allow adding port representor for other device types.
Drop reference to VF where it is use only to get port representor. Get
it from xarray instead.
The functions will no longer by specific for VF, rename them.
Track id assigned by xarray in port representor structure. The id can't
be used as ::q_id, because it is fixed during port representor lifetime.
::q_id can change after adding / removing other port representors.
Side effect of removing VF pointer is that we are losing VF MAC
information used in unrolling. Store it in port representor as parent
MAC.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Extract repr from vf->repr as it is often use in the ice_repr_rem().
Remove meaningless clearing of q_vector and netdev pointers as kfree is
called on repr pointer.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
