Fix misalignment between structures names and their kdoc in hw.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20231011074301.223879-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In debugging platform or firmware related MEI-PXP connection
issues, having a timeout when clients (such as i915) calling
into mei-pxp's send/receive functions have proven useful as opposed to
blocking forever until the kernel triggers a watchdog panic (when
platform issues are experienced).
Update the mei-pxp component interface send and receive functions
to take in timeouts.
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20231011110157.247552-5-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable and enable mei-pxp client on errors to clean the internal state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20231011110157.247552-4-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under memory pressure recv fails due to kmalloc failure,
and if drivers(pxp) retry send/receive, send blocks
indefinitely.
Send without recv leaves the channel in a bad state.
Retry send attempt after small timeout and reset the channel if
the retry failed on kmalloc failure too.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20231011110157.247552-3-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add variation of the send and recv functions on bus
that define timeout.
Caller can use such functions in flow that can stuck
to bail out and not to put down the whole system.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20231011110157.247552-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are DT properties that can be shared across different Solomon OLED
Display Controller families. Split them into a separate common schema to
avoid these properties to be duplicated in different DT bindings schemas.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231014071520.1342189-6-javierm@redhat.com
The Solomon SSD132x controllers (such as the SSD1322, SSD1325 and SSD1327)
are used by 16 grayscale dot matrix OLED panels, extend the driver to also
support this chip family.
Instead adding an indirection level to allow the same modesetting pipeline
to be used by both controller families, add another pipeline for SSD132x.
This leads to some code duplication but it makes the driver easier to read
and reason about. Once other controller families are added (e.g: SSD133x),
some common code can be factored out in driver helpers to be shared by the
different families. But that can be done later once these patterns emerge.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231014071520.1342189-5-javierm@redhat.com
This deemed useful to avoid hardcoding a page height and allow to support
other Solomon controller families, but dividing the screen in pages seems
to be something that is specific to the SSD130x chip family.
For example, SSD132x chip family divides the screen in segments (columns)
and common outputs (rows), so the concept of screen pages does not exist
for the SSD132x family.
Let's drop this field from the device info struct and just use a constant
SSD130X_PAGE_HEIGHT macro to define the page height. While being there,
replace hardcoded 8 values in places where it is used as the page height.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20231014071520.1342189-2-javierm@redhat.com
Using struct gpio_chip is not safe as it will disappear if the
underlying driver is unbound for any reason. Switch to using reference
counted struct gpio_device and its dedicated accessors.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Dipen Patel <dipenp@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[andy: used gpio_device_find_by_fwnode()]
Reviewed-by: Dipen Patel <dipenp@nvidia.com>
Link: https://lore.kernel.org/r/20231010151709.4104747-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add the required nodes to enable the DisplayPort interface, connected
to the Embedded DisplayPort port, where we have an internal display.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230816190427.2137768-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the DSI display found on the Sony Xperia M5, including
the necessary regulators configuration for it.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721082822.680010-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the relevant nodes for display backlight on Sony Xperia M5: this
needs both the SoC PWM IP and MT6332 PMIC LED strings.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721082822.680010-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Introduce all nodes for all of the display blocks in the MediaTek Helio
X10 MT6795 SoC, including the DSI PHY and DSI/DPI interfaces: those are
left disabled as usage is board specific.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721082822.680010-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a devicetree for rev4 of Spherion. It uses the rt5682s audio codec
instead of the rt5682 used in the previous revision.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721201705.387426-6-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a devicetree for rev5-sku2 of Hayato. It uses the rt5682s audio
codec instead of the rt5682 used in the previous revision.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721201705.387426-5-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There aren't enough users of the common asurada-audio dtsi files to
justify having them. It is simpler to just have the audio nodes directly
on the board files.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721201705.387426-4-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add binding for newer version of Google Spherion (Acer Chromebook 514):
rev4.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721201705.387426-3-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add binding for newer version of Google Hayato: rev5-sku2.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230721201705.387426-2-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add iommu support in the SoC DTS using the 4 local arbiters (LARBs)
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-7-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Local arbiter (LARB) is a component of Smart Multimedia Interface (SMI),
used to help the memory management (IOMMU).
This patch add 4 LARBs and 2 clocks for the larb1 and larb3 support.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-6-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Smart Multimedia Interface (SMI) local arbiter does the arbitration for
memory requests from multi-media engines. Add SMI in the MT8365 DTS will
allow to add local ARBiter (LARB), use by IOMMU.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-5-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
AI Processor Unit System (APUSYS) is a highly efficient computing unit
system which is most suitable for AI/CV algorithms. It includes one
programmable AI processor (Cadence VP6) for both AI and CV algorithms,
and an eDMA engine for data movement between external DRAM and VP6
internal memory.
For more detail, ask Mediatek for the MT8365 IoT application processor
functional specification.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-3-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Camera System (CamSys) incorporates an enhanced feature based image
signal processor to connect a variety of image sensor components. This
processor consists of timing generated unit (TG), lens/sensor
compensation unit and image process unit.
For more detail, ask Mediatek for the MT8365 IoT application processor
functional specification.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-2-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Multimedia subsystem (MMsys) contains multimedia controller, Multimedia
Data Path v2.0 (MDP 2.0) and Display (DISP). The multimedia controller
includes bus fabric control, Smart Memory Interface (SMI) control,
memory access second-level arbiter, and multimedia configuration. It
plays the key role in handling different handshakings between infra
subsystem, video subsystem, image subsystem and G3D subsystem.
For more detail, ask Mediatek for the MT8365 IoT application processor
functional specification.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230207-iommu-support-v6-1-24453c8625b3@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The PMIC regulator node is missing regulator supplies. Now that the
binding supports them, add all the power rail supplies. Most of them
are fed from a system-wide semi-regulated power rail. A couple LDOs
are fed from the PMIC's own buck regulator outputs.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230928085537.3246669-13-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add basic device-tree for the Genio 1200-EVK board. This board
is made by MediaTek and has a MT8395 SoC (MT8195 family),
associated with the MT6359 and MT6360 PMICs, and
the MT7921 connectivity chip.
The IOs available on that board are:
* 1 USB Type-C connector with DP aux mode support
* 2 USB Type-A connector with a USB hub
* 1 micro-USB port for gadget or OTG support
* 1 full size HDMI RX and 1 full size HDMI TX connector
* 1 micro SD slot
* 40 pins header
* SPI interface header
* 1 M.2 slot
* 1 audio jack
* 1 micro-USB port for serial debug
* 2 connectors for DSI displays, 1 of the DSI panel is installed
* 3 connectors for CSI cameras
* 1 connector for a eDP panel
* 1 MMC storage
* 1 Touch Panel (installed DSI display)
* 1 M.2 slot for 5G dongle
This commit adds basic support in order to be able to boot.
Signed-off-by: Ben Lok <ben.lok@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230914055145.16801-2-macpaul.lin@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
1. Add compatible for MT8395.
2. Add bindings for the MediaTek mt8395-evk board, also known
as the "Genio 1200-EVK".
The MT8195 and MT8395 belong to the same SoC family,
with only minor differences in their physical characteristics.
They utilize unique efuse values for differentiation.
The booting process and configurations are managed by boot
loaders, firmware, and TF-A. Consequently, the part numbers
and procurement channels vary.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230914055145.16801-1-macpaul.lin@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use event codes with linux-event-codes.h included for input keys on
midas.
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Link: https://lore.kernel.org/r/20231017101647.62770-1-raymondhackley@protonmail.com
[krzysztof: drop header include, because it is already provided by
dt-bindings/input/input.h]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Input event code 139 stands for KEY_MENU, instead of KEY_OK as node name
key-ok inplies. Fix it with correct event code 0x160.
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Link: https://lore.kernel.org/r/20231017101636.62755-1-raymondhackley@protonmail.com
[krzysztof: use KEY_OK constant instead of raw value]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Parse SFDP table to get size and functions of mt25qu512a. BFPT wrongly
advertises 16bit SR support and made the locking fail. Add a post BFPT
fixup hook to clear the 16bit SR support.
cat /sys/bus/spi/devices/spi-PRP0001:00/spi-nor/jedec_id
20bb20104400
cat /sys/bus/spi/devices/spi-PRP0001:00/spi-nor/manufacturer
st
cat /sys/bus/spi/devices/spi-PRP0001:00/spi-nor/partname
mt25qu512a
xxd -p /sys/bus/spi/devices/spi-PRP0001:00/spi-nor/sfdp
53464450060101ff00060110300000ff84000102800000ffffffffffffff
ffffffffffffffffffffffffffffffffffffe520fbffffffff1f29eb276b
273b27bbffffffffffff27bbffff29eb0c2010d80f520000244a99008b8e
03e1ac0127387a757a75fbbdd55c4a0f82ff81bd3d36ffffffffffffffff
ffffffffffffffffffe7ffff21dcffff
md5sum /sys/bus/spi/devices/spi-PRP0001:00/spi-nor/sfdp
610efba1647e00ac6db18beb11e84c04
/sys/bus/spi/devices/spi-PRP0001:00/spi-nor/sfdp
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20231017074711.12167-2-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
mt25qu512a supports locking/unlocking through the SR BP bits. Enable
locking support. Tested with mtd-utils- flash_lock/flash_unlock on
MT25QU512ABB8E12.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Link: https://lore.kernel.org/r/20231017074711.12167-1-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The new sign/verify code broke the case of pkcs1pad without a
hash algorithm. Fix it by setting issig correctly for this case.
Fixes: 63ba4d6759 ("KEYS: asymmetric: Use new crypto interface without scatterlists")
Cc: stable@vger.kernel.org # v6.5
Reported-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Meteor Lake has demonstrated consistent stability for some time.
All user-space API modifications tide to its core platform
functions are operational.
The necessary firmware components are set up and comprehensive
testing has been condused over a period.
Given the recent faborable CI results, as well, we believe it's
time to eliminate the 'force_probe' prerequisite and activate the
platform by default.
Signed-off-by: Aditya Chauhan <aditya.chauhan@intel.com>
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Chris Wilson <chris.p.wilson@linux.intel.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Lee Shawn C <shawn.c.lee@intel.com>
Tested-by: Lee Shawn C <shawn.c.lee@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231008164824.919262-1-andi.shyti@linux.intel.com
Enable GuC TLB invalidations for MTL. Though more platforms than just
MTL support GuC TLB invalidations, MTL is presently the only platform
that requires it for any purpose, so only enable it there for now to
minimize cross-platform impact.
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231017180806.3054290-8-jonathan.cavitt@intel.com
For the gt_tlb live selftest, when operating on the GSC engine,
increase the timeout from 10 ms to 200 ms because the GSC
engine is a bit slower than the rest.
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231017180806.3054290-7-jonathan.cavitt@intel.com
It is not an error for GuC TLB invalidations to fail when the GT is
wedged or disabled, so do not process a wait failure as one in
guc_send_invalidate_tlb.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
CC: John Harrison <john.c.harrison@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231017180806.3054290-6-jonathan.cavitt@intel.com
In case of GT is suspended, don't allow submission of new TLB invalidation
request and cancel all pending requests. The TLB entries will be
invalidated either during GuC reload or on system resume.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
CC: John Harrison <john.c.harrison@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231017180806.3054290-5-jonathan.cavitt@intel.com
The GuC firmware had defined the interface for Translation Look-Aside
Buffer (TLB) invalidation. We should use this interface when
invalidating the engine and GuC TLBs.
Add additional functionality to intel_gt_invalidate_tlb, invalidating
the GuC TLBs and falling back to GT invalidation when the GuC is
disabled.
The invalidation is done by sending a request directly to the GuC
tlb_lookup that invalidates the table. The invalidation is submitted as
a wait request and is performed in the CT event handler. This means we
cannot perform this TLB invalidation path if the CT is not enabled.
If the request isn't fulfilled in two seconds, this would constitute
an error in the invalidation as that would constitute either a lost
request or a severe GuC overload.
With this new invalidation routine, we can perform GuC-based GGTT
invalidations. GuC-based GGTT invalidation is incompatible with
MMIO invalidation so we should not perform MMIO invalidation when
GuC-based GGTT invalidation is expected.
The additional complexity incurred in this patch will be necessary for
range-based tlb invalidations, which will be platformed in the future.
Signed-off-by: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com>
Signed-off-by: Bruce Chang <yu.bruce.chang@intel.com>
Signed-off-by: Chris Wilson <chris.p.wilson@intel.com>
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Aravind Iddamsetty <aravind.iddamsetty@intel.com>
Signed-off-by: Fei Yang <fei.yang@intel.com>
CC: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231017180806.3054290-4-jonathan.cavitt@intel.com
As of now, there is no mechanism for tracking a given request's
progress through the queue. Instead, add a helper that returns
an estimated maximum time the queue should take to drain if
completely full.
Suggested-by: John Harrison <john.c.harrison@intel.com>
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: John Harrison <john.c.harrison@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231017180806.3054290-3-jonathan.cavitt@intel.com
If we can't find a free fence register to handle a fault in the GMADR
range just return VM_FAULT_NOPAGE without populating the PTE so that
userspace will retry the access and trigger another fault. Eventually
we should find a free fence and the fault will get properly handled.
A further improvement idea might be to reserve a fence (or one per CPU?)
for the express purpose of handling faults without having to retry. But
that would require some additional work.
Looks like this may have gotten broken originally by
commit 39965b3766 ("drm/i915: don't trash the gtt when running out of fences")
as that changed the errno to -EDEADLK which wasn't handle by the gtt
fault code either. But later in commit 2feeb52859 ("drm/i915/gt: Fix
-EDEADLK handling regression") I changed it again to -ENOBUFS as -EDEADLK
was now getting used for the ww mutex dance. So this fix only makes
sense after that last commit.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9479
Fixes: 2feeb52859 ("drm/i915/gt: Fix -EDEADLK handling regression")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012132801.16292-1-ville.syrjala@linux.intel.com
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
(cherry picked from commit 7f403caabe)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
