Register the vchiq_bus_type bus with the vchiq interface.
The bcm2835-camera and bcm2835_audio will be registered to this bus type
going ahead.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Link: https://lore.kernel.org/r/20230923143200.268063-5-umang.jain@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devices that the vchiq interface registers (bcm2835-audio,
bcm2835-camera) are implemented and exposed by the VC04 firmware.
The device tree describes the VC04 itself with the resources required
to communicate with it through a mailbox interface. However, the
vchiq interface registers these devices as platform devices. This
also means the specific drivers for these devices are getting
registered as platform drivers. This is not correct and a blatant
abuse of platform device/driver.
Add a new bus type, vchiq_bus_type and device type (struct vchiq_device)
which will be used to migrate child devices that the vchiq interfaces
creates/registers from the platform device/driver.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Link: https://lore.kernel.org/r/20230923143200.268063-4-umang.jain@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the following patches, vchiq_arm will be migrated to create and use
its own bus and all the vchiq drivers (bcm2835-camera, bcm2835-audio)
will be registered to it. Since the platform driver/device model
internally sets the DMA mask for its registered devices, we would have
to do it ourself when we remove the platform driver/device registration
for vchiq devices.
This patch explicitly sets the DMA mask to bcm2835-audio so as not
to introduce a regression when we move away from platform
device/driver model.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Link: https://lore.kernel.org/r/20230923143200.268063-3-umang.jain@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the following patches, vchiq_arm will be migrated to create and use
its own bus and all the vchiq drivers (bcm2835-camera, bcm2835-audio)
will be registered to it. Since the platform driver/device model
internally sets the DMA mask for its registered devices, we would have
to do it ourself when we remove the platform driver/device registration
for vchiq devices.
This patch explicitly sets the DMA mask to bcm2835-camera so as not
to introduce a regression when we move away from platform
device/driver model.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Link: https://lore.kernel.org/r/20230923143200.268063-2-umang.jain@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the function _rtl92e_if_silent_reset() is called the variable
priv->rst_progress is set to RESET_TYPE_SILENT.
Since priv->up is always true the function is left at "if (priv->up) {"
without resetting. Now the function _rtl92e_if_silent_reset() is like
deactivated because the equation at the very beginning is false:
"if (priv->rst_progress == RESET_TYPE_NORESET) {"
This leads to a state where the driver hangs in the reset state and
cannot go forward.
In 30% of the cases the wlan is disconnected and cannot reconnect. The
rest of the time it continues working but no reset is done at all.
Further requests for reset are ignored. Remove broken function
_rtl92e_if_silent_reset() and remove return value of
_rtl92e_if_check_reset() to avoid compiler warnings.
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/8b1b04b512b5691968a49308fdc052973fbe5032.1696165351.git.philipp.g.hortmann@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of _rtl92e_tx_check_stuck() and _rtl92e_rx_check_stuck()
can only be RESET_TYPE_SILENT or RESET_TYPE_NORESET. This functions are
only used in _rtl92e_if_check_reset(). In _rtl92e_if_check_reset() the
return values are checked for RESET_TYPE_NORMAL which cannot occur.
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/5f29332205dd76896e981fa627925d62a6bf7f63.1696165351.git.philipp.g.hortmann@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As &priv->tx_dev.tx_dev_lock is also acquired by xmit callback which
could be call from timer under softirq context, use spin_lock_bh()
on it to prevent potential deadlock.
hostif_sme_work()
--> hostif_sme_set_pmksa()
--> hostif_mib_set_request()
--> ks_wlan_hw_tx()
--> spin_lock(&priv->tx_dev.tx_dev_lock)
ks_wlan_start_xmit()
--> hostif_data_request()
--> ks_wlan_hw_tx()
--> spin_lock(&priv->tx_dev.tx_dev_lock)
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Link: https://lore.kernel.org/r/20230926161323.41928-1-dg573847474@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just a style change so that the device release callbacks are defined
in the same way for devices in mcb_bus and mcb_device.
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Co-developed-by: Jose Javier Rodriguez Barbarin <JoseJavier.Rodriguez@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <JoseJavier.Rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20230906114901.63174-3-JoseJavier.Rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling mcb_bus_add_devices(), both mcb devices and the mcb
bus will attempt to attach a device to a driver because they share
the same bus_type. This causes an issue when trying to cast the
container of the device to mcb_device struct using to_mcb_device(),
leading to a wrong cast when the mcb_bus is added. A crash occurs
when freing the ida resources as the bus numbering of mcb_bus gets
confused with the is_added flag on the mcb_device struct.
The only reason for this cast was to keep an is_added flag on the
mcb_device struct that does not seem necessary. The function
device_attach() handles already bound devices and the mcb subsystem
does nothing special with this is_added flag so remove it completely.
Fixes: 18d2881980 ("mcb: Correctly initialize the bus's device")
Cc: stable <stable@kernel.org>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Co-developed-by: Jose Javier Rodriguez Barbarin <JoseJavier.Rodriguez@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <JoseJavier.Rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20230906114901.63174-2-JoseJavier.Rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify uart_get_rs485_mode() by using temporary variable for
the GPIO descriptor. With that, use proper type for the flags
of the GPIO descriptor.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231003142346.3072929-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's drop the use of pm_runtime_irq_safe() for 8250_omap. The use of
pm_runtime_irq_safe() is not nice as it takes a permanent usage count on
the parent device.
We can finally drop pm_runtime_irq_safe() safely as the kernel now knows
when the uart port tx is active. This changed with commit 84a9582fd2
("serial: core: Start managing serial controllers to enable runtime PM").
For serial port rx, we already use Linux generic wakeirqs for 8250_omap.
To drop pm_runtime_irq_safe(), we need to add handling for shallow idle
state where the port hardware may already be awake and an IO interrupt
happens. We also need to replace the serial8250_rpm sync calls in the
interrupt handlers with async runtime PM calls.
Note that omap8250_irq() calls omap_8250_dma_handle_irq(), so we don't
need separate runtime PM calls in omap_8250_dma_handle_irq().
While at it, let's also add the missing line break to the end of
omap8250_runtime_resume() to group the calls.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231004062650.64487-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SM8550, the non-altmode orientation is not given anymore within
altmode events, even with USB SVIDs events.
On the other side, the Type-C connector orientation is correctly
reported by a signal from the PMIC.
Take this gpio signal when we detect some Type-C port activity
to notify any Type-C switches tied to the Type-C port connectors.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231002-topic-sm8550-upstream-type-c-orientation-v2-2-125410d3ff95@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SM8450 and SM8550 based platforms, the Type-C plug orientation is given on a
GPIO line for each connector which are set by the PMIC(s).
Document this optional Type-C connector property, and take the
assumption an active level represents an inverted/flipped orientation.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231002-topic-sm8550-upstream-type-c-orientation-v2-1-125410d3ff95@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "c_terminal_type" and "p_terminal_type" configfs entries
in order to allow the user to change the capture and playback terminal
type codes.
These fields affect the type of audio device that Windows detects, so
being able to modify this is useful when it would be advantageous for
a gadget to be detected as something other than a generic
speaker/microphone.
The fields default to microphone for the capture type field and speaker
for the playback type field as was the case before.
Signed-off-by: James Gruber <jimmyjgruber@gmail.com>
Link: https://lore.kernel.org/r/20230914222746.155126-1-jimmyjgruber@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>