The length of the received SKB could be equal to
HTC_RX_FRAME_HEADER_SIZE in case of packets with phy/crc errors,
in which case they are dropped without being processed.
Fix this check so that the error counters are updated correctly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a queue to handle WMI events and schedule a tasklet
to process the events. This fixes the race between the
WMI event ISR and the SWBA tasklet when the arrival of
WMI events in quick succession could overwrite the SWBA
data before the tasklet from a previous iteration could
have been scheduled. Also, drain the WMI queue properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transmission of beacons becomes erratic when TX load
is high, since the latency involved in the generation
of a SWBA interrupt on the target to the actual sending
of a beacon is quite high for USB devices.
Fix this by adjusting the beacon response time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the CAB endpoint to send buffered multicast or
broadcast frames after each SWBA event.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set operating parameters (cwmin, cwmax) for the beacon queue
in AP mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi-interface mode, beacons/probe responses that are
sent out must have their timestamp field updated. Calculate
the TSF adjustment value for each beaconing interface and set it
in the frame properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission is now handled through a slot mechanism.
This allows multiple beaconing interfaces to be be present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Match the beacon header with that of the firmware.
Also, the firmware reports the TSF for an SWBA, so
store it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, update the wiphy information and use the correct
device pointer when registering. This would fix ethtool.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the new FW requires backward incompatible host driver changes,
rename the FW to allow older driver versions to work with the
older FW.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the AR7010 devices supoprted by ath9k_htc are based
on version v1.1, so remove support for v1.0.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, ampdu stream is created on the first qos packet to an
HT sta. The overhead of setting up the BA session may not be
justified if the outgoing packet rate is minimal (e.g., ping). So
we only allow ampdu streams after seeing a critical number of
packets in an arbitrary one-second interval.
Based on work by Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it easier to handle moving stations to VLAN interfaces that are
part of a different bridge.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.
Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.
As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not need to enable all the interrupts in mwl8k_probe_hw.
We need to enable only MWL8K_A2H_INT_OPC_DONE interrupt for sending
commands to the firmware. Keep the other interrupts masked in
mwl8k_probe_hw. Also, in mwl8k_start, where we expect other interrupts,
enable only those interrupts we are interested in.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was done to handle a number of conflicts, the majority of which
were caused by the big "fix spelling issues" patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While decoding a secinfo reply, I store the list of supported sec
flavors on a page accessible through res->flavors. Before reading
each new flavor, I do some math to determine if there is enough
space left on this page, and I break out of my read look if there
isn't. In order to perform this check correctly, I need to use the
address of res->flavors, rather than the address of res.
When this loop was broken early I lied to the caller and told them
that the entire list had been decoded. This could lead to problems
if the caller tries to use any the garbage data claiming to be a
valid sec flavor. I fixed this by using res->flavors->num_flavors
as a counter, incrementing it every time a sec flavor is
successfully decoded.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We were always attempting sec flavor negotiation, even if the user
told us a specific sec flavor to use. If that sec flavor fails,
we should return an error rather than continuing with sec flavor
negotiation.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
nfs4_lookup_root() is already configured to use either RPC_AUTH_UNIX
or a user specified flavor (through -o sec=<whatever>). We should
use this flavor first, and only attempt negotiation if it fails
with -EPERM.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NFS_MAX_SECFLAVORS should already take into account RPC_AUTH_UNIX
and RPC_AUTH_NULL, so we don't need to set aside extra slots
for them.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There can be an infinite loop if gss_create_upcall() is called without
the userspace program running. To prevent this, we return -EACCES if
we notice that pipe_version hasn't changed (indicating that the pipe
has not been opened).
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like
[ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit c191a836a9.
It causes known regressions for programs that expect to be able to use
SO_REUSEADDR to shutdown a socket, then successfully rebind another
socket to the same ID.
Programs such as haproxy and amavisd expect this to work.
This should fix kernel bugzilla 32832.
Signed-off-by: David S. Miller <davem@davemloft.net>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 74888760d4
"dt/net: Eliminate users of of_platform_{,un}register_driver"
broke building mscan driver. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool support to configure RX, TX and other channels. combined field
in struct ethtool_channels to reflect set of channel (RX, TX or other).
Other channel can be link interrupts, SR-IOV coordination etc.
ETHTOOL_GCHANNELS will report max and current number of RX channels,
max and current number of TX channels, max and current number of other channel
or max and current number of combined channel.
Number of channel can be modify upto max number of channel through
ETHTOOL_SCHANNELS command.
Ben Hutchings:
o define 'combined' and 'other' types. Most multiqueue drivers pair up RX and TX
queues so that most channels combine RX and TX work.
o Please could you use a kernel-doc comment to describe the structure.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the dfbmcs320 device which provides the PCM DAI for the bluetooth
module.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the newly introduced dapm_widgets, dpam_routes and controls fields of the
snd_soc_dai_driver struct to setup controls and DAPM.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use SND_SOC_DAPM_EVENT_OFF for determining whether the speaker should be turned
on or off instead of open coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch changes the qi_lb60 setup code to use gpio_request_array instead of
manually calling gpio_request and gpio_direction_output for each gpio.
Doing so makes the code a bit more compact.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the newly introduced dapm_widgets, dpam_routes and fields of the
snd_soc_card struct to setup DAPM.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Those should not be modified (and are not) by the core code, so make them const.
This also makes them consistent with the same members of snd_soc_codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit ce6120cc(ASoC: Decouple DAPM from CODECs) changed the signature of
snd_soc_dapm_widgets_new to take an pointer to a snd_soc_dapm_context instead of
a snd_soc_codec. The call to snd_soc_dapm_widgets_new in jz4740_codec_dev_probe
was not updated to reflect this change, which results in a compiletime warning
and a runtime OOPS.
Since the core code calls snd_soc_dapm_widgets_new after the codec has been
registered it can be dropped here.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
mark_inode_dirty_sync() grabs the same inode lock!
race conditions between holding the lock in pnfs_set_layoutcommit() and in
mark_inode_dirty_sync() can result in a second call to pnfs_layoutcommit_inode(), but
this will be a noop as NFS_INO_LAYOUTCOMMIT won't be set in the second call
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allow audio paths through the Speyside system to be kept active while the
system is suspended (for example, when on a voice call) by marking all the
external widgets and the DAI link to the WM1250-EV1 baseband module as
ignoring suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Demonstrate the connection of a baseband to the system. We add a DAI for
the link to the baseband. This will become visible to the application
layer - audio should be started from the application layer using an
application such as this:
http://opensource.wolfsonmicro.com/~gg/bluetooth-pcm/bluetooth_pcm.c
which starts up audio as for CPU based playback and record up to the point
where data is streamed.
Due to non-availability of baseband simulation hardware we reuse the
configuration for the CPU link with the CODEC acting as clock master,
allowing signals to be observed with a scope. A more standard system
would have separate configuration for the baseband with its own ops
structure and operations. Normally the baseband would be clock master
as the baseband audio will be synchronised to the external telephony
network.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Pin switches enable direct control of the DAPM state from userspace,
enabling simple enabling and disabling of the path. This is especially
useful for outputs such as the speaker which are composed of several
physical devices as it allows them to be controlled as a group.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Speyside makes use of support the WM8915 has for detecting the polarity
of the microphone and ground connections on headsets, using a GPIO to
control the polarity of the ground connection and switching between the
two microphone bias supplies available on the device in order to do so.
As a result of this the detection support is more involved than for most
other CODECs, using a callback to configure the current polarity of the
jack and translate this into the board-specific connections required for
the current scenario.
On Android some additional work is required to hook this up to the
application layer as the Android HeadsetObserver monitors a custom
drivers/switch API rather than the standard Linux APIs. This can be
done by either updating HeadsetObserver or modifying the ALSA core to
report via drivers/switch as well.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Speyside includes a WM9081 configured as an external speaker driver taking
an analogue input from HPOUT2 on the WM8915 on the system. Add support for
this to the driver, using a prefix of "Sub" for the WM9081 controls to
ensure we avoid collisions with controls on the WM8915.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Dynamically enable and disable the FLL on the WM8915, configuring the
system clock to 256fs for 48kHz when the device is active but reverting
to using the input 32.768kHz clock directly at other times to support
features such as jack detection with minimal power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Provide widgets for the basic widgets connected directly to the WM8915
on Speyside - the headphones, speaker, digital and analogue microphones.
For the outputs this is just documentation, for the inputs this ensures
that the relevant microphone biases are enabled when they are in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This is minimal code required to get audio out of the Speyside audio
subsystem on the Wolfson Cragganmore 6410 reference platform. It sets
up the link between the CPU and AIF1 of the WM8915 on the system,
enabling audio playback via the headphone and speaker outputs of the
device (which require no further configuration except runtime). It
allows verification of basic functionality of the system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This helps with things like setting up the initial state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
