When pgdat is reserved in init_remap_allocator(), PAGE_SIZE aligned
size will be used. Match the size alignment in initialization to
avoid allocation failure down the road.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-3-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
node_remap_{start|end}_vaddr[] describe [start, end) ranges; however,
alloc_remap() incorrectly failed when the current allocation + size
equaled the end but it should fail only when it goes over. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1301955840-7246-2-git-send-email-tj@kernel.org
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
initialize ret to invalid value so that when we reach the config error path in
soc_pcm_open, it will return the correct error code. without this patch, though
config error path is executed, soc_pcm_open will return 0 in
snd_pcm_open_substream and then cause double release of substream.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Suppose we have:
cpu_dai
channels_min = 1
channels_max = 1
codec_dai
channels_min = 2
channels_max = 2
This is a mismatch that should not happen, however according to the current
code, the result of runtime->hw will be:
channels_min = 2
channels_max = 1
We better spot it early. This patch checks this mismatch.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For isochronous packets the actual_length is the sum of the actual
length of each of the packets, however between the packets might be
padding, so it is not sufficient to just send the first actual_length
bytes of the buffer. To fix this and simultanesouly optimize the
bandwidth the content of the isochronous packets are send without the
padding, the padding is restored on the receiving end.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number_of_packets was not transmitted for RET_SUBMIT packets. The
linux client used the stored number_of_packet from the submitted
request. The windows userland client does not do this however and needs
to know the number_of_packets to determine the size of the transmission.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When doing a usb port reset do a queued reset instead to prevent a
deadlock: the reset will cause the driver to unbind, causing the
usb_driver_lock_for_reset to stall.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When shuting down the tcp_rx and tcp_tx threads first check if they are
not closed already (maybe because an error caused them to return).
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After Quick Migration, the network is not immediately operational in the
current context when receiving RNDIS_STATUS_MEDIA_CONNECT event. So, I added
another netif_notify_peers() into a scheduled work, otherwise GARP packet will
not be sent after quick migration, and cause network disconnection.
Thanks to Mike Surcouf <mike@surcouf.co.uk> for reporting the bug and
testing the patch.
Reported-by: Mike Surcouf <mike@surcouf.co.uk>
Tested-by: Mike Surcouf <mike@surcouf.co.uk>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Abhishek Kane <v-abkane@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case of an error in h3600ts_connect(), deconstruct in correct order
and with the right calls.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use ethtool infrastructure for blinking, which is now does
locking at higher level.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to use new ethtool set_phys_id.
Not completely sure that this is correct for all cases of device
up/down and doing operation. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udev fully replaces this special file system that only contains CAPI
NCCI TTY device nodes. User space (pppdcapiplugin) works without
noticing the difference.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes error from sparse:
CHECK drivers/net/xen-netback/xenbus.c
drivers/net/xen-netback/xenbus.c:29:40: error: dubious one-bit signed bitfield
int have_hotplug_status_watch:1;
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eq_next_idx is not getting reset to zero during suspend.
This causes resume to fail. Added the fix.
Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renamed msix_vec_idx to eq_idx in be_eq_obj struct.
Renamed msix_vec_next_idx to eq_next_idx in be_adapter structure.
These members are used in INTX mode also.
Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new ethtool set physical id model. Remove no longer used
timer, and fix docbook comment.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also cleanup error codes to no lie about things that driver doesn't
support. If device is down report -EAGAIN (same as Broadcom), and
if port doesn't blink then error as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this case, need to add element to device private to hold
original led state.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement new ethtool set_phys_id on Chelsio cxgb3 board.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement control of LED via set_phys_id.
Note: since PHY is powered off if device is down, this board
only allows blinking if device is up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set_phys_id led control on SysKonnect board.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ethtool set_phys_id to control LED. Fixes issues with RTNL being
held for extended periods.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
otherwise we loop forever if a PPPoE socket was set
to PPPOX_ZOMBIE state by a PADT message when the
ethernet device is going down afterwards.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6085 is identical to the mv88e6095, except that all ports are
10/100 Mb/s, so use the existing setup code except for the cpu/dsa speed
selection in _setup_port().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rpc_authflavor_t is cast from an unsigned int, but the
initial code tried to use it as a signed int. I fix
this by passing an rpc_authflavor_t pointer around, and
returning signed integers from functions.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Restore the initialization of mmu_cr4_features during boot, which was
removed without comment in checkin e5f15b45dd
x86: Cleanup highmap after brk is concluded
thereby breaking resume from hibernate. This restores previous
functionality in approximately the same place, and corrects the
reading of %cr4 on pre-CPUID hardware (%cr4 exists if and only if
CPUID is supported.)
However, part of the problem is that the hibernate suspend/resume
sequence should manage the save/restore of %cr4 explicitly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <201104020154.57136.rjw@sisk.pl>
properly record sk_rxhash in ipv6 sockets (v2)
Noticed while working on another project that flows to sockets which I had open
on a test systems weren't getting steered properly when I had RFS enabled.
Looking more closely I found that:
1) The affected sockets were all ipv6
2) They weren't getting steered because sk->sk_rxhash was never set from the
incomming skbs on that socket.
This was occuring because there are several points in the IPv4 tcp and udp code
which save the rxhash value when a new connection is established. Those calls
to sock_rps_save_rxhash were never added to the corresponding ipv6 code paths.
This patch adds those calls. Tested by myself to properly enable RFS
functionalty on ipv6.
Change notes:
v2:
Filtered UDP to only arm RFS on bound sockets (Eric Dumazet)
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bumped up version number to 5.0.16
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In dev->open LRO was enabled by default, enable it depending
upon netdev->features , kernel may have disabled it.
o Configure LRO when interface is up.
Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <Anirban.Chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use flash layout table to get flash fw starting address and its size.
If that fails, use legacy method.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleaned up unused codes for interrupt coalescence settings
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Made changes to VLAN code comply with new VLAN infrastructure in kernel
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimized code resulted in achieving lower CPU utilization on transmit path
and higher throughput for small packet sizes (64 bytes).
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Changed adapter structure to move away from embedding hardware and
receive context structs and use pointers to those objects
2. Packed all the structs that interface with FW
3. Removed unused code and structs
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak in error path of pci info.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this fix, PCI info was available only when multiple NIC functions
are present on the same port.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter could remain uninitialized if probe fails for some reason.
A null pointer access could cause a crash if be_shutdown
is called after that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
