Warning: comparison between ‘enum drbd_ret_code’ and ‘enum drbd_state_rv’
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The FAULT_ACTIVE macro just wraps the drbd_insert_fault macro for no
apparent reason.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This macro doesn't save much code, but makes things a lot harder to read.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
commit e2041475e6ddb081734d161f6421977323f5a9b9
drbd: Starting with protocol 96 we can allow app-IO while receiving the bitmap
Contained a bad chunk that tried to optimize away drbd barriers during
bitmap exchange, but accidentally dropped them for normal mode as well.
Impact: depending on activity log size and access pattern, activity log
extents may not be recycled in time, causeing IO to block indefinetely.
Fix: skip drbd barriers only if there is no connection to send them on,
or the request being completed has not been on the network at all.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
As the network connection can be lost at any time, a --force option
for disconnect is just a matter of completeness.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In case we ever should add an other packet type,
we must not reuse 27, as that currently used for
"empty" return code only replies.
Document it as such.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Make sure we start with clean buffers to not accidentally send garbage
back to userspace. Note: has not been observed; but just in case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There still exists a (theoretical) race on module unload, where
/proc/drbd may still exist, but the netlink callback has been
unregistered already, allowing drbdsetup to shout without listeners,
and get no reply.
Reorder remove_proc_entry and unregister of netlink callback.
drbdsetup first checks for existence of the proc entry,
and if that is missing, won't even try to contact the module.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If someone holds /proc/drbd open, previously rmmod would
"succeed" in starting the unload, but then block on remove_proc_entry,
leading to a situation where the lsmod does not show drbd anymore,
but /proc/drbd being still there (but no longer accessible).
I'd rather have rmmod fail up front in this case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Given low-enough network bandwidth combined with a IO
pattern that hammers onto a single RS-extent, side-stepping
might be necessary for much longer times.
Changed the code to print a single informal message after
20 seconds, but it keeps on stepping aside forever.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This patch is acutally a necessary addendum to the patch
"fix for spurious full sync (becoming sync target looked like invalidate)"
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* C_STARTING_SYNC_S, C_STARTING_SYNC_T In these states the bitmap gets
written to disk. Locking out of app-IO is done by using the
drbd_queue_bitmap_io() and drbd_bitmap_io() functions these days.
It is no longer necessary to lock out app-IO based on the connection
state.
App-IO that may come in after the BITMAP_IO flag got cleared before the
state transition to C_SYNC_(SOURCE|TARGET) does not get mirrored, sets
a bit in the local bitmap, that is already set, therefore changes nothing.
* C_WF_BITMAP_S In this state we send updates (P_OUT_OF_SYNC packets).
With that we make sure they have the same number of bits when going
into the C_SYNC_(SOURCE|TARGET) connection state.
* C_UNCONNECTED: The receiver starts, no need to lock out IO.
* C_DISCONNECTING: in drbd_disconnect() we had a wait_event()
to wait until ap_bio_cnt reaches 0. Removed that.
* C_TIMEOUT, C_BROKEN_PIPE, C_NETWORK_FAILURE
C_PROTOCOL_ERROR, C_TEAR_DOWN: Same as C_DISCONNECTING
* C_WF_REPORT_PARAMS: IO still possible since that is still
like C_WF_CONNECTION.
And we do not need to send barriers in C_WF_BITMAP_S connection state.
Allow concurrent accesses to the bitmap when receiving the bitmap.
Everything gets ORed anyways.
A drbd_free_tl_hash() is in after_state_chg_work(). At that point
all the work items of the last connections must have been processed.
Introduced a call to drbd_free_tl_hash() into drbd_free_mdev()
for paranoia reasons.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The relevant change is that the state change to C_FW_BITMAP_S should
implicitly change pdsk to C_CONSISTENT. (Think of it as C_OUTDATED, only
without the guarantee that the peer has the outdated written to its
meta data)
At that opportunity I restructured the switch statement so that it
gets evaluated every time. (Has declarative character)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
May only test for ap_bio_cnt == 0 under req_lock. It can increase
only under req_lock.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The condition must be checked after perpare_to_wait(). The old
implementaion could loose wakeup events. Never observed in real
life.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since inc_ap_bio() might sleep already
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Before:
drbd_rs_begin_io() locked app-IO out of an RS extent, and
waited then until all previous app-IO in that area finished.
(But not only until the disk-IO was finished but until the
barrier/epoch ack came in for that == round trip time latency ++)
After:
As soon as a new app-IO waits wants to start new IO on that
RS extent, drbd_rs_begin_io() steps aside (clearing the
BME_NO_WRITES flag again). It retries after 100ms.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We only issue resync requests if there is no significant application IO
going on. = Application IO has higher priority than resnyc IO.
If application IO can not be started because the resync process locked
an resync_lru entry, start the IO operations necessary to release the
lock ASAP.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This one should be replaced with moving this cleanup to the
'right' position.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In this connection mode, the ahead node no longer replicates
application IO. The behind's disk becomes out dated.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.
This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
variable; improved some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_init_clock always returns 0 and does
not propogate the error (in case of failure)
back to the caller, causing _init_clocks to
fail silently.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Autoidle is a single bit, TIOCP_CFG[0], setting on OMAP1/2/3/4 platforms.
In _set_module_autoidle() I am seeing 0x3 value where the mask is computed.
This should be 0x1.
v2:
(1) Modified the subject.
(2) Modified the description with further specific information.
Baseline:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
Tested Info:
Boot tested on OMAP 1/2/3/4.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit
drbd: further converge progress display of resync and online-verify
accidentally an u64/u64 div was introduced, causing an unresolvable
symbol __udivdi3 to be reference. Actually for that division, 32bit are
still suficient for now, so we can revert to unsigned long instead.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To ease tracking of bios in some hash tables, we want it to
not cross certain boundaries (128k, used to be 32k).
We limit the maximum bio size using queue parameters.
Historically some defines and variables we use there have been named
max_segment_size, which was misguided. Rename them to max_bio_size,
and use [blk_]queue_max_hw_sectors where appropriate.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We used to be limited to 32k requests,
but have increased that limit to 128k now.
This part of the code can only deal with 32k,
it would scramble arbitrary pages for larger requests.
As it is used for debugging only anyways,
it is ok to simply truncate the dumped data here.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With data-integrity digest enabled, double-check on the sending side
for modifications by upper layers of buffers under write back,
so we can tell it appart from corruption on the "wire".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Show progressbar and ETA always, with proc_details >= 1 also show the
current sector position for both resync and online-verify on both nodes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
