omap4 interrupt disable bits is different. On rx kfifo full, the mbox rx
interrupts wasn't getting disabled, and this is causing the rcm stress tests
to hang.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Armando Uribe <x0095078@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
First, this was racy anyway: d_release isn't called until well after the
dentry is unhashed. Second, this runs afoul of the recent dcache change
that clears d_parent prior to calling d_release (949854d0), causing a NULL
pointer dereference.
Signed-off-by: Sage Weil <sage@newdream.net>
This reverts commit 97d79b403e.
This fails to account for d_parent changes due to rename or disconnected
dentries due to submounts or NFS reexports.
Signed-off-by: Sage Weil <sage@newdream.net>
The temperature reported by 'cat /sys/class/net/wlan?/device/temperature'
is incorrect for devices with BT capability. Report the value from the
correct statistics structure. Tested with 130, 100, 6205 and 5300.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We only did this for PV guests that are xen_initial_domain() but
there is not reason not to do this for other cases. The other
case is only exercised when you pass in a PCI device to a PV guest
_and_ the device in question.
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Mark the IRQF_NO_SUSPEND interrupts IRQF_FORCE_RESUME and remove the extra
walk through the interrupt descriptors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The patches missed an indirect use of IRQF_NO_SUSPEND pulled in via
IRQF_TIMER. The following patch fixes the issue.
With this fixlet PV guest migration works just fine. I also booted the
entire series as a dom0 kernel and it appeared fine.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
drivers/xen/events.c: In function 'ack_pirq':
drivers/xen/events.c:568: error: implicit declaration of function 'irq_move_irq'
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Convert Xen to the new irq_chip functions. Brings us closer to enable
CONFIG_GENERIC_HARDIRQS_NO_DEPRECATED
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
irq_chip.end got obsolete with the removal of __do_IRQ()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
c514d00c8057 "xen: events: add xen_allocate_irq_{dynamic, gsi} and
xen_free_irq" correctly avoids reallocating legacy IRQs (which are
managed by the arch core) but erroneously did not prevent them being
freed.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There are three cases which we need to care about, PV guest, PV domain
0 and HVM guest.
The PV guest case is simple since it has no access to ACPI or real
APICs and therefore has no GSIs therefore we simply dynamically
allocate all IRQs. The potentially interesting case here is PIRQ type
event channels associated with passed through PCI devices. However
even in this case the guest has no direct interaction with the
physical GSI since that happens in the PCI backend.
The PV domain 0 and HVM guest cases are actually the same. In domain 0
case the kernel sees the host ACPI and GSIs (although it only sees the
APIC indirectly via the hypervisor) and in the HVM guest case it sees
the virtualised ACPI and emulated APICs. In these cases we start
allocating dynamic IRQs at nr_irqs_gsi so that they cannot clash with
any GSI.
Currently xen_allocate_irq_dynamic starts at nr_irqs and works
backwards looking for a free IRQ in order to (try and) avoid clashing
with GSIs used in domain 0 and in HVM guests. This change avoids that
although we retain the behaviour of allowing dynamic IRQs to encroach
on the GSI range if no suitable IRQs are available since a future IRQ
clash is deemed preferable to failure right now.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
This is neater than open-coded calls to irq_alloc_desc_at and
irq_free_desc.
No intended behavioural change.
Note that we previously were not checking the return value of
irq_alloc_desc_at which would be failing for GSI<NR_IRQS_LEGACY
because the core architecture code has already allocated those for
us. Hence the additional check against NR_IRQS_LEGACY in
xen_allocate_irq_gsi.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
The only caller is xen_allocate_pirq_msi which is also under this
ifdef so this fixes:
drivers/xen/events.c:377: warning: 'find_unbound_pirq' defined but not used
when CONFIG_PCI_MSI=n
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
This happens to not be an issue currently because we take pains to try
to ensure that the GSI-IRQ mapping is 1-1 in a PV guest and that
regular event channels do not clash. However a subsequent patch is
going to break this 1-1 mapping.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
The 34xx and 3590 tape driver uses the system work queue to defer work
from the interrupt function to process context, e.g. a medium sense
after an unsolicited interrupt. The tape commands started by the work
handler need to be asynchronous, otherwise a deadlock on the system
work queue can occur.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The "ct" variable should be an unsigned int. Both struct kbdiacrs
->kb_cnt and struct kbd_data ->accent_table_size are unsigned ints.
Making it signed causes a problem in KBDIACRUC because the user could
set the signed bit and cause a buffer overflow.
Cc: <stable@kernel.org>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The module parameter 'devs' and 'sizes' are marked as __initdata. The
memory for the parameters are freed after module_init completed. This
can lead to kernel crashes in param_free_charp. Remove the __initdata
attribute to fix the problem.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With this patch, we diligently set regions that will be used by the
balloon driver to be INVALID_P2M_ENTRY and under the ownership
of the balloon driver. We are OK using the __set_phys_to_machine
as we do not expect to be allocating any P2M middle or entries pages.
The set_phys_to_machine has the side-effect of potentially allocating
new pages and we do not want that at this stage.
We can do this because xen_build_mfn_list_list will have already
allocated all such pages up to xen_max_p2m_pfn.
We also move the check for auto translated physmap down the
stack so it is present in __set_phys_to_machine.
[v2: Rebased with mmu->p2m code split]
Reviewed-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
iwlagn: Support new 1000 microcode.
New iwlwifi-1000 microcode requires driver support for API version 5.
(There is no version 4)
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If we enable trace events to trace block actions, We use
blk_fill_rwbs_rq to analyze the corresponding actions
in request's cmd_flags, but we only choose the minor 2 bits
from it, so most of other flags(e.g, REQ_SYNC) are missing.
For example, with a sync write we get:
write_test-2409 [001] 160.013869: block_rq_insert: 3,64 W 0 () 258135 + =
8 [write_test]
Since now we have integrated the flags of both bio and request,
it is safe to pass rq->cmd_flags directly to blk_fill_rwbs and
blk_fill_rwbs_rq isn't needed any more.
With this patch, after a sync write we get:
write_test-2417 [000] 226.603878: block_rq_insert: 3,64 WS 0 () 258135 +=
8 [write_test]
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Set the gf_protection bit when calling ACX_HT_BSS_OPERATION according
to the GF bit passed by mac80211 in ht_operation_mode.
[Added a proper commit message -- Luca]
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commands are sometimes sent to FW on scan completion. Make sure the chip
is awake to receive them. Sending commands while the chip is in ELP
can cause SDIO read errors and/or crash the FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The errata init verbs for CS42xx codecs contain the verbs to set
the power-state of SPDIF nodes to D3, which seem to break the SPDIF
output on some MacBooks. Since this is executed during the power-up
initialization, we shouldn't turn them down there.
Reported-by: Arun Raghavan <arun.raghavan@collabora.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tests have shown that the requested number of memory blocks is
sub-optimal. Slightly modify the requested number of memory blocks for
TX.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
TX might be handled in the threaded IRQ handler, in which case, TX work
might be scheduled just to discover it has nothing to do.
Save a few context switches by cancelling redundant TX work in case TX
is about to be handled in the threaded IRQ handler. Also, avoid
scheduling TX work from wl1271_op_tx if not needed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interrupt of the wl12xx is a level interrupt in nature, since the
interrupt line is not auto-reset. However, since resetting the interrupt
requires bus transactions, this cannot be done from an interrupt
context. Thus, requesting a level interrupt would require to disable the
irq and re-enable it after the HW is acknowledged. Since we now request
a threaded irq, this can also be done by specifying the IRQF_ONESHOT
flag.
Triggering on an edge can be problematic in some platforms, if the
sampling frequency is not sufficient for detecting very frequent
interrupts. In case an interrupt is missed, the driver will hang as the
interrupt line will stay high until it is acknowledged by the driver,
which will never happen.
Fix this by requesting a level triggered interrupt, with the
IRQF_ONESHOT flag.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
To achieve maximal throughput, it is very important to react to
interrupts as soon as possible. Currently the interrupt handler wakes up
a worker for handling interrupts in process context. A cleaner and more
efficient design would be to request a threaded interrupt handler. This
handler's priority is very high, and can do blocking operations such as
SDIO/SPI transactions.
Some work can be deferred, mostly calls to mac80211 APIs
(ieee80211_rx_ni and ieee80211_tx_status). By deferring such work to a
different worker, we can keep the irq handler thread more I/O
responsive. In addition, on multi-core systems the two threads can be
scheduled on different cores, which will improve overall performance.
The use of WL1271_FLAG_IRQ_PENDING & WL1271_FLAG_IRQ_RUNNING was
changed. For simplicity, always query the FW for more pending
interrupts. Since there are relatively long bursts of interrupts, the
extra FW status read overhead is negligible. In addition, this enables
registering the IRQ handler with the ONESHOT option.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The SDIO bus is claimed and released for each SDIO transaction. In
addition to the few CPU cycles it takes to claim and release the bus, it
may also cause undesired side effects such as the MMC host stopping its
internal clocks.
Since only the wl12xx_sdio driver drives this SDIO card, it is safe to
claim the SDIO host once (on power on), and release it only when turning
the power off.
This patch was inspired by Juuso Oikarinen's (juuso.oikarinen@nokia.com)
patch "wl12xx: Change claiming of the (SDIO) bus".
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On newer hardware revisions, there is no need to write the host's
counter at the end of a RX transaction. The same applies to writing the
number of packets at the end of a TX transaction.
It is generally a good idea to avoid unnecessary SDIO/SPI transfers.
Throughput and CPU usage are improved when avoiding these.
Send the host's RX counter and the TX packet count only if needed, based
on the hardware revision.
[Changed WL12XX_QUIRK_END_OF_TRANSACTION to use BIT(0) -- Luca]
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW has a limited amount of memory for holding frames. In case it
runs out of memory reserved for RX frames, it'll have no other choice
but to drop packets received from the AP. Thus, it is important to
handle RX data interrupts as soon as possible, before handling anything
else.
In addition, since there are enough TX descriptors to go around, it is
better to first send TX frames, and only then handle TX completions.
Fix this by changing the order of function calls in wl1271_irq_work.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Frames in the tx_frames array include extra private headers, which must
be removed before passing the skbs to ieee80211_tx_status.
Fix this by removing any private headers in wl1271_tx_reset, similar to
how this is done in wl1271_tx_complete_packet.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Runtime PM might not always be enabled. Even if it is enabled in the
running kernel, it can still be temporarily disabled, for instance
during suspend. Runtime PM is opportunistic in nature, and should not be
relied on for toggling power.
In case the interface is removed and re-added while runtime PM is
disabled, the FW will fail to boot, as it is mandatory to toggle power
between boots. For instance, this can happen during suspend in case one
of the devices fails to suspend before the MMC host suspends, but after
mac80211 was suspended. The interface will be removed and reactivated
without toggling the power.
Fix this by calling mmc_power_save_host/mmc_power_restore_host in
wl1271_sdio_power_on/off functions. It will toggle the power to the chip
even if runtime PM is disabled. The runtime PM functions should still be
called to make sure runtime PM does not opportunistically power the chip
off (e.g. after resuming from system suspend).
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In the linux-firmware git tree, the firmwares and the NVS are inside
the ti-connectivity directory. Fix the filenames that the driver
looks for accordingly.
[Fixed commit message and merged with the latest changes. -- Luca]
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since multiple codec drivers already use the input-jack stuff, let's
make common helper functions to reduce the duplicated codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Updating the copyrights for 2011 as well as make the ixgbe_copyright string
a constant.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 devices grabs semaphores differently than 82599 and 82598
devices do. They do however also grab them in allot of the same
functions. So I'm adding a new MAC operation function pointer to
allow us to use the correct function based on our MAC type. I'm also
changing all the semaphore calls to use this new function pointer.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up commented out include file and use #define instead of hard coded
value for number of RAR entries.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I2C interface was not being correctly locked down per port. As such
this can lead to race conditions that can cause issues. This patch cleans
up the handling to make certain we are not experiencing racy I2C access.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were reading the address after it had been initialized and this results
in the permanent address on the system being changed. This change corrects
that by storing the address before we re-initialize it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains a number of whitespace and formatting cleanups.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch specifically checks for 100 Full link speed instead of
assuming we are linked at 100 if not linked at 10G and 1G.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make functions used strictly in bool context return bool. Also,
fixup used types and comments, and make a local function static,
while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Borislav Petkov <bp@amd64.org>
LKML-Reference: <20110303115932.GA8603@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added the missing HDMI codec IDs for new Nvidia stuff.
Note that ID 0x17 isn't assigned to anything so far, as suggested by
Stephen.
[Modified to get rid of 0x17 by tiwai]
Signed-off-by: Richard Samson <samson.richard@gmail.com>
Acked-by: Acked-By: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add extra parentheses around a couple of definitions introduced
by "x86: Cleanup vector usage" and used in assembly macro
arguments, and remove spaces. Without that old (2.16.1) gas
would see more macro arguments than were actually specified.
Reported-and-tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <4D6F81B10200007800034B0B@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
