* Increase timeouts on ath5k_hw_stop_tx_dma and also wait for
tx queue to stop before checking for pending frames
* Add a new debug level to debug dma start/stop
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since we stop rx/tx dma and pcu durring reset there is no need to
call ath5k_hw_stop_rx/tx_dma before, also there is no need to call
them durring stop_locked since we can use ath5k_hw_dma_stop for
both.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Stop PCU receive logic (DRU) durring reset
We need to be sure pcu is not active when trying to stop rx dma
right now this is done on ath5k_reset (base.c) but later we are
going to clean it up.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add a new function to stop rx/tx dma and use in when reset starts
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* No functional changes
* Clean up reset:
Introduce init functions for each unit and call them instead
of having everything inside ath5k_hw_reset (it's just c/p for
now so nothing changes except calling order -I tested it with
various cards and it's ok-)
* Further cleanups:
ofdm_timings belongs to phy.c
rate_duration belongs to pcu.c
clock functions are general and belong to reset.c (more to follow)
* Reorder functions for better organization:
We start with helpers and other functions follow in categories,
init functions are last
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.
This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Th commit titled "mac80211: clean up rx handling wrt. found_sta"
removed found_sta variable which caused a MIC failure event
to be reported twice for a single failure to supplicant resulted
in STA disconnect.
This should fix WPA specific countermeasures WiFi test case (5.2.17)
issues with mac80211 based drivers which report MIC failure events in
rx status.
Cc: Stable <stable@kernel.org> (2.6.37)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (as1437) fixes a bug in the usb-serial autosuspend
handling. Since the usb-serial core now has autosuspend support, it
must set the .supports_autosuspend member in every serial driver it
registers. Otherwise the usb_autopm_get_interface() call won't work.
This fixes Bugzilla #23012.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@kernel.org
Reported-by: Kevin Smith <thirdwiggin@gmail.com>
Reported-and-tested-by: Simon Gerber <gesimu@gmail.com>
Reported-and-tested-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tested on MacBookAir3,1. Without this, we get EPROTO errors when
fetching device config descriptors.
Signed-off-by: Brian Tarricone <brian@tarricone.org>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Tested-by: Edgar Hucek <gimli@dark-green.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the PID for the Vardaan Enterprises VEUSB422R3 USB to RS422/485
converter. It uses the same chip as the FTDI_8U232AM_PID 0x6001.
This should also work with the stable branches for:
2.6.31, 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36
Signed-off-by: Jacques Viviers <jacques.viviers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Default llseek operation behavior was changed by the patch named
"vfs: make no_llseek the default" after the yurex driver had been merged,
so the llseek to yurex is now ignored.
This patch add llseek fop with default_llseek to yurex driver
to catch up to the change.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another variant of the RT Systems programming cable for ham radios.
Signed-off-by: Michael Stuermer <ms@mallorn.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an curious issue due to insufficient
rx frame filtering.
Saqeb Akhter reported frequent disconnects while streaming
videos over samba: <http://marc.info/?m=128600031109136>
> [ 1166.512087] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 1526.059997] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 2125.324356] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [...]
The reason is that the device generates frames with slightly
bogus SA/TA addresses.
e.g.:
[ 2314.402316] Ignore 9f:1f:31:f8:64:ff
[ 2314.402321] Ignore 9f:1f:31:f8:64:ff
[ 2352.453804] Ignore 0d:1f:31:f8:64:ff
[ 2352.453808] Ignore 0d:1f:31:f8:64:ff
^^ the group-address flag is set!
(the correct SA/TA would be: 00:1f:31:f8:64:ff)
Since the AP does not know from where the frames come, it
generates a DEAUTH response for the (invalid) mcast address.
This mcast deauth frame then passes through all filters and
tricks the stack into thinking that the AP brutally kicked
us!
This patch fixes the problem by simply ignoring
non-broadcast, group-addressed deauth/disassoc frames.
Cc: Jouni Malinen <j@w1.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Saqeb Akhter <saqeb.akhter@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When comparing filehandles in the helper nfs_same_file(), we should not be
using 'strncmp()': filehandles are not null terminated strings.
Instead, we should just use the existing helper nfs_compare_fh().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file_ops struct for the "trace" special file defined llseek as seq_lseek().
However, if the file was opened for writing only, seq_open() was not called,
and the seek would dereference a null pointer, file->private_data.
This patch introduces a new wrapper for seq_lseek() which checks if the file
descriptor is opened for reading first. If not, it does nothing.
Cc: <stable@kernel.org>
Signed-off-by: Slava Pestov <slavapestov@google.com>
LKML-Reference: <1290640396-24179-1-git-send-email-slavapestov@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This primarily fixes perf-report, which didn't report the correct type
of event if perf-record was called to record one event different from
'cycles':
$ perf record -e instructions true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.007 MB perf.data (~295 samples) ]
$ perf report | head -n1
# Events: 7 cycles
LPU-Reference: <m3mxor6nex.fsf@gmail.com>
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
On ARM, module symbol start address is ahead of kernel symbol start address, so
we can't suppose that the start address of kernel map always is zero, otherwise
may cause incorrect .start and .end of kernel map (caused by fixup) when there
are modules loaded, then map_groups__find may return incorrect map for symbol
query.
This patch always figures out the start address of kernel map from
/proc/kallsyms if the file is available, so fix the issues on ARM for module
loaded case.
This patch fixes the following issues on ARM when modules are loaded:
- vmlinux symbol can't be found by kallsyms maps doing 'perf test'
- module symbols are parsed mistakenlly when doing 'perf top'/'perf report'
Cc: Ian Munsie <imunsie@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <20101125192725.62d31b42@tom-lei>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
On ARM, module addresss space is ahead of kernel space, so the module
symbols are handled before kernel symbol in dso__split_kallsyms, then
was causing one map to be created for each kernel symbol.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <20101124144540.GB15875@ghostprotocols.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
passing argument 2 of 'dma_map_single' discards qualifiers from pointer target type
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
to be a few more concistant with the other boards
as ek is for evaluation kit and dk for development kit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
We can only merge the fields into a bitfield if the locking
rules for them are the same. In this case gl_spin covers all
of the fields (write side) but a couple of them are used
with GLF_LOCK as the read side lock, which should be ok
since we know that the field in question won't be changing
at the time.
The gl_req setting has to be done earlier (in glock.c) in order
to place it under gl_spin. The gl_reply setting also has to be
brought under gl_spin in order to comply with the new rules.
This saves 4*sizeof(unsigned int) per glock.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Bob Peterson <rpeterso@redhat.com>
When you truncate the rindex file, you need to avoid calling gfs2_rindex_hold,
since you already hold it. However, if you haven't already read in the
resource groups, you need to do that.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
New DAPM widgets, and paths to enable both channels at the
same time (for stereo output).
With this path the switch time difference can be avoided
between left and right channels.
The original DAPM paths can be still used, if only one of
TPA's output has been connected to a speaker, but for most of
the cases, switching to the stereo path is better.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reduce the amount of duplicated code by using single
event handler for PGA_E to enable the needed channel.
Use the w->shift to pass the channel information to
the handler function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Do not enable the amplifier right after the power has been
restored to the amplifier.
The DAPM_SUPPLY widget turns on the amp early in the DAPM
power walk, and the unmuting of channel happens quite late.
Keeping the amp in SW reset state ensures better muting.
In this way the pop noise coming from other components (codec)
can be filtered out.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use simpler way to avoid setting the same power state
for the amplifier.
Simplifies the check introduced by patch:
ASoC: tpa6130a2: Fix unbalanced regulator disables
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Verify that the total length of the iovec returned in FUSE_IOCTL_RETRY
doesn't overflow iov_length().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: <stable@kernel.org> [2.6.31+]
If a 32bit CUSE server is run on 64bit this results in EIO being
returned to the caller.
The reason is that FUSE_IOCTL_RETRY reply was defined to use 'struct
iovec', which is different on 32bit and 64bit archs.
Work around this by looking at the size of the reply to determine
which struct was used. This is only needed if CONFIG_COMPAT is
defined.
A more permanent fix for the interface will be to use the same struct
on both 32bit and 64bit.
Reported-by: "ccmail111" <ccmail111@yahoo.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: <stable@kernel.org> [2.6.31+]
During playback start the codec has been already powered at
BIAS_ON event time, so there's no need to enable the codec again.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
No need to enable the codec at this time.
The codec will be enabled later by other events
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When GFS2 grew the filesystem, it was never rereading the rindex file during
the grow. This is necessary for large grows when the filesystem is almost full,
and GFS2 needs to use some of the space allocated earlier in the grow to
complete it. Now, if GFS2 fails to reserve the necessary space and the rindex
file is not uptodate, it rereads it. Also, the only difference between
gfs2_ri_update() and gfs2_ri_update_special() was that gfs2_ri_update_special()
didn't clear out the existing resource groups, since you knew that it was only
called when there were no resource groups. Attempting to clear out the
resource groups when there are none takes almost no time, and rarely happens,
so I simply removed gfs2_ri_update_special().
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
There are a number of duplicated #defines in glock.h
plus one which is unused. This removes the extra
definitions.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Fix kernel-doc warning for set_consumer_device_supply():
Warning(drivers/regulator/core.c:912): missing initial short description on line:
* set_consumer_device_supply: Bind a regulator to a symbolic supply
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Singular Message is 16 bits:
DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
Current implementation return immedially after sucessfuly write MSB part.
To properly set mode, we need to write the complete message ( MSB and LSB ).
In twl.h, now we have defines for PM Master module register offsets,
use it instead of hard coded 0x15/0x16.
Use "message & 0xff" to ensure we send correct value for LSB.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Lesly Arackal Manuel <leslyam@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch add locks around regulator supply enable.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Integer division will truncate the result, this patch ensures we have
enough delay time for enabling regulator.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We already have device_remove_file() in error path,
no need to call it before goto link_name_err.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes a disable failure when regulator supply is used.
A while loop in regulator disable checks for supply pointer != NULL
but the pointer is not always updated, resulting in the while loop
running too many times causing a disable failure.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
A recurring complaint from CFS users is that parallel kbuild has
a negative impact on desktop interactivity. This patch
implements an idea from Linus, to automatically create task
groups. Currently, only per session autogroups are implemented,
but the patch leaves the way open for enhancement.
Implementation: each task's signal struct contains an inherited
pointer to a refcounted autogroup struct containing a task group
pointer, the default for all tasks pointing to the
init_task_group. When a task calls setsid(), a new task group
is created, the process is moved into the new task group, and a
reference to the preveious task group is dropped. Child
processes inherit this task group thereafter, and increase it's
refcount. When the last thread of a process exits, the
process's reference is dropped, such that when the last process
referencing an autogroup exits, the autogroup is destroyed.
At runqueue selection time, IFF a task has no cgroup assignment,
its current autogroup is used.
Autogroup bandwidth is controllable via setting it's nice level
through the proc filesystem:
cat /proc/<pid>/autogroup
Displays the task's group and the group's nice level.
echo <nice level> > /proc/<pid>/autogroup
Sets the task group's shares to the weight of nice <level> task.
Setting nice level is rate limited for !admin users due to the
abuse risk of task group locking.
The feature is enabled from boot by default if
CONFIG_SCHED_AUTOGROUP=y is selected, but can be disabled via
the boot option noautogroup, and can also be turned on/off on
the fly via:
echo [01] > /proc/sys/kernel/sched_autogroup_enabled
... which will automatically move tasks to/from the root task group.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Paul Turner <pjt@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
[ Removed the task_group_path() debug code, and fixed !EVENTFD build failure. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <1290281700.28711.9.camel@maggy.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
