The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.
This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.
Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
bit 0:
0 => 1 sd/mmc slot
1 => 2 sd/mmc slots connectors (board from revision C)
system_rev tested on Barebox commit d8f3ee103a9f4bd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The MTD nand driver for Atmel chips is atmel_nand and not at91_nand anymore.
Change wrong configuration variables that were remaining.
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Today the board use 2 machines id AT91SAM9G45EKES and AT91SAM9M10G45EK
now will use only AT91SAM9M10G45EK.
The other boards revision will be specified via system_rev.
for 9g45ekes, m10g45ekes and m10g45ek boards and revisions
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add an optional test to force long-term preemption of RCU read-side
critical sections, controlled by new test_boost, test_boost_interval,
and test_boost_duration module parameters. This is to be used to
test RCU priority boosting.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This addresses the following RCU lockdep splat:
[0.051203] CPU0: AMD QEMU Virtual CPU version 0.12.4 stepping 03
[0.052999] lockdep: fixing up alternatives.
[0.054105]
[0.054106] ===================================================
[0.054999] [ INFO: suspicious rcu_dereference_check() usage. ]
[0.054999] ---------------------------------------------------
[0.054999] kernel/sched.c:616 invoked rcu_dereference_check() without protection!
[0.054999]
[0.054999] other info that might help us debug this:
[0.054999]
[0.054999]
[0.054999] rcu_scheduler_active = 1, debug_locks = 1
[0.054999] 3 locks held by swapper/1:
[0.054999] #0: (cpu_add_remove_lock){+.+.+.}, at: [<ffffffff814be933>] cpu_up+0x42/0x6a
[0.054999] #1: (cpu_hotplug.lock){+.+.+.}, at: [<ffffffff810400d8>] cpu_hotplug_begin+0x2a/0x51
[0.054999] #2: (&rq->lock){-.-...}, at: [<ffffffff814be2f7>] init_idle+0x2f/0x113
[0.054999]
[0.054999] stack backtrace:
[0.054999] Pid: 1, comm: swapper Not tainted 2.6.35 #1
[0.054999] Call Trace:
[0.054999] [<ffffffff81068054>] lockdep_rcu_dereference+0x9b/0xa3
[0.054999] [<ffffffff810325c3>] task_group+0x7b/0x8a
[0.054999] [<ffffffff810325e5>] set_task_rq+0x13/0x40
[0.054999] [<ffffffff814be39a>] init_idle+0xd2/0x113
[0.054999] [<ffffffff814be78a>] fork_idle+0xb8/0xc7
[0.054999] [<ffffffff81068717>] ? mark_held_locks+0x4d/0x6b
[0.054999] [<ffffffff814bcebd>] do_fork_idle+0x17/0x2b
[0.054999] [<ffffffff814bc89b>] native_cpu_up+0x1c1/0x724
[0.054999] [<ffffffff814bcea6>] ? do_fork_idle+0x0/0x2b
[0.054999] [<ffffffff814be876>] _cpu_up+0xac/0x127
[0.054999] [<ffffffff814be946>] cpu_up+0x55/0x6a
[0.054999] [<ffffffff81ab562a>] kernel_init+0xe1/0x1ff
[0.054999] [<ffffffff81003854>] kernel_thread_helper+0x4/0x10
[0.054999] [<ffffffff814c353c>] ? restore_args+0x0/0x30
[0.054999] [<ffffffff81ab5549>] ? kernel_init+0x0/0x1ff
[0.054999] [<ffffffff81003850>] ? kernel_thread_helper+0x0/0x10
[0.056074] Booting Node 0, Processors #1lockdep: fixing up alternatives.
[0.130045] #2lockdep: fixing up alternatives.
[0.203089] #3 Ok.
[0.275286] Brought up 4 CPUs
[0.276005] Total of 4 processors activated (16017.17 BogoMIPS).
The cgroup_subsys_state structures referenced by idle tasks are never
freed, because the idle tasks should be part of the root cgroup,
which is not removable.
The problem is that while we do in-fact hold rq->lock, the newly spawned
idle thread's cpu is not yet set to the correct cpu so the lockdep check
in task_group():
lockdep_is_held(&task_rq(p)->lock)
will fail.
But this is a chicken and egg problem. Setting the CPU's runqueue requires
that the CPU's runqueue already be set. ;-)
So insert an RCU read-side critical section to avoid the complaint.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Using ACCESS_ONCE() to observe the jiffies_stall/rnp->qsmask value
due to the caller didn't hold the root_rcu/rnp node's lock. Although
use without ACCESS_ONCE() is safe due to the value loaded being used
but once, the ACCESS_ONCE() is a good documentation aid -- the variables
are being loaded without the services of a lock.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
CC: Dipankar Sarma <dipankar@in.ibm.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
> ===================================================
> [ INFO: suspicious rcu_dereference_check() usage. ]
> ---------------------------------------------------
> /home/greearb/git/linux.wireless-testing/kernel/sched.c:618 invoked rcu_dereference_check() without protection!
>
> other info that might help us debug this:
>
> rcu_scheduler_active = 1, debug_locks = 1
> 1 lock held by ifup/23517:
> #0: (&rq->lock){-.-.-.}, at: [<c042f782>] task_fork_fair+0x3b/0x108
>
> stack backtrace:
> Pid: 23517, comm: ifup Not tainted 2.6.36-rc6-wl+ #5
> Call Trace:
> [<c075e219>] ? printk+0xf/0x16
> [<c0455842>] lockdep_rcu_dereference+0x74/0x7d
> [<c0426854>] task_group+0x6d/0x79
> [<c042686e>] set_task_rq+0xe/0x57
> [<c042f79e>] task_fork_fair+0x57/0x108
> [<c042e965>] sched_fork+0x82/0xf9
> [<c04334b3>] copy_process+0x569/0xe8e
> [<c0433ef0>] do_fork+0x118/0x262
> [<c076302f>] ? do_page_fault+0x16a/0x2cf
> [<c044b80c>] ? up_read+0x16/0x2a
> [<c04085ae>] sys_clone+0x1b/0x20
> [<c04030a5>] ptregs_clone+0x15/0x30
> [<c0402f1c>] ? sysenter_do_call+0x12/0x38
Here a newly created task is having its runqueue assigned. The new task
is not yet on the tasklist, so cannot go away. This is therefore a false
positive, suppress with an RCU read-side critical section.
Reported-by: Ben Greear <greearb@candelatech.com
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Ben Greear <greearb@candelatech.com
call request_firmware instead of trying to open the file directly from
the kernel driver.
Signed-off-by: Marek Belisko <marek.belisko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the device name has changed use the new name to
bind the driver to it.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added connection status report for the case connection fails.
Originally this logic was missing.
Signed-off-by: Nohee Ko <noheek@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed duplicated file, linux_osl.c from brcmfmac.
linux_osl.c under brcm80211/util/ will be shared
between softmac & fullmac drivers
Signed-off-by: Nohee Ko <noheek@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-drop in_precision in favor of new in_type -
This also fixes the bug from the scan elements move (as a side effect)
-add sign and storagebits to struct ad799x_chip_info
-properly mask the results based on ad799x_chip_info:bits
staging: iio: adc: ad799x misc fixed per iio list review
remove new line
remove storagebits from struct ad799x_chip_info
use defined storagebits value for in_type
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device found passed to the attr functions is that of the ring
buffer, not the the iio_dev so we need to bounce through one more
hop to get the right address.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device found passed to the attr functions is that of the ring
buffer, not the the iio_dev so we need to bounce through one more
hop to get the right address.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 5ed3bc7288.
It turns-out that not all drivers are calling ieee80211_tx_status from a
compatible context. Revert this for now and try again later...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 030725d2c7.
This commit relies on commit 5ed3bc7288
("mac80211: use netif_receive_skb in ieee80211_tx_status callpath")
Unfortunately not all drivers are calling ieee80211_tx_status from a
compatible context, so that commit needs to be reverted in 2.6.36.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to update the issue_seq on any grant operation, be it via an MDS
reply or a separate grant message. The update in the grant path was
missing. This broke cap release for inodes in which the MDS sent an
explicit grant message that was not soon after followed by a successful
MDS reply on the same inode.
Also fix the signedness on seq locals.
Signed-off-by: Sage Weil <sage@newdream.net>
If an MDS tries to revoke caps that we don't have, we want to send
releases early since they probably contain the caps message the MDS
is looking for.
Previously, we only sent the messages if we didn't have the inode either. But
in a multi-mds system we can retain the inode after dropping all caps for
a single MDS.
Signed-off-by: Greg Farnum <gregf@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
encode_fh on error should update max_len with minimum required
size, so that caller can redo the call with the reallocated buffer.
This is required with open by handle patch series
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Sage Weil <sage@newdream.net>
encode_fh function should return 255 on error as done by other file
system to indicate EOVERFLOW. Also max_len is in sizeof(u32) units
and not in bytes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Sage Weil <sage@newdream.net>
If we interrupt an osd request, we call __cancel_request, but it wasn't
verifying that req->r_osd was non-NULL before dereferencing it. This could
cause a crash if osds were flapping and we aborted a request on said osd.
Reported-by: Henry C Chang <henry_c_chang@tcloudcomputing.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Add missing #inclusion of <linux/irq.h>. Without it, the following error can
occur with the irqflags fixup patches applied:
drivers/net/smc91x.c: In function 'smc_probe':
drivers/net/smc91x.c:1987:2: error: implicit declaration of function 'irq_canonicalize'
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Drop inclusions of asm/system.h from linux/hardirq.h and linux/list.h as
they're no longer required and prevent the M68K arch's IRQ flag handling macros
from being made into inlined functions due to circular dependencies.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add missing consts to the sys_execve() declaration which result in the
following error:
arch/sh/kernel/process_32.c:303: error: conflicting types for 'sys_execve'
/warthog/nfs/linux-2.6-fscache/arch/sh/include/asm/syscalls_32.h:24: error: previous declaration of 'sys_execve' was here
Signed-off-by: David Howells <dhowells@redhat.com>
Rename h/w IRQ flags handling functions to be in line with what is expected for
the irq renaming patch. This renames local_*_hw() to hard_local_*() using the
following perl command:
perl -pi -e 's/local_irq_(restore|enable|disable)_hw/hard_local_irq_\1/ or s/local_irq_save_hw([_a-z]*)[(]flags[)]/flags = hard_local_irq_save\1()/' `find arch/blackfin/ -name "*.[ch]"`
and then fixing up asm/irqflags.h manually.
Additionally, arch/hard_local_save_flags() and arch/hard_local_irq_save() both
return the flags rather than passing it through the argument list.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a missing dependency (mach/blackfin.h) to asm/irqflags.h so that
bfin_read_IMASK() can be used by inline functions.
Signed-off-by: David Howells <dhowells@redhat.com>
Rename the PC2() symbol in the generic DES crypto module to be prefixed with
DES_ to avoid collision with arch code (Blackfin in this case).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Split the BF532 machine type BFIN_*_FIO_FLAG() functions to their own header
file to avoid circular #include problems as these functions require IRQ flag
handling, which requires asm/blackfin.h, which otherwise requires the header
file that defines these functions.
For good measure, also get rid of the inclusion of asm/blackfin.h from
mach/cdefBF532.h (which is circular) and defBF532.h (which is included by
asm/blackfin.h before including this header).
Signed-off-by: David Howells <dhowells@redhat.com>
Split the PLL control code from the Blackfin machine-specific cdef headers so
that the irqflags functions can be renamed without incurring a header loop.
Signed-off-by: David Howells <dhowells@redhat.com>
A physically mapped hardware status page is allocated at driver load
time but was never freed. Call the existing code to free this page at
driver unload time on hardware which uses this kind.
Signed-off-by: Keith Packard <keithp@keithp.com>
[ickle: call before tearing down registers on KMS-only path, as pointed
out by Dave Airlie]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
When we call the slab shrinker to free a page we need to stop at
page count one because the caller always holds a single reference, not zero.
This avoids useless looping over slab shrinkers and freeing too much
memory.
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The SIGBUS user space signalling is supposed to report the
address granuality of a corruption. Pass this information correctly
for huge pages by querying the hpage order.
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The original hwpoison code added a new siginfo field si_addr_lsb to
pass the granuality of the fault address to user space. Unfortunately
this field was never copied to user space. Fix this here.
I added explicit checks for the MCEERR codes to avoid having
to patch all potential callers to initialize the field.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The page-types utility still uses an out of date name for the
unpoison interface: debugfs:hwpoison/renew-pfn
This patch renames and fixes it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
2.6.36 introduces an API for drivers to switch the IO scheduler
instead of manually calling the elevator exit and init functions.
This API was added since q->elevator must be cleared in between
those two calls. And since we already have this functionality
directly from use by the sysfs interface to switch schedulers
online, it was prudent to reuse it internally too.
But this API needs the queue to be in a fully initialized state
before it is called, or it will attempt to unregister elevator
kobjects before they have been added. This results in an oops
like this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000051
IP: [<ffffffff8116f15e>] sysfs_create_dir+0x2e/0xc0
PGD 47ddfc067 PUD 47c6a1067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:02.0/0000:04:00.1/irq
CPU 2
Modules linked in: t(+) loop hid_apple usbhid ahci ehci_hcd uhci_hcd libahci usbcore nls_base igb
Pid: 7319, comm: modprobe Not tainted 2.6.36-rc6+ #132 QSSC-S4R/QSSC-S4R
RIP: 0010:[<ffffffff8116f15e>] [<ffffffff8116f15e>] sysfs_create_dir+0x2e/0xc0
RSP: 0018:ffff88027da25d08 EFLAGS: 00010246
RAX: ffff88047c68c528 RBX: 00000000fffffffe RCX: 0000000000000000
RDX: 000000000000002f RSI: 000000000000002f RDI: ffff88047e196c88
RBP: ffff88027da25d38 R08: 0000000000000000 R09: d84156c5635688c0
R10: d84156c5635688c0 R11: 0000000000000000 R12: ffff88047e196c88
R13: 0000000000000000 R14: 0000000000000000 R15: ffff88047c68c528
FS: 00007fcb0b26f6e0(0000) GS:ffff880287400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000051 CR3: 000000047e76e000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process modprobe (pid: 7319, threadinfo ffff88027da24000, task ffff88027d377090)
Stack:
ffff88027da25d58 ffff88047c68c528 00000000fffffffe ffff88047e196c88
<0> ffff88047c68c528 ffff88047e05bd90 ffff88027da25d78 ffffffff8123fb77
<0> ffff88047e05bd90 0000000000000000 ffff88047e196c88 ffff88047c68c528
Call Trace:
[<ffffffff8123fb77>] kobject_add_internal+0xe7/0x1f0
[<ffffffff8123fd98>] kobject_add_varg+0x38/0x60
[<ffffffff8123feb9>] kobject_add+0x69/0x90
[<ffffffff8116efe0>] ? sysfs_remove_dir+0x20/0xa0
[<ffffffff8103d48d>] ? sub_preempt_count+0x9d/0xe0
[<ffffffff8143de20>] ? _raw_spin_unlock+0x30/0x50
[<ffffffff8116efe0>] ? sysfs_remove_dir+0x20/0xa0
[<ffffffff8116eff4>] ? sysfs_remove_dir+0x34/0xa0
[<ffffffff81224204>] elv_register_queue+0x34/0xa0
[<ffffffff81224aad>] elevator_change+0xfd/0x250
[<ffffffffa007e000>] ? t_init+0x0/0x361 [t]
[<ffffffffa007e000>] ? t_init+0x0/0x361 [t]
[<ffffffffa007e0a8>] t_init+0xa8/0x361 [t]
[<ffffffff810001de>] do_one_initcall+0x3e/0x170
[<ffffffff8108c3fd>] sys_init_module+0xbd/0x220
[<ffffffff81002f2b>] system_call_fastpath+0x16/0x1b
Code: e5 41 56 41 55 41 54 49 89 fc 53 48 83 ec 10 48 85 ff 74 52 48 8b 47 18 49 c7 c5 00 46 61 81 48 85 c0 74 04 4c 8b 68 30 45 31 f6 <41> 80 7d 51 00 74 0e 49 8b 44 24 28 4c 89 e7 ff 50 20 49 89 c6
RIP [<ffffffff8116f15e>] sysfs_create_dir+0x2e/0xc0
RSP <ffff88027da25d08>
CR2: 0000000000000051
---[ end trace a6541d3bf07945df ]---
Fix this by adding a registered bit to the elevator queue, which is
set when the sysfs kobjects have been registered.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Use the new infrastructure to balance interrupts for flow
alignment when ATR or Flow Director are enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>