Disable plcp error checking for 6000g2b devices, with wifi/bt coex;
this got trigger too often, disable for now until finding better
trigger point.
Also extend the firmware reload timer much longer for BT coex to make sure
there are will be no mistake to reload firmware too fast and too often.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BT SCO needs to be re-applied to the device,
while the traffic load just needs to be correct
in software.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS doesn't allow for coexistence, so it
should be disabled.
Additionally, disable reacting to the BT
profile notification when in IBSS mode,
it likely won't be sent by the device to
start with though.
Also, in IBSS mode, BT coexistence isn't as fully-featured
and we must use a single antenna only. So instead of
peppering the code with new checks, simply pretend
we are in high BT traffic load, which has the needed
effect of disabling antenna B use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we turn off the device, reset BT
data so that we don't have outdated
information when we come up again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Depending on the amount of bluetooth traffic,
using the shared antenna (antenna B) will have
adverse impact on both bluetooth and wireless
traffic. Add controls to improve the situation
by making rate scaling depend on the BT load.
When there's high bluetooth traffic load, there's
little point in trying to aggregate as BT traffic
would disrupt the aggregated frames all the time,
so simply don't start sessions then.
When BT traffic returns to lower levels, the rate
scaling will come here again automatically when
wifi traffic is high enough, and then it will be
able to successfully enable aggregation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When advanced bt coex enabled, uCode will send bt status
notification to driver, here add support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BT ignore bit should be set when transmitting
auth, assoc response and eap frames.
Also, scanning should set the BT ignore bit for the
probe request transmission; Note that we only use
the non-shared antenna.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
6000g2b hardware implements advance bluetooth coexist command,
implement base on the new API command strucutre.
Also increment the API 5 to support the advance BT/WIfi coex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new 6000g2b hardware requires a different
bluetooth coexist implementation on the host,
this adds the command/notification definitions
for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No code or function changes, just some cleanup work for
out-of-date comments
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No functional changes, update comments to match current file structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unlike most other workqueue-tasks, the restart_work is
not scheduled onto mac80211's private per-interface
workqueue, but onto one of the system-wide workqueues.
Therefore the mac80211-stack has to cancel any pending
restarts, before destroying the shared device context
and handing back the memory. Otherwise - under very
unlucky circumstances - there could be a stale work-
item left, because some other kernel component might
have delayed the execution of ieee80211_restart_work
for too long.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ISL3887 chip needs a USB reset, whenever the
usb-frontend module "p54usb" is reloaded.
This patch fixes an off-by-one bug, if the user
is running a kernel without the CONFIG_PM option
set and for some reason (e.g.: compat-wireless)
wants to switch between different p54usb modules.
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As my nokia address doesn't work anymore, it's better just to remove the
copyright contact altogether. We have MODULE_AUTHOR() scripts for these
anyway.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano should be the contact person for the include/linux/spi/wl12xx.h file.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an Kconfig option, which allows the user
to select, whenever he/she wants to include a 4k blob for
generic calibration and interface values into the driver,
or cut the module size by about 15 to 20%.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Descriptors are currently logged with ATH5K_DEBUG_RESET,
which isn't really apt, and also means we can't see just
the descriptor setup or just the resets. Add a new
debug level just for that.
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some comments:
s/transmition/transmission/
s/puting/putting/
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix spelling and readability of a few lines of kernel doc:
s/issueing/issuing/g
s/approriate/appropriate/g
s/supported by simply/supported simply by/
s/IEEE80211_HW_BEACON_FILTERING/IEEE80211_HW_BEACON_FILTER/g
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mesh_hdr only used when CONFIG_MAC80211_MESH is defined
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: David Gibson <hermes@gibson.dropbear.id.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix walking past the end of the bitrate_table array
in the case when the loop counter == BITRATE_TABLE_SIZE.
Reported by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make del_timer_sync() works we have to assure that timer function
does not rearm the timer. To achieve that we cancel timer with
STATUS_EXIT_PENDING bit set in __iwl{3945,}_down function.
Patch also fix priv->txq memory usage after free for iwl3945, because
it move timer cancellation before iwl3945_hw_txq_ctx_free(priv) is called.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RCU now has a public git tree, so add it via the T: line in the
MAINTAINERS file.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: joe@perches.com
LKML-Reference: <20100825155850.GA6601@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ioctl path and the scsi tape path were not accounting
for their additions to the queue depth.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86, Pentium4: Clear the P4_CCCR_FORCE_OVF flag
tracing/trace_stack: Fix stack trace on ppc64
It wasn't setting the ms.has_children for the hist_entry itself, just
for the callchain
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
Eliminate sparse warning - bad constant expression
cifs: check for NULL session password
missing changes during ntlmv2/ntlmssp auth and sign
[CIFS] Fix ntlmv2 auth with ntlmssp
cifs: correction of unicode header files
cifs: fix NULL pointer dereference in cifs_find_smb_ses
cifs: consolidate error handling in several functions
cifs: clean up error handling in cifs_mknod
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, tsc, sched: Recompute cyc2ns_offset's during resume from sleep states
sched: Fix rq->clock synchronization when migrating tasks
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: handle events as edge-triggered
xen: use percpu interrupts for IPIs and VIRQs
* '2.6.36-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/xfsdev:
xfs: do not discard page cache data on EAGAIN
xfs: don't do memory allocation under the CIL context lock
xfs: Reduce log force overhead for delayed logging
xfs: dummy transactions should not dirty VFS state
xfs: ensure f_ffree returned by statfs() is non-negative
xfs: handle negative wbc->nr_to_write during sync writeback
writeback: write_cache_pages doesn't terminate at nr_to_write <= 0
xfs: fix untrusted inode number lookup
xfs: ensure we mark all inodes in a freed cluster XFS_ISTALE
xfs: unlock items before allowing the CIL to commit
No need to call input_free_device() after input_unregister_device().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Introduced by 987a6c0298 a swap in max/min
calculation gets fixed by this patch.
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Huaxu and Rudolf want me to be the hwmon coretemp driver maintainer and
remove their names from the coretemp maintainer entry.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix
temperature reporting for ASB1 processor revisions) fixed temperature
reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f)
were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit
leads to wrong temperature reporting for AM2 CPU parts.
The solution is to determine the package type for models 0x6b, 0x6f,
0x7f.
This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See
"Constructing the processor Name String" in "Revision Guide for AMD
NPT Family 0Fh Processors" (Rev. 3.46).
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x]
Reported-by: Vladislav Guberinic <neosisani@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix the following build warning:
CC [M] drivers/hwmon/coretemp.o
drivers/hwmon/coretemp.c: In function "coretemp_init":
drivers/hwmon/coretemp.c:521: warning: unused variable "n"
drivers/hwmon/coretemp.c:521: warning: unused variable "p"
Introduced by commit 851b29cb3b. When
you drop code, you also have to drop the variables this code was
using.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
The "priv" allocated in pxa_ssp_probe() should be kfreed in pxa_ssp_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If on Pentium4 CPUs the FORCE_OVF flag is set then an NMI happens
on every event, which can generate a flood of NMIs. Clear it.
Reported-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make special HID devices' Kconfig names unambiguous, obviating the need
to enter the help menu of each driver in order to know what hardware
device it actually supports.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Stephane Chatty <chatty@enac.fr>
Cc: Don Prince <dhprince-devel@yahoo.co.uk>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes the following build warning introduced by the
callchain rework:
arch/x86/kernel/cpu/perf_event.c:1574: warning: ‘perf_callchain_entry_nmi’ defined but not used
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1282718949.16443.75.camel@minggr.sh.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As reported by Anton Blanchard when we use
percpu_counter_read_positive() to make our orphan socket limit checks,
the check can be off by up to num_cpus_online() * batch (which is 32
by default) which on a 128 cpu machine can be as large as the default
orphan limit itself.
Fix this by doing the full expensive sum check if the optimized check
triggers.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>