This helps us debug channel changes better.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a video head and keyboard are hooked up, specifying "console=ttyS0"
or similar to use a serial console will not work properly.
The key issue is that we must register all serial console capable
devices with register_console(), otherwise the command line specified
device won't be found. The sun serial drivers would only register
themselves as console devices if the OpenFirmware specified console
device node matched. To fix this part we now unconditionally get
the serial console register by setting serial_drv->cons always.
Secondarily we must not add_preferred_console() using the firmware
provided console setting if the user gaven an override on the kernel
command line using "console=" The "primary framebuffer" matching
logic was always triggering o n openfirmware device node match, make
it not when a command line override was given.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in client mode and associating to an AP, the channel
change is usually performed with the offchannel flag still set.
However after the assoc is complete, the following channel change event
is suppressed because the run time channel is already set to the operating channel.
Fix this by sending channel change notifications to the driver even if
only the offchannel flag changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function was exiting early if the existing diversity settings
were unchanged. Unfortunately, in some cases the antenna configuration
is not initialized at all.
https://bugzilla.kernel.org/show_bug.cgi?id=14751
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
The RX and TX directions were inverted.
Reported-by: Seungwhan Youn <claude.youn@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
...and unregistration to core shutdown. Previously, the driver
remained registered even when the hardware was shutdown. That
causes the driver to return -ENODEV if the b43 device is IFF_DOWN.
This change causes the driver to disappear in that case, allowing
/dev/hwrng to still function if another hwrng device is available.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwmc3200wifi/rx.c: In function 'iwm_ntf_wifi_if_wrapper':
drivers/net/wireless/iwmc3200wifi/rx.c:1198: warning: comparison is always true due to limited range of data type
This is, of course, because the value of WIFI_IF_NTFY_MAX is 0xff and
hdr->oid is a u8. This is obviously an attempt to verify the range on
an input value, but since it has no effect it can simply be removed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
drivers/net/wireless/ipw2x00/ipw2100.c: In function 'ipw2100_tx_send_commands':
drivers/net/wireless/ipw2x00/ipw2100.c:3063: warning: cast to pointer from integer of different size
This changes the cast and the conversion to match other usage of the
same value in calls to IPW_DEBUG_TX.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some iwlwifi devices inexplicably disconnect themselves from the PCI-E
bus causing the predictable failures. This seems to disappear if ASPM
is disabled.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This provides a little more flexibility for human users, and it allows
us to use isalpha rather than the custom is_alpha_upper.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implement basic infrastructure to support use of NAPI by
mac80211-based hardware drivers.
Because mac80211 devices can support multiple netdevs, a dummy netdev
is used for interfacing with the NAPI code in the core of the network
stack. That structure is hidden from the hardware drivers, but the
actual napi_struct is exposed in the ieee80211_hw structure so that the
poll routines in drivers can retrieve that structure. Hardware drivers
can also specify their own weight value for NAPI polling.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the information available through ethtool...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
Get rid of some nesting and add a label we can goto on error.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Like others in the Mini series, the Dell Mini 1012 does not support
the smbios hook required by dell-laptop.
Signed-off-by: Victor van den Elzen <victor.vde@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
On the T410s and most likely other current models, Fn-F6 is labeled as
Camera/Headphone key. Report key presses as KEY_CAMERA.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Acked-by: Jerone Young <jerone.young@canonical.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Use the quirks engine to select model-specific keymaps, which makes
it much easier to extend should we need it.
Keycodes are based on the tables at
http://www.thinkwiki.org/wiki/Default_meanings_of_special_keys.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Use a safer coding style for the hotkey keymap. This does not fix any
problems, as the current code is correct. But it might help avoid
mistakes in the future.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
acpi_video_backlight_support() already tells us if ACPI is handling
backlight control through the generic ACPI handle. It is better to just
trust it.
While at it, adjust down a printk priority, and test earlier for
brightness_enable=0.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The Linux ACPI core locates the ACPI video devices for us and marks them
with ACPI_VIDEO_HID. Use that information to locate the video device
instead of a half-baked hunt for _BCL.
This uncouples the detection of the number of backlight brightness
levels on ThinkPads from the ACPI paths in vid_handle.
With this change, the driver should be able to always detect whether the
ThinkPad uses a 8-level or 16-level brightness scale even on newer
models for which the vid_handle paths have not been updated yet.
It will skip deactivated devices in the ACPI device tree, which is a
change in behaviour.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There is a potential NULL dereference of "limits." We can just return
NULL earlier to avoid it. The caller already handles NULL returns.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The assignment of ret to -EIO appears to only make sense if the branch that
it is aligned with is executed, so move it into that branch.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The JooJoo tablet (http://thejoojoo.com/) contains an "eGalax Inc. USB
TouchController", and this patch hooks it up to the egalax-touch driver.
Without the patch we don't get any cursor motion, since it comes through
Z/RX rather than X/Y.
(The egalax-touch driver does not yet generate a correct event sequence
for the "serial" protocol used by this device, though -- see the note
added to the code, which comes from research by Stéphane Chatty.)
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Stéphane Chatty <chatty@enac.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As part of ongoing effort to reduce the coupling with libnewt, browsers
are being changed to return the exit key.
The annotate browser is not returning it as expected by builtin-annotate
when annotating multiple symbols (when 'perf annotate' is called without
specifying a symbol name).
Fix it by returning the exit key and also adding the RIGHT key as a exit
key so that going to the next symbol in the TUI can work again.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The below updates a broken web address to one(hopefully) thats
the new correct address.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
kernel-parameters.txt lists 'noreplace-paravirt' parameter as being
limited to X86-32, which is incorrect -- it's actually supported by
x86-32, x86-64 and ia-64.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Last change I did made a big mess in function names and CONFIG names,
this patch fixes this so that the baseboard support is really built
when selected.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is not supported by current hardware revisions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
wq->rescuer is not freed when wq is destroyed, leads a memory leak
then. This patch also remove a redundant line.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Commit 5a5f561 (convert OMAP3 PRCM macros to the _SHIFT/_MASK suffixes)
mistakenly removed the check for PER when disabling the IO chain.
During idle, if the PER powerdomain transitions into a lower state
and CORE does not, the IO pad wakeups are not being disabled in
the idle path after they are enabled. This can happen with the
lower C-states when using CPUidle for example.
This patch ensures that the check for disabling IO wakeups also checks
for PER transitions, matching the check done to enable IO wakeups.
Found when debugging PM/CPUidle related problems reported by Ameya
Palande <ameya.palande@nokia.com>. Problems were triggered
particularily on boards with UART2 consoles (n900, Overo) since UART2
is in the PER powerdomain.
Tested on l-o master (omap3_defonfig + CONFIG_CPU_IDLE=y) as well
as with current PM branch. Boards tested: n900, Overo, omap3evm.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@nokia.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description to clarify the transistion]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit ffb63e3402 changed
Kconfig to select support for omap2, 3 and 4 by default.
However, CONFIG_SMP won't currently work properly on
uniprocessor ARMs, or if support for earlier ARM cores
is selected in.
Fix this by updating omap_4430sdp_defconfig to not
select omap2 or 3 at this point.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Otherwise we get the following error when enabling CONFIG_SMP
for omap3_defconfig:
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ipi r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ltirq r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ipi r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ltirq r0,r6,r5,lr'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Otherwise we get the following error with omap3_defconfig and CONFIG_SMP:
Error: selected processor does not support `sev'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This reverts commit 1235f504aa.
It causes regressions worse than the problem it was trying
to fix. Eric will try to solve the problem another way.
Signed-off-by: David S. Miller <davem@davemloft.net>
cpu_is_omap3517() and cpu_is_omap3505() are the subgroups of cpu_is_omap34xx(),
so we should check cpu_is_omap3517() and cpu_is_omap3505() first, then check
cpu_is_omap34xx().
Otherwise, All AM35XX (Sitara) clocks do not get registered and device drivers
(ti_hecc, etc...) that depend on those clocks are failing to get the clock and
end up with non working device.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong placement of break causes all revisions of 3630 to be
detected as 3630 es1.2, we need to break main loop if we have
an identified chip, default falls through as in the rest of the
switches in this function.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Manjunath K <manjugk@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>