Firmware may return wlan_failure when deactivating a BSS that is already
inactive. This is a valid teardown case and should not fail the remove
path.
Keep activation failures unchanged since they still indicate that firmware
failed to create or activate the BSS state.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20260425195011.790265-13-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable PCIe ASPM unconditionally for MT7927. The CONNINFRA power
domain and WFDMA register access are unreliable with PCIe L1 active,
causing throughput to drop from 1+ Gbps to ~200 Mbps.
Disable runtime PM and deep sleep for MT7927. The combo chip shares
a CONNINFRA power domain between WiFi (PCIe) and BT (USB).
SET_OWN/CLR_OWN transitions on the LPCTL register crash the BT
firmware, requiring a full power cycle to recover. PM enablement will
be addressed in a follow-up once safe power state transitions are
determined.
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-10-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The mac_reset and resume paths use the hardcoded MT_INT_RX_DONE_ALL
constant (bits 0-2) to re-enable RX interrupts. This is correct for
MT7925 (RX rings 0, 1, 2) but wrong for chips using different ring
indices.
Define a per-chip irq_map with the correct RX interrupt enable bits and
replace hardcoded MT_INT_RX_DONE_ALL with irq_map field reads in the
resume and mac_reset paths. Add the MT7927 irq_map with interrupt bits
matching its RX ring layout (rings 4, 6, 7), selected at probe time
based on PCI device ID.
This ensures the correct interrupt bits are enabled regardless of the
chip variant.
Tested-by: Marcin FM <marcin@lgic.pl>
Tested-by: Cristian-Florin Radoi <radoi.chris@gmail.com>
Tested-by: George Salukvadze <giosal90@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Tested-by: Samu Toljamo <samu.toljamo@gmail.com>
Tested-by: Ariel Rosenfeld <ariel.rosenfeld.750@gmail.com>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Thibaut François <tibo@humeurlibre.fr>
Tested-by: 张旭涵 <Loong.0x00@gmail.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-9-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add firmware path definitions for MT7927 WiFi firmware (WIFI_RAM_CODE
and PATCH_MCU) and the corresponding MODULE_FIRMWARE declarations. Add
MT7927 cases to mt792x_ram_name() and mt792x_patch_name() so the driver
loads the correct firmware for the 0x7927 chip ID.
PCI device table entries are deferred to a later patch to allow
infrastructure setup before device enablement.
Tested-by: Marcin FM <marcin@lgic.pl>
Tested-by: Cristian-Florin Radoi <radoi.chris@gmail.com>
Tested-by: George Salukvadze <giosal90@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Tested-by: Samu Toljamo <samu.toljamo@gmail.com>
Tested-by: Ariel Rosenfeld <ariel.rosenfeld.750@gmail.com>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Thibaut François <tibo@humeurlibre.fr>
Tested-by: 张旭涵 <Loong.0x00@gmail.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-8-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MediaTek MT7927 (Filogic 380) combo chip uses MT7927 WiFi silicon
that is architecturally compatible with MT7925. Extend is_mt7925() to
match chip ID 0x7927, and add is_mt7927() for code paths that need
MT7927-specific handling.
Also add 0x7927 to is_mt76_fw_txp() to match MT7925's TXP format.
Tested-by: Marcin FM <marcin@lgic.pl>
Tested-by: Cristian-Florin Radoi <radoi.chris@gmail.com>
Tested-by: George Salukvadze <giosal90@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Tested-by: Samu Toljamo <samu.toljamo@gmail.com>
Tested-by: Ariel Rosenfeld <ariel.rosenfeld.750@gmail.com>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Thibaut François <tibo@humeurlibre.fr>
Tested-by: 张旭涵 <Loong.0x00@gmail.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-7-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7925_init_eht_caps() only populates EHT MCS/NSS maps for BW <= 80
and BW = 160, but never sets BW = 320. This means iw phy shows no
320MHz MCS map entries even though the hardware supports 320MHz
operation in the 6GHz band.
Add the missing 320MHz capability bits for 6GHz:
- PHY_CAP0: IEEE80211_EHT_PHY_CAP0_320MHZ_IN_6GHZ
- PHY_CAP1: beamformee SS for 320MHz
- PHY_CAP2: sounding dimensions for 320MHz
- PHY_CAP6: MCS15 support for 320MHz width
- MCS/NSS: populate bw._320 maps for 6GHz band
Introduce is_320mhz_supported() to gate 320MHz on MT7927 only, since
MT7925 does not support 320MHz operation.
Tested-by: Marcin FM <marcin@lgic.pl>
Tested-by: Cristian-Florin Radoi <radoi.chris@gmail.com>
Tested-by: George Salukvadze <giosal90@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Tested-by: Samu Toljamo <samu.toljamo@gmail.com>
Tested-by: Ariel Rosenfeld <ariel.rosenfeld.750@gmail.com>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Thibaut François <tibo@humeurlibre.fr>
Tested-by: 张旭涵 <Loong.0x00@gmail.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-6-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The sta_rec_eht structure has a mcs_map_bw320 field, and the channel
width mapping includes NL80211_CHAN_WIDTH_320, but the 320MHz MCS/NSS
map was never copied from the station's EHT capabilities to the MCU TLV.
This prevents negotiation of 320MHz channel width even when both the
hardware and firmware advertise support for it.
Add the missing memcpy for the 320MHz MCS map, matching the existing
pattern for BW20, BW80, and BW160.
Tested-by: Marcin FM <marcin@lgic.pl>
Tested-by: Cristian-Florin Radoi <radoi.chris@gmail.com>
Tested-by: George Salukvadze <giosal90@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Tested-by: Samu Toljamo <samu.toljamo@gmail.com>
Tested-by: Ariel Rosenfeld <ariel.rosenfeld.750@gmail.com>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Thibaut François <tibo@humeurlibre.fr>
Tested-by: 张旭涵 <Loong.0x00@gmail.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-5-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The RX vector (RXV) and TX status (TXS) parsing in mac.c lack handling
for 320MHz channel width. When the hardware reports 320MHz in the
bandwidth field, mt7925_mac_fill_rx_rate() returns -EINVAL and
mt7925_mac_add_txs_skb() records no bandwidth stats.
Add IEEE80211_STA_RX_BW_320 cases to both functions. The RXV parser
also handles BW_320+1 since the hardware can report 320MHz in two
adjacent encoding positions.
Tested-by: Marcin FM <marcin@lgic.pl>
Tested-by: Cristian-Florin Radoi <radoi.chris@gmail.com>
Tested-by: George Salukvadze <giosal90@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Tested-by: Samu Toljamo <samu.toljamo@gmail.com>
Tested-by: Ariel Rosenfeld <ariel.rosenfeld.750@gmail.com>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Thibaut François <tibo@humeurlibre.fr>
Tested-by: 张旭涵 <Loong.0x00@gmail.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-4-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
bss_rlm_tlv() in mt7925_mcu_bss_rlm_tlv() has no case for
NL80211_CHAN_WIDTH_320. When associated to a 320MHz BSS, the switch
falls through to default and sends bw=0 (CMD_CBW_20MHZ) to firmware
via BSS_RLM TLV. Firmware then configures the RX radio for 20MHz
and cannot decode the AP's 320MHz frames, resulting in complete data
path failure at 320MHz.
Add the missing NL80211_CHAN_WIDTH_320 case with CMD_CBW_320MHZ and
center_chan2.
Tested on ASUS RT-BE92U: 320MHz throughput goes from 0 Mbps to
841 Mbps (iperf3 -t30 -P8), PHY 4803 Mbps EHT-MCS11.
Reported-by: 张旭涵 <Loong.0x00@gmail.com>
Closes: https://github.com/openwrt/mt76/issues/927
Tested-by: 张旭涵 <Loong.0x00@gmail.com>
Tested-by: Marcin FM <marcin@lgic.pl>
Tested-by: Cristian-Florin Radoi <radoi.chris@gmail.com>
Tested-by: George Salukvadze <giosal90@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Tested-by: Samu Toljamo <samu.toljamo@gmail.com>
Tested-by: Ariel Rosenfeld <ariel.rosenfeld.750@gmail.com>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Thibaut François <tibo@humeurlibre.fr>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-3-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the error path of mt7925_change_vif_links(), the free: label iterates
over link_ids to clean up, but compares against `mconf` and `mlink`
which hold stale values from the last loop iteration rather than the
current link_id being freed.
Use array-indexed access (mconfs[link_id] / mlinks[link_id]) to compare
against the correct per-link pointers.
Fixes: 69acd6d910 ("wifi: mt76: mt7925: add mt7925_change_vif_links")
Tested-by: Marcin FM <marcin@lgic.pl>
Tested-by: Cristian-Florin Radoi <radoi.chris@gmail.com>
Tested-by: George Salukvadze <giosal90@gmail.com>
Tested-by: Evgeny Kapusta <3193631@gmail.com>
Tested-by: Samu Toljamo <samu.toljamo@gmail.com>
Tested-by: Ariel Rosenfeld <ariel.rosenfeld.750@gmail.com>
Tested-by: Chapuis Dario <chapuisdario4@gmail.com>
Tested-by: Thibaut François <tibo@humeurlibre.fr>
Tested-by: 张旭涵 <Loong.0x00@gmail.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Javier Tia <floss@jetm.me>
Link: https://patch.msgid.link/20260425195011.790265-2-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When MT76_NPU and CONFIG_NET_MEDIATEK_SOC_WED are enabled and
mt76 detects properly the Airoha NPU SoC, mt7996_init_tx_queues() will
dereference a NULL WED pointer.
Fix the issue by always passing the WED pointer from mt7996_dma_init().
Fixes: cd7951f242 ("wifi: mt76: mt7996: Integrate MT7990 dma configuration for NPU")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260418-mt7996-dma-init-npu-fix-v1-1-6b8dcffbcb57@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Having this unset breaks remain-on-channel and mgmt TX.
Move setting it to mt76 core to keep it in one place.
Fixes: 69d54ce749 ("wifi: mt76: mt7996: switch to single multi-radio wiphy")
Link: https://patch.msgid.link/20260324154904.2555603-2-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During hardware restart, link_id can be IEEE80211_LINK_UNSPECIFIED,
causing an out-of-bounds array access on msta->link[].
Add mt7996_sta_link() and mt7996_sta_link_protected() helper functions
for accessing sta links with proper RCU handling and bounds checking.
Use them for any sta link RCU access.
Reported-by: Chad Monroe <chad@monroe.io>
Link: https://patch.msgid.link/20260324154904.2555603-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260430083335.215239-6-johan@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260430083335.215239-5-johan@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260430083335.215239-4-johan@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260430083335.215239-3-johan@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver core holds a reference to the USB interface and its parent USB
device while the interface is bound to a driver and there is no need to
take additional references unless the structures are needed after
disconnect.
Drop the redundant device reference to reduce cargo culting, make it
easier to spot drivers where an extra reference is needed, and reduce
the risk of memory leaks when drivers fail to release it.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260430083335.215239-2-johan@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_put_vif_phy_link() frees the offchannel mlink with plain kfree()
after rcu_assign_pointer(NULL). However, rcu_assign_pointer only prevents
future RCU readers from obtaining the pointer -- it does not wait for
existing readers that already hold it via rcu_dereference.
The TX datapath (e.g. mt7996_mac_write_txwi) dereferences mlink->wcid
and mlink->idx under rcu_read_lock. If a TX softirq obtained the pointer
via rcu_dereference just before the NULL assignment, it will dereference
freed memory after the kfree.
struct mt76_vif_link already contains an rcu_head field that is unused at
this free site -- a developer oversight, since the adjacent
kfree_rcu_mightsleep call for rx_sc in the same function shows the
pattern was understood.
Replace kfree(mlink) with kfree_rcu(mlink, rcu_head).
Fixes: a8f424c128 ("wifi: mt76: add multi-radio remain_on_channel functions")
Signed-off-by: Rajat Gupta <rajat.gupta@oss.qualcomm.com>
Link: https://patch.msgid.link/20260507043531.492-1-rajat.gupta@oss.qualcomm.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On a STATION vif, removing a TDLS peer takes the mt7925_mac_sta_remove
-> mt7925_mac_sta_remove_links path. The first loop in that function
calls mt7925_mcu_add_bss_info(..., enable=false) for every link of the
station being removed. For a non-MLO STATION vif there is exactly one
link, link 0, whose bss_conf is the AP's. TDLS peers do not have their
own bss_conf - they share the AP's BSS.
The result is that every TDLS peer teardown sends a BSS_INFO_UPDATE
with enable=0 for the AP's BSS to the firmware, which wipes the AP-side
rate-control context. The connection stays associated and TX from the
host still works at the negotiated rate, but the AP's downlink to us
collapses to the lowest mandatory OFDM rate (HE-MCS 0 / 6 Mbit/s OFDM)
and only slowly recovers as rate adaptation re-learns under sustained
traffic. With brief or bursty traffic the link can stay at 6-72 Mbit/s
indefinitely, requiring a manual reconnect.
mt7925_mac_link_sta_remove() already guards its own
mt7925_mcu_add_bss_info(..., false) call with
"vif->type == NL80211_IFTYPE_STATION && !link_sta->sta->tdls".
Add the equivalent guard at the top of the cleanup loop in
mt7925_mac_sta_remove_links(), above the link_sta / link_conf /
mlink / mconf lookups, so TDLS peer teardown skips the loop body
entirely without doing the per-link work that would just be thrown
away.
Verified on mt7925e by triggering Samsung-S938B auto-TDLS via iperf3
and watching iw rx bitrate after teardown:
Before: rx bitrate collapses to 6.0-72.0 Mbit/s, oscillates 17/72/
137/288/432 Mbit/s for 30+ seconds, no full recovery without
a manual reassoc.
After: rx bitrate stays at 1200.9 Mbit/s HE-MCS 11 NSS 2 80 MHz
across the entire TDLS lifecycle.
bpftrace confirms a single mt7925_mcu_add_bss_info(enable=0) call per
teardown before the fix; zero such calls after.
Fixes: 3878b43336 ("wifi: mt76: mt7925: update mt7925_mac_link_sta_[add, assoc, remove] for MLO")
Cc: stable@vger.kernel.org
Signed-off-by: ElXreno <elxreno@gmail.com>
Assisted-by: Claude:claude-opus-4-7 bpftrace
Link: https://patch.msgid.link/20260506-mt7925-tdls-fixes-v2-2-46aa826ba8bb@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With HW TX encap offload enabled, the mt76 firmware builds the 802.11
header for the 802.3 frame using the per-WCID context. For a STATION
vif the HDR_TRANS TLV currently sets ToDS=1, which makes the firmware
default to the BSSID as A1 and emit STA->AP-formatted frames
regardless of which peer the WCID points to.
For TDLS-paired peers this is wrong. Data frames go on air addressed
to the AP, the AP MAC-ACKs and silently drops them per IEEE 802.11z
(an AP must not forward to a TDLS-paired peer). Management and
control frames bypass the HW encap path and still reach the peer;
only user data fails.
Add MT_WCID_FLAG_TDLS_PEER, set it in mt7915, mt7921, mt7925 and
mt7996 sta-add paths when sta->tdls is true, and override the
HDR_TRANS TLV in mt76_connac_mcu_wtbl_hdr_trans_tlv() (Connac2 -
mt7915 / mt7921 / mt7922), mt7925_mcu_sta_hdr_trans_tlv() (mt7925)
and mt7996_mcu_sta_hdr_trans_tlv() (mt7996) to set ToDS=0, FromDS=0
when the flag is set. The 3-addr non-DS form matches what 802.11z
uses for direct links; the firmware then constructs the frame with
A1=peer rather than A1=BSSID. HW encap offload remains enabled for
AP and any non-TDLS traffic.
Verified on mt7925e + Samsung S938B over a 5 GHz HE 80 MHz channel
with iperf3 -t 30 to the TDLS peer:
before fix: over the TDLS direct link, 7 TDLS Setup action
frames and 3 RTS frames reach the peer; 0 QoS
Data frames make it through (mgmt/control paths
bypass HW encap, the data path does not). iperf3
stalls.
after fix: 2.90 GBytes transferred at 830 Mbit/s sustained,
0 TCP retransmits.
mt7915, mt7921, mt7922 and mt7996 are not regression-tested in this
change for lack of hardware. Their HDR_TRANS handling mirrors the
verified mt7925 change; the firmware behavior is shared across these
chips.
Signed-off-by: ElXreno <elxreno@gmail.com>
Assisted-by: Claude:claude-opus-4-7 bpftrace tcpdump
Link: https://patch.msgid.link/20260506-mt7925-tdls-fixes-v2-1-46aa826ba8bb@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch is based on a BUG as reported by Bongani Hlope at
https://lore.kernel.org/all/20260502125824.425d7159@bongani-mini.home.org.za/
When a channel-switch announcement (CSA) beacon is received,
cfg80211 queues a wiphy work item that eventually calls
mt7921_channel_switch_rx_beacon(). If the station disconnects
(or the channel context is otherwise torn down) between the
time the work is queued and the time it runs, the driver's
dev->new_ctx pointer can already have been cleared to NULL.
mt7921_channel_switch_rx_beacon() then dereferences new_ctx
unconditionally, triggering a NULL pointer dereference at
address 0x0:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:mt7921_channel_switch_rx_beacon+0x1f/0x100 [mt7921_common]
The same missing guard exists in mt7925_channel_switch_rx_beacon(),
which shares the same code pattern introduced by the same commit.
Add an early-return NULL check for dev->new_ctx in both
mt7921_channel_switch_rx_beacon() and
mt7925_channel_switch_rx_beacon(). When new_ctx is NULL there is
no pending channel switch to process, so returning immediately is
the correct and safe action.
Fixes: 8aa2f59260 ("wifi: mt76: mt7921: introduce CSA support")
Reported-by: Bongani Hlope <developer@hlope.org.za>
Oops-Analysis: http://oops.fenrus.org/reports/lkml/20260502125824.425d7159@bongani-mini.home.org.za/report.html
Link: https://lore.kernel.org/all/20260502125824.425d7159@bongani-mini.home.org.za/
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Link: https://patch.msgid.link/20260504145107.1329197-1-arjan@linux.intel.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check return value instead of is_valid_ether_addr. The latter is handled
by the former.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260427051746.954704-1-rosenp@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7925_pci_probe() initializes DMA before registering the device. If
mt7925_register_device() fails, probe returns through err_free_irq without
tearing down DMA state.
That leaves the TX NAPI instance enabled and skips the DMA queue cleanup
that the normal remove path performs through mt7925e_unregister_device().
Add a dedicated unwind label for failures after mt7925_dma_init() succeeds.
Fixes: c948b5da6b ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Link: https://patch.msgid.link/20260426143728.41534-1-pakmyeonghun@bagmyeonghun-ui-MacBookPro.local
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit 2ccccf5fb4 ("net_sched: update hierarchical backlog too") renamed
qdisc_tree_decrease_qlen() to qdisc_tree_reduce_backlog(), but this comment
was missed. Update it.
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20260605212239.2261320-1-victor@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
With tab=8 (Linux Kernel coding style), there are a couple of lines
misaligned in the comment ASCII tables. Fix indentation for them.
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Link: https://patch.msgid.link/20260608082348.92575-1-shengchao.guo@oss.qualcomm.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The HP Omen 16-ap0xxx (board ID: 8E35) has the same WMI interface as
other Victus S boards, but requires quirks for correctly switching
thermal profile.
Add the DMI board name to victus_s_thermal_profile_boards[] table and
map it to omen_v1_legacy_thermal_params.
Testing on board 8E35 confirmed that platform profile is registered
successfully and fan RPMs are readable and controllable.
Tested-by: Ahmet Öztürk <sivasli-ahmet@gmx.de>
Reported-by: Ahmet Öztürk <sivasli-ahmet@gmx.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221523
Cc: stable@vger.kernel.org # v6.18+
Signed-off-by: Krishna Chomal <krishna.chomal108@gmail.com>
Link: https://patch.msgid.link/20260608134255.36280-1-krishna.chomal108@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
DRM atomic and modesetting aren't initialized if virtio-gpu driver built
with disabled KMS, leading to access of uninitialized data on driver
removal/unbinding and crashing kernel. Fix it by skipping shutting down
atomic core with unavailable KMS.
Fixes: 72122c69d7 ("drm/virtio: Add option to disable KMS support")
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Ryosuke Yasuoka <ryasuoka@redhat.com>
Reviewed-by: Ryosuke Yasuoka <ryasuoka@redhat.com>
Link: https://patch.msgid.link/20260604122743.13383-1-dmitry.osipenko@collabora.com
Fix modification of the received skbuff in rxrpc_input_soft_acks() and a
potential incorrect access of the buffer in a fragmented UDP packet (the
packet would probably have to be deliberately pre-generated as fragmented)
when AF_RXRPC tries to extract the contents of the SACK table by copying
out the contents of the SACK table into a buffer before attempting to parse
AF_RXRPC assumes that it can just call skb_condense() and then validly
access the SACK table from skb->data and that it will be a flat buffer -
but skb_condense() can silently fail to do anything under some
circumstances.
Note that whilst rxrpc_input_soft_acks() should be able to parse extended
ACKs, the rest of AF_RXRPC doesn't currently support that.
Further, there's then no need to call skb_condense() in rxrpc_input_ack(),
so don't.
Fixes: d57a3a1516 ("rxrpc: Save last ACK's SACK table rather than marking txbufs")
Reported-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://lore.kernel.org/r/20260513180907.2061972-1-michael.bommarito@gmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Jeffrey Altman <jaltman@auristor.com>
cc: Eric Dumazet <edumazet@google.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: stable@kernel.org
Link: https://patch.msgid.link/105362.1780573560@warthog.procyon.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that the system and CMA heaps can be built as modules, enable both
as modules in the arm multi_v7_defconfig.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20260527084135.842736-1-mripard@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove redundant, duplicated CONFIG_EXT4_FS to fix warnings like:
axm55xx_defconfig:198:warning: override: reassigning to symbol EXT4_FS
Fixes: c065b6046b ("Use CONFIG_EXT4_FS instead of CONFIG_EXT3_FS in all of the defconfigs")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Richard Cheng <icheng@nvidia.com>
Link: https://lore.kernel.org/r/20260603072726.19404-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If usb_reset_device() returns a negative error code, stop the
process of probing.
Fixes: 10c3271712 ("r8152: disable the ECM mode")
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260604092247.27158-450-nic_swsd@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
btf_parse_struct_metas() walks user-supplied BTF during BPF_BTF_LOAD,
and btf_repeat_fields() expands repeatable fields from array elements
into the fixed BTF_FIELDS_MAX scratch array used by btf_parse_fields().
The remaining-capacity check performs the expanded field count calculation
in u32. A malformed BTF can wrap that calculation, causing the check to
pass even when the expanded field count exceeds the scratch array
capacity. The following memcpy() can then write past the end of the
array.
Use checked addition and multiplication before copying repeated fields
and reject impossible counts.
Fixes: 797d73ee23 ("bpf: Check the remaining info_cnt before repeating btf fields")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moses <p@1g4.org>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20260605234301.1109063-1-p@1g4.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Replace the open-coded "p->on_rq == TASK_ON_RQ_MIGRATING" comparisons
in enqueue_task_dl() and dequeue_task_dl() with the existing
task_on_rq_migrating() helper, consistent with the rest of the
scheduler code.
No functional change.
Signed-off-by: Liang Luo <luoliang@kylinos.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://patch.msgid.link/20260608075500.387271-1-luoliang@kylinos.cn
The kernel coding style recommends using 'else if' instead of
placing 'if' on a separate line after 'else'. This change makes
the code consistent with the rest of the kernel codebase.
Signed-off-by: Liang Luo <luoliang@kylinos.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20260608071842.325159-1-luoliang@kylinos.cn
If we take runnable_avg in max(runnable_avg, util_avg) in cpu_util(), we
should then add or subtract task runnable_avg, but the arithmetic below
is still with task util_avg. This mixes runnable_avg with util_avg which
is incorrect.
Fix by always doing arithmetic with runnable_avg and only take
max(runnable_avg, util_avg) at the last step.
Fixes: 7d0583cf9e ("sched/fair, cpufreq: Introduce 'runnable boosting'")
Signed-off-by: Hongyan Xia <hongyan.xia@transsion.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://patch.msgid.link/20260605094318.37931-1-hongyan.xia@transsion.com
When building the kernel using the llvm-22.1.0-rust-1.93.1-x86_64
toolchain provided by kernel.org with ARCH=x86_64, the following symbols
are generated:
$ nm vmlinux | grep ' _R'.*Completion | rustfilt
ffffffff81827930 T <kernel::sync::completion::Completion>::complete_all
ffffffff81827950 T <kernel::sync::completion::Completion>::wait_for_completion
These Rust methods are thin wrappers around the C completion helpers
`complete_all` and `wait_for_completion`. Mark them `#[inline]` to keep
the wrapper pattern consistent with other small Rust helper methods.
After applying this patch, the above command will produce no output.
Suggested-by: Alice Ryhl <aliceryhl@google.com>
Signed-off-by: Fabricio Parra <a@alice0.com>
Signed-off-by: Boqun Feng <boqun@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Gary Guo <gary@garyguo.net>
Link: https://github.com/Rust-for-Linux/linux/issues/1145
Link: https://patch.msgid.link/20260316151056.287-1-a@alice0.com
Link: https://patch.msgid.link/20260605052331.1628-4-boqun@kernel.org
We have two pull requests on Rust synchronization primitives with 10+
patches in a row for recent cycles, so it makes sense to start the
effort of handling this area as a group.
Luckily for me, Gary Guo and Alice Ryhl agreed to help as
co-maintainers, and we also have a talented group of reviewers:
Lyude Paul started the SpinLockIrq work [1] and did an amazing job at
improving the design and implementation.
Daniel Almeida resolved the Lock<T: !Unpin> issue [2] and he did a fair
amount of reviews in areas related to synchronization primitives
already.
Onur Özkan started the ww_mutex work [3] and did an amazing job at
consolidating various design requirements and decisions.
Of course, this only reflects my own knowledge, and I believe they did
way more outside what I'm aware of ;-)
Note that having this MAINTAINERS entry is meant to bring more people
to help on the synchronization primitives in Rust, which means for patch
submissions and design discussion, please still involve the
corresponding maintainers (e.g. LOCKING and ATOMIC),
scripts/get_maintainers.pl should have this covered.
Signed-off-by: Boqun Feng <boqun@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Daniel Almeida <daniel.almeida@collabora.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Onur Özkan <work@onurozkan.dev>
Acked-by: Gary Guo <gary@garyguo.net>
Acked-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/rust-for-linux/20260302232154.861916-1-lyude@redhat.com/ [1]
Link: https://lore.kernel.org/all/20250828-lock-t-when-t-is-pinned-v2-0-b067c4b93fd6@collabora.com/ [2]
Link: https://lore.kernel.org/rust-for-linux/20260103073554.34855-1-work@onurozkan.dev/ [3]
Link: https://patch.msgid.link/20260415232830.8128-1-boqun@kernel.org
Link: https://patch.msgid.link/20260605052331.1628-2-boqun@kernel.org
The LPI2C driver requests DMA channels using dma_request_chan(), but
never releases them in lpi2c_imx_remove(), resulting in DMA channel
leaks every time the driver is unloaded.
Additionally, when lpi2c_dma_init() successfully requests the TX DMA
channel but fails to request the RX DMA channel, the probe falls back
to PIO mode and completes successfully. Since probe succeeds, the devres
framework will not trigger any cleanup, leaving the TX DMA channel and
the memory allocated for the dma structure held for the lifetime of the
device even though DMA is never used.
Switch to devm_dma_request_chan() to let the device core manage DMA
channel lifetime automatically. Wrap all allocations within a devres
group so that devres_release_group() can release all partially acquired
resources when DMA init fails and probe continues in PIO mode.
Fixes: a09c8b3f90 ("i2c: imx-lpi2c: add eDMA mode support for LPI2C")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Cc: <stable@vger.kernel.org> # v6.14+
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260520093323.2882070-1-carlos.song@oss.nxp.com
A crafted NTFS3 disk image triggers an in-kernel infinite loop at
mount time, hanging the mounting thread and firing the soft-lockup
watchdog within ~22s on multi-CPU hosts (panic with
kernel.softlockup_panic=1). The bug is reachable from desktop USB
auto-mount on distributions where udisks2 routes the NTFS signature
to the in-tree ntfs3 driver (Arch family and an increasing fraction
of Fedora / openSUSE / RHEL deployments); CAP_SYS_ADMIN-class manual
mount elsewhere.
check_rstbl()'s second walker iterates the free-entry singly-linked
list headed by rt->first_free with no upper bound on iteration count:
for (off = ff; off;) {
if (off == RESTART_ENTRY_ALLOCATED)
return false;
off = le32_to_cpu(*(__le32 *)Add2Ptr(rt, off));
if (off > ts - sizeof(__le32))
return false;
}
The existing guards cover three exits: end-of-list (off == 0), the
in-use marker (off == RESTART_ENTRY_ALLOCATED), and out-of-bounds
(off > ts - sizeof(__le32)). None of the three prevents an
in-bounds cycle.
A crafted on-disk RESTART_TABLE whose free chain contains a
self-loop or A->B->A cycle whose offsets satisfy:
- in range [sizeof(struct RESTART_TABLE), ts - sizeof(__le32)]
- (off - sizeof(struct RESTART_TABLE)) % rsize == 0
passes all existing guards and spins the mount-time thread forever.
Reproduced in UML by hand-forging a 2 MB NTFS3 image whose journal
RESTART_TABLE first_free = 0x18 and whose entry at offset 0x18
stores 0x18 as its next pointer; mount of the forged image with
the in-tree ntfs3 driver never returns.
Bound the walker by rt->used. Each entry on a legitimate free
chain is unique, and the total slot count is ne = le16_to_cpu
(rt->used). A traversal that visits more than ne slots is by
construction malformed; reject it as a corrupt RESTART_TABLE.
After this patch, mount of the forged image returns with -EINVAL
and a log_replay failure message, and mkntfs-produced legitimate
images mount cleanly (verified in the same UML harness).
Fixes: b46acd6a6a ("fs/ntfs3: Add NTFS journal")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
In do_action()'s UpdateRecordDataRoot (fslog.c:3489) and
UpdateRecordDataAllocation (fslog.c:3697) cases, the memmove
destination is `Add2Ptr(e, le16_to_cpu(e->view.data_off))`,
where e->view.data_off comes from an on-disk NTFS_DE inside
an INDEX_ROOT or INDEX_BUFFER. Neither case validates
view.data_off + dlen against e->size; the existing
check_if_index_root / check_if_alloc_index helpers walk the
entry chain and validate the entry's offset, but not its
internal view fields.
The neighbouring read sites (e.g., fs/ntfs3/index.c when
iterating view entries) check view.data_off + view.data_size
<= e->size. Apply the same bound at the two memmove sites.
Reproduced under UML+KASAN on mainline 8d90b09e6741 via
pr_warn-only probe instrumentation: with view.data_off forced
to 0xFFFC, the memmove writes 32 bytes past the end of the
NTFS_DE.
This is similar in shape to Pavitra Jha's 2026-05-02 patch
"fs/ntfs3: prevent oob in case UpdateRecordDataRoot"
(<20260502105008.21827-1-jhapavitra98@gmail.com>) which
proposes calling ntfs3_bad_de_range(); that helper does not
exist in mainline. This patch uses inline checks.
Fixes: b46acd6a6a ("fs/ntfs3: Add NTFS journal")
Cc: stable@vger.kernel.org
Reported-by: Pavitra Jha <jhapavitra98@gmail.com>
Closes: https://lore.kernel.org/ntfs3/20260502105008.21827-1-jhapavitra98@gmail.com/
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Add the firmware string '1583EMS1.109' to the ALLOWED_FW_10 array.
This enables Embedded Controller support, including battery charge
thresholds, for the MSI Pulse GL66 12UEK (MS-1583) laptop.
Signed-off-by: Luis de Carlos <reskoldo73@gmail.com>
Link: https://patch.msgid.link/20260527134750.25263-1-reskoldo73@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The Inspiron N5110 needs the touchpad LED quirk (Vostro V130 quirk)
to properly control the touchpad LED. Add its DMI identifier
to the existing quirk table, next to the similar Inspiron M5110 entry.
Tested on Dell Inspiron N5110.
The touchpad LED works correctly with this quirk enabled.
Signed-off-by: Gleb Sonichev <sonichev555@gmail.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://patch.msgid.link/20260525100047.20046-1-sonichev555@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The HP Omen 16-ap0xxx (board ID: 8D26) has the same WMI interface as
other Victus S boards, but requires quirks for correctly switching
thermal profile.
Add the DMI board name to victus_s_thermal_profile_boards[] table and
map it to omen_v1_legacy_thermal_params.
Testing on board 8D26 confirmed that platform profile is registered
successfully and fan RPMs are readable and controllable.
Tested-by: Alberto Escaño <alberto_e_88@yahoo.es>
Reported-by: Alberto Escaño <alberto_e_88@yahoo.es>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221514
Cc: stable@vger.kernel.org # v6.18+
Signed-off-by: Krishna Chomal <krishna.chomal108@gmail.com>
Link: https://patch.msgid.link/20260525102226.56300-1-krishna.chomal108@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
convert_ltr_scale() emits an unconditional pr_warn() whenever an LTR row
encoded by hardware has a scale-factor field of 6 or 7 (reserved values
per the PCIe LTR ECN). The function is called twice per LTR row (snoop
+ non-snoop) by pmc_core_ltr_show(), which is invoked on every read of
/sys/kernel/debug/pmc_core/ltr_show as well as during certain platform
driver activity.
On a Meteor Lake laptop with an Intel AX210 Wi-Fi card, this produces
4-12 "Invalid LTR scale factor." lines per second in dmesg, with no
context to help identify which PMC IP / row carries the bad value.
Switch to pr_warn_once() so the warning still flags the spec violation
once per boot, and include the offending scale value in the message.
Identifying the originating LTR row would require restructuring the
caller's loop to perform the validity check itself; that is left as a
separate change.
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Mike Bommarito <michael.bommarito@gmail.com>
Link: https://patch.msgid.link/20260523114517.101305-1-michael.bommarito@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
