pci_restore_rebar_state() uses the Resizable BAR Control register to decide
how many BARs to restore (nbars) and which BAR each iteration addresses
(bar_idx).
When a device does not respond, config reads typically return
PCI_ERROR_RESPONSE (~0). Both fields are 3 bits wide, so nbars and bar_idx
both evaluate to 7, past the spec's valid ranges for both fields.
pci_resource_n() then returns an unrelated resource slot, whose size is
used to derive a nonsensical value written back to the Resizable BAR
Control register.
Bail out if any Resizable BAR Control read returns PCI_ERROR_RESPONSE. No
further BARs are touched, which is safe because a config read that returns
PCI_ERROR_RESPONSE indicates the device is unreachable and restoration is
pointless.
Fixes: d3252ace0b ("PCI: Restore resized BAR state on resume")
Signed-off-by: Marco Nenciarini <mnencia@kcore.it>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/666cac19b5daa0ab0e0ab64454e76b4d24465dbd.1776429882.git.mnencia@kcore.it
When a PCI device is unbound from its driver, pci_device_remove() sets the
cached power state in pci_dev->current_state to PCI_UNKNOWN. This was
introduced by commit 2449e06a56 ("PCI: reset pci device state to unknown
state for resume") to invalidate the cached power state in case the system
is subsequently put to sleep.
For bound devices, the cached power state is set to PCI_UNKNOWN in
pci_pm_suspend_noirq(), immediately before entering system sleep.
Extend to unbound devices for consistency.
This obviates the need to change the cached power state on unbind, so stop
doing so.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/af7d11d3ceb231acc90829f7a5c8400c2446744f.1776415510.git.lukas@wunner.de
When ntfs_attr_get_search_ctx() fails and returns NULL, the function
returned early without calling put_page(ipage).
Fix this by jumping to err_out label on error. The err_out path now
properly releases the page and the mutex, with a NULL check for
the search context.
Reported-by: DaeMyung Kang <charsyam@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Without poweroff node Exynos850-based board continue to draw current
(around ~60 mA with my test setup) after poweroff. Kernel also reports
different lockup problems and RCU stalls warnings continuosly after
last kernel messages about hardware being switched off.
Turns out we missed a write to PMU's PS_HOLD_CONTROL (PMU + 0x30c)
register that actually switches the SoC off.
Add poweroff node that implements this.
With this change the current draw after power off is in range of few
milliampers and lockup messages are no more.
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20260325-exynos850-poweroff-v1-1-34c19c06e74d@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In ntfs_mapping_pairs_decompress(), lowest_vcn is read from
on-disk metadata and used as the initial vcn without validation.
A malformed value can introduce an invalid (e.g. negative) vcn,
corrupting the runlist from the start.
Additionally, the accumulation
vcn += deltaxcn
does not check for s64 overflow. A crafted mapping pairs array
can wrap vcn to a negative value, breaking the monotonically-
increasing invariant relied upon by ntfs_rl_vcn_to_lcn() and
related helpers.
Fix this by validating lowest_vcn and using check_add_overflow()
for vcn accumulation.
Signed-off-by: Zhan Xusheng <zhanxusheng@xiaomi.com>
Reviewed-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
ntfs_reparse_set_wsl_symlink() converts the symlink target into an
allocated NLS string and transfers ownership to ni->target only after
ntfs_set_ntfs_reparse_data() succeeds. If setting the reparse data fails,
the converted target is left unreferenced and leaks.
Free the converted target on the reparse update failure path. Use kfree()
for the other local failure path as well, matching the ntfs_ucstonls()
allocation contract.
Fixes: fc053f05ca ("ntfs: add reparse and ea operations")
Signed-off-by: DaeMyung Kang <charsyam@gmail.com>
Reviewed-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
ntfs_index_walk_down() allocates ictx->ib when descending from the root
into an index allocation block. If that allocation fails, the old code
still passes the NULL buffer to ntfs_ib_read(), which can write through
it via ntfs_inode_attr_pread().
Allocate the index block into a temporary pointer and return -ENOMEM
before changing the index context on allocation failure. Also propagate
ERR_PTR() through ntfs_index_next() and ntfs_readdir() so walk-down
allocation or index block read failures are not mistaken for normal
index iteration inside the filesystem.
ntfs_readdir() keeps the existing userspace-visible behavior of
suppressing readdir errors after marking end_in_iterate; this change only
prevents the walk-down failure path from dereferencing NULL internally.
The failure was reproduced with failslab fail-nth injection on getdents64;
the original module hits a NULL pointer dereference in memcpy_orig through
ntfs_ib_read(), while the patched module reaches the same
ntfs_index_walk_down() allocation failure without crashing.
Fixes: 0a8ac0c1fa ("ntfs: update directory operations")
Signed-off-by: DaeMyung Kang <charsyam@gmail.com>
Reviewed-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Param used for setting FW trace mask at module load time. Other debugfs
entry exist to allow update at run time.
Signed-off-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Reviewed-by: Alessio Belle <alessio.belle@imgtec.com>
Link: https://patch.msgid.link/20260427-ftrace_fix-v3-2-e081530759a8@imgtec.com
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Modernize string-to-number conversion in mtdsuper.c by replacing
simple_strtoul with kstrtouint. This change provides proper type safety
for MTD device numbers which are non-negative integers.
Using kstrtouint avoids unsigned long to int conversion and is more
appropriate for device indices. The debug output format specifier is
updated to %u for unsigned int.
Signed-off-by: Haoyu Lu <hechushiguitu666@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace deprecated simple_strtoul with kstrtouint for better error
handling and type safety. The kstrtouint function provides stricter
validation, automatically rejecting inputs like "123abc" that
simple_strtoul would partially accept.
Using kstrtouint avoids unsigned long to int conversion and is more
appropriate for MTD device indices which are non-negative integers.
Signed-off-by: Haoyu Lu <hechushiguitu666@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Various names for Qualcomm as a company are used in user-visible config
options: QCOM, Qualcomm and Qualcomm Technologies. Switch to unified
"Qualcomm" so it will be easier for users to identify the options when
for example running menuconfig.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In most scenarios this variant is actually unused (VCR is written in
SSDR mode), but we need to provide an octal variant. The address is 24
bits but is sent over 4 bytes MSB first. This means we need to shift the
register address by one extra byte for the address to be correct.
I didn't catch this initially because the volatile register region is
256 bytes wide, so the write-then-read procedure did work with the small
register addresses I was using at that time: 0 and 1.
Fixes: 44a2f49b9b ("mtd: spinand: winbond: W35N octal DTR support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Both W35N02JW and W35N04JW diverge from W35N01JW when it comes to the
"data read" operation in ODTR mode. In order to stuff more address
bits (up to 18), the second command byte is replaced by the most
significant address bits, keeping the number of address bytes to 2.
Fixes: 44a2f49b9b ("mtd: spinand: winbond: W35N octal DTR support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some devices stuff address bits in the double byte opcode (in place of
the repeated byte) in order to be able to increase the size of the
devices, without adding extra address bytes.
Create a flag to identify those devices. When the flag is set, use the
"packed" variant for the read data operation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sashiko noticed an out-of-bounds read [1].
In spi_nor_params_show(), the snor_f_names array is passed to
spi_nor_print_flags() using sizeof(snor_f_names).
Since snor_f_names is an array of pointers, sizeof() returns the total
number of bytes occupied by the pointers
(element_count * sizeof(void *))
rather than the element count itself. On 64-bit systems, this makes the
passed length 8x larger than intended.
Inside spi_nor_print_flags(), the 'names_len' argument is used to
bounds-check the 'names' array access. An out-of-bounds read occurs
if a flag bit is set that exceeds the array's actual element count
but is within the inflated byte-size count.
Correct this by using ARRAY_SIZE() to pass the actual number of
string pointers in the array.
Cc: stable@vger.kernel.org
Fixes: 0257be79fc ("mtd: spi-nor: expose internal parameters via debugfs")
Closes: https://sashiko.dev/#/patchset/20260417-die-erase-fix-v2-1-73bb7004ebad%40infineon.com [1]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Takahiro Kuwano <takahiro.kuwano@infineon.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mfill_copy_folio_retry() drops mmap_lock for the copy_from_user() call.
During this window, the VMA can be replaced with a different type (e.g.
hugetlb), making the caller's ops pointer stale. Subsequent use of the
stale ops would dispatch into the wrong per-vma handlers.
Capture the VMA's ops via vma_uffd_ops() before dropping the lock and
compare against the current vma_uffd_ops() after re-acquiring it.
Return -EAGAIN if they differ so the operation can be retried. This
avoids comparing against the caller's ops which may have been
overridden to anon_uffd_ops for MAP_PRIVATE file-backed mappings.
Link: https://lore.kernel.org/20260424183638.196227-1-devnexen@gmail.com
Fixes: 6ab703034f ("userfaultfd: mfill_atomic(): remove retry logic")
Reported-by: Usama Arif <usama.arif@linux.dev>
Closes: https://lore.kernel.org/all/20260410114809.3592720-1-usama.arif@linux.dev/
Signed-off-by: David Carlier <devnexen@gmail.com>
Acked-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Cc: Jann Horn <jannh@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <ljs@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
DAMON_STAT updates 'enabled' parameter value, which represents the running
status of its kdamond, when the user explicitly requests start/stop of the
kdamond. The kdamond can, however, be stopped even if the user explicitly
requested the stop, if ctx->regions_score_histogram allocation failure at
beginning of the execution of the kdamond. Hence, if the kdamond is
stopped by the allocation failure, the value of the parameter can be
stale.
Users could show the stale value and be confused. The problem will only
rarely happen in real and common setups because the allocation is arguably
too small to fail. Also, unlike the similar bugs that are now fixed in
DAMON_RECLAIM and DAMON_LRU_SORT, kdamond can be restarted in this case,
because DAMON_STAT force-updates the enabled parameter value for user
inputs. The bug is a bug, though.
The issue stems from the fact that there are multiple events that can
change the status, and following all the events is challenging.
Dynamically detect and use the fresh status for the parameters when those
are requested.
The issue was dicovered [1] by Sashiko.
Link: https://lore.kernel.org/20260419161003.79176-4-sj@kernel.org
Link: https://lore.kernel.org/20260416040602.88665-1-sj@kernel.org [1]
Fixes: 369c415e60 ("mm/damon: introduce DAMON_STAT module")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: Liew Rui Yan <aethernet65535@gmail.com>
Cc: <stable@vger.kernel.org> # 6.17.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
DAMON_LRU_SORT updates 'enabled' and 'kdamond_pid' parameter values, which
represents the running status of its kdamond, when the user explicitly
requests start/stop of the kdamond. The kdamond can, however, be stopped
in events other than the explicit user request in the following three
events.
1. ctx->regions_score_histogram allocation failure at beginning of the
execution,
2. damon_commit_ctx() failure due to invalid user input, and
3. damon_commit_ctx() failure due to its internal allocation failures.
Hence, if the kdamond is stopped by the above three events, the values of
the status parameters can be stale. Users could show the stale values and
be confused. This is already bad, but the real consequence is worse.
DAMON_LRU_SORT avoids unnecessary damon_start() and damon_stop() calls
based on the 'enabled' parameter value. And the update of 'enabled'
parameter value depends on the damon_start() and damon_stop() call
results. Hence, once the kdamond has stopped by the unintentional events,
the user cannot restart the kdamond before the system reboot. For
example, the issue can be reproduced via below steps.
# cd /sys/module/damon_lru_sort/parameters
#
# # start DAMON_LRU_SORT
# echo Y > enabled
# ps -ef | grep kdamond
root 806 2 0 17:53 ? 00:00:00 [kdamond.0]
root 808 803 0 17:53 pts/4 00:00:00 grep kdamond
#
# # commit wrong input to stop kdamond withou explicit stop request
# echo 3 > addr_unit
# echo Y > commit_inputs
bash: echo: write error: Invalid argument
#
# # confirm kdamond is stopped
# ps -ef | grep kdamond
root 811 803 0 17:53 pts/4 00:00:00 grep kdamond
#
# # users casn now show stable status
# cat enabled
Y
# cat kdamond_pid
806
#
# # even after fixing the wrong parameter,
# # kdamond cannot be restarted.
# echo 1 > addr_unit
# echo Y > enabled
# ps -ef | grep kdamond
root 815 803 0 17:54 pts/4 00:00:00 grep kdamond
The problem will only rarely happen in real and common setups for the
following reasons. The allocation failures are unlikely in such setups
since those allocations are arguably too small to fail. Also sane users
on real production environments may not commit wrong input parameters.
But once it happens, the consequence is quite bad. And the bug is a bug.
The issue stems from the fact that there are multiple events that can
change the status, and following all the events is challenging.
Dynamically detect and use the fresh status for the parameters when those
are requested.
Link: https://lore.kernel.org/20260419161003.79176-3-sj@kernel.org
Fixes: 40e983cca9 ("mm/damon: introduce DAMON-based LRU-lists Sorting")
Co-developed-by: Liew Rui Yan <aethernet65535@gmail.com>
Signed-off-by: Liew Rui Yan <aethernet65535@gmail.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> # 6.0.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "mm/damon/modules: detect and use fresh status", v3.
DAMON modules including DAMON_RECLAIM, DAMON_LRU_SORT and DAMON_STAT
commonly expose the kdamond running status via their parameters. Under
certain scenarios including wrong user inputs and memory allocation
failures, those parameter values can be stale. It can confuse users. For
DAMON_RECLAIM and DAMON_LRU_SORT, it even makes the kdamond unable to be
restarted before the system reboot.
The problem comes from the fact that there are multiple events for the
status changes and it is difficult to follow up all the scenarios. Fix
the issue by detecting and using the status on demand, instead of using a
cached status that is difficult to be updated.
Patches 1-3 fix the bugs in DAMON_RECLAIM, DAMON_LRU_SORT and DAMON_STAT
in the order.
This patch (of 3):
DAMON_RECLAIM updates 'enabled' and 'kdamond_pid' parameter values, which
represents the running status of its kdamond, when the user explicitly
requests start/stop of the kdamond. The kdamond can, however, be stopped
in events other than the explicit user request in the following three
events.
1. ctx->regions_score_histogram allocation failure at beginning of the
execution,
2. damon_commit_ctx() failure due to invalid user input, and
3. damon_commit_ctx() failure due to its internal allocation failures.
Hence, if the kdamond is stopped by the above three events, the values of
the status parameters can be stale. Users could show the stale values and
be confused. This is already bad, but the real consequence is worse.
DAMON_RECLAIM avoids unnecessary damon_start() and damon_stop() calls
based on the 'enabled' parameter value. And the update of 'enabled'
parameter value depends on the damon_start() and damon_stop() call
results. Hence, once the kdamond has stopped by the unintentional events,
the user cannot restart the kdamond before the system reboot. For
example, the issue can be reproduced via below steps.
# cd /sys/module/damon_reclaim/parameters
#
# # start DAMON_RECLAIM
# echo Y > enabled
# ps -ef | grep kdamond
root 806 2 0 17:53 ? 00:00:00 [kdamond.0]
root 808 803 0 17:53 pts/4 00:00:00 grep kdamond
#
# # commit wrong input to stop kdamond withou explicit stop request
# echo 3 > addr_unit
# echo Y > commit_inputs
bash: echo: write error: Invalid argument
#
# # confirm kdamond is stopped
# ps -ef | grep kdamond
root 811 803 0 17:53 pts/4 00:00:00 grep kdamond
#
# # users casn now show stable status
# cat enabled
Y
# cat kdamond_pid
806
#
# # even after fixing the wrong parameter,
# # kdamond cannot be restarted.
# echo 1 > addr_unit
# echo Y > enabled
# ps -ef | grep kdamond
root 815 803 0 17:54 pts/4 00:00:00 grep kdamond
The problem will only rarely happen in real and common setups for the
following reasons. The allocation failures are unlikely in such setups
since those allocations are arguably too small to fail. Also sane users
on real production environments may not commit wrong input parameters.
But once it happens, the consequence is quite bad. And the bug is a bug.
The issue stems from the fact that there are multiple events that can
change the status, and following all the events is challenging.
Dynamically detect and use the fresh status for the parameters when those
are requested.
Link: https://lore.kernel.org/20260419161003.79176-1-sj@kernel.org
Link: https://lore.kernel.org/20260419161003.79176-2-sj@kernel.org
Fixes: e035c280f6 ("mm/damon/reclaim: support online inputs update")
Co-developed-by: Liew Rui Yan <aethernet65535@gmail.com>
Signed-off-by: Liew Rui Yan <aethernet65535@gmail.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> # 5.19.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Several of the mm selftests made use of /proc/pid/mem as part of their
operation but we do not specify this in the config fragment for them, at
least mkdirty and ksm_functional_tests have this requirement.
This has been working fine in practice since PROC_MEM_ALWAYS_FORCE was the
default setting but commit 599bbba5a3 ("proc: make PROC_MEM_FORCE_PTRACE
the Kconfig default") that is no longer the case, meaning that tests run
on kernels built based on defconfigs have started having the new more
restrictive default and failing. Add PROC_MEM_ALWAYS_FORCE to the config
fragment for the mm selftests.
Thanks to Aishwarya TCV for spotting the issue and identifying the commit
that introduced it.
Link: https://lore.kernel.org/20260416-selftests-mm-proc-mem-always-force-v1-1-3f5865153c67@kernel.org
Fixes: 599bbba5a3 ("proc: make PROC_MEM_FORCE_PTRACE the Kconfig default")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: Aishwarya TCV <aishwarya.tcv@arm.com>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: David Hildenbrand (Arm) <david@kernel.org>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Dev Jain <dev.jain@arm.com>
Cc: Lorenzo Stoakes <ljs@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
damon_sysfs_quot_goal->path can be read and written by users, via DAMON
sysfs 'path' file. It can also be indirectly read, for the parameters
{on,off}line committing to DAMON. The reads for parameters committing are
protected by damon_sysfs_lock to avoid the sysfs files being destroyed
while any of the parameters are being read. But the user-driven direct
reads and writes are not protected by any lock, while the write is
deallocating the path-pointing buffer. As a result, the readers could
read the already freed buffer (user-after-free). Note that the user-reads
don't race when the same open file is used by the writer, due to kernfs's
open file locking. Nonetheless, doing the reads and writes with separate
open files would be common. Fix it by protecting both the user-direct
reads and writes with damon_sysfs_lock.
Link: https://lore.kernel.org/20260423150253.111520-3-sj@kernel.org
Fixes: c41e253a41 ("mm/damon/sysfs-schemes: implement path file under quota goal directory")
Co-developed-by: Junxi Qian <qjx1298677004@gmail.com>
Signed-off-by: Junxi Qian <qjx1298677004@gmail.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> # 6.19.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "mm/damon/sysfs-schemes: fix use-after-free for [memcg_]path".
Reads of 'memcg_path' and 'path' files in DAMON sysfs interface could race
with their writes, results in use-after-free. Fix those.
This patch (of 2):
damon_sysfs_scheme_filter->mmecg_path can be read and written by users,
via DAMON sysfs memcg_path file. It can also be indirectly read, for the
parameters {on,off}line committing to DAMON. The reads for parameters
committing are protected by damon_sysfs_lock to avoid the sysfs files
being destroyed while any of the parameters are being read. But the
user-driven direct reads and writes are not protected by any lock, while
the write is deallocating the memcg_path-pointing buffer. As a result,
the readers could read the already freed buffer (user-after-free). Note
that the user-reads don't race when the same open file is used by the
writer, due to kernfs's open file locking. Nonetheless, doing the reads
and writes with separate open files would be common. Fix it by protecting
both the user-direct reads and writes with damon_sysfs_lock.
Link: https://lore.kernel.org/20260423150253.111520-1-sj@kernel.org
Link: https://lore.kernel.org/20260423150253.111520-2-sj@kernel.org
Fixes: 4f489fe6af ("mm/damon/sysfs-schemes: free old damon_sysfs_scheme_filter->memcg_path on write")
Co-developed-by: Junxi Qian <qjx1298677004@gmail.com>
Signed-off-by: Junxi Qian <qjx1298677004@gmail.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> # 6.16.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Update my email address as my work email account is no longer in use.
Also update .mailmap.
Link: https://lore.kernel.org/20260423132649.31126-1-li.wang@linux.dev
Signed-off-by: Li Wang <li.wang@linux.dev>
Reviewed-by: Cyril Hrubis <chrubis@suse.cz>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jakub Kacinski <kuba@kernel.org>
Cc: Li Wang <liwang@redhat.com>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Shannon Nelson <sln@onemain.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Switching to private email address. Update all contact information
Add an entry to mailmap at the same time.
Link: https://lore.kernel.org/20260422184310.2682901-1-liam@infradead.org
Signed-off-by: Liam R. Howlett <liam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When the user requests a total hugetlb CMA size without per-node
specification, hugetlb_cma_reserve() computes per_node from
hugetlb_cma_size and the number of nodes that have memory
per_node = DIV_ROUND_UP(hugetlb_cma_size,
nodes_weight(hugetlb_bootmem_nodes));
The reservation loop later computes
size = round_up(min(per_node, hugetlb_cma_size - reserved),
PAGE_SIZE << order);
So the actually reserved per_node size is multiple of (PAGE_SIZE <<
order), but the logged per_node is not rounded up, so it may be smaller
than the actual reserved size.
For example, as the existing comment describes, if a 3 GB area is
requested on a machine with 4 NUMA nodes that have memory, 1 GB is
allocated on the first three nodes, but the printed log is
hugetlb_cma: reserve 3072 MiB, up to 768 MiB per node
Round per_node up to (PAGE_SIZE << order) before logging so that the
printed log always matches the actual reserved size. No functional change
to the actual reservation size, as the following case analysis shows
1. remaining (hugetlb_cma_size - reserved) >= rounded per_node
- AS-IS: min() picks unrounded per_node;
round_up() returns rounded per_node
- TO-BE: min() picks rounded per_node;
round_up() returns rounded per_node (no-op)
2. remaining < unrounded per_node
- AS-IS: min() picks remaining;
round_up() returns round_up(remaining)
- TO-BE: min() picks remaining;
round_up() returns round_up(remaining)
3. unrounded per_node <= remaining < rounded per_node
- AS-IS: min() picks unrounded per_node;
round_up() returns rounded per_node
- TO-BE: min() picks remaining;
round_up() returns round_up(remaining) equals rounded per_node
Link: https://lore.kernel.org/20260422143353.852257-1-ekffu200098@gmail.com
Fixes: cf11e85fc0 ("mm: hugetlb: optionally allocate gigantic hugepages using cma") # 5.7
Signed-off-by: Sang-Heon Jeon <ekffu200098@gmail.com>
Reviewed-by: Muchun Song <muchun.song@linux.dev>
Cc: David Hildenbrand <david@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The pattern "include/linux/page[-_]*" matches every file that starts with
"page", because it's a regex and not a glob (so it has the meaning of
include/linux/page + match [-_] 0+ times).
Fix it up into a more regex-correct expression. Doing so reduces CC's
drastically in patches that touch pagemap.h (which is maintained as part
of PAGE CACHE).
As a side-effect, move linux/pageblock-flags.h explicitly under PAGE
ALLOCATOR.
Link: https://lore.kernel.org/linux-mm/20260422005608.342028-1-fmayle@google.com/
Link: https://lore.kernel.org/20260422123726.517220-1-pfalcato@suse.de
Signed-off-by: Pedro Falcato <pfalcato@suse.de>
Reviewed-by: Lorenzo Stoakes <ljs@kernel.org>
Acked-by: David Hildenbrand (Arm) <david@kernel.org>
Acked-by: Vlastimil Babka (SUSE) <vbabka@kernel.org>
Reviewed-by: SeongJae Park <sj@kernel.org>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The mmap_prepare hook functionality includes the ability to invoke
mmap_prepare() from the mmap() hook of existing 'stacked' drivers, that is
ones which are capable of calling the mmap hooks of other drivers/file
systems (e.g. overlayfs, shm).
As part of the mmap_prepare action functionality, we deal with errors by
unmapping the VMA should one arise. This works in the usual mmap_prepare
case, as we invoke this action at the last moment, when the VMA is
established in the maple tree.
However, the mmap() hook passes a not-fully-established VMA pointer to the
caller (which is the motivation behind the mmap_prepare() work), which is
detached.
So attempting to unmap a VMA in this state will be problematic, with the
most obvious symptom being a warning in vma_mark_detached(), because the
VMA is already detached.
It's also unncessary - the mmap() handler will clean up the VMA on error.
So to fix this issue, this patch propagates whether or not an mmap action
is being completed via the compatibility layer or directly.
If the former, then we do not attempt VMA cleanup, if the latter, then we
do.
This patch also updates the userland VMA tests to reflect the change.
Link: https://lore.kernel.org/20260421102150.189982-1-ljs@kernel.org
Fixes: ac0a3fc9c0 ("mm: add ability to take further action in vm_area_desc")
Signed-off-by: Lorenzo Stoakes <ljs@kernel.org>
Reported-by: syzbot+db390288d141a1dccf96@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/69e69734.050a0220.24bfd3.0027.GAE@google.com/
Cc: David Hildenbrand <david@kernel.org>
Cc: Jann Horn <jannh@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Pedro Falcato <pfalcato@suse.de>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The proactive nr_dirty > gdtc->bg_thresh check in balance_dirty_pages()
only checks the global dirty threshold to start background writeback while
the writer is still free-running, but for strictlimit BDIs (eg fuse), the
per-wb dirty count can exceed the per-wb background threshold while the
global threshold is not yet exceeded, so background writeback for this
case never gets proactively started.
Add a per-wb threshold check for strictlimit BDIs so that background
writeback is started when wb_dirty exceeds wb_bg_thresh, which drains
dirty pages before the writer hits the throttle wall, matching the
proactive behavior that the global check provides for non-strictlimit
BDIs.
fio runs on fuse show about a 3-4% improvement in perf for buffered
writes:
fio --name=writeback_test --ioengine=psync --rw=write --bs=128k \
--size=2G --numjobs=4 --ramp_time=10 --runtime=20 \
--time_based --group_reporting=1 --direct=0
Link: https://lore.kernel.org/20260326234629.840938-2-joannelkoong@gmail.com
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fix two error handling issues in kho_add_subtree(), where it doesn't
handle the error path correctly.
1. If fdt_setprop() fails after the subnode has been created, the
subnode is not removed. This leaves an incomplete node in the FDT
(missing "preserved-data" or "blob-size" properties).
2. The fdt_setprop() return value (an FDT error code) is stored
directly in err and returned to the caller, which expects -errno.
Fix both by storing fdt_setprop() results in fdt_err, jumping to a new
out_del_node label that removes the subnode on failure, and only setting
err = 0 on the success path, otherwise returning -ENOMEM (instead of
FDT_ERR_ errors that would come from fdt_setprop).
No user-visible changes. This patch fixes error handling in the KHO
(Kexec HandOver) subsystem, which is used to preserve data across kexec
reboots. The fix only affects a rare failure path during kexec
preparation — specifically when the kernel runs out of space in the
Flattened Device Tree buffer while registering preserved memory regions.
In the unlikely event that this error path was triggered, the old code
would leave a malformed node in the device tree and return an incorrect
error code to the calling subsystem, which could lead to confusing log
messages or incorrect recovery decisions. With this fix, the incomplete
node is properly cleaned up and the appropriate errno value is propagated,
this error code is not returned to the user.
Link: https://lore.kernel.org/20260410-kho_fix_send-v2-1-1b4debf7ee08@debian.org
Fixes: 3dc92c3114 ("kexec: add Kexec HandOver (KHO) generation helpers")
Signed-off-by: Breno Leitao <leitao@debian.org>
Suggested-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Cc: Alexander Graf <graf@amazon.com>
Cc: Breno Leitao <leitao@debian.org>
Cc: Pasha Tatashin <pasha.tatashin@soleen.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When session allocation fails during deserialization, the global 'err'
variable was not updated before returning. This caused subsequent calls
to luo_session_deserialize() to incorrectly report success.
Ensure 'err' is set to the error code from PTR_ERR(session). This ensures
that an error is correctly returned to userspace when it attempts to open
/dev/liveupdate in the new kernel if deserialization failed.
Link: https://lore.kernel.org/20260415193738.515491-1-pasha.tatashin@soleen.com
Signed-off-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Pratyush Yadav (Google) <pratyush@kernel.org>
Cc: David Matlack <dmatlack@google.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Samiullah Khawaja <skhawaja@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit 4c5d336588 ("mm/vmalloc: allow to set node and align in
vrealloc") added the ability to force a new allocation if the current
pointer is on the wrong NUMA node, or if an alignment constraint is not
met, even if the user is shrinking the allocation.
On this path (need_realloc), the code allocates a new object of 'size'
bytes and then memcpy()s 'old_size' bytes into it. If the request is to
shrink the object (size < old_size), this results in an out-of-bounds
write on the new buffer.
Fix this by bounding the copy length by the new allocation size.
Link: https://lore.kernel.org/20260420114805.3572606-2-elver@google.com
Fixes: 4c5d336588 ("mm/vmalloc: allow to set node and align in vrealloc")
Signed-off-by: Marco Elver <elver@google.com>
Reported-by: Harry Yoo (Oracle) <harry@kernel.org>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Acked-by: Vlastimil Babka (SUSE) <vbabka@kernel.org>
Reviewed-by: Harry Yoo (Oracle) <harry@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In scpsys_get_bus_protection_legacy(), of_find_node_with_property()
returns a device node with its reference count incremented. The function
then calls of_node_put(node) before checking whether
syscon_regmap_lookup_by_phandle() returns an error. If an error occurs,
dev_err_probe() dereferences the node pointer to print diagnostic
information, but the node memory may have already been freed due to the
earlier of_node_put(), leading to a use-after-free vulnerability.
Fix this by moving the of_node_put() call after the error check, ensuring
the node is still valid when accessed in the error path.
Fixes: c29345fa5f ("pmdomain: mediatek: Refactor bus protection regmaps retrieval")
Cc: stable@vger.kernel.org
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit cac173bea5 ("ACPI: processor: idle: Rework the handling of
acpi_processor_ffh_lpi_probe()") moved the acpi_processor_ffh_lpi_probe()
call from acpi_processor_setup_cpuidle_dev(), where its return value was
ignored, to acpi_processor_get_power_info(), where it is now treated as
a hard failure. As a result, platforms where psci_acpi_cpu_init_idle()
returned -ENODEV stopped registering any cpuidle states, forcing CPUs to
busy-poll when idle.
On NVIDIA Grace (aarch64) systems with PSCIv1.1, pr->power.count is 1
(only WFI, no deep PSCI states beyond it), so the previous
"count = pr->power.count - 1; if (count <= 0) return -ENODEV;" check
returned -ENODEV for all 72 CPUs and disabled cpuidle entirely.
The lpi_states count is already validated in acpi_processor_get_lpi_info(),
so the check here is redundant. Simplify the loop to iterate over
lpi_states[1..power.count). When only WFI is present, the loop body
simply does not execute and the function returns 0, which is the correct
outcome: there is nothing to validate for FFH and no error to report.
Suggested-by: Huisong Li <lihuisong@huawei.com>
Cc: stable@vger.kernel.org
Fixes: cac173bea5 ("ACPI: processor: idle: Rework the handling of acpi_processor_ffh_lpi_probe()")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Sudeep Holla <sudeep.holla@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
create_card() takes a reference on the USB device with usb_get_dev()
and stores the matching usb_put_dev() in card_free(), which is
installed as the snd_card's ->private_free destructor.
However, ->private_free is only assigned near the end of init_card(),
after several failure points (usb_set_interface(), EP type checks,
usb_submit_urb(), the EP1_CMD_GET_DEVICE_INFO exchange, and its
timeout). When any of those fail, init_card() returns an error to
snd_probe(), which calls snd_card_free(card). Because ->private_free
is still NULL, card_free() never runs, the usb_get_dev() reference
is not dropped, and the struct usb_device leaks along with its
descriptor allocations and device_private.
syzbot reproduces this with a malformed UAC3 device whose only valid
altsetting is 0; init_card()'s usb_set_interface(usb_dev, 0, 1) call
fails with -EIO and triggers the leak.
Move the ->private_free assignment into create_card(), immediately
after usb_get_dev(), so that every error path reaching snd_card_free()
balances the reference. card_free()'s callees (snd_usb_caiaq_input_free,
free_urbs, kfree) already tolerate the partially-initialized state
because the chip private area is zero-initialized by snd_card_new().
Fixes: 80bb50e2d4 ("ALSA: caiaq: take a reference on the USB device in create_card()")
Reported-by: syzbot+2afd7e71155c7e241560@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2afd7e71155c7e241560
Tested-by: syzbot+2afd7e71155c7e241560@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Deepanshu Kartikey <kartikey406@gmail.com>
Link: https://patch.msgid.link/20260426001934.70813-1-kartikey406@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a device is attached to a PM domain through genpd_dev_pm_attach_by_id(),
genpd calls pm_runtime_enable() for the corresponding virtual device that
it registers. While this avoids boilerplate code in drivers, there is no
corresponding call to pm_runtime_disable() in genpd_dev_pm_detach().
This means these virtual devices are typically detached from its genpd,
while runtime PM remains enabled for them, which is not how things are
designed to work. In worst cases it may lead to critical errors, like a
NULL pointer dereference bug in genpd_runtime_suspend(), which was recently
reported. For another case, we may end up keeping an unnecessary vote for a
performance state for the device.
To fix these problems, let's add this missing call to pm_runtime_disable()
in genpd_dev_pm_detach().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/CAMuHMdWapT40hV3c+CSBqFOW05aWcV1a6v_NiJYgoYi0i9_PDQ@mail.gmail.com/
Fixes: 3c095f32a9 ("PM / Domains: Add support for multi PM domains per device to genpd")
Cc: stable@vger.kernel.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Cortex-A9 PMU accesses the hardware via system coprocessor registers,
not memory-mapped I/O. The driver does not parse or use a 'reg' property
from the device tree, so we can remove the reg from the DTS.
This change fixes this dtbs_check warning:
(arm,cortex-a9-pmu): 'reg' does not match any of the regexes
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The Agilex7-M devkit contains an Agilex7M SoC, which is a newly branded
version of the original Agilex SoC. The Agilex7M core peripherals are
identical to the Agilex SoC.
We can re-use the socfpga_agilex.dtsi for this devkit. The Agilex7-M
devkit supports PCIE 5.0(x16), DDR4, DDR5, LPDDR5 and does not have QSPI.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add a missing sanity check for bNrChannels in detect_usb_format()
to prevent a division by zero in playback_urb_complete() and
capture_urb_complete().
USB core does not validate class-specific descriptor fields such
as bNrChannels, so drivers must verify them before use. If a
device provides bNrChannels = 0, frame_bytes becomes zero and is
later used as a divisor in the URB completion handlers, leading
to a kernel crash.
Fixes: 63978ab3e3 ("sound: add Edirol UA-101 support")
Cc: stable@vger.kernel.org
Signed-off-by: SeungJu Cheon <suunj1331@gmail.com>
Link: https://patch.msgid.link/20260426111239.103296-1-suunj1331@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device, just like the Playstation 5's DualSense, has a volume
that's too low, hid-playstation solves this by raising the minimum
volume on the device itself by sending an output report, third party PS5
controllers/accessories do not support this output report format, so we
apply a quirk to raise the minimum volume by 6dB.
Signed-off-by: Rosalie Wanders <rosalie@mailbox.org>
Link: https://patch.msgid.link/20260426025520.3985-2-rosalie@mailbox.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kconfiglint reports:
M004: 'snd-hda-codec-cmedia-y' assigned with ':=' but was already
assigned at line 5; previous value is overwritten
sound/hda/codecs/Makefile contains duplicate entries for the C-Media
codec driver — both the composite module definition and the obj-* build
target appear twice:
Line 5: snd-hda-codec-cmedia-y := cmedia.o
Line 10: snd-hda-codec-cmedia-y := cmedia.o (duplicate)
Line 24: obj-$(CONFIG_SND_HDA_CODEC_CMEDIA) += snd-hda-codec-cmedia.o
Line 29: obj-$(CONFIG_SND_HDA_CODEC_CMEDIA) += snd-hda-codec-cmedia.o (duplicate)
This file was created by commit 6014e9021b ("ALSA: hda: Move codec
drivers into sound/hda/codecs directory") which
moved codec drivers from sound/pci/hda/ to sound/hda/codecs/. In that
initial file, cmedia appeared once in each section.
Immediately after, commit aeeb85f26c ("ALSA: hda: Split Realtek
HD-audio codec driver") reordered the entries and
inserted cmedia at new positions near the top of each section, as part
of splitting out the Realtek driver. However, the original cmedia entries
were not removed during this reordering, creating duplicates of both
lines. The second assignment harmlessly overwrites the first with the
same value, and the second obj-* line causes the module to be listed
twice — neither causes a build failure, but both are dead code.
Remove the duplicate entries (second occurrence of each).
Assisted-by: Claude:claude-opus-4-6 kconfiglint
Signed-off-by: Sasha Levin <sashal@kernel.org>
Link: https://patch.msgid.link/20260426000327.56079-1-sashal@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Firmware 2417 for the Scarlett 4th Gen Solo, 2i2, and 4i4 added two
new front-panel features: a LED brightness setting (High/Medium/Low)
and an idle sleep timeout. Add ALSA controls to expose them:
- "Front Panel Brightness": enum (High/Medium/Low)
- "Front Panel Sleep Time": integer, seconds, capped at 86400 (24h)
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/1f9785ef76b9e97f785dfa4b91876a19f3c20c8e.1777153011.git.g@b4.vu
The device info's min_firmware_version field encoded the oldest
firmware the driver supports on each device. With the config_sets
array in place, the first entry's from_firmware_version carries the
same meaning (it's the oldest firmware range any config_set applies
to). Merge the two by dropping min_firmware_version from
scarlett2_device_info and reading config_sets[0].from_firmware_version
at the three call sites that used it.
No functional change.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/f2ca214b39c773c186adafc8726d6ff79f198459.1777151532.git.g@b4.vu
The Scarlett 2i2 Gen 4 firmware 2417 moved the direct monitor gain
parameters, so we now need to allow each device to list multiple
scarlett2_config_set entries, one per applicable firmware version
range, and pick the matching one at probe time.
No functional change yet: each device gets a single config_sets
entry whose from_firmware_version matches the existing
min_firmware_version (0 where none was set). This both prepares for
selection and lets a follow-up commit remove the now-redundant
min_firmware_version field.
scarlett2_count_io() depends on the resolved config_set so it moves
out of scarlett2_init_private() into snd_scarlett2_controls_create()
after the firmware version has been read.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/ae1695b4c4825f365b4c86b22174035f742807e3.1777151532.git.g@b4.vu
The Agilex7-M is a rebranded version of the original Agilex SoC. The
Agilex7-M SoC has the same core peripherals as the Agilex device.
This change is to document the Agilex7m devkit which has the Agilex7-M
device. The Agilex7-M SoC supports DDR4, DDR5, LPDDR5, PCIE 5.0(x16), but
not QSPI.
Also, now that Altera has separated from Intel, use the "altr" company
prefix.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
