Add the MSI Vector A16 HX A8WHG (board MS-15MM) to the DMI quirk table
to enable DMIC support. This laptop uses an AMD Ryzen 9 7945HX (Dragon
Range) with the ACP6x audio coprocessor (rev 0x62) and a Realtek ALC274
codec. The built-in digital microphone is connected via the ACP PDM
interface and requires this DMI entry to be activated.
Tested on MSI Vector A16 HX A8WHG with kernel 6.8.0-107 (Ubuntu 24.04).
DMIC capture device appears as 'acp6x' and records audio correctly.
Signed-off-by: Ihor Uzlov <igor.uzlov@gmail.com>
Link: https://patch.msgid.link/20260410094553.24654-1-igor.uzlov@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the open coded intel_fb_needs_pot_stride_remap() check
inside intel_fb_view_init() with the real thing.
The current check doesn't have the intel_fb_uses_dpt() in there, but
that is the only situation when we use the remapped view, and thus
was always implied.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260407155053.32156-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Replace the naked GTT view type checks with the new
i915_gtt_view_is_*() helpers. This isolates some of
the code from GTT view implementation details.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260407155053.32156-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
I915_GTT_VIEW_ROTATED is going away and being replaced by just
I915_GTT_VIEW_REMAPPED, so we're going to need another way to
determine if the view is rotated or not (since width/height
will need to be swapped when operating on the destination
coordinate space). Provide small helper functions to hide
such implementation details from most of the code using GTT views.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260407155053.32156-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
This codec driver depended on the legacy GPIO API, and nothing
in the kernel is defining the platform data, so get rid of this.
Two in-kernel device trees are defining this codec using
undocumented device tree properties, so support these for now.
The same properties can be defined using software nodes if board
files are desired. The device tree use the "-gpio" rather than
"-gpios" suffix but the GPIO DT parser will deal with that.
Since there may be out of tree users, migrate to GPIO descriptors,
drop the platform data that is unused, and assign the dac_clk the
value that was used in all platforms found in a historical dig,
and support setting the clock to the PLL using the undocumented
device tree property.
Add some menuconfig so the codec can be selected and tested.
Signed-off-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260409-asoc-uda1380-v3-1-b3d5a53f31be@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently create a single DPT for the entire FB, so we can't
actually do the per-plane remap. Reject it for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260407155053.32156-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
`ip6t_eui64`, `xt_mac`, the `bitmap:ip,mac`, `hash:ip,mac`, and
`hash:mac` ipset types, and `nf_log_syslog` access `eth_hdr(skb)`
after either assuming that the skb is associated with an Ethernet
device or checking only that the `ETH_HLEN` bytes at
`skb_mac_header(skb)` lie between `skb->head` and `skb->data`.
Make these paths first verify that the skb is associated with an
Ethernet device, that the MAC header was set, and that it spans at
least a full Ethernet header before accessing `eth_hdr(skb)`.
Suggested-by: Florian Westphal <fw@strlen.de>
Tested-by: Ren Wei <enjou1224z@gmail.com>
Signed-off-by: Zhengchuan Liang <zcliangcn@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Florian Westphal <fw@strlen.de>
Drop packets if their ttl/hl is too small for forwarding.
Fixes: d32de98ea7 ("netfilter: nft_fwd_netdev: allow to forward packets via neighbour layer")
Signed-off-by: Florian Westphal <fw@strlen.de>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Use the TRAILING_OVERLAP() helper to fix the following warnings:
1 net/netfilter/x_tables.c:816:39: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
1 net/netfilter/x_tables.c:811:39: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
This helper creates a union between a flexible-array member (FAM)
and a set of members that would otherwise follow it. This overlays
the trailing members onto the FAM while preserving the original
memory layout.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
UDP-Lite (RFC 3828) socket support was recently retired from the core
networking stack. As a follow-up of that, drop the connection tracker
and NAT support for UDP-Lite in Netfilter.
This patch removes CONFIG_NF_CT_PROTO_UDPLITE and scrubs UDP-Lite
awareness from the conntrack core, NAT core, nft_ct, and ctnetlink.
Please note that stateless packet inspection, matching, ipsets or
logging support for IPPROTO_UDPLITE is preserved.
As conntrack no longer extracts UDP-Lite ports or tracks its L4 state,
when performing NAT the UDP-Lite checksum cannot be updated anymore.
That is an expected and acceptable consequence of removing UDP-Lite
conntrack module.
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Originally this did not matter because defrag was enabled once per netns
and only disabled again on netns dismantle. When this got changed I should
have adjusted checkentry to not leave defrag enabled on error.
Fixes: de8c12110a ("netfilter: disable defrag once its no longer needed")
Signed-off-by: Florian Westphal <fw@strlen.de>
Add pr_fmt to prefix log messages with the module name for
easier debugging in dmesg.
Add checkentry functions for IPv4 (ttl_mt_check) and IPv6
(hl_mt6_check) to validate the match mode at rule registration
time, rejecting invalid modes with -EINVAL.
The evaluation function returns false in case the mode is
unknown, so this is a cleanup, not a bug fix.
Signed-off-by: Marino Dzalto <marino.dzalto@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reject names that lack a \0 character and reject the empty string as
well. iptables allows this but it fails to re-parse iptables-save output
that contain such rules.
Signed-off-by: Florian Westphal <fw@strlen.de>
Allow the default load factor for the connection and service tables
to be configured.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Florian Westphal <fw@strlen.de>
Add /proc/net/ip_vs_status to show current state of IPVS.
The motivation for this new /proc interface is to provide the output
for the users to help them decide when to tune the load factor for
hash tables, which is possible with the new sysctl knobs coming in
followup patch.
The output also includes information for the kthreads used for stats.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Florian Westphal <fw@strlen.de>
As conn_tab is per-net, better to show the current hash table size
to users instead of the ip_vs_conn_tab_size (max).
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Florian Westphal <fw@strlen.de>
Remove duplicate 'the' in the CMDLINE config help text.
Signed-off-by: Michael Ugrin <mugrinphoto@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Merge cpufreq updates for 7.1-rc1:
- Update qcom-hw DT bindings to include Eliza hardware (Abel Vesa)
- Update cpufreq-dt-platdev blocklist (Faruque Ansari)
- Minor updates to driver and dt-bindings for Tegra (Thierry Reding,
Rosen Penev)
- Add MAINTAINERS entry for CPPC driver (Viresh Kumar)
- Add support for new features: CPPC performance priority, Dynamic EPP,
Raw EPP, and new unit tests for them to amd-pstate (Gautham Shenoy,
Mario Limonciello)
- Fix sysfs files being present when HW missing and broken/outdated
documentation in the amd-pstate driver (Ninad Naik, Gautham Shenoy)
- Pass the policy to cpufreq_driver->adjust_perf() to avoid using
cpufreq_cpu_get() in the .adjust_perf() callback in amd-pstate which
leads to a scheduling-while-atomic bug (K Prateek Nayak)
- Clean up dead code in Kconfig for cpufreq (Julian Braha)
- Remove max_freq_req update for pre-existing cpufreq policy and add a
boost_freq_req QoS request to save the boost constraint instead of
overwriting the last scaling_max_freq constraint (Pierre Gondois)
- Embed cpufreq QoS freq_req objects in cpufreq policy so they all
are allocated in one go along with the policy to simplify lifetime
rules and avoid error handling issues (Viresh Kumar)
- Use DMI max speed when CPPC is unavailable in the acpi-cpufreq
scaling driver (Henry Tseng)
- Switch policy_is_shared() in cpufreq to using cpumask_nth() instead
of cpumask_weight() because the former is more efficient (Yury Norov)
- Use sysfs_emit() in sysfs show functions for cpufreq governor
attributes (Thorsten Blum)
- Update intel_pstate to stop returning an error when "off" is written
to its status sysfs attribute while the driver is already off (Fabio
De Francesco)
- Include current frequency in the debug message printed by
__cpufreq_driver_target() (Pengjie Zhang)
* pm-cpufreq: (38 commits)
cpufreq/amd-pstate: Add POWER_SUPPLY select for dynamic EPP
MAINTAINERS: amd-pstate: Step down as maintainer, add Prateek as reviewer
cpufreq: Pass the policy to cpufreq_driver->adjust_perf()
cpufreq/amd-pstate: Pass the policy to amd_pstate_update()
cpufreq/amd-pstate-ut: Add a unit test for raw EPP
cpufreq/amd-pstate: Add support for raw EPP writes
cpufreq/amd-pstate: Add support for platform profile class
cpufreq/amd-pstate: add kernel command line to override dynamic epp
cpufreq/amd-pstate: Add dynamic energy performance preference
Documentation: amd-pstate: fix dead links in the reference section
cpufreq/amd-pstate: Cache the max frequency in cpudata
Documentation/amd-pstate: Add documentation for amd_pstate_floor_{freq,count}
Documentation/amd-pstate: List amd_pstate_prefcore_ranking sysfs file
Documentation/amd-pstate: List amd_pstate_hw_prefcore sysfs file
amd-pstate-ut: Add a testcase to validate the visibility of driver attributes
amd-pstate-ut: Add module parameter to select testcases
amd-pstate: Introduce a tracepoint trace_amd_pstate_cppc_req2()
amd-pstate: Add sysfs support for floor_freq and floor_count
amd-pstate: Add support for CPPC_REQ2 and FLOOR_PERF
x86/cpufeatures: Add AMD CPPC Performance Priority feature.
...
In current linux.git, gnttab_suspend() and gnttab_resume() are defined
and declared unconditionally. However, their only in-tree callers reside
in drivers/xen/manage.c, which are guarded by CONFIG_HIBERNATE_CALLBACKS.
Match the helper scope to their callers by wrapping the definitions in
CONFIG_HIBERNATE_CALLBACKS and providing no-op stubs in the header. This
fixes the config-scope mismatch and reduces the code footprint when
hibernation callbacks are disabled.
Signed-off-by: Pengpeng Hou <pengpeng.hou@isrc.iscas.ac.cn>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260310080800.742223-1-pengpeng.hou@isrc.iscas.ac.cn>
When the console out buffer is filled, __write_console() will return 0
as it cannot send any data. domU_write_console() will then spin in
`while (len)` as len doesn't decrement until xenconsoled attaches. This
would block a domU and nullify the parallelism of Hyperlaunch until dom0
userspace starts xenconsoled, which empties the buffer.
Xen 4.21 added a connection field to the xen console page. This is set
to XENCONSOLE_DISCONNECTED (1) when a domain is built, and xenconsoled
will set it to XENCONSOLE_CONNECTED (0) when it connects.
Update the hvc_xen driver to check the field. When the field is
disconnected, drop the write with -ENOTCONN. We only drop the write
when the field is XENCONSOLE_DISCONNECTED (1) to try for maximum
compatibility. The Xen toolstack has historically zero initialized the
console, so it should see XENCONSOLE_CONNECTED (0) by default. If an
implemenation used uninitialized memory, only checking for
XENCONSOLE_DISCONNECTED could have the lowest chance of not connecting.
This lets the hyperlaunched domU boot without stalling. Once dom0
starts xenconsoled, xl console can be used to access the domU's hvc0.
Paritally sync console.h from xen.git to bring in the new field.
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Jason Andryuk <jason.andryuk@amd.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260318235326.14568-1-jason.andryuk@amd.com>
Commit af85de5a9f ("xen: swiotlb: Switch to physical
address mapping callbacks") renamed xen_swiotlb_unmap_page()
to xen_swiotlb_unmap_phys(). The comment in
xen_swiotlb_unmap_sg() had already been missing the xen_
prefix (reading swiotlb_unmap_page()), and the rename only
changed _page to _phys without correcting this, leaving it
as swiotlb_unmap_phys(). Fix the reference to use the
correct function name xen_swiotlb_unmap_phys().
Assisted-by: unnamed:deepseek-v3.2 coccinelle
Signed-off-by: Kexin Sun <kexinsun@smail.nju.edu.cn>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260321110039.8905-1-kexinsun@smail.nju.edu.cn>
setup_shutdown_watcher() registers shutdown_watch first, then the sysrq
watch, and finally publishes the supported feature-* nodes in xenstore.
If sysrq watch registration fails, or xenbus_printf() fails after one or
more feature nodes were created, the function returns immediately without
undoing the earlier setup.
This leaves the system in a partially initialized state, with registered
watches and/or stale xenstore entries despite the function reporting
failure.
Unwind the partial setup before returning an error by unregistering any
watches that were already registered and removing feature nodes that were
already published.
Signed-off-by: GuoHan Zhao <zhaoguohan@kylinos.cn>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260407022443.12971-1-zhaoguohan@kylinos.cn>
The error path after scx_bpf_create_dsq(real_dsq_id, ...) was reporting
test_dsq_id instead of real_dsq_id in the error message, which would
mislead debugging.
Signed-off-by: fangqiurong <fangqiurong@kylinos.cn>
Signed-off-by: Tejun Heo <tj@kernel.org>
Detect some corrupted extent cases during metadata parsing rather
than letting them result in harmless decompression failures later:
- For full-reference compressed extents, the compressed size must
not exceed the decompressed size, which is a strict on-disk
layout constraint;
- For plain (shifted/interlaced) extents, the decoded size must
not exceed the encoded size, even accounting for partial decoding.
Both ways work but it should be better to report illegal extents as
metadata layout violations rather than deferring as decompression
failure.
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
- Remove EROFS_MAP_ENCODED since it was always set together with
EROFS_MAP_MAPPED for compressed extents and checked redundantly;
- Replace the EROFS_MAP_FULL_MAPPED flag with the opposite
EROFS_MAP_PARTIAL_MAPPED flag so that extents are implicitly
fully mapped initially to simplify the logic;
- Make fragment extents independent of EROFS_MAP_MAPPED since
they are not directly allocated on disk; thus fragment extents
are no longer twisted with mapped extents.
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
fdt_find_hyper_node() reads the raw compatible property and then derives
hyper_node.version from a prefix match before later printing it with %s.
Flat DT properties are external boot input, and this path does not prove
that the first compatible entry is NUL-terminated within the returned
property length.
Keep the existing flat-DT lookup path, but verify that the first
compatible entry terminates within the returned property length before
deriving the version suffix from it.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260405094005.5-arm-xen-v2-pengpeng@iscas.ac.cn>
* Add ops.quiescent() and ops.runnable() to the sched_change path.
When a queued task has one of its scheduling properties changed
(e.g. nice, affinity), it goes through dequeue() -> quiescent() ->
(property change callback, e.g. ops.set_weight()) -> runnable() ->
enqueue().
* Change && to || in ops.enqueue() condition. We want to enqueue tasks
that have a non-zero slice and are not in any DSQ.
* Call ops.dispatch() and ops.dequeue() only for tasks that have had
ops.enqueue() called. This is to account for tasks direct-dispatched
from ops.select_cpu().
* Add a note explaining that the pseudo-code provides a simplified view
of the task lifecycle and list some examples of cases that the
pseudo-code does not account for.
Fixes: a4f61f0a1a ("sched_ext: Documentation: Add ops.dequeue() to task lifecycle")
Signed-off-by: Kuba Piecuch <jpiecuch@google.com>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The format string says "device %p ... rdma cgroup %p" but the arguments
were passed as (cg, device), printing them in the wrong order.
Signed-off-by: cuitao <cuitao@kylinos.cn>
Signed-off-by: Tejun Heo <tj@kernel.org>
Inline Crypto Engine (ICE) supports wrapped key generation. While
registering crypto profile the supported key types are queried from ICE
driver. So the explicit check for RAW key is not needed.
Fixes: fd78e2b582 ("mmc: sdhci-msm: Add support for wrapped keys")
Signed-off-by: Neeraj Soni <neeraj.soni@oss.qualcomm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The VSP serves as an interface to memory and a compositor to the DU. It
therefore needs to be suspended after and resumed before the DU, to be
properly stopped and restarted in a controlled fashion driven by the DU
driver. This currently works by chance. Avoid relying on luck by
enforcing the correct suspend/resume ordering with device links.
Based on similar work done by Laurent Pinchart for R-Car DU.
commit db5be3a7d6 ("drm: rcar-du: Ensure correct suspend/resume
ordering with VSP")
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Link: https://patch.msgid.link/20260330144651.817338-1-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Clang 20 and 21 miscompute __builtin_object_size() when -fprofile-arcs
is active on 32-bit UML targets, which passes incorrect object size
calculations for local variables through always_inline copy_to_user()
and check_copy_size(), causing spurious compile-time errors:
include/linux/ucopysize.h:52:4: error: call to '__bad_copy_from' declared with 'error' attribute: copy source size is too small
The regression was introduced in LLVM commit 02b8ee281947 ("[llvm]
Improve llvm.objectsize computation by computing GEP, alloca and malloc
parameters bound"), which shipped in Clang 20. It was fixed in LLVM
by commit 45b697e610fd ("[MemoryBuiltins] Consider index type size
when aggregating gep offsets"), which was backported to the LLVM 22.x
release branch.
The bug requires 32-bit UML + GCOV_PROFILE_ALL (which uses -fprofile-arcs),
though the exact trigger depends on optimizer decisions influenced by other
enabled configs.
Prevent the bad combination by disabling UML's ARCH_HAS_GCOV_PROFILE_ALL
on 32-bit when using Clang 20.x or 21.x.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202604030531.O6FveVgn-lkp@intel.com/
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Assisted-by: Claude:claude-opus-4-6[1m]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20260409052038.make.995-kees@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
devm_kzalloc() failure in tegra_gpio_probe() returns -ENODEV, which
indicates "no such device". The correct error code for a memory
allocation failure is -ENOMEM.
Signed-off-by: Samasth Norway Ananda <samasth.norway.ananda@oracle.com>
Link: https://patch.msgid.link/20260409185853.2163034-1-samasth.norway.ananda@oracle.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Commit 3bce3fdd1f ("drm: rcar-du: Don't leak device_link to CMM")
refactored CMM handling, and introduced an incorrect test for CMM
availability. When no CMM is present, the rcrtc->cmm field is NULL,
testing rcrtc->cmm->dev causes a NULL pointer dereference. This slipped
through testing as all tests were run with the CMM present.
Fix this issue by correctly testing for rcrtc->cmm.
Fixes: 3bce3fdd1f ("drm: rcar-du: Don't leak device_link to CMM")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/dri-devel/CAMuHMdXomz9GFDqkBjGX9Sda_GLccPcrihvFbOz0GAitDVNTbw@mail.gmail.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260408124205.1962448-1-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Kconfig improvement for ethosu.
-----BEGIN PGP SIGNATURE-----
iJUEABMJAB0WIQTkHFbLp4ejekA/qfgnX84Zoj2+dgUCaddf9AAKCRAnX84Zoj2+
dvihAYCtQsSwH6VCpDf9bknrlqXpiUu+JlU2tSrK5plyTioCfFmdE1EhZmy7RJRo
EAFpb4ABf16BBat7a3SJ/8KYeNtoYggURn4JvNKKPMF1lSYa9PNmKQsJsfMGmHt5
IIKRgFYQXw==
=/nuD
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2026-04-09' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
Several fixes for v3d about memory leak, runtime PM, and locking, and a
Kconfig improvement for ethosu.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patch.msgid.link/20260409-omniscient-tomato-coucal-edbadc@penduick
The ../generated/protos.a rule had a spurious leading space before the
target name. In make, target rules must start at column 0; only recipe
lines are indented with a tab. The extra space caused make to misparse
the rule.
Remove the leading space to match the style of the adjacent
../lib/ynl.a rule.
Fixes: e0aa0c6175 ("tools: ynl: move samples to tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20260408-ynl_makefile-v1-1-f9624acc2ad9@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
People (do people still write code or is it all AI?) seem to not
get that ksft_run() can only be called once. If we call it
multiple times KTAP parsers will likely cut off after the first
batch has finished.
Link: https://patch.msgid.link/20260408221952.819822-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable ret is assigned a value at all places where it is used;
There is no need to assign a value when it is initially defined.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://patch.msgid.link/20260408032051.3096449-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fbnic_up() calls netif_tx_start_all_queues(), which only clears
__QUEUE_STATE_DRV_XOFF. If qdisc backlog has accumulated on any TX
queue before the reconfiguration (e.g. ring resize via ethtool -G),
start does not call __netif_schedule() to kick the qdisc, so the
pending backlog is never drained and the queue stalls.
Switch to netif_tx_wake_all_queues(), which clears DRV_XOFF and also
calls __netif_schedule() on every queue, ensuring any backlog that
built up before the down/up cycle is promptly dequeued.
Fixes: bc6107771b ("eth: fbnic: Allocate a netdevice and napi vectors with queues")
Signed-off-by: Mohsin Bashir <hmohsin@meta.com>
Link: https://patch.msgid.link/20260408002415.2963915-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing dma_rmb() in airoha_qdma_rx_process routine to make sure the
DMA read operations are completed when the NIC reports the processing on
the current descriptor is done. Moreover, add missing READ_ONCE() in
airoha_qdma_rx_process() for DMA descriptor control fields in order to
avoid any compiler reordering.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260407-airoha_qdma_rx_process-fix-reordering-v3-1-91c36e9da31f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Justin Chen says:
====================
net: bcmgenet: fix queue lock up
We have been seeing reports of logs like this.
[ 41.761198] bcmgenet 1001300000.ethernet eth0: NETDEV WATCHDOG: CPU: 0: transmit queue 2 timed out 10039 ms
[ 43.745198] bcmgenet 1001300000.ethernet eth0: NETDEV WATCHDOG: CPU: 0: transmit queue 2 timed out 12023 ms
[ 45.729198] bcmgenet 1001300000.ethernet eth0: NETDEV WATCHDOG: CPU: 0: transmit queue 2 timed out 14007 ms
We have two issues. The persistent queue timeouts and the eventual
lock up of the entire transmit.
We address the lock up issue first. The queue timeouts are due to
a fundamental design issue not a bug perse. Timeouts still persist,
but we should no longer lock up.
====================
Link: https://patch.msgid.link/20260406175756.134567-1-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bcmgenet_timeout handler tries to take down all tx queues when
a single queue times out. This is over zealous and causes many race
conditions with queues that are still chugging along. Instead lets
only restart the timed out queue.
Fixes: 13ea657806 ("net: bcmgenet: improve TX timeout")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406175756.134567-4-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reclaiming the tx queue we fast forward the write pointer to
drop any data in flight. These dropped frames are not added back
to the pool of free bds. We also need to tell the netdev that we
are dropping said data.
Fixes: f1bacae8b6 ("net: bcmgenet: support reclaiming unsent Tx packets")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406175756.134567-3-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The write_ptr points to the next open tx_cb. We want to return the
tx_cb that gets rewinded, so we must rewind the pointer first then
return the tx_cb that it points to. That way the txcb can be correctly
cleaned up.
Fixes: 876dbadd53 ("net: bcmgenet: Fix unmapping of fragments in bcmgenet_xmit()")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406175756.134567-2-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For non-PREEMPT_RT kernels, the IRQ handler runs with interrupts
disabled, allowing the use of napi_schedule_irqoff() to save a pair of
local_irq_{save,restore} operations. For PREEMPT_RT kernels,
napi_schedule_irqoff() behaves identically to napi_schedule().
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://patch.msgid.link/20260407-macb-napi-irqoff-v1-1-61bec60047d7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ppp_destroy_{channel,interface} are always called after
refcount_dec_and_test().
To reduce boilerplate code, consolidate the decrements by moving them
into the two functions. To reflect this change in semantics, rename the
functions to ppp_release_*.
Signed-off-by: Qingfang Deng <qingfang.deng@linux.dev>
Link: https://patch.msgid.link/20260407094058.257246-1-qingfang.deng@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
