On stm32mp1x boards, enable the debug bus so we always try to probe
the debug peripherals, if their status and the debug configuration
allow it.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Link: https://lore.kernel.org/r/20260226-debug_bus-v6-8-5d794697798d@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Some peripherals cannot be probed if a debug configuration is not set
in the BSEC.
Introduce a debug bus that will check the debug subsystem accessibility
before probing these peripheral drivers.
Add Coresight peripheral nodes under this bus and add the appropriate
access-controllers property to the HDP node.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Link: https://lore.kernel.org/r/20260226-debug_bus-v6-7-5d794697798d@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fix a typo in the ADXL380_PART_ID_REG macro name where it was
incorrectly defined as ADLX380_PART_ID_REG.
Also update its usage in adxl380_setup().
Signed-off-by: Nikhil Gautam <nikhilgtr@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The BeagleV Ahead board includes a micro HDMI connector (Type-D)
wired to the TH1520 SoC's HDMI transmitter.
Enable the display pipeline by adding the HDMI connector node,
connecting it to the HDMI controller, and activating the DPU
and HDMI nodes.
Signed-off-by: Robert Mazur <robert.mazur@imgtec.com>
Signed-off-by: Drew Fustini <fustini@kernel.org>
The driver uses its own definitions for HID requests.
This leads to duplication and obfuscation. Use HID's
definitions.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20260325143256.371854-2-oneukum@suse.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver uses its own definitions for HID requests.
This leads to duplication and obfuscation. Use HID's
definitions.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20260325143256.371854-1-oneukum@suse.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Without a reported resolution, userspace was assuming 1 unit/mm which
is wildly wrong: a regular smartphone is clearly not 2.4 meters tall.
Most applications do not care much for this kind of raw mm value,
but Phosh's on-screen keyboard would accidentally trigger swipe-to-close
gestures due to misinterpreting small movements as huge ones.
Do what the older goodix.c driver does and set the resolution to 10
units/mm to make sure the numbers calculated by userspace are reasonable.
Signed-off-by: Val Packett <val@packett.cool>
Link: https://patch.msgid.link/20260321073242.556253-1-val@packett.cool
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tiny SRCU's srcu_gp_start_if_needed() directly calls schedule_work(),
which acquires the workqueue pool->lock.
This causes a lockdep splat when call_srcu() is called with a scheduler
lock held, due to:
call_srcu() [holding pi_lock]
srcu_gp_start_if_needed()
schedule_work() -> pool->lock
workqueue_init() / create_worker() [holding pool->lock]
wake_up_process() -> try_to_wake_up() -> pi_lock
Also add irq_work_sync() to cleanup_srcu_struct() to prevent a
use-after-free if a queued irq_work fires after cleanup begins.
Tested with rcutorture SRCU-T and no lockdep warnings.
[ Thanks to Boqun for similar fix in patch "rcu: Use an intermediate irq_work
to start process_srcu()" ]
Signed-off-by: Joel Fernandes <joelagnelf@nvidia.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun@kernel.org>
Since commit c27cea4416 ("rcu: Re-implement RCU Tasks Trace in terms
of SRCU-fast") we switched to SRCU in BPF. However as BPF instrument can
happen basically everywhere (including where a scheduler lock is held),
call_srcu() now needs to avoid acquiring scheduler lock because
otherwise it could cause deadlock [1]. Fix this by following what the
previous RCU Tasks Trace did: using an irq_work to delay the queuing of
the work to start process_srcu().
[boqun: Apply Joel's feedback]
[boqun: Apply Andrea's test feedback]
Reported-by: Andrea Righi <arighi@nvidia.com>
Closes: https://lore.kernel.org/all/abjzvz_tL_siV17s@gpd4/
Fixes: commit c27cea4416 ("rcu: Re-implement RCU Tasks Trace in terms of SRCU-fast")
Link: https://lore.kernel.org/rcu/3c4c5a29-24ea-492d-aeee-e0d9605b4183@nvidia.com/ [1]
Suggested-by: Zqiang <qiang.zhang@linux.dev>
Tested-by: Andrea Righi <arighi@nvidia.com>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Joel Fernandes <joelagnelf@nvidia.com>
Signed-off-by: Boqun Feng <boqun@kernel.org>
When the srcutree.convert_to_big and srcutree.big_cpu_lim kernel boot
parameters specify initialization-time allocation of the srcu_node
tree for statically allocated srcu_struct structures (for example, in
DEFINE_SRCU() at build time instead of init_srcu_struct() at runtime),
init_srcu_struct_nodes() will attempt to dynamically allocate this tree
at the first run-time update-side use of this srcu_struct structure,
but while holding a raw spinlock. Because the memory allocator can
acquire non-raw spinlocks, this can result in lockdep splats.
This commit therefore uses the same SRCU_SIZE_ALLOC trick that is used
when the first run-time update-side use of this srcu_struct structure
happens before srcu_init() is called. The actual allocation then takes
place from workqueue context at the ends of upcoming SRCU grace periods.
[boqun: Adjust the sha1 of the Fixes tag]
Fixes: 175b45ed34 ("srcu: Use raw spinlocks so call_srcu() can be used under preempt_disable()")
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun@kernel.org>
Tree SRCU has used non-raw spinlocks for many years, motivated by a desire
to avoid unnecessary real-time latency and the absence of any reason to
use raw spinlocks. However, the recent use of SRCU in tracing as the
underlying implementation of RCU Tasks Trace means that call_srcu()
is invoked from preemption-disabled regions of code, which in turn
requires that any locks acquired by call_srcu() or its callees must be
raw spinlocks.
This commit therefore converts SRCU's spinlocks to raw spinlocks.
[boqun: Add Fixes tag]
Reported-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Fixes: c27cea4416 ("rcu: Re-implement RCU Tasks Trace in terms of SRCU-fast")
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
When alloc_and_link_pwqs() fails partway through the per-cpu allocation
loop, some pool_workqueues may have already been linked into wq->pwqs
via link_pwq(). The error path frees these pwqs with kmem_cache_free()
but never removes them from the wq->pwqs list, leaving dangling pointers
in the list.
Currently this is not exploitable because the workqueue was never added
to the global workqueues list and the caller frees the wq immediately
after. However, this makes sure that alloc_and_link_pwqs() doesn't leave
any half-baked structure, which may have side effects if not properly
cleaned up.
Fix this by unlinking each pwq from wq->pwqs before freeing it. No
locking is needed as the workqueue has not been published yet, thus
no concurrency is possible.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Try to be more explicit why the workqueue watchdog does not take
pool->lock by default. Spin locks are full memory barriers which
delay anything. Obviously, they would primary delay operations
on the related worker pools.
Explain why it is enough to prevent the false positive by re-checking
the timestamp under the pool->lock.
Finally, make it clear what would be the alternative solution in
__queue_work() which is a hotter path.
Signed-off-by: Petr Mladek <pmladek@suse.com>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The verifier log output may contain multiple lines that start with
18: (bf) r0 = r6
teach reg_bounds to look for lines that have ';' in them,
since reg_bounds test is looking for:
18: (bf) r0 = r6 ; R0=... R6=...
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Link: https://lore.kernel.org/r/20260325012242.45606-1-alexei.starovoitov@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch fixes an issue like:
where searching for the entity 'FU 11' could incorrectly match 'FU 113' first.
The driver should first perform an exact match on the full string name.
If no exact match is found, it can then fall back to a partial match.
Fixes: 48fa77af2f ("ASoC: SDCA: Add terminal type into input/output widget name")
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://patch.msgid.link/20260325110406.3232420-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of requesting interrupt normally and immediately disabling it
with call to disable_irq() use IRQF_NOAUTOEN to keep it disabled until
it is needed. This avoids a tiny window when interrupt is enabled but
not needed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Guard notation simplifies code.
Also use list_first_entry() instead of list_entry() to emphasize intent.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ref to nand-controller-legacy.yaml instead nand-controller.yaml to allow
legacy DT layout.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The modern NAND controller binding requires NAND chips to be described as
child nodes of the controller, for example:
nand-controller {
...
nand@0 {
/* raw NAND chip properties */
};
};
However, many existing device trees place NAND chip properties directly
within the controller node because those controllers support only a single
chip. This layout is still widely used by older platforms and by other DT
consumers such as U-Boot. Migrating all existing users to the new layout
will take time.
Several kernel drivers, such as ams-delta.c, davinci_nand.c and
fsmc_nand.c, still expect the legacy layout where raw NAND properties are
defined in the controller node.
To support both layouts during the transition:
- Extract NAND chip-related properties into separate schemas
(nand-property.yaml and raw-nand-property.yaml) from
nand-chip.yaml and raw-nand-chip.yaml.
- Introduce nand-controller-legacy.yaml to allow both the
legacy and modern layouts.
- Add a select condition in nand-controller.yaml to prevent
node name pattern matching for fsl,* NAND controllers.
Keep compatibility with existing device trees while allowing gradual
migration to the modern binding structure.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Above 104MHz when in fast dual or quad I/O reads, the delay between
address and data cycles is too short. It is possible to reach higher
frequencies, up to 166MHz, by adding a few more dummy cycles through the
setting of the HS bit. Improve the condition for enabling this bit, and
also make sure we set it at soon as we go over 104MHz.
Fixes: f1a91175fa ("mtd: spinand: winbond: Enable high-speed modes on w25n0xjw")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In Allwinner SoCs, user data can be added in OOB before each ECC data.
For older SoCs like A10, the user data size was the size of a register
(4 bytes) and was mandatory before each ECC step.
So, the A10 OOB Layout is:
[4Bytes USER_DATA_STEP0] [ECC_STEP0 bytes]
[4bytes USER_DATA_STEP1] [ECC_STEP1 bytes]
...
NB: the BBM is stored at the beginning of the USER_DATA_STEP0.
Now, for H6/H616 NAND flash controller, this user data can have a
different size for each step.
So, we are maximizing the user data length to use as many OOB bytes as
possible.
Fixes: 88fd4e4dea ("mtd: rawnand: sunxi: Add support for H616 nand controller")
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In sunxi_nand_hw_ecc_ctrl_init(), i is used as a loop index variable and
at the same time as the value used to set ECC mode in ECC control
register.
To prevent it from being re-used as a loop variable, let's change the
naming to ecc_mode.
No functional change.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
sunxi_nand_ooblayout_free() is only used in a code path where
engine_type == NAND_ECC_ENGINE_TYPE_ON_HOST
So the other cases can be removed.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In sunxi_nfc_hw_ecc_{read,write}_chunk(), the ECC step was forced to 0,
the reason is not trivial to get when reading the code.
The explanation is that, from the NAND flash controller perspective, we
are indeed at step 0 for user data length and ECC errors.
Just add a const value with an explanation to clarify things.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The user data length (4) has been replaced almost all over the file, but
2 places were forgotten.
The user data is placed before the ECC, for each step.
So, in sunxi_nfc_hw_ecc_read_extra_oob(), the offset of the user data in
OOB is indeed ((ecc->bytes + USER_DATA_SZ) * ecc->steps);
And in sunxi_nand_ooblayout_ecc(), the offset of the ECC chunk in OOB is
the same offset plus the current user data size:
section * (ecc->bytes + USER_DATA_SZ) + USER_DATA_SZ;
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
BBM is already part of USER_DATA section, so we should not remove it twice
This was working ok because we are on the safe size, advertising that
there was 2 bytes less available than in reality.
But we can't change old platforms, since it may lead to a different ECC
strength, so, introduce a legacy flag for old platforms, and switch the
new platforms to the correct count.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The available length is really USER_DATA_LEN - 2 instead of just 2 (the
user data length minus the BBM length)
USER_DATA_LEN being 4, that doesn't change anything now, but if
USER_DATA_LEN changes, it will.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add Intel Nova Lake-H LPSS PCI IDs.
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Co-developed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260313100337.3471-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
I and Qianhai are GPU R&D engineers at Loongson, specializing
in kernel driver development. We understand that the current
Loongson GPU driver lacks dedicated maintenance resources
because of some reasons.
As Loongson GPU driver developers, we have both the capability
and the responsibility to continuously maintain the Loongson
GPU driver, ensuring minimal impact on its users. After internal
discussions, our team has decided to recommend me and Qianhai
to take over the maintenance responsibilities, and recommend
Huacai, Mingcong and Ruoyao to help to review.
And We'll continue to maintain it for current supported chips
and drive future updates according to chip support plan.
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260320101012.22714-1-lvjianmin@loongson.cn
Deprecate simple-encoder and simple-display-pipe helpers in favor of
regular atomic helpers. Remove the related documentation. Add TODO
item for converting the remaining drivers.
These helpers have been deprecated for years and many drivers have
been updated to not use them. Still there are a few left and we
occasionally receive new drivers build upon them. Marking them as
deprecated will hopefully resolve these problems. The TODO items
should be easy enough for getting new voluteers started on DRM driver
development.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: David Lechner <david@lechnology.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260319160110.109610-17-tzimmermann@suse.de
With the conversion to regular atomic helpers, mipi-dbi's support
for simple-display helpers is unused. Removed it.
v2:
- remove unused connector from struct mipi_dbi_dev
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: David Lechner <david@lechnology.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260319160110.109610-16-tzimmermann@suse.de
Replace simple-display helpers with regular atomic helpers. Store the
pipeline elements in struct st7735r_device and initialize them as part
of probing the device. Use mipi-dbi's existing helpers and initializer
macros where possible.
Effectively open-codes the modesetting code in the initializer helpers
of mipi-dbi and simple-display. St7735r requires a custom helper for
CRTC enablement, and non-freeing cleanup of the pipeline.
v2:
- fix connector initialization
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: David Lechner <david@lechnology.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260319160110.109610-15-tzimmermann@suse.de
Rename the driver's device variable according to DRM conventions. No
functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: David Lechner <david@lechnology.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260319160110.109610-14-tzimmermann@suse.de
Rename the driver's device struct according to DRM conventions. Also
add a helper to upcast from struct drm_device. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: David Lechner <david@lechnology.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260319160110.109610-13-tzimmermann@suse.de
Replace simple-display helpers with regular atomic helpers. Store the
pipeline elements in struct st7586_device and initialize them as part
of probing the device. Use mipi-dbi's existing helpers and initializer
macros where possible.
Effectively open-codes the modesetting code in the initializer helpers
of mipi-dbi and simple-display. St7586 requires custom helpers for
various pipeline elements, and non-freeing cleanup of the pipeline.
v3:
- return early in st7586_plane_helper_atomic_update (David)
v2:
- fix connector initialization
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260319160110.109610-12-tzimmermann@suse.de
