Replace the open-coded backlog check with sk_acceptq_is_full().
The helper uses > instead of >=, which is the correct comparison
per commit 64a146513f ("[NET]: Revert incorrect accept queue
backlog changes."), and adds READ_ONCE() for proper memory ordering.
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Raf Dickson <rafdog35@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Link: https://patch.msgid.link/20260612045842.122207-1-rafdog35@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
WED_MON_AMSDU_ENG_CNT point to different entry by 'base+n*offset' mode,
correct the wed amsdu entry number in wed_amsdu_show().
Fixes: 3f3de094e8 ("net: ethernet: mtk_wed: debugfs: add WED 3.0 debugfs entries")
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Link: https://patch.msgid.link/20260612064501.203058-1-guanwentao@uniontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal says:
====================
netdevsim: add fake FT/CLS_FLOWER offload
v2: fix up error reporting via extack
shellcheck cleanups
sort config toggles
1) Enable nf_tables offload control plane testing in netdevsim. Tag
existing offload fn to allow error injection for testing rollback and abort
logic.
2) Add nft_offload selftest to exercise the control plane and error
unwind via fault injection.
====================
Link: https://patch.msgid.link/20260612092209.11966-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
... "phony", because its not testing offloads, it tests the control
plane code. Also test error unwind via fault injection framework.
For a proper test, real hardware would be required given we'd have
check if 'previously handed off to hardware' offload commands are
properly removed again on failure or rule flush.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20260612092209.11966-3-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The actual 'offload' is phony, all commands are ignored: this is only
useful to test control plane code.
Tag the existing callback to permit error injection to test rollback/abort
code in nf_tables. This is also for fuzzers - the fault injection
framework allows probabilistic error insertion.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20260612092209.11966-2-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In airoha_ppe_flush_sram_entries(), the outer "err" variable was never
updated when the inner loop variable shadowed it, causing the function
to always return 0 even when airoha_ppe_foe_commit_sram_entry() fails.
Drop the outer "err" variable and return directly on error, propagating
the error code from airoha_ppe_foe_commit_sram_entry() correctly.
Fixes: 620d7b91aa ("net: airoha: ppe: Flush PPE SRAM table during PPE setup")
Link: https://lore.kernel.org/netdev/6a2b40e4.4dd82583.3a5c46.e52f@mx.google.com/
Signed-off-by: Wayen.Yan <win847@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/6a2bd37a.4034e349.1b41bb.1caf@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- rust: fix I2cAdapter refcount double increment
- MAINTAINERS: minor updates
- imx: keep clock and pinctrl states consistent in runtime PM
- imx-lpi2c: fix DMA resource leaks on PIO fallback
- qcom-cci: fix NULL pointer dereference on remove
- riic: fix reset refcount leak on resume_noirq error path
- stm32f7: account for analog filter in timing computation
- tegra: fix suspend/resume handling in NOIRQ phase
- tegra: update Tegra410 I2C timings to match hardware specs
- MAINTAINERS: hand over I2C maintainership to Andi
-----BEGIN PGP SIGNATURE-----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=K2oD
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-7.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The biggest news here is that this is my last pull request as I2C
maintainer after 13.5 years. Starting with the 7.2 cycle, Andi Shyti
is taking over who helped me greatly maintaining the host drivers for
a while now. Thank you, Andi, and good luck with the subsystem. I'll
be around for help, of course.
Technically, there are two patches which might be a tad large for this
late cycle, but most of them is explaining comments, so I think they
are suitable.
- MAINTAINERS:
- hand over I2C maintainership to Andi
- minor updates
- rust: fix I2cAdapter refcount double increment
- imx: keep clock and pinctrl states consistent in runtime PM
- imx-lpi2c: fix DMA resource leaks on PIO fallback
- qcom-cci: fix NULL pointer dereference on remove
- riic: fix reset refcount leak on resume_noirq error path
- stm32f7: account for analog filter in timing computation
- tegra:
- fix suspend/resume handling in NOIRQ phase
- update Tegra410 I2C timings to match hardware specs"
* tag 'i2c-for-7.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
dt-bindings: i2c: mux-gpio: name correct maintainer
MAINTAINERS: hand over I2C to Andi Shyti
i2c: imx-lpi2c: fix resource leaks switching to devm_dma_request_chan()
MAINTAINERS: i2c: designware: Remove inactive reviewer
i2c: tegra: Fix NOIRQ suspend/resume
i2c: tegra: Update Tegra410 I2C timing parameters
i2c: qcom-cci: Fix NULL pointer dereference in cci_remove()
i2c: stm32f7: fix timing computation ignoring i2c-analog-filter
i2c: imx: fix clock and pinctrl state inconsistency in runtime PM
i2c: riic: fix refcount leak in riic_i2c_resume_noirq()
rust: i2c: fix I2cAdapter refcounts double increment
redundant information (Nick Hu)
- Remove the TCIU8 interrupt bindings on Renesas because it should not
be described as the documentation marked reserved and fix the
conditional reset line for the RZ/{T2H,N2H} (Cosmin Tanislav)
- Add the StarFive JHB100 clint DT bindings compatible string (Ley
Foon Tan)
- Extend schema condition for interrupts to cover D1 compatible
variant an add the D1 hstimer support (Michal Piekos)
- Update the ARM architected timer support to handle the ACPI GTDT v3
format and the EL2 virtual timer, enabling Linux to use the most
appropriate timer when running with VHE, while also fixing several
Device Trees to accurately reflect the underlying hardware (Marc
Zyngier)
- Cleanup and add the clocksource and the clockevent in the TI DM
timer (Markus Schneider-Pargmann)
- Add the multiple watchdogs support in the tegra186 and
tegra234. Dedicate one as a kernel watchdog (Kartik Rajput)
- Add the NXP clocksource selection for the scheduler in the Kconfig
(Enric Balletbo i Serra)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmoq0wgACgkQqDIjiipP
6E8Ungf/SNh8g6NbP6Gqg5Vs0WxlM75EGeJsryLFXooXjLa2TJVh5/i3fm0kh8uG
xi/cs2NLWsAMezLwLQhmB+mMGzsZh4WswgTu7EqCkXgd+TMqV9Wi57vU18nOX8gs
XKGxCUqg+kOGAoj5FsZLyq6Sy/NfMHxxY2kSq4oUG2o/xWaLYwDvRcW8iXXAjj/U
321YrB77lJ+FefUiZveiykf+QjzOXkiPlJTGroOcEL8F/Hm5YMBDfAtW6zslfiFw
KmOjraY9wkRqQVT9xFeJrssCpn8iCzb9DXpKQUkTAahYgVc0Im7g3p/GOkUHmQFE
KfvgBNO/tt3+m/Q8FO3la8gPF6LuaA==
=upV/
-----END PGP SIGNATURE-----
Merge tag 'timers-v7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/daniel.lezcano/linux into timers/clocksource
Pull clocksource/driver updates from Daniel Lezcano:
- Remove the sifive,fine-ctr-bits property bindings because it is a
redundant information (Nick Hu)
- Remove the TCIU8 interrupt bindings on Renesas because it should not
be described as the documentation marked reserved and fix the
conditional reset line for the RZ/{T2H,N2H} (Cosmin Tanislav)
- Add the StarFive JHB100 clint DT bindings compatible string (Ley
Foon Tan)
- Extend schema condition for interrupts to cover D1 compatible
variant an add the D1 hstimer support (Michal Piekos)
- Update the ARM architected timer support to handle the ACPI GTDT v3
format and the EL2 virtual timer, enabling Linux to use the most
appropriate timer when running with VHE, while also fixing several
Device Trees to accurately reflect the underlying hardware (Marc
Zyngier)
- Cleanup and add the clocksource and the clockevent in the TI DM
timer (Markus Schneider-Pargmann)
- Add the multiple watchdogs support in the tegra186 and
tegra234. Dedicate one as a kernel watchdog (Kartik Rajput)
- Add the NXP clocksource selection for the scheduler in the Kconfig
(Enric Balletbo i Serra)
Link: https://lore.kernel.org/all/1e55e8d6-8024-4f17-8620-ab3385465d76@oss.qualcomm.com
In do_cpu_nanosleep(), posix_cpu_timer_create() takes a pid reference
via get_pid() and stores it in timer.it.cpu.pid. If the subsequent
posix_cpu_timer_set() call fails, the function returns immediately
without calling posix_cpu_timer_del() to release the pid reference,
causing a leak.
Fix it by calling posix_cpu_timer_del() before the unlock-and-return
on the error path, consistent with the other exit paths in the same
function.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: WenTao Liang <vulab@iscas.ac.cn>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260611161738.97043-1-vulab@iscas.ac.cn
The /proc/interrupt handling rework dropped a 's' in the thermal event
printout, which breaks the thermal test in the Intel LKVS suite.
Bring the important letter back.
Fixes: 2b57c69917 ("x86/irq: Make irqstats array based")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Closes: https://lore.kernel.org/oe-lkp/202606121325.97b29701-lkp@intel.com
Teddy reported that a XEN HVM has a long boot delay, which was bisected to
the recent enhancements to the negative motion detection. It turned out
that the jiffies clocksource is used in early boot before it is registered,
which leaves the max_delta_raw field at zero. That causes the read out to
be clamped to the max delta of 0, which means time is not making progress.
Cure it by ensuring that it is initialized before its first usage in
timekeeping_init().
Fixes: 76031d9536 ("clocksource: Make negative motion detection more robust")
Reported-by: Teddy Astie <teddy.astie@vates.tech>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Tested-by: Teddy Astie <teddy.astie@vates.tech>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/87y0gn3fve.ffs@fw13
Closes: https://lore.kernel.org/all/1780914594.8631fc262581453bbf619ec5b2062170.19ea6c8227b000701b@vates.tech
The "ti,n-factor" binding and examples allow negative correction
values. Reading it as u32 makes the helper type disagree with the
documented signed value and hides real schema mismatches.
Use the signed helper so the DT access matches the s32 value stored by
the driver.
Assisted-by: Codex:gpt-5-5
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20260612215332.1889497-1-robh@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Offsets and lengths need to be validated against the dma alignment. This
check was skipped for sufficiently a small bio with a single bvec, which
may allow an invalid request dispatched to the driver. Force the
validation for an unaligned bvec by forcing the bio split path that
handles this condition.
Fixes: 7eac331869 ("iomap: simplify direct io validity check")
Fixes: 5ff3f74e14 ("block: simplify direct io validity check")
Reported-by: Carlos Maiolino <cem@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://patch.msgid.link/20260612223205.465913-1-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
syzbot reported a possible circular locking dependency in udp_sendmsg()
where fs_reclaim can be triggered while holding sk_lock, and fs_reclaim
can eventually depend on another sk_lock (e.g., if NBD is used for swap
or writeback and NBD uses TLS/TCP which acquires sk_lock).
Since the UDP socket and the NBD TCP/TLS socket are different, this is a
false positive. Fix this by reclassifying NBD sockets to a separate lock
class when they are added to the NBD device.
This is similar to what nvme-tcp and other network block devices do.
Fixes: ffa1e7ada4 ("block: Make request_queue lockdep splats show up earlier")
Reported-by: syzbot+607cdcf978b3e79da878@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/6a2cdafe.428ffe26.258b27.0161.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260613042619.1108126-1-edumazet@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_recv() and io_recvzc() are the odd ones out, as they checks for
whether POLL_FIRST should be honored before checking if the file is a
socket. It doesn't really matter, but might as well make it consistent
across all receive and send types.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the tctx fallback running its entries directly, the per-ctx
fallback work has a single user left: moving local (DEFER_TASKRUN)
task_work entries out of a ring that is going away. Both of its call
sites are process context and don't hold ->uring_lock, the same
conditions the deferred fallback work itself ran under - so run the
entries in cancel mode right there instead, and rename the helper to
io_cancel_local_task_work() to match what it now does.
With that, ->fallback_llist, ->fallback_work, io_fallback_req_func()
and __io_fallback_tw() can all go away, along with the fallback work
flushing in the ring exit and cancel paths. Requests that get
orphaned by an exiting task now run via the tctx fallback work, which
the ring exit side implicitly waits on through the ctx refs those
requests hold.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The fallback work drains the tctx queue only to redistribute the entries
into the per-ctx fallback lists, bouncing them through a second
(per-ctx) work item before they finally run. That made sense when the
producer side did the draining and could be in any context, but the
fallback work is a regular process context kworker: it can just run the
entries itself. Reuse the normal run loop - if run from the fallback
kernel thread, ts.cancel will get set, and the work terminated.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Like the local task_work list, the normal (tctx) task_work list is an
llist, and hence needs the O(n) llist_reverse_order() pass before
running entries in queue order. On top of that, capped runs - sqpoll
processing IORING_TW_CAP_ENTRIES_VALUE entries at a time - need the
claimed-but-unprocessed leftovers carried in a separate retry_list,
as they can't be pushed back to the shared list.
Switch tctx->task_list to a mpscq, like what was done for the
DEFER_TASKRUN paths as well.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The local (DEFER_TASKRUN) task_work list is an llist, which is LIFO
ordered, and hence __io_run_local_work() has to restore the right
running order with an O(n) llist_reverse_order() pass first. On top of
that, a batch that gets capped by max_events needs the leftover entries
parked on a separate ->retry_llist, as they can't be pushed back to the
shared list.
Switch it to the FIFO mpscq. Adds are wait-free instead of a cmpxchg
retry loop, entries are popped in queue order with no reversal pass,
capping a run simply leaves the remainder on the queue, and
->retry_llist goes away entirely. The consumer cursor, ->work_head,
lives with the rest of the ->uring_lock protected state rather than
next to the queue, so that popping entries doesn't dirty the producer
side cacheline.
For low amounts of task_work, this ends up being a bit more efficient
than the existing scheme. As an example of that, doing multishot
receives for 8 clients has the following task_work overhead:
1.02% sock-test [kernel.kallsyms] [k] io_req_local_work_add
0.88% sock-test [kernel.kallsyms] [k] __io_run_local_work_loop
0.60% sock-test [kernel.kallsyms] [k] llist_reverse_order
0.14% sock-test [kernel.kallsyms] [k] __io_run_local_work
2.64% at ~46Gb/sec
and after this change:
1.08% sock-test [kernel.kallsyms] [k] io_req_local_work_add
1.03% sock-test [kernel.kallsyms] [k] __io_run_local_work
2.11% at ~53Gb/sec
which has less overhead even though that test run was faster. For a case
of having 1024 clients on a single ring:
2.22% sock-test [kernel.kallsyms] [k] llist_reverse_order
0.84% sock-test [kernel.kallsyms] [k] __io_run_local_work_loop
0.42% sock-test [kernel.kallsyms] [k] io_req_local_work_add
0.02% sock-test [kernel.kallsyms] [k] __io_run_local_work
3.50% at ~24Gb/sec
we start to see the llist reversing taking a considerable amount of
time, and the total add+run task_work overhead is around 3.5%. After
the change:
0.90% sock-test [kernel.kallsyms] [k] __io_run_local_work
0.42% sock-test [kernel.kallsyms] [k] io_req_local_work_add
1.32% at ~26Gb/sec
most of that overhead is gone, and performance is better as well.
Caleb Sander Mateos <csander@purestorage.com> reports that it improves
the performance of a ublk 4kb workload by 4% [1], while testing v1 of
this patchset.
[1] https://lore.kernel.org/io-uring/CADUfDZr-MMYBaP-e+y9+xuRhuiunO2sBTUCmwZyd7AgT8sVtiQ@mail.gmail.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Local task_work is currently using llists for managing the work,
but that's a LIFO type of list. This means that running this task_work
needs to reverse the list first, to ensure fairness in running the
queued items.
Add a lockless FIFO queued, based on Dmitry Vyukov's intrusive MPSC
node-based queue algorithm, modified with an externally held consumer
cursor and conditional stub reinsertion. See comments in the header.
Producers are wait-free: a push is a single xchg() on the queue tail,
which serializes concurrent producers and defines the FIFO order, plus
a store linking the node to its predecessor. There are no cmpxchg retry
loops, and pushing is safe from any context, including hardirq.
The cost of linked list FIFO ordering is that a push publishes the node
in two steps - the xchg() makes it visible as the new tail before the
subsequent store links it into the chain that is reachable from the
head. A consumer hitting that window gets a NULL from mpscq_pop() while
mpscq_empty() reports false, and must retry later rather than treat the
queue as empty. The window is two instructions wide, but a producer can
get preempted inside it, so the consumer must not busy wait on it.
The consumer side supports a single consumer at a time, with callers
providing their own serialization. A stub node, which also defines the
empty state (tail == stub), allows the consumer to detach the final
node without racing against producer link stores: that node is only
handed out once the stub has been cmpxchg'ed back in as the tail. This
also guarantees that the previous tail returned by mpscq_push() cannot
get freed before that push has linked it, making it always valid for
comparisons.
The consumer cursor is deliberately not part of the queue struct - the
caller owns it and passes it to mpscq_pop(). This is done to separate
the consumer and producers cacheline. The cursor is written for every
popped entry, and keeping it on the same cacheline as ->tail would have
the consumer invalidating the line that producers need for every push.
Keeping it external lets the caller place it with its own consumer side
data instead.
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Not required right now, as io_req_local_work_add() already calls this
helper with the RCU read lock held. But in preparation for that not
being the case, grab it locally.
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-06-09 (idpf, ixgbe, igc)
Przemyslaw adds needed padding to idpf PTP structures to match firmware
expectations.
Larysa bypasses XPS configuration on XDP queues for ixgbe.
Khai Wen corrects offset into packet buffer when handling for frame
preemption on igc.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: skip RX timestamp header for frame preemption verification
ixgbe: do not configure xps for XDP queues
idpf: add padding to PTP virtchnl structures
====================
Link: https://patch.msgid.link/
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If the size of the packets would change during the transmission, it could
happen that some retries of packets are overlapping. In this case, precise
comparisons of sequence numbers by the receiver would be wrong. It is then
necessary to check if the start sequence number to the end sequence number
("seqno + length") would contain a new range.
If this is the case then this is enough to accept this packet. In all other
cases, the packet still has to be dropped (and not acked).
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When last_recv is updated to store the last receive sequence number, it is
assuming that nothing is modifying in parallel while:
* check for outdated packets is done
* out of order check is performed (and packets are stored in out-of-order
queue)
* the out-of-order queue was searched for closed gaps
* sequence number for next ack is calculated
Nothing of that was actually protected. It could therefore happen that the
last_recv was updated multiple times in parallel and the final sequence
number was calculated with deltas which had no connection to the sequence
number they were added to.
Lock this whole region with the same lock which was already used to protect
the unacked (out-of-order) list.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The last_recv_time field for batadv_tp_receiver tracks the jiffies value of
the most recent activity and is used to detect timeouts. These accesses are
not consistently protected by a lock, so READ_ONCE/WRITE_ONCE must be used
to prevent data races caused by compiler optimizations.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When the unacked_list is unbound, an attacker could send messages with
small lengths and appropriated seqno + gaps to force the receiver to
allocate more and more unacked_list entries. And the end either causing an
out-of-memory situation or increase the management overhead for the (large)
list that significant portions of CPU cycles are wasted in searching
through the list.
When limiting the list to a specific number, it is important to still
correctly add a new entry to the list. But if the list became larger than
the limit, the last entry of the list (with the highest seqno) must be
dropped to still allow the earlier seqnos to finish and therefore to
continue the process. Otherwise, the process might get stuck with too high
seqnos which are not handled by batadv_tp_ack_unordered().
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When an interface gets disabled, the worker is correctly disabled by
batadv_hardif_disable_interface() -> ... -> batadv_v_ogm_iface_disable().
In this process, the skb aggr_list is also freed.
But batadv_v_ogm_send_meshif() can still queue new skbs (via
batadv_v_ogm_queue_on_if()) to the aggr_list. This will only stop after all
cores can no longer find the RCU protected list of hard interfaces. These
queued skbs will never be freed or consumed by batadv_v_ogm_aggr_work.
The batadv_v_ogm_iface_disable() function must block
batadv_v_ogm_queue_on_if() to avoid leak of skbs.
Cc: stable@kernel.org
Fixes: f89255a02f ("batman-adv: BATMAN_V: introduce per hard-iface OGMv2 queues")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Packets with a TTL are using it to limit the amount of time this packet can
be forwarded. But for batadv_frag_packet, the TTL was always only reduced
but it was never evaluated. It could even underflow without any effect.
Check the TTL in batadv_frag_skb_fwd() before attempting to prepare it for
forwarding. This keeps it in sync with the not fragmented unicast packet.
Cc: stable@kernel.org
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Before batman-adv is allowed to write to an skb, it either has to have its
own copy of the skb or use skb_cow() to ensure that the data part is not
shared. But batadv_frag_skb_fwd() modifies the TTL even when it is shared.
Adding a skb_cow() right before this operation avoids this and can at the
same time prepare it for the modifications required to forward the
fragment.
Cc: stable@kernel.org
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The broadcast and multicast packets can be received at the same time by the
local system and forwarded to other nodes. Both are simply decrementing the
TTL at the beginning of the receive path - independent of chosen paths
(receive/forward). But such a modification of the data conflicts with the
hw csum. This is not a problem when the packet is directly forwarded but
can cause errors in the local receive path.
Such a problem can then trigger a "hw csum failure". The receiver path must
therefore ensure that the csum is fixed for each modification of the
payload before batadv_interface_rx() is reached.
Since all batman-adv packet types with a ttl have it as u8 at offset 2, a
helper can be used for all of them. But it is only used at the moment for
batadv_bcast_packet and batadv_mcast_packet because they are the only ones
which deliver the packet locally but unconditionally modify the TTL.
Cc: stable@kernel.org
Fixes: 3f69339068 ("batman-adv: bcast: queue per interface, if needed")
Fixes: 07afe1ba28 ("batman-adv: mcast: implement multicast packet reception and forwarding")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Before batman-adv is allowed to write to an skb, it either has to have its
own copy of the skb or used skb_cow() to ensure that the data part is not
shared.
The old implementation used a shared queue and created copies before
attempting to write to it. But with the new implementation, the broadcast
packet is already modified when it gets received. Potentially writing to
shared buffers in this process.
Adding a skb_cow() right before this operation avoids this and can at the
same time prepare it for the modifications required to rebroadcast the
packet.
Cc: stable@kernel.org
Fixes: 3f69339068 ("batman-adv: bcast: queue per interface, if needed")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The batadv_hardif_cnt() was previously checking if there is an
batadv_hard_iface->mesh_iface which is has the same mesh_iface. And since
batadv_hardif_disable_interface() was resetting the
batadv_hard_iface->mesh_iface after this check, it had to verify whether
*1* interface was still part of the mesh_iface before it started the
gateway deselection.
But after batadv_hardif_cnt() is now checking the lower interfaces of
mesh_iface and batadv_hardif_disable_interface() already removed the
interface via netdev_upper_dev_unlink() earlier in this function, the check
must now make sure that *0* interfaces can be found by batadv_hardif_cnt()
before selected gateway must be deselected. Otherwise the deselection would
already happen one batadv_hard_iface too early.
Because a 0 hardif count from batadv_hardif_cnt() is equal to an empty
list, it is possible to replace the counting with a simple list_empty().
Cc: stable@kernel.org
Fixes: 7dc284702b ("batman-adv: store hard_iface as iflink private data")
Reviewed-by: Nora Schiffer <neocturne@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
BPF_MAP_TYPE_ARENA supports direct-value pseudo loads, but unlike array
maps its map value_size is zero and the valid direct-value range is the
arena mmap size, max_entries * PAGE_SIZE.
Commit 3ac1a467e3 ("bpf: Fix off-by-one boundary validation in arena
direct-value access") fixed arena_map_direct_value_addr() to reject an
offset exactly at the end of the arena mapping. Add a regression test
that loads a BPF_PSEUDO_MAP_VALUE with off == arena_size and verifies
that the verifier rejects it with the expected offset in the log.
This is intentionally kept as a userspace raw-instruction test. I tried
expressing the same BPF_PSEUDO_MAP_VALUE + off == arena_size case in
verifier_arena.c with inline assembly. The only form that produces the
desired instruction bytes uses __imm_addr(arena), but that emits
R_BPF_64_NODYLD32, which the libbpf/bpftool link step rejects. Other
register, immediate, and memory constraints either fail in the BPF
backend or lower to a normal R_BPF_64_64 load followed by an ALU add,
which does not exercise arena_map_direct_value_addr() with the boundary
offset in the second ldimm64 slot.
A legacy test_verifier fixture can express the raw instruction directly,
but it needs arena map creation, mmap, and fixup plumbing in the legacy
runner. That is more intrusive than the small prog_tests raw-instruction
test.
Use the userspace raw-instruction test, following the existing selftests
pattern used for direct map-value pseudo loads, so insns[1].imm can be
set to arena_size precisely.
Assisted-by: ChatGPT:gpt-5.5
Signed-off-by: Woojin Ji <random6.xyz@gmail.com>
Reviewed-by: Emil Tsalapatis <emil@etsalapatis.com>
Cc: Emil Tsalapatis <emil@etsalapatis.com>
Cc: Junyoung Jang <graypanda.inzag@gmail.com>
Link: https://lore.kernel.org/r/20260612-arena-direct-value-v1-v4-1-b81b642f5277@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
raw_res_spin_unlock_irqrestore() calls raw_res_spin_unlock() and then
restores interrupts, this means preemption is enabled when interrupts
are still disabled (as part of raw_res_spin_unlock()) so this cannot
trigger an actual preemption.
This is inconsistent with other spinlock implementations
(raw_spin_unlock_irqrestore() and bpf_res_spin_unlock_irqrestore()
itself).
Adjust the macro to ensure interrupts are enabled before enabling
preemption, allowing to schedule at that point. Make the same
modification in the error path of raw_res_spin_lock_irqsave().
Fixes: 101acd2e78 ("rqspinlock: Add macros for rqspinlock usage")
Cc: stable@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de> # asm-generic
Acked-by: Waiman Long <longman@redhat.com>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Gabriele Monaco <gmonaco@redhat.com>
Link: https://lore.kernel.org/r/20260610090431.32427-1-gmonaco@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Xu Kuohai says:
====================
bpf: Fix setting retval to -EPERM for cgroup hooks not returning errno
This series fixes the issue reported by sashiko in [1]. The issue is that,
when a cgroup BPF program exits with 0, bpf_prog_run_array_cg() sets
the hook return value to -EPERM if it is not a valid errno. This is
correct for errno-based hooks, which return 0 on success and negative
errno on failure, but wrong for void and boolean LSM hooks. Boolean
LSM hooks should only return true or false, and void LSM hooks have
no return value at all.
Fix it by skipping setting -EPERM for hooks not returning errno.
[1] https://lore.kernel.org/bpf/20260605144232.95A141F00893@smtp.kernel.org/
====================
Link: https://patch.msgid.link/20260610201724.733943-1-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add test to check the return value when a BPF program exits with 0 for
a boolean and an errno LSM hook.
For each hook, two BPF programs are attached. The first program returns
0 without calling bpf_set_retval() to exercise the return value translation
logic, while the second program reads the retval via bpf_get_retval().
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20260610201724.733943-3-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When a cgroup BPF program exits with 0, bpf_prog_run_array_cg() sets
the hook return value to -EPERM if it is not a valid errno. This is
correct for errno-based hooks, which return 0 on success and negative
errno on failure, but wrong for boolean and void LSM hooks. Boolean
LSM hooks should only return true or false, and void LSM hooks have
no return value at all.
Fix it by skipping setting -EPERM for hooks not returning errno.
Fixes: 69fd337a97 ("bpf: per-cgroup lsm flavor")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20260610201724.733943-2-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A later change will make list_for_each_entry() cache the next element
before entering the loop body. for_each_fw_node() intentionally appends
newly discovered child nodes to the temporary walk list while the list is
being traversed.
Keep the loop open-coded so the next node is looked up only after
children have been appended. This preserves the current breadth-first
traversal semantics and prepares the code for the list iterator update.
Signed-off-by: Kaitao Cheng <chengkaitao@kylinos.cn>
Link: https://lore.kernel.org/r/20260609061347.93688-3-kaitao.cheng@linux.dev
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
qrtr_endpoint_post() validates an incoming packet with
if (!size || len != ALIGN(size, 4) + hdrlen)
goto err;
where size comes from the wire. On 32-bit, size_t is 32 bits and
ALIGN(size, 4) wraps to 0 for size >= 0xfffffffd, so the check
passes and skb_put_data(skb, data + hdrlen, size) writes past the
hdrlen-sized skb and oopses the kernel. 64-bit is unaffected.
This is the 32-bit residual of ad9d24c942 ("net: qrtr: fix OOB
Read in qrtr_endpoint_post"), which fixed only the 64-bit case.
Reject any size that cannot fit the buffer before the ALIGN.
Fixes: ad9d24c942 ("net: qrtr: fix OOB Read in qrtr_endpoint_post")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260611125455.2352279-1-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The max_macs devlink param is checked against the FW max value only at
param register time (driver load) and inside the validate callback
(devlink param set). The stored DRIVERINIT value persists across FW
resets and devlink reloads without any further checks against the max.
If the FW link type changes from Ethernet to IB and a FW reset happens,
the MAX cap for log_max_current_uc_list will become zero, but the
previously stored max_macs value remains and is unconditionally
programmed into the HCA caps in handle_hca_cap(). FW will then return a
syndrome during SET_HCA_CAP:
mlx5_cmd_out_err:839:(pid 3831): SET_HCA_CAP(0x109) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0x537801), err(-22)
set_hca_cap:907:(pid 3831): handle_hca_cap failed
This results in a failure to register the RDMA device.
This patch skips programming log_max_current_uc_list when the MAX
capability is 0 (in case of IB).
Fixes: 8680a60fc1 ("net/mlx5: Let user configure max_macs generic param")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20260611135230.534513-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wei Wang says:
====================
psp: Add support for dev-assoc/disassoc
The main purpose of this feature is to associate virtual devices like
veth or netkit with a real PSP device, so we could provide PSP
functionality to the application running with virtual devices.
A typical deployment that works with this feature is as follows:
Host Namespace:
psp_dev_local ←──physically linked──→ psp_dev_peer
(PSP device)
│
│ BPF on psp_dev_local ingress: bpf_redirect_peer() to nk_guest
│
nk_host / veth_host
│
│ BPF on nk_host ingress: bpf_redirect_neigh() to psp_dev_local
│
Guest Namespace (netns):
│
nk_guest / veth_guest
★ PSP application run here
Remote Namespace (_netns):
psp_dev_peer
★ PSP server application runs here
Note:
The general requirement for this feature to work:
For PSP to work correctly, the egress device at validate_xmit_skb()
time must have psp_dev matching the association's psd. Any device
stacking or traffic redirection that changes the egress device will
cause either:
1. TX validation failure (SKB_DROP_REASON_PSP_OUTPUT) - fail-safe
2. RX policy failure after tx-assoc - packets without PSP extension
are rejected by receiver expecting encrypted traffic
Here are a few examples that this feature would not work:
- Bonding with load balancing in round-robin, XOR, 802.3ad mode across
multiple PSP devices, or mixed PSP and non-PSP devices
- Bonding with active-backup mode might work without PSP migration for
failover case.
- ipvlan/macvlan in bridge mode would not work given packets are
loopbacked locally without going through the PSP device.
====================
Link: https://patch.msgid.link/20260608233118.2694144-1-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the following 3 tests:
- _psp_dev_get_check_netkit_psp_assoc: verifies dev-get output in both
host and guest namespaces, checking assoc-list, by-association flag,
and nsid values
- _dev_assoc_no_nsid: tests dev-assoc and dev-disassoc without the nsid
attribute, verifying ifindex lookup in the caller's namespace
- _psp_dev_assoc_cleanup_on_netkit_del: verifies that deleting the
associated netkit interface properly cleans up the assoc-list, using
a disposable netkit pair to avoid disturbing the shared environment
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-11-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add tests that verify PSP notifications are delivered to listeners in
associated namespaces:
- _key_rotation_notify_multi_ns_netkit: triggers key rotation and
verifies the notification is received in both main and guest namespaces
- _dev_change_notify_multi_ns_netkit: triggers dev_set and verifies the
dev_change notification is received in both namespaces
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-10-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add _assoc_check_list() test that associates nk_guest with the PSP
device and verifies the assoc-list is correctly populated.
Add _data_basic_send_netkit_psp_assoc() which tests PSP data send
through a netkit interface associated with a PSP device. The test
associates nk_guest with the PSP device, then sends PSP-encrypted
traffic from the guest namespace.
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-9-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add infrastructure to support PSP tests across network namespaces
using NetDrvContEnv with netkit pairs. This enables testing PSP device
association, where a non-PSP-capable device (e.g. netkit) in a guest
namespace is associated with a real PSP device in the host namespace,
allowing the guest to perform PSP encryption/decryption through the
host's PSP hardware.
The topology is:
Host NS: psp_dev_local <---> nk_host
| |
| | (netkit pair)
| |
Remote NS: psp_dev_peer Guest NS: nk_guest
(responder) (PSP tests)
env.py:
- nk_guest_ifindex is queried after moving the device into the guest
namespace, so tests can use it directly for dev-assoc
psp.py:
- PSP device lookup supports container environments where the PSP
device is on the physical interface, not the test interface
- Association helpers handle dev-assoc/dev-disassoc with defer-based
cleanup to prevent state leaks on test assertion failures
- main() tries NetDrvContEnv with primary_rx_redirect and falls back
to NetDrvEpEnv, so existing tests continue to work without the
container environment
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-8-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename _nk_host_ifname to nk_host_ifname in NetDrvContEnv to make it
a public attribute, matching the nk_guest_ifname rename. Tests that
access the host-side netkit interface name (e.g. for cleanup after
deleting the netkit pair) no longer trigger pylint protected-access
warnings.
Signed-off-by: Wei Wang <weibunny@fb.com>
Link: https://patch.msgid.link/20260608233118.2694144-7-weibunny.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
