[ Upstream commit a57d5a72f8 ]
The ndev->npinfo pointer in netpoll_poll_lock() is RCU-protected but is
being accessed directly for a NULL check. While no RCU read lock is held
in this context, we should still use proper RCU primitives for
consistency and correctness.
Replace the direct NULL check with rcu_access_pointer(), which is the
appropriate primitive when only checking for NULL without dereferencing
the pointer. This function provides the necessary ordering guarantees
without requiring RCU read-side protection.
Fixes: bea3348eef ("[NET]: Make NAPI polling independent of struct net_device objects.")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20241118-netpoll_rcu-v1-2-a1888dcb4a02@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86e8921df0 ]
TCPDIAG_GETSOCK and DCCPDIAG_GETSOCK diag are serialized
on sock_diag_table_mutex.
This is to make sure inet_diag module is not unloaded
while diag was ongoing.
It is time to get rid of this mutex and use RCU protection,
allowing full parallelism.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: eb02688c5c ("ipv6: release nexthop on device removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 114b4bb1cc ]
Following patch is going to use RCU instead of
sock_diag_table_mutex acquisition.
This patch is a preparation, no change of behavior yet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: eb02688c5c ("ipv6: release nexthop on device removal")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89de9921df ]
Some VFs may want to disable CRC stripping on incoming packets so create
an offload for that. The VF already sends information about configuring
its RX queues so use that structure to indicate that the CRC stripping
should be enabled or not.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: a884c304e1 ("ice: consistently use q_idx in ice_vc_cfg_qs_msg()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2473a3597 ]
__pa() is only intended to be used for linear map addresses and using
it for initial_boot_params which is in fixmap for arm64 will give an
incorrect value. Hence save the physical address when it is known at
boot time when calling early_init_dt_scan for arm64 and use it at kexec
time instead of converting the virtual address using __pa().
Note that arm64 doesn't need the FDT region reserved in the DT as the
kernel explicitly reserves the passed in FDT. Therefore, only a debug
warning is fixed with this change.
Reported-by: Breno Leitao <leitao@debian.org>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Fixes: ac10be5cdb ("arm64: Use common of_kexec_alloc_and_setup_fdt()")
Link: https://lore.kernel.org/r/20241023171426.452688-1-usamaarif642@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 183ec5f26b ]
During testing of the preceding changes, I noticed that in some cases,
current->kcsan_ctx.in_flat_atomic remained true until task exit. This is
obviously wrong, because _all_ accesses for the given task will be
treated as atomic, resulting in false negatives i.e. missed data races.
Debugging led to fs/dcache.c, where we can see this usage of seqlock:
struct dentry *d_lookup(const struct dentry *parent, const struct qstr *name)
{
struct dentry *dentry;
unsigned seq;
do {
seq = read_seqbegin(&rename_lock);
dentry = __d_lookup(parent, name);
if (dentry)
break;
} while (read_seqretry(&rename_lock, seq));
[...]
As can be seen, read_seqretry() is never called if dentry != NULL;
consequently, current->kcsan_ctx.in_flat_atomic will never be reset to
false by read_seqretry().
Give up on the wrong assumption of "assume closing read_seqretry()", and
rely on the already-present annotations in read_seqcount_begin/retry().
Fixes: 88ecd153be ("seqlock, kcsan: Add annotations for KCSAN")
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20241104161910.780003-6-elver@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c1806c41c ]
While fuzzing an arm64 kernel, Alexander Potapenko reported:
| BUG: KCSAN: data-race in ktime_get_mono_fast_ns / timekeeping_update
|
| write to 0xffffffc082e74248 of 56 bytes by interrupt on cpu 0:
| update_fast_timekeeper kernel/time/timekeeping.c:430 [inline]
| timekeeping_update+0x1d8/0x2d8 kernel/time/timekeeping.c:768
| timekeeping_advance+0x9e8/0xb78 kernel/time/timekeeping.c:2344
| update_wall_time+0x18/0x38 kernel/time/timekeeping.c:2360
| [...]
|
| read to 0xffffffc082e74258 of 8 bytes by task 5260 on cpu 1:
| __ktime_get_fast_ns kernel/time/timekeeping.c:372 [inline]
| ktime_get_mono_fast_ns+0x88/0x174 kernel/time/timekeeping.c:489
| init_srcu_struct_fields+0x40c/0x530 kernel/rcu/srcutree.c:263
| init_srcu_struct+0x14/0x20 kernel/rcu/srcutree.c:311
| [...]
|
| value changed: 0x000002f875d33266 -> 0x000002f877416866
|
| Reported by Kernel Concurrency Sanitizer on:
| CPU: 1 UID: 0 PID: 5260 Comm: syz.2.7483 Not tainted 6.12.0-rc3-dirty #78
This is a false positive data race between a seqcount latch writer and a reader
accessing stale data. Since its introduction, KCSAN has never understood the
seqcount_latch interface (due to being unannotated).
Unlike the regular seqlock interface, the seqcount_latch interface for latch
writers never has had a well-defined critical section, making it difficult to
teach tooling where the critical section starts and ends.
Introduce an instrumentable (non-raw) seqcount_latch interface, with
which we can clearly denote writer critical sections. This both helps
readability and tooling like KCSAN to understand when the writer is done
updating all latch copies.
Fixes: 88ecd153be ("seqlock, kcsan: Add annotations for KCSAN")
Reported-by: Alexander Potapenko <glider@google.com>
Co-developed-by: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Signed-off-by: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20241104161910.780003-4-elver@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92b043fd99 ]
The details about the handling of the "normal" values were moved
to the _msecs_to_jiffies() helpers in commit ca42aaf0c8 ("time:
Refactor msecs_to_jiffies"). However, the same commit still mentioned
__msecs_to_jiffies() in the added documentation.
Thus point to _msecs_to_jiffies() instead.
Fixes: ca42aaf0c8 ("time: Refactor msecs_to_jiffies")
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241025110141.157205-2-ojeda@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c418ba6bac ]
If an error indicating that the device needs to be reset is reported,
disable the error reporting before device reset is complete,
enable the error reporting after the reset is complete to prevent
the same error from being reported repeatedly.
Fixes: eaebf4c3b1 ("crypto: hisilicon - Unify hardware error init/uninit into QM")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41f6f64e69 ]
Use instruction (jump) history to record instructions that performed
register spill/fill to/from stack, regardless if this was done through
read-only r10 register, or any other register after copying r10 into it
*and* potentially adjusting offset.
To make this work reliably, we push extra per-instruction flags into
instruction history, encoding stack slot index (spi) and stack frame
number in extra 10 bit flags we take away from prev_idx in instruction
history. We don't touch idx field for maximum performance, as it's
checked most frequently during backtracking.
This change removes basically the last remaining practical limitation of
precision backtracking logic in BPF verifier. It fixes known
deficiencies, but also opens up new opportunities to reduce number of
verified states, explored in the subsequent patches.
There are only three differences in selftests' BPF object files
according to veristat, all in the positive direction (less states).
File Program Insns (A) Insns (B) Insns (DIFF) States (A) States (B) States (DIFF)
-------------------------------------- ------------- --------- --------- ------------- ---------- ---------- -------------
test_cls_redirect_dynptr.bpf.linked3.o cls_redirect 2987 2864 -123 (-4.12%) 240 231 -9 (-3.75%)
xdp_synproxy_kern.bpf.linked3.o syncookie_tc 82848 82661 -187 (-0.23%) 5107 5073 -34 (-0.67%)
xdp_synproxy_kern.bpf.linked3.o syncookie_xdp 85116 84964 -152 (-0.18%) 5162 5130 -32 (-0.62%)
Note, I avoided renaming jmp_history to more generic insn_hist to
minimize number of lines changed and potential merge conflicts between
bpf and bpf-next trees.
Notice also cur_hist_entry pointer reset to NULL at the beginning of
instruction verification loop. This pointer avoids the problem of
relying on last jump history entry's insn_idx to determine whether we
already have entry for current instruction or not. It can happen that we
added jump history entry because current instruction is_jmp_point(), but
also we need to add instruction flags for stack access. In this case, we
don't want to entries, so we need to reuse last added entry, if it is
present.
Relying on insn_idx comparison has the same ambiguity problem as the one
that was fixed recently in [0], so we avoid that.
[0] https://patchwork.kernel.org/project/netdevbpf/patch/20231110002638.4168352-3-andrii@kernel.org/
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Reported-by: Tao Lyu <tao.lyu@epfl.ch>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231205184248.1502704-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5baf8b037d ]
Currently MTE is permitted in two circumstances (desiring to use MTE
having been specified by the VM_MTE flag) - where MAP_ANONYMOUS is
specified, as checked by arch_calc_vm_flag_bits() and actualised by
setting the VM_MTE_ALLOWED flag, or if the file backing the mapping is
shmem, in which case we set VM_MTE_ALLOWED in shmem_mmap() when the mmap
hook is activated in mmap_region().
The function that checks that, if VM_MTE is set, VM_MTE_ALLOWED is also
set is the arm64 implementation of arch_validate_flags().
Unfortunately, we intend to refactor mmap_region() to perform this check
earlier, meaning that in the case of a shmem backing we will not have
invoked shmem_mmap() yet, causing the mapping to fail spuriously.
It is inappropriate to set this architecture-specific flag in general mm
code anyway, so a sensible resolution of this issue is to instead move the
check somewhere else.
We resolve this by setting VM_MTE_ALLOWED much earlier in do_mmap(), via
the arch_calc_vm_flag_bits() call.
This is an appropriate place to do this as we already check for the
MAP_ANONYMOUS case here, and the shmem file case is simply a variant of
the same idea - we permit RAM-backed memory.
This requires a modification to the arch_calc_vm_flag_bits() signature to
pass in a pointer to the struct file associated with the mapping, however
this is not too egregious as this is only used by two architectures anyway
- arm64 and parisc.
So this patch performs this adjustment and removes the unnecessary
assignment of VM_MTE_ALLOWED in shmem_mmap().
[akpm@linux-foundation.org: fix whitespace, per Catalin]
Link: https://lkml.kernel.org/r/ec251b20ba1964fb64cf1607d2ad80c47f3873df.1730224667.git.lorenzo.stoakes@oracle.com
Fixes: deb0f65628 ("mm/mmap: undo ->mmap() when arch_validate_flags() fails")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0fb4a7ad27 ]
Refactor the map_deny_write_exec() to not unnecessarily require a VMA
parameter but rather to accept VMA flags parameters, which allows us to
use this function early in mmap_region() in a subsequent commit.
While we're here, we refactor the function to be more readable and add
some additional documentation.
Link: https://lkml.kernel.org/r/6be8bb59cd7c68006ebb006eb9d8dc27104b1f70.1730224667.git.lorenzo.stoakes@oracle.com
Fixes: deb0f65628 ("mm/mmap: undo ->mmap() when arch_validate_flags() fails")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Jann Horn <jannh@google.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 42f994b714 ]
DAMON-based operation schemes are applied for every aggregation interval.
That was mainly because schemes were using nr_accesses, which be complete
to be used for every aggregation interval. However, the schemes are now
using nr_accesses_bp, which is updated for each sampling interval in a way
that reasonable to be used. Therefore, there is no reason to apply
schemes for each aggregation interval.
The unnecessary alignment with aggregation interval was also making some
use cases of DAMOS tricky. Quotas setting under long aggregation interval
is one such example. Suppose the aggregation interval is ten seconds, and
there is a scheme having CPU quota 100ms per 1s. The scheme will actually
uses 100ms per ten seconds, since it cannobe be applied before next
aggregation interval. The feature is working as intended, but the results
might not that intuitive for some users. This could be fixed by updating
the quota to 1s per 10s. But, in the case, the CPU usage of DAMOS could
look like spikes, and would actually make a bad effect to other
CPU-sensitive workloads.
Implement a dedicated timing interval for each DAMON-based operation
scheme, namely apply_interval. The interval will be sampling interval
aligned, and each scheme will be applied for its apply_interval. The
interval is set to 0 by default, and it means the scheme should use the
aggregation interval instead. This avoids old users getting any
behavioral difference.
Link: https://lkml.kernel.org/r/20230916020945.47296-5-sj@kernel.org
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 3488af0970 ("mm/damon/core: handle zero {aggregation,ops_update} intervals")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb94b7bb10 ]
copy_safe_from_sockptr()
return copy_from_sockptr()
return copy_from_sockptr_offset()
return copy_from_user()
copy_from_user() does not return an error on fault. Instead, it returns a
number of bytes that were not copied. Have it handled.
Patch has a side effect: it un-breaks garbage input handling of
nfc_llcp_setsockopt() and mISDN's data_sock_setsockopt().
Fixes: 6309863b31 ("net: add copy_safe_from_sockptr() helper")
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Link: https://patch.msgid.link/20241111-sockptr-copy-ret-fix-v1-1-a520083a93fb@rbox.co
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9e05e5c7ee upstream.
Prior to commit d646969055 ("Reimplement RLIMIT_SIGPENDING on top of
ucounts") UCOUNT_RLIMIT_SIGPENDING rlimit was not enforced for a class of
signals. However now it's enforced unconditionally, even if
override_rlimit is set. This behavior change caused production issues.
For example, if the limit is reached and a process receives a SIGSEGV
signal, sigqueue_alloc fails to allocate the necessary resources for the
signal delivery, preventing the signal from being delivered with siginfo.
This prevents the process from correctly identifying the fault address and
handling the error. From the user-space perspective, applications are
unaware that the limit has been reached and that the siginfo is
effectively 'corrupted'. This can lead to unpredictable behavior and
crashes, as we observed with java applications.
Fix this by passing override_rlimit into inc_rlimit_get_ucounts() and skip
the comparison to max there if override_rlimit is set. This effectively
restores the old behavior.
Link: https://lkml.kernel.org/r/20241104195419.3962584-1-roman.gushchin@linux.dev
Fixes: d646969055 ("Reimplement RLIMIT_SIGPENDING on top of ucounts")
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Co-developed-by: Andrei Vagin <avagin@google.com>
Signed-off-by: Andrei Vagin <avagin@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Alexey Gladkov <legion@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c462d5648 upstream.
SMCCCv1.3 added a hint bit which callers can set in an SMCCC function ID
(AKA "FID") to indicate that it is acceptable for the SMCCC
implementation to discard SVE and/or SME state over a specific SMCCC
call. The kernel support for using this hint is broken and SMCCC calls
may clobber the SVE and/or SME state of arbitrary tasks, though FPSIMD
state is unaffected.
The kernel support is intended to use the hint when there is no SVE or
SME state to save, and to do this it checks whether TIF_FOREIGN_FPSTATE
is set or TIF_SVE is clear in assembly code:
| ldr <flags>, [<current_task>, #TSK_TI_FLAGS]
| tbnz <flags>, #TIF_FOREIGN_FPSTATE, 1f // Any live FP state?
| tbnz <flags>, #TIF_SVE, 2f // Does that state include SVE?
|
| 1: orr <fid>, <fid>, ARM_SMCCC_1_3_SVE_HINT
| 2:
| << SMCCC call using FID >>
This is not safe as-is:
(1) SMCCC calls can be made in a preemptible context and preemption can
result in TIF_FOREIGN_FPSTATE being set or cleared at arbitrary
points in time. Thus checking for TIF_FOREIGN_FPSTATE provides no
guarantee.
(2) TIF_FOREIGN_FPSTATE only indicates that the live FP/SVE/SME state in
the CPU does not belong to the current task, and does not indicate
that clobbering this state is acceptable.
When the live CPU state is clobbered it is necessary to update
fpsimd_last_state.st to ensure that a subsequent context switch will
reload FP/SVE/SME state from memory rather than consuming the
clobbered state. This and the SMCCC call itself must happen in a
critical section with preemption disabled to avoid races.
(3) Live SVE/SME state can exist with TIF_SVE clear (e.g. with only
TIF_SME set), and checking TIF_SVE alone is insufficient.
Remove the broken support for the SMCCCv1.3 SVE saving hint. This is
effectively a revert of commits:
* cfa7ff959a ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
* a7c3acca53 ("arm64: smccc: Save lr before calling __arm_smccc_sve_check()")
... leaving behind the ARM_SMCCC_VERSION_1_3 and ARM_SMCCC_1_3_SVE_HINT
definitions, since these are simply definitions from the SMCCC
specification, and the latter is used in KVM via ARM_SMCCC_CALL_HINTS.
If we want to bring this back in future, we'll probably want to handle
this logic in C where we can use all the usual FPSIMD/SVE/SME helper
functions, and that'll likely require some rework of the SMCCC code
and/or its callers.
Fixes: cfa7ff959a ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20241106160448.2712997-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5413156ba ]
When cloning a new thread, its posix_cputimers are not inherited, and
are cleared by posix_cputimers_init(). However, this does not clear the
tick dependency it creates in tsk->tick_dep_mask, and the handler does
not reach the code to clear the dependency if there were no timers to
begin with.
Thus if a thread has a cputimer running before clone/fork, all
descendants will prevent nohz_full unless they create a cputimer of
their own.
Fix this by entirely clearing the tick_dep_mask in copy_process().
(There is currently no inherited state that needs a tick dependency)
Process-wide timers do not have this problem because fork does not copy
signal_struct as a baseline, it creates one from scratch.
Fixes: b78783000d ("posix-cpu-timers: Migrate to use new tick dependency mask model")
Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/xm26o737bq8o.fsf@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 963756aac1 upstream.
Patch series "mm: don't install PMD mappings when THPs are disabled by the
hw/process/vma".
During testing, it was found that we can get PMD mappings in processes
where THP (and more precisely, PMD mappings) are supposed to be disabled.
While it works as expected for anon+shmem, the pagecache is the
problematic bit.
For s390 KVM this currently means that a VM backed by a file located on
filesystem with large folio support can crash when KVM tries accessing the
problematic page, because the readahead logic might decide to use a
PMD-sized THP and faulting it into the page tables will install a PMD
mapping, something that s390 KVM cannot tolerate.
This might also be a problem with HW that does not support PMD mappings,
but I did not try reproducing it.
Fix it by respecting the ways to disable THPs when deciding whether we can
install a PMD mapping. khugepaged should already be taking care of not
collapsing if THPs are effectively disabled for the hw/process/vma.
This patch (of 2):
Add vma_thp_disabled() and thp_disabled_by_hw() helpers to be shared by
shmem_allowable_huge_orders() and __thp_vma_allowable_orders().
[david@redhat.com: rename to vma_thp_disabled(), split out thp_disabled_by_hw() ]
Link: https://lkml.kernel.org/r/20241011102445.934409-2-david@redhat.com
Fixes: 793917d997 ("mm/readahead: Add large folio readahead")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Leo Fu <bfu@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Cc: Boqiao Fu <bfu@redhat.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Janosch Frank <frankja@linux.ibm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7424fc6b86 ]
Currently ARM64 extracts which specific sanitizer has caused a trap via
encoded data in the trap instruction. Clang on x86 currently encodes the
same data in the UD1 instruction but x86 handle_bug() and
is_valid_bugaddr() currently only look at UD2.
Bring x86 to parity with ARM64, similar to commit 25b84002af ("arm64:
Support Clang UBSAN trap codes for better reporting"). See the llvm
links for information about the code generation.
Enable the reporting of UBSAN sanitizer details on x86 compiled with clang
when CONFIG_UBSAN_TRAP=y by analysing UD1 and retrieving the type immediate
which is encoded by the compiler after the UD1.
[ tglx: Simplified it by moving the printk() into handle_bug() ]
Signed-off-by: Gatlin Newhouse <gatlin.newhouse@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/all/20240724000206.451425-1-gatlin.newhouse@gmail.com
Link: c5978f42ec (diff-bb68d7cd88)
Link: https://github.com/llvm/llvm-project/blob/main/llvm/lib/Target/X86/X86InstrSystem.td#L27
Stable-dep-of: 1db272864f ("x86/traps: move kmsan check after instrumentation_begin")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 101c268bd2 upstream.
In support of investigating an initialization failure report [1],
cxl_test was updated to register mock memory-devices after the mock
root-port/bus device had been registered. That led to cxl_test crashing
with a use-after-free bug with the following signature:
cxl_port_attach_region: cxl region3: cxl_host_bridge.0:port3 decoder3.0 add: mem0:decoder7.0 @ 0 next: cxl_switch_uport.0 nr_eps: 1 nr_targets: 1
cxl_port_attach_region: cxl region3: cxl_host_bridge.0:port3 decoder3.0 add: mem4:decoder14.0 @ 1 next: cxl_switch_uport.0 nr_eps: 2 nr_targets: 1
cxl_port_setup_targets: cxl region3: cxl_switch_uport.0:port6 target[0] = cxl_switch_dport.0 for mem0:decoder7.0 @ 0
1) cxl_port_setup_targets: cxl region3: cxl_switch_uport.0:port6 target[1] = cxl_switch_dport.4 for mem4:decoder14.0 @ 1
[..]
cxld_unregister: cxl decoder14.0:
cxl_region_decode_reset: cxl_region region3:
mock_decoder_reset: cxl_port port3: decoder3.0 reset
2) mock_decoder_reset: cxl_port port3: decoder3.0: out of order reset, expected decoder3.1
cxl_endpoint_decoder_release: cxl decoder14.0:
[..]
cxld_unregister: cxl decoder7.0:
3) cxl_region_decode_reset: cxl_region region3:
Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6bc3: 0000 [#1] PREEMPT SMP PTI
[..]
RIP: 0010:to_cxl_port+0x8/0x60 [cxl_core]
[..]
Call Trace:
<TASK>
cxl_region_decode_reset+0x69/0x190 [cxl_core]
cxl_region_detach+0xe8/0x210 [cxl_core]
cxl_decoder_kill_region+0x27/0x40 [cxl_core]
cxld_unregister+0x5d/0x60 [cxl_core]
At 1) a region has been established with 2 endpoint decoders (7.0 and
14.0). Those endpoints share a common switch-decoder in the topology
(3.0). At teardown, 2), decoder14.0 is the first to be removed and hits
the "out of order reset case" in the switch decoder. The effect though
is that region3 cleanup is aborted leaving it in-tact and
referencing decoder14.0. At 3) the second attempt to teardown region3
trips over the stale decoder14.0 object which has long since been
deleted.
The fix here is to recognize that the CXL specification places no
mandate on in-order shutdown of switch-decoders, the driver enforces
in-order allocation, and hardware enforces in-order commit. So, rather
than fail and leave objects dangling, always remove them.
In support of making cxl_region_decode_reset() always succeed,
cxl_region_invalidate_memregion() failures are turned into warnings.
Crashing the kernel is ok there since system integrity is at risk if
caches cannot be managed around physical address mutation events like
CXL region destruction.
A new device_for_each_child_reverse_from() is added to cleanup
port->commit_end after all dependent decoders have been disabled. In
other words if decoders are allocated 0->1->2 and disabled 1->2->0 then
port->commit_end only decrements from 2 after 2 has been disabled, and
it decrements all the way to zero since 1 was disabled previously.
Link: http://lore.kernel.org/20241004212504.1246-1-gourry@gourry.net [1]
Cc: stable@vger.kernel.org
Fixes: 176baefb2e ("cxl/hdm: Commit decoder state to hardware")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://patch.msgid.link/172964782781.81806.17902885593105284330.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bfe93930ea ]
Holding a mutex across synchronize_rcu_tasks() and acquiring
that same mutex in code called from do_exit() after its call to
exit_tasks_rcu_start() but before its call to exit_tasks_rcu_stop()
results in deadlock. This is by design, because tasks that are far
enough into do_exit() are no longer present on the tasks list, making
it a bit difficult for RCU Tasks to find them, let alone wait on them
to do a voluntary context switch. However, such deadlocks are becoming
more frequent. In addition, lockdep currently does not detect such
deadlocks and they can be difficult to reproduce.
In addition, if a task voluntarily context switches during that time
(for example, if it blocks acquiring a mutex), then this task is in an
RCU Tasks quiescent state. And with some adjustments, RCU Tasks could
just as well take advantage of that fact.
This commit therefore adds the data structures that will be needed
to rely on these quiescent states and to eliminate these deadlocks.
Link: https://lore.kernel.org/all/20240118021842.290665-1-chenzhongjin@huawei.com/
Reported-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reported-by: Yang Jihong <yangjihong1@huawei.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Yang Jihong <yangjihong1@huawei.com>
Tested-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Stable-dep-of: fd70e9f1d8 ("rcu-tasks: Fix access non-existent percpu rtpcp variable in rcu_tasks_need_gpcb()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6db388585e ]
iomap_want_unshare_iter currently sits in fs/iomap/buffered-io.c, which
depends on CONFIG_BLOCK. It is also in used in fs/dax.c whіch has no
such dependency. Given that it is a trivial check turn it into an inline
in include/linux/iomap.h to fix the DAX && !BLOCK build.
Fixes: 6ef6a0e821 ("iomap: share iomap_unshare_iter predicate code with fsdax")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241015041350.118403-1-hch@lst.de
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ef6a0e821 ]
The predicate code that iomap_unshare_iter uses to decide if it's really
needs to unshare a file range mapping should be shared with the fsdax
version, because right now they're opencoded and inconsistent.
Note that we simplify the predicate logic a bit -- we no longer allow
unsharing of inline data mappings, but there aren't any filesystems that
allow shared inline data currently.
This is a fix in the sense that it should have been ported to fsdax.
Fixes: b53fdb215d ("iomap: improve shared block detection in iomap_unshare_iter")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/172796813294.1131942.15762084021076932620.stgit@frogsfrogsfrogs
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Stable-dep-of: 50793801fc ("fsdax: dax_unshare_iter needs to copy entire blocks")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4649620d94 ]
Make thermal_zone_device_unregister() wait until all of the references
to the given thermal zone object have been dropped and free it before
returning.
This guarantees that when thermal_zone_device_unregister() returns,
there is no leftover activity regarding the thermal zone in question
which is required by some of its callers (for instance, modular driver
code that wants to know when it is safe to let the module go away).
Subsequently, this will allow some confusing device_is_registered()
checks to be dropped from the thermal sysfs and core code.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-and-tested-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Stable-dep-of: 827a07525c ("thermal: core: Free tzp copy along with the thermal zone")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fad274f06 ]
Add a MEM_WRITE attribute for BPF helper functions which can be used in
bpf_func_proto to annotate an argument type in order to let the verifier
know that the helper writes into the memory passed as an argument. In
the past MEM_UNINIT has been (ab)used for this function, but the latter
merely tells the verifier that the passed memory can be uninitialized.
There have been bugs with overloading the latter but aside from that
there are also cases where the passed memory is read + written which
currently cannot be expressed, see also 4b3786a6c5 ("bpf: Zero former
ARG_PTR_TO_{LONG,INT} args in case of error").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20241021152809.33343-1-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 8ea607330a ("bpf: Fix overloading of MEM_UNINIT's meaning")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95ecba62e2 ]
Some workloads hit the infamous dev_watchdog() message:
"NETDEV WATCHDOG: eth0 (xxxx): transmit queue XX timed out"
It seems possible to hit this even for perfectly normal
BQL enabled drivers:
1) Assume a TX queue was idle for more than dev->watchdog_timeo
(5 seconds unless changed by the driver)
2) Assume a big packet is sent, exceeding current BQL limit.
3) Driver ndo_start_xmit() puts the packet in TX ring,
and netdev_tx_sent_queue() is called.
4) QUEUE_STATE_STACK_XOFF could be set from netdev_tx_sent_queue()
before txq->trans_start has been written.
5) txq->trans_start is written later, from netdev_start_xmit()
if (rc == NETDEV_TX_OK)
txq_trans_update(txq)
dev_watchdog() running on another cpu could read the old
txq->trans_start, and then see QUEUE_STATE_STACK_XOFF, because 5)
did not happen yet.
To solve the issue, write txq->trans_start right before one XOFF bit
is set :
- _QUEUE_STATE_DRV_XOFF from netif_tx_stop_queue()
- __QUEUE_STATE_STACK_XOFF from netdev_tx_sent_queue()
From dev_watchdog(), we have to read txq->state before txq->trans_start.
Add memory barriers to enforce correct ordering.
In the future, we could avoid writing over txq->trans_start for normal
operations, and rename this field to txq->xoff_start_time.
Fixes: bec251bc8b ("net: no longer stop all TX queues in dev_watchdog()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://patch.msgid.link/20241015194118.3951657-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b455f39d22 ]
Also remove count_memcg_page_event now that its last caller no longer uses
it and reword hpage_collapse_alloc_page() to hpage_collapse_alloc_folio().
This removes 1 call to compound_head() and helps convert khugepaged to
use folios throughout.
Link: https://lkml.kernel.org/r/20231020183331.10770-5-vishal.moola@gmail.com
Signed-off-by: Vishal Moola (Oracle) <vishal.moola@gmail.com>
Reviewed-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 37f0b47c51 ("mm: khugepaged: fix the arguments order in khugepaged_collapse_file trace point")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73ab05aa46 ]
With KASAN and PREEMPT_RT enabled, calling task_work_add() in
task_tick_mm_cid() may cause the following splat.
[ 63.696416] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
[ 63.696416] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 610, name: modprobe
[ 63.696416] preempt_count: 10001, expected: 0
[ 63.696416] RCU nest depth: 1, expected: 1
This problem is caused by the following call trace.
sched_tick() [ acquire rq->__lock ]
-> task_tick_mm_cid()
-> task_work_add()
-> __kasan_record_aux_stack()
-> kasan_save_stack()
-> stack_depot_save_flags()
-> alloc_pages_mpol_noprof()
-> __alloc_pages_noprof()
-> get_page_from_freelist()
-> rmqueue()
-> rmqueue_pcplist()
-> __rmqueue_pcplist()
-> rmqueue_bulk()
-> rt_spin_lock()
The rq lock is a raw_spinlock_t. We can't sleep while holding
it. IOW, we can't call alloc_pages() in stack_depot_save_flags().
The task_tick_mm_cid() function with its task_work_add() call was
introduced by commit 223baf9d17 ("sched: Fix performance regression
introduced by mm_cid") in v6.4 kernel.
Fortunately, there is a kasan_record_aux_stack_noalloc() variant that
calls stack_depot_save_flags() while not allowing it to allocate
new pages. To allow task_tick_mm_cid() to use task_work without
page allocation, a new TWAF_NO_ALLOC flag is added to enable calling
kasan_record_aux_stack_noalloc() instead of kasan_record_aux_stack()
if set. The task_tick_mm_cid() function is modified to add this new flag.
The possible downside is the missing stack trace in a KASAN report due
to new page allocation required when task_work_add_noallloc() is called
which should be rare.
Fixes: 223baf9d17 ("sched: Fix performance regression introduced by mm_cid")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20241010014432.194742-1-longman@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 466e4d801c ]
Adding task_work from NMI context requires the following:
- The kasan_record_aux_stack() is not NMU safe and must be avoided.
- Using TWA_RESUME is NMI safe. If the NMI occurs while the CPU is in
userland then it will continue in userland and not invoke the `work'
callback.
Add TWA_NMI_CURRENT as an additional notify mode. In this mode skip
kasan and use irq_work in hardirq-mode to for needed interrupt. Set
TIF_NOTIFY_RESUME within the irq_work callback due to k[ac]san
instrumentation in test_and_set_bit() which does not look NMI safe in
case of a report.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240704170424.1466941-3-bigeasy@linutronix.de
Stable-dep-of: 73ab05aa46 ("sched/core: Disable page allocation in task_tick_mm_cid()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3acf8ace68 ]
Add missed value to kprobe attached through perf link info to
hold the stats of missed kprobe handler execution.
The kprobe's missed counter gets incremented when kprobe handler
is not executed due to another kprobe running on the same cpu.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20230920213145.1941596-4-jolsa@kernel.org
Stable-dep-of: 4deecdd29c ("bpf: fix unpopulated name_len field in perf_event link info")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1442ee0011 upstream.
Kunkun Jiang reported that there is a small window of opportunity for
userspace to force a change of affinity for a VPE while the VPE has already
been unmapped, but the corresponding doorbell interrupt still visible in
/proc/irq/.
Plug the race by checking the value of vmapp_count, which tracks whether
the VPE is mapped ot not, and returning an error in this case.
This involves making vmapp_count common to both GICv4.1 and its v4.0
ancestor.
Fixes: 64edfaa9a2 ("irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP")
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/c182ece6-2ba0-ce4f-3404-dba7a3ab6c52@huawei.com
Link: https://lore.kernel.org/all/20241002204959.2051709-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d7b2ce43d upstream.
Fix the build warnings when CONFIG_FSL_ENETC_MDIO is not enabled.
The detailed warnings are shown as follows.
include/linux/fsl/enetc_mdio.h:62:18: warning: no previous prototype for function 'enetc_hw_alloc' [-Wmissing-prototypes]
62 | struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs)
| ^
include/linux/fsl/enetc_mdio.h:62:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
62 | struct enetc_hw *enetc_hw_alloc(struct device *dev, void __iomem *port_regs)
| ^
| static
8 warnings generated.
Fixes: 6517798dd3 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410102136.jQHZOcS4-lkp@intel.com/
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241011030103.392362-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 386520e0ec ]
Similarly to RTNL_FLAG_DOIT_UNLOCKED, this new flag
allows dump operations registered via rtnl_register()
or rtnl_register_module() to opt-out from RTNL protection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5be2062e30 ("mpls: Handle error of rtnl_register_module().")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8874e414fe ]
Add defines to get major and minor version from a TPMI version field
value. This will avoid code duplication to convert in every feature
driver. Also add define for invalid version field.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20231003184916.1860084-2-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Stable-dep-of: 1d39092397 ("powercap: intel_rapl_tpmi: Ignore minor version change")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3868ab0f19 ]
The 2023 SIGCOMM paper "Improving Network Availability with Protective
ReRoute" has indicated Linux TCP's RTO-triggered txhash rehashing can
effectively reduce application disruption during outages. To better
measure the efficacy of this feature, this patch adds three more
detailed stats during RTO recovery and exports via TCP_INFO.
Applications and monitoring systems can leverage this data to measure
the network path diversity and end-to-end repair latency during network
outages to improve their network infrastructure.
The following counters are added to tcp_sock in order to track RTO
events over the lifetime of a TCP socket.
1. u16 total_rto - Counts the total number of RTO timeouts.
2. u16 total_rto_recoveries - Counts the total number of RTO recoveries.
3. u32 total_rto_time - Counts the total time spent (ms) in RTO
recoveries. (time spent in CA_Loss and
CA_Recovery states)
To compute total_rto_time, we add a new u32 rto_stamp field to
tcp_sock. rto_stamp records the start timestamp (ms) of the last RTO
recovery (CA_Loss).
Corresponding fields are also added to the tcp_info struct.
Signed-off-by: Aananth V <aananthv@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 27c80efcc2 ("tcp: fix TFO SYN_RECV to not zero retrans_stamp with retransmits out")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59c34008d3 ]
Add new PCI device IDs into the root IDs and miscellaneous IDs lists to
provide support for the latest generation of AMD 1Ah family 60h processor
models.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Link: https://lore.kernel.org/r/20240722092801.3480266-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e640f0a47 ]
Add the new PCI Device IDs to the MISC IDs list to support new
generation of AMD 1Ah family 70h Models of processors.
[ bp: Massage commit message. ]
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240510111829.969501-1-Shyam-sundar.S-k@amd.com
Stable-dep-of: 59c34008d3 ("x86/amd_nb: Add new PCI IDs for AMD family 1Ah model 60h")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9246b487ab ]
Add DMA support for audio function of Glenfly Arise chip, which uses
Requester ID of function 0.
Link: https://lore.kernel.org/r/CA2BBD087345B6D1+20240823095708.3237375-1-wangyuli@uniontech.com
Signed-off-by: SiyuLi <siyuli@glenfly.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
[bhelgaas: lower-case hex to match local code, drop unused Device IDs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28ead3eaab ]
bpf progs can be attached to kernel functions, and the attached functions
can take different parameters or return different return values. If
prog attached to one kernel function tail calls prog attached to another
kernel function, the ctx access or return value verification could be
bypassed.
For example, if prog1 is attached to func1 which takes only 1 parameter
and prog2 is attached to func2 which takes two parameters. Since verifier
assumes the bpf ctx passed to prog2 is constructed based on func2's
prototype, verifier allows prog2 to access the second parameter from
the bpf ctx passed to it. The problem is that verifier does not prevent
prog1 from passing its bpf ctx to prog2 via tail call. In this case,
the bpf ctx passed to prog2 is constructed from func1 instead of func2,
that is, the assumption for ctx access verification is bypassed.
Another example, if BPF LSM prog1 is attached to hook file_alloc_security,
and BPF LSM prog2 is attached to hook bpf_lsm_audit_rule_known. Verifier
knows the return value rules for these two hooks, e.g. it is legal for
bpf_lsm_audit_rule_known to return positive number 1, and it is illegal
for file_alloc_security to return positive number. So verifier allows
prog2 to return positive number 1, but does not allow prog1 to return
positive number. The problem is that verifier does not prevent prog1
from calling prog2 via tail call. In this case, prog2's return value 1
will be used as the return value for prog1's hook file_alloc_security.
That is, the return value rule is bypassed.
This patch adds restriction for tail call to prevent such bypasses.
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20240719110059.797546-4-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e8fb2eda9 ]
Use the correct struct member name in the kernel-doc notation
to prevent a kernel-doc build warning.
include/linux/jbd2.h:1303: warning: Function parameter or struct member 'j_transaction_overhead_buffers' not described in 'journal_s'
include/linux/jbd2.h:1303: warning: Excess struct member 'j_transaction_overhead' description in 'journal_s'
Fixes: e3a00a2378 ("jbd2: precompute number of transaction descriptor blocks")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/20240710182252.4c281445@canb.auug.org.au/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20240723051647.3053491-1-rdunlap@infradead.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee08acb58f ]
In order to optimize the data transfer, let's use the async DMA operation
for writing (queuing) data to the host.
In the async path, the completion event for the transfer ring will only be
sent to the host when the controller driver notifies the MHI stack of the
actual transfer completion using the callback (mhi_ep_skb_completion)
supplied in "struct mhi_ep_buf_info".
Also to accommodate the async operation, the transfer ring read offset
(ring->rd_offset) is cached in the "struct mhi_ep_chan" and updated locally
to let the stack queue further ring items to the controller driver. But the
actual read offset of the transfer ring will only be updated in the
completion callback.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: c7d0b2db5b ("bus: mhi: ep: Do not allocate memory for MHI objects from DMA zone")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b786ed8fb ]
These callbacks can be implemented by the controller drivers to perform
async read/write operation that increases the throughput.
For aiding the async operation, a completion callback is also introduced.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: c7d0b2db5b ("bus: mhi: ep: Do not allocate memory for MHI objects from DMA zone")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 927105244f ]
In the preparation for adding async API support, let's rename the existing
APIs to read_sync() and write_sync() to make it explicit that these APIs
are used for synchronous read/write.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Stable-dep-of: c7d0b2db5b ("bus: mhi: ep: Do not allocate memory for MHI objects from DMA zone")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 372c669271 ]
This reverts commit 41efa43124.
IMS (Interrupt Message Store) support appeared in v6.2, but there are no
users yet.
Remove it for now. We can add it back when a user comes along. If this is
re-added later, this could be squashed with these commits:
0194425af0 ("PCI/MSI: Provide IMS (Interrupt Message Store) support")
c9e5bea273 ("PCI/MSI: Provide pci_ims_alloc/free_irq()")
which added the non-stub implementations.
Link: https://lore.kernel.org/r/20240410221307.2162676-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3cefaf65 ]
Krzysztof reported an issue [0] which is caused by parallel attempts to
instantiate the same I2C client device. This can happen if driver
supports auto-detection, but certain devices are also instantiated
explicitly.
The original change isn't actually wrong, it just revealed that I2C core
isn't prepared yet to handle this scenario.
Calls to i2c_new_client_device() can be nested, therefore we can't use a
simple mutex here. Parallel instantiation of devices at different addresses
is ok, so we just have to prevent parallel instantiation at the same address.
We can use a bitmap with one bit per 7-bit I2C client address, and atomic
bit operations to set/check/clear bits.
Now a parallel attempt to instantiate a device at the same address will
result in -EBUSY being returned, avoiding the "sysfs: cannot create duplicate
filename" splash.
Note: This patch version includes small cosmetic changes to the Tested-by
version, only functional change is that address locking is supported
for slave addresses too.
[0] https://lore.kernel.org/linux-i2c/9479fe4e-eb0c-407e-84c0-bd60c15baf74@ans.pl/T/#m12706546e8e2414d8f1a0dc61c53393f731685cc
Fixes: caba40ec35 ("eeprom: at24: Probe for DDR3 thermal sensor in the SPD case")
Cc: stable@vger.kernel.org
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73febd775b ]
Two drivers already implement custom debugfs handling for their
i2c_adapter and more will come. So, let the core create a debugfs
directory per adapter and pass that to drivers for their debugfs files.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Stable-dep-of: 8d3cefaf65 ("i2c: core: Lock address during client device instantiation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 678379e1d4 upstream.
Cloning a descriptor table picks the size that would cover all currently
opened files. That's fine for clone() and unshare(), but for close_range()
there's an additional twist - we clone before we close, and it would be
a shame to have
close_range(3, ~0U, CLOSE_RANGE_UNSHARE)
leave us with a huge descriptor table when we are not going to keep
anything past stderr, just because some large file descriptor used to
be open before our call has taken it out.
Unfortunately, it had been dealt with in an inherently racy way -
sane_fdtable_size() gets a "don't copy anything past that" argument
(passed via unshare_fd() and dup_fd()), close_range() decides how much
should be trimmed and passes that to unshare_fd().
The problem is, a range that used to extend to the end of descriptor
table back when close_range() had looked at it might very well have stuff
grown after it by the time dup_fd() has allocated a new files_struct
and started to figure out the capacity of fdtable to be attached to that.
That leads to interesting pathological cases; at the very least it's a
QoI issue, since unshare(CLONE_FILES) is atomic in a sense that it takes
a snapshot of descriptor table one might have observed at some point.
Since CLOSE_RANGE_UNSHARE close_range() is supposed to be a combination
of unshare(CLONE_FILES) with plain close_range(), ending up with a
weird state that would never occur with unshare(2) is confusing, to put
it mildly.
It's not hard to get rid of - all it takes is passing both ends of the
range down to sane_fdtable_size(). There we are under ->files_lock,
so the race is trivially avoided.
So we do the following:
* switch close_files() from calling unshare_fd() to calling
dup_fd().
* undo the calling convention change done to unshare_fd() in
60997c3d45 "close_range: add CLOSE_RANGE_UNSHARE"
* introduce struct fd_range, pass a pointer to that to dup_fd()
and sane_fdtable_size() instead of "trim everything past that point"
they are currently getting. NULL means "we are not going to be punching
any holes"; NR_OPEN_MAX is gone.
* make sane_fdtable_size() use find_last_bit() instead of
open-coding it; it's easier to follow that way.
* while we are at it, have dup_fd() report errors by returning
ERR_PTR(), no need to use a separate int *errorp argument.
Fixes: 60997c3d45 "close_range: add CLOSE_RANGE_UNSHARE"
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
