There is no Rohm DAC on the CycloneV devkit according to the online
documentation for it that I could find, and it definitely does not have
a dh2228fv as this device does not actually exist! Remove the DAC node
from the devicetree as it is not acceptable to pretend to have a device
on a board in order to bind the spidev driver in Linux.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240717-partake-antivirus-3347e415fb7d@spud
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
When the serial console is enabled, we need to disable power delivery
since serial uses the SBU1/2 pins and appears to confuse the TCPCI,
resulting in endless interrupts.
For now, change the DT such that the serial console continues working.
Note1: We can not have both typec-power-opmode and
new-source-frs-typec-current active at the same time, as otherwise DT
binding checks complain.
Note2: When using a downstream DT, the Pixel boot-loader will modify
the DT accordingly before boot, but for this upstream DT it doesn't
know where to find the TCPCI node. The intention is for this commit to
be reverted once an updated Pixel boot-loader becomes available.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241203-gs101-phy-lanes-orientation-dts-v2-5-1412783a6b01@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
On Pixel 6 (and Pro), a max77759 companion PMIC for USB Type-C
applications is used, which contains four functional blocks (at
distinct I2C addresses):
* top (including GPIO)
* charger
* fuel gauge
* TCPCi
While in the same package, TCPCi and Fuel Gauge have separate I2C
addresses, interrupt lines and interrupt status registers and can be
treated independently.
The TCPCi is required to detect and handle connector orientation in
Pixel's USB PHY driver, and to configure the USB controller's role
(host vs device).
This change adds the TCPCi part as it can be independent and doesn't
need a top-level MFD.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241203-gs101-phy-lanes-orientation-dts-v2-4-1412783a6b01@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
In CoCo VMs it is possible for the untrusted host to cause
set_memory_decrypted() to fail such that an error is returned
and the resulting memory is shared. Callers need to take care
to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional
or security issues.
Leak the decrypted memory when set_memory_decrypted() fails,
and don't need to print an error since set_memory_decrypted()
will call WARN_ONCE().
Fixes: f4738f56d1 ("virt: tdx-guest: Add Quote generation support using TSM_REPORTS")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240619111801.25630-1-lirongqing%40baidu.com
An indirect branch instruction sets the CPU indirect branch tracker
(IBT) into WAIT_FOR_ENDBRANCH (WFE) state and WFE stays asserted
across the instruction boundary. When the decoder finds an
inappropriate instruction while WFE is set ENDBR, the CPU raises a #CP
fault.
For the "kernel IBT no ENDBR" selftest where #CPs are deliberately
triggered, the WFE state of the interrupted context needs to be
cleared to let execution continue. Otherwise when the CPU resumes
from the instruction that just caused the previous #CP, another
missing-ENDBRANCH #CP is raised and the CPU enters a dead loop.
This is not a problem with IDT because it doesn't preserve WFE and
IRET doesn't set WFE. But FRED provides space on the entry stack
(in an expanded CS area) to save and restore the WFE state, thus the
WFE state is no longer clobbered, so software must clear it.
Clear WFE to avoid dead looping in ibt_clear_fred_wfe() and the
!ibt_fatal code path when execution is allowed to continue.
Clobbering WFE in any other circumstance is a security-relevant bug.
[ dhansen: changelog rewording ]
Fixes: a5f6c2ace9 ("x86/shstk: Add user control-protection fault handler")
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241113175934.3897541-1-xin%40zytor.com
Before commit:
f5d39b0208 ("freezer,sched: Rewrite core freezer logic")
the frozen task stat was reported as 'D' in cgroup v1.
However, after rewriting the core freezer logic, the frozen task stat is
reported as 'R'. This is confusing, especially when a task with stat of
'S' is frozen.
This bug can be reproduced with these steps:
$ cd /sys/fs/cgroup/freezer/
$ mkdir test
$ sleep 1000 &
[1] 739 // task whose stat is 'S'
$ echo 739 > test/cgroup.procs
$ echo FROZEN > test/freezer.state
$ ps -aux | grep 739
root 739 0.1 0.0 8376 1812 pts/0 R 10:56 0:00 sleep 1000
As shown above, a task whose stat is 'S' was changed to 'R' when it was
frozen.
To solve this regression, simply maintain the same reported state as
before the rewrite.
[ mingo: Enhanced the changelog and comments ]
Fixes: f5d39b0208 ("freezer,sched: Rewrite core freezer logic")
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Koutný <mkoutny@suse.com>
Link: https://lore.kernel.org/r/20241217004818.3200515-1-chenridong@huaweicloud.com
Fix the following objtool warning during build time:
fs/bcachefs/btree_trans_commit.o: warning: objtool: bch2_trans_commit_write_locked.isra.0() falls through to next function do_bch2_trans_commit.isra.0()
fs/bcachefs/btree_trans_commit.o: warning: objtool: .text: unexpected end of section
......
fs/bcachefs/btree_update.o: warning: objtool: bch2_trans_update_get_key_cache() falls through to next function flush_new_cached_update()
fs/bcachefs/btree_update.o: warning: objtool: flush_new_cached_update() falls through to next function bch2_trans_update_by_path()
bch2_trans_unlocked_error() is an Obviously Correct (tm) panic() wrapper,
add it to the list of known noreturns.
[ mingo: Improved the changelog ]
Fixes: fd104e2967 ("bcachefs: bch2_trans_verify_not_unlocked()")
Signed-off-by: chenchangcheng <chenchangcheng@kylinos.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20241220074847.3418134-1-ccc194101@163.com
The io-wq path can downgrade a multishot request to oneshot mode,
however io_read_mshot() doesn't handle that and would still post
multiple CQEs. That's not allowed, because io_req_post_cqe() requires
stricter context requirements.
The described can only happen with pollable files that don't support
FMODE_NOWAIT, which is an odd combination, so if even allowed it should
be fairly rare.
Cc: stable@vger.kernel.org
Reported-by: chase xd <sl1589472800@gmail.com>
Fixes: bee1d5becd ("io_uring: disable io-wq execution of multishot NOWAIT requests")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/c5c8c4a50a882fd581257b81bf52eee260ac29fd.1735407848.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=y/jk
-----END PGP SIGNATURE-----
Merge tag '6.13-rc4-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- fix caching of files that will be reused for write
- minor cleanup
* tag '6.13-rc4-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Remove unused is_server_using_iface()
smb: enable reuse of deferred file handles for write operations
The configuration and ID registers are not volatile and are not affected
by read operations (i.e. not precious), making them suitable to be
cached in order to reduce the number of accesses to the device.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241224-veml3235_scale-v2-3-2e1286846c77@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the latest binutils, modpost fails with a bus error on some
architectures such as ARM and sparc64.
Since binutils commit 1f1b5e506bf0 ("bfd/ELF: restrict file alignment
for object files"), the byte offset to each section (sh_offset) in
relocatable ELF is no longer guaranteed to be aligned.
modpost parses MODULE_DEVICE_TABLE() data structures, which are usually
located in the .rodata section. If it is not properly aligned, unaligned
access errors may occur.
To address the issue, this commit imports the get_unaligned() helper
from include/linux/unaligned.h.
The get_unaligned_native() helper caters to the endianness in addition
to handling the unaligned access.
I slightly refactored do_pcmcia_entry() and do_input() to avoid writing
back to an unaligned address. (We would need the put_unaligned() helper
to do that.)
The addend_*_rel() functions need similar adjustments because the .text
sections are not aligned either.
It seems that the .symtab, .rel.* and .rela.* sections are still aligned.
Keep normal pointer access for these sections to avoid unnecessary
performance costs.
Reported-by: Paulo Pisati <paolo.pisati@canonical.com>
Reported-by: Matthias Klose <doko@debian.org>
Closes: https://sourceware.org/bugzilla/show_bug.cgi?id=32435
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Closes: https://sourceware.org/bugzilla/show_bug.cgi?id=32493
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Optimize the size of guid_name[], as it only requires 1 additional byte
for '\0' instead of 2.
Simplify the loop by incrementing the iterator by 1 instead of 2.
Remove the unnecessary TO_NATIVE() call, as the guid is represented as
a byte stream.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
This loop should iterate over the range from 'min' to 'max' inclusively.
The last interation is missed.
Fixes: 1d8f430c15 ("[PATCH] Input: add modalias support")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Add interrupt-names INT1 and INT2 for the two interrupt lines of the
sensor.
When one of the two interrupt lines is connected, the interrupt as its
interrupt-name, need to be declared in the devicetree. The driver then
configures the sensor to indicate its events on either INT1 or INT2.
If no interrupt is configured, then no interrupt-name should be
configured, and vice versa. In this case the sensor runs in FIFO BYPASS
mode. This allows sensor measurements, but none of the sensor events.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241225181338.69672-4-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove interrupts from the list of required properties. The ADXL345
does not need interrupts for basic accelerometer functionality.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20241225181338.69672-3-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simply check the max_register value to decide whether
MESON_SAR_ADC_REG11 is present on the current IP revision. This allows
dropping two additional bool fields from struct meson_sar_adc_param
which previously had to be manually kept in sync. No functional changes
intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://patch.msgid.link/20241224142941.97759-4-martin.blumenstingl@googlemail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The field should be called "vref_voltage", without a typo in the word
voltage. No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://patch.msgid.link/20241224142941.97759-2-martin.blumenstingl@googlemail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I assume this device is only used on architectures where a 8 byte
integer type is always 8 byte aligned. However, I would prefer IIO
drivers to never make that assumption as the code gets copied into
new drivers which are not so tightly couple to one driver and those
can run on architectures that align these types to only 4 bytes in which
case this structure may be 4 byte to small leading to a buffer overrun.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-21-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The vast majority of IIO drivers use aligned_s64 for the type of the
timestamp field. It is not a bug to use int64_t and until this series
iio_push_to_buffers_with_timestamp() took and int64_t timestamp, it
is inconsistent. This change is to remove that inconsistency and
ensure there is one obvious choice for future drivers.
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-19-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The vast majority of IIO drivers use aligned_s64 for the type of the
timestamp field. It is not a bug to use int64_t and until this series
iio_push_to_buffers_with_timestamp() took and int64_t timestamp, it
is inconsistent. This change is to remove that inconsistency and
ensure there is one obvious choice for future drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-18-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The vast majority of IIO drivers use aligned_s64 for the type of the
timestamp field. It is not a bug to use int64_t and until this series
iio_push_to_buffers_with_timestamp() took and int64_t timestamp, it
is inconsistent. This change is to remove that inconsistency and
ensure there is one obvious choice for future drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-17-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-15-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Acked-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-14-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-13-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-12-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-11-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-10-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Acked-By: Matti Vaittinen <mazziesaccount@gmail.com> #For bu27034, rpr0521
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-9-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-8-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Acked-By: Matti Vaittinen <mazziesaccount@gmail.com> #for the BD1390
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-7-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-6-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-5-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-4-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Whilst it doesn't actually make any difference because the code
that fills this field doesn't care, timestamps are all signed.
Use the new aligned_s64 instead of open coding alignment to avoid
confusing static analyzers and give slightly cleaner code.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-3-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Whilst it doesn't actually make any difference because the code
that fills this field doesn't care, timestamps are all signed.
Use the new aligned_s64 instead of open coding alignment to avoid
confusing static analyzers and give slightly cleaner code.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-2-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for STM32MP25 SoC. Use newly introduced compatible to handle
this new HW variant. Add TIM20 trigger definitions that can be used by
the stm32 analog-to-digital converter. Use compatible data to identify
it.
As the counter framework is now superseding the deprecated IIO counter
interface (IIO_COUNT), don't support it. Only register IIO trigger
devices for ADC usage. So, make the valids_table a cfg option.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://patch.msgid.link/20241220095927.1122782-4-fabrice.gasnier@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Configuration information is now prioritized from the firmware file.
If the firmware file is missing or fails to parse, the driver falls
back to using the default configuration list for writing the settings.
Signed-off-by: Yasin Lee <yasin.lee.x@gmail.com>
Link: https://patch.msgid.link/20241216-hx9023s-firmware-20241209-v2-1-ce1b0a1121d0@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79703 is a 6 channel digital to analog converter.
Based on the data-sheet examples the hardware would support setting the
DAC word without changing the actual output. The data-sheet is not too
specific on how the enabling the output of new voltage set by DAC
should be done - hence this is not implemented by the driver.
The BD79703 would also support two specific "PULL_DOWN" modes. These
aren't currently supported by the driver either.
Add a very basic support for controlling the channel outputs one-by-one.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/bc77d7b979ca28408a216f597082fcd94ec63be7.1734608215.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
