Improve eMMC on phyCORE-i.MX93 SOM by adding 100MHz and 200MHz pinctrl
modes. This enables to use eMMC at enhanced data rates (e.g. HS400).
While at it, apply a workaround for the i.MX93 chip errata ERR052021.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is already an external pull-down resistor on the LED output line.
It makes no sense to have both pull-down and pull-up resistors enabled
at the same time. Thus disable the internal pull-up.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the EEPROM chip available on I2C3 bus (address 0x50),
used for the PHYTEC SOM detection.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PMIC driver for PCA9451A used on phyCORE-i.MX93 SOM is available since
commit 5edeb7d312 ("regulator: pca9450: add pca9451a support"). Add
support for it in the SOM device-tree.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the file 'c3-isp.rst' that documents the c3-isp driver.
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add the file 'metafmt-c3-isp.rst' that documents
the meta format of c3-isp.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The C3 ISP supports multi-camera and multi-exposure HDR, integrates
advanced imaging technologies for optimal quality, and drives the
core pipeline to transform raw sensor data into high-fidelity images
through demosaicing, color correction, and tone mapping operations.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: drop unnecessary vb2_ops_wait_prepare/finish callbacks]
Add a header that describes the 3A statistics buffer and the
parameters buffer for C3 ISP
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
C3ISP_PARAMS is the C3 ISP Parameters format.
C3ISP_STATS is the C3 ISP Statistics format.
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
c3-isp is used to process raw image.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add a driver for the MIPI adapter unit found on the Amlogic C3 SoC.
This driver is used to align the MIPI data from the MIPI CSI-2 receiver
unit and send the aligned data to the ISP unit.
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
c3-mipi-adapter is used to organize mipi data and
send raw data to ISP module.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add a driver for the CSI-2 receiver unit found on the Amlogic C3 SoC.
Create a drivers/media/platform/amlogic/c3/ directory to host the driver
and the forthcoming support for the Amlogic C3 MIPI adapter and C3 ISP.
This driver is used to receive the MIPI data from image sensor.
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: fix typo: uinit -> unit]
c3-mipi-csi2 is used to receive mipi data from image sensor.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Keke Li <keke.li@amlogic.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Async flip is not supported with Indexed 8 bit format as it depends on
LUT and can't be updated atomically.
Note: This may change the alignment for C8 framebuffers on some
platforms.
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250407-asyn-v13-5-b93ef83076c5@intel.com
Hook up the newly added plane function pointer
format_mod_supported_async to populate the modifiers/formats supported
by asynchronous flips.
v5: Correct the if condition for modifier support check (Chaitanya)
v6: Replace uint32_t/uint64_t with u32/u64 (Jani)
v7: Move plannar check from intel_async_flip_check_hw() to
intel_plane_format_mod_supported_async() (Ville)
v8: In case of error print format/modifier (Chaitanya)
v9: Exclude C8 format as its not supported by hardware
v10: filter only planar formats
move changes in can_async_flip to new patch (Ville)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250407-asyn-v13-4-b93ef83076c5@intel.com
The function intel_plane_can_async_flip() checks for async supported
modifier, add format support check also in the same function.
Note: on ADL the surface base addr is required to be 16k aligned and if
not might generate DMAR and GGTT faults leading to glitches. This patch
changes the 16k alignment to 4k for planar formats.
v11: Move filtering Indexed 8bit to a separate patch (Ville)
v12: correct the commit msg and remove unwanted debug print (Ville)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250407-asyn-v13-3-b93ef83076c5@intel.com
create_in_formats creates the list of supported format/modifiers for
synchronous flips, modify the same function so as to take the
format_mod_supported as argument and create list of format/modifier for
async as well.
v5: create_in_formats can return -ve value in failure case, correct the
if condition to check the creation of blob <Chaitanya>
Dont add the modifier for which none of the formats is not supported.
v6: Remove the code for masking the unsupported modifiers as UMD can
leave with it. (Naveen/Chaitanya)
v7: Retain the unsupported modifiers, userspace should have no
impact, return pointer to blob instead of blob_id(Ville)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Acked-by: Xaver Hugl <xaver.hugl@kde.org>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Naveen Kumar <naveen1.kumar@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250407-asyn-v13-2-b93ef83076c5@intel.com
There exists a property IN_FORMATS which exposes the plane supported
modifiers/formats to the user. In some platforms when asynchronous flip
are used all of modifiers/formats mentioned in IN_FORMATS are not
supported. This patch adds a new plane property IN_FORMATS_ASYNC to
expose the async flip supported modifiers/formats so that user can use
this information ahead and do flip with unsupported
formats/modifiers. This will save flip failures.
Add a new function pointer similar to format_mod_supported specifically
for asynchronous flip.
v2: Remove async variable from drm_plane (Ville)
v3: Add new function pointer for async (Ville)
v5: Typo corrected in commit message & some correction in the kernel
documentation. (Chaitanya)
v7: Place IN_FORMATS_ASYNC next to IN_FORMATS (Ville)
v8: replace uint32_t with u32 and uint64_t with u64 (Chaitanya)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Acked-by: Xaver Hugl <xaver.hugl@kde.org>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Naveen Kumar <naveen1.kumar@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20250407-asyn-v13-1-b93ef83076c5@intel.com
The ov02c10 driver divides a 64-bit number but reply relies on division
operator to do that. Use div_u64() so this will compile everywhere.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The Google Dirks device used the wrong ports, fix this.
Signed-off-by: Kells Ping <kells.ping@quanta.corp-partner.google.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: fixed outdated subject and commit log]
Use common wrappers operating directly on the struct sg_table objects to
fix incorrect use of scatterlists sync calls. dma_sync_sg_for_*()
functions have to be called with the number of elements originally passed
to dma_map_sg_*() function, not the one returned in sgtable's nents.
Fixes: d33186d0be ("[media] omap3isp: ccdc: Use the DMA API for LSC")
Fixes: 0e24e90f2c ("[media] omap3isp: stat: Use the DMA API")
CC: stable@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Use common wrappers operating directly on the struct sg_table objects to
fix incorrect use of scatterlists sync calls. dma_sync_sg_for_*()
functions have to be called with the number of elements originally passed
to dma_map_sg_*() function, not the one returned in sgt->nents.
Fixes: d4db5eb57c ("media: videobuf2: add begin/end cpu_access callbacks to dma-sg")
CC: stable@vger.kernel.org
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The sequence number communicate the lost frames to userspace. For this
reason, it must be incremented even when a frame is skipped. This allows
userspace such as GStreamer to report the loss.
Fixes: 7b59b132ad ("media: platform: synopsys: Add support for HDMI input driver")
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
This variable is used to fill the v4l2_buffer.sequence, let's name it
the exact same way to reduce confusion.
No functional changes.
Fixes: 7b59b132ad ("media: platform: synopsys: Add support for HDMI input driver")
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The conditional (type == V4L2_TUNER_RADIO) always evaluates true due to the
earlier check for (type != V4L2_TUNER_RADIO) (line 2826)
CID: 1226742
Signed-off-by: Chris Green <chris.e.green@hotmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Once device_register() failed, we should call put_device() to
decrement reference count for cleanup. Or it could cause memory leak.
And move callback function v4l2_device_release() and v4l2_device_get()
before put_device().
As comment of device_register() says, 'NOTE: _Never_ directly free
@dev after calling this function, even if it returned an error! Always
use put_device() to give up the reference initialized in this function
instead.'
Found by code review.
Cc: stable@vger.kernel.org
Fixes: dc93a70cc7 ("V4L/DVB (9973): v4l2-dev: use the release callback from device instead of cdev")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
When running in nominal drive mode, the maximum allowed frequency for
the NoC is 800MHz, but the OPP table for the i.MX8MP interconnect device
listed the 1GHz operating point for the NoC, regardless of the active
mode.
The newly introduced imx8mp-nominal.dtsi header reconfigures the clock
controller to observe nominal drive mode limits, so have it modify the
maximum NoC OPP as well.
Fixes: 255fbd9eab ("arm64: dts: imx8mp: Add optional nominal drive mode DTSI")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The function efi_load_initrd() had a documentation warning due to
the missing description for the 'out' parameter. Add the parameter
description to the kernel-doc comment to resolve the warning and
improve API documentation.
Fixes the following compiler warning:
drivers/firmware/efi/libstub/efi-stub-helper.c:611: warning: Function parameter or struct member 'out' not described in 'efi_load_initrd'
Fixes: f4dc7fffa9 ("efi: libstub: unify initrd loading between architectures")
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The partial matching of DAI widget to link names, can cause problems if
one of the widget names is a substring of another. E.g. with names
"Foo1" and Foo10", it's not possible to correctly link up "Foo1".
Modify the logic so that if multiple DAI links match the widget stream
name, prioritize a full match if one is found.
Fixes: fe88788779 ("ASoC: SOF: topology: Use partial match for connecting DAI link and DAI widget")
Link: https://github.com/thesofproject/linux/issues/5308
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20250509085318.13936-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Keep using the PIO mode for commands on ACE2+ platforms, similarly how
the legacy stack is configured.
Fixes: 05cf17f1bf ("ASoC: SOF: Intel: hda-bus: Use PIO mode for Lunar Lake")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250509081308.13784-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware does not provide any information for capture streams via the
shared pipeline registers.
To avoid reporting invalid delay value for capture streams to user space
we need to disable it.
Fixes: af74dbd0db ("ASoC: SOF: ipc4-pcm: allocate time info for pcm delay feature")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20250509085951.15696-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The header.numid is set to scontrol->comp_id in bytes_ext_get and it is
ignored during bytes_ext_put.
The use of comp_id is not quite great as it is kernel internal
identification number.
Set the header.numid to SOF_CTRL_CMD_BINARY during get and validate the
numid during put to provide consistent and compatible identification
number as IPC3.
For IPC4 existing tooling also ignored the numid but with the use of
SOF_CTRL_CMD_BINARY the different handling of the blobs can be dropped,
providing better user experience.
Reported-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Closes: https://github.com/thesofproject/linux/issues/5282
Fixes: a062c8899f ("ASoC: SOF: ipc4-control: Add support for bytes control get and put")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://patch.msgid.link/20250509085633.14930-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of our devices crash in tb_cfg_request_dequeue():
general protection fault, probably for non-canonical address 0xdead000000000122
CPU: 6 PID: 91007 Comm: kworker/6:2 Tainted: G U W 6.6.65
RIP: 0010:tb_cfg_request_dequeue+0x2d/0xa0
Call Trace:
<TASK>
? tb_cfg_request_dequeue+0x2d/0xa0
tb_cfg_request_work+0x33/0x80
worker_thread+0x386/0x8f0
kthread+0xed/0x110
ret_from_fork+0x38/0x50
ret_from_fork_asm+0x1b/0x30
The circumstances are unclear, however, the theory is that
tb_cfg_request_work() can be scheduled twice for a request:
first time via frame.callback from ring_work() and second
time from tb_cfg_request(). Both times kworkers will execute
tb_cfg_request_dequeue(), which results in double list_del()
from the ctl->request_queue (the list poison deference hints
at it: 0xdead000000000122).
Do not dequeue requests that don't have TB_CFG_REQUEST_ACTIVE
bit set.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Be more informative if memremap fails, and print out physical address
together with size. This change intends to make investigations of such
early failures slightly easier.
Signed-off-by: Bartosz Szczepanek <bsz@amazon.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Merge series from Biju Das <biju.das.jz@bp.renesas.com>:
The xSPI IP found on RZ/G3E SoC similar to RPC-IF interface, but it
can support writes on memory-mapped area. Even though the registers are
different, the rpcif driver code can be reused for xSPI by adding wrapper
functions.
The Libra board has an LVDS connector. Add an overlay for an
etml1010g3dra LVDS panel supported for the phyCORE-i.MX 8M Plus that may
be connected to it.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree for the Libra-i.MX 8M Plus FPSC board. The Libra is a
pure development board and has hardware to support FPSC-24-A.0 set of
features. It can be populated with the phyCORE-i.MX 8M Plus SoM to form
a SBC.
The phyCORE-i.MX 8M Plus FPSC [1] SoM uses only a subset of the hardware
features the Libra board provides. The phyCORE-i.MX8MP FPSC itself is a
System on Module based on the i.MX 8M Plus SoC utilizing the Future
Proof Solder Core [2] standard.
To be able to easily map FPSC interface names to SoC interfaces, the
FPSC interface names are added as inline comments. Example:
&i2c5 { /* FPSC I2C4 */
pinctrl-0 = <&pinctrl_i2c5>;
[...]
};
Here, I2C4 is the FPSC interface name. The i2c5 instance of the i.MX 8M Plus
SoC is used to fulfill the i2c functionality and its signals are routed
to the FPSC I2C4 signal pins:
pinctrl_i2c5: i2c5grp {
fsl,pins = <
MX8MP_IOMUXC_SPDIF_RX__I2C5_SDA 0x400001c2 /* I2C4_SDA */
MX8MP_IOMUXC_SAI5_RXD0__I2C5_SCL 0x400001c2 /* I2C4_SCL */
>;
};
The features are almost identical to the existing phyCORE-i.MX 8M Plus
SoM (dts: imx8mp-phycore-som.dtsi), but the pin muxing is different due
to the FPSC standard as well as 1.8V IO voltage instead of 3.3V.
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-8m-plus-fpsc/
[2] https://www.phytec.eu/en/produkte/system-on-modules/fpsc/
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mp-libra-rdk-fpsc is a development board based on the phyCORE-i.MX
8M Plus FPSC SoM. Add its description and binding. The
imx8mp-phycore-fpsc som differs from the existing phyCORE-i.MX 8M Plus
(dts: imx8mp-phycore-som.dtsi) in its physical form regarding the ball
grid array. Other differences between the SoMs are missing SPI-NOR on
this SoM and 1.8V IO voltage instead of 3.3V as found on the existing
imx8mp-phycore-som. As a result the imx8mp-phycore-som is not compatible
with this new libra development board.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
cirrus enables its PCI device with pcim_enable_device(). This,
implicitly, switches the function pci_request_regions() into managed
mode, where it becomes a devres function.
The PCI subsystem wants to remove this hybrid nature from its
interfaces. To do so, users of the aforementioned combination of
functions must be ported to non-hybrid functions.
Replace the call to sometimes-managed pci_request_regions() with one to
the always-managed pcim_request_all_regions().
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://lore.kernel.org/r/20250417094009.29297-2-phasta@kernel.org
The xe buffer object shrinker name is visible in the
<debugfs>/shrinker directory and most if not all other shinkers
follow a naming convention that looks like
<subsystem>-<driver>_<objects>:<unique>
Follow the same convention for xe, changing the name to
drm-xe_gem:<unique>.
Other shrinkers typically use the device node for <unique> but
since drm drivers typically don't have a single unique device-
node, instead use the unique name in the drm device.
Fixes: 00c8efc318 ("drm/xe: Add a shrinker for xe bos")
Cc: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Francois Dugast <francois.dugast@intel.com>
Link: https://lore.kernel.org/r/20250508112931.3347-1-thomas.hellstrom@linux.intel.com
kvasprintf() failure is often caused by memory allocation which has error
code -ENOMEM, but config_item_set_name() returns -EFAULT for the failure.
Fix by returning -ENOMEM instead of -EFAULT for the failure.
Reviewed-by: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250507-fix_configfs-v3-3-fe2d96de8dc4@quicinc.com
Signed-off-by: Andreas Hindborg <a.hindborg@kernel.org>
populate_attrs() may override failure for creating attribute files
by success for creating subsequent bin attribute files, and have
wrong return value.
Fix by creating bin attribute files under successfully creating
attribute files.
Fixes: 03607ace80 ("configfs: implement binary attributes")
Cc: stable@vger.kernel.org
Reviewed-by: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250507-fix_configfs-v3-2-fe2d96de8dc4@quicinc.com
Signed-off-by: Andreas Hindborg <a.hindborg@kernel.org>
Macro type_print() definition ends with semicolon, so will cause
the subsequent macro invocations end with two semicolons.
Fix by deleting the semicolon from the macro definition.
Reviewed-by: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250507-fix_configfs-v3-1-fe2d96de8dc4@quicinc.com
Signed-off-by: Andreas Hindborg <a.hindborg@kernel.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/20250425-gpiochip-set-rv-pinctrl-bcm-v1-3-6b8883d79b66@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/20250425-gpiochip-set-rv-pinctrl-bcm-v1-2-6b8883d79b66@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/20250425-gpiochip-set-rv-pinctrl-bcm-v1-1-6b8883d79b66@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
