commit aa179935ed upstream.
This patch adds a check to sbc_parse_cdb() in order to detect when
an LBA + sector vs. end-of-device calculation wraps when the LBA is
sufficently large enough (eg: 0xFFFFFFFFFFFFFFFF).
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 8e575c50a1 upstream.
This patch adds a check to sbc_setup_write_same() to verify
the incoming WRITE_SAME LBA + number of blocks does not exceed
past the end-of-device.
Also check for potential LBA wrap-around as well.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit f161d4b44d upstream.
This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.
It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.
It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit d180d2bbb6 upstream.
As per the specififcation, the SB_DevFn is the PCI_DEVFN of the target
device and not the source. So PCI_DEVFN(2,0) is not correct. Further the
port ID should be enough to identify devices unless they are MFD. The
SB_DevFn was intended to remove ambiguity in case of these MFD devices.
For non MFD devices the recommendation for the target device IP was to
ignore these fields, but not all of them followed the recommendation.
Some like CCK ignore these fields and hence PCI_DEVFN(2, 0) works and so
does PCI_DEVFN(0, 0) as it works for DPIO. The issue came to light because
of GPIONC which was not getting programmed correctly with PCI_DEVFN(2, 0).
It turned out that this did not follow the recommendation and expected 0
in this field.
In general the recommendation is to use SB_DevFn as PCI_DEVFN(0, 0) for
all devices except target PCI devices.
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 460822b0b1 upstream.
It's possible for invalidate_range_start mmu notifier callback to race
against userptr object release. If the gem object was released prior to
obtaining the spinlock in invalidate_range_start we're hitting null
pointer dereference.
Testcase: igt/gem_userptr_blits/stress-mm-invalidate-close
Testcase: igt/gem_userptr_blits/stress-mm-invalidate-close-overlap
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Jani: added code comment suggested by Chris]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 0ca0968554 upstream.
Nothing in Bspec seems to indicate that we actually needs this, and it
looks like can't work since by this point the pipe is off and so
vblanks won't really happen any more.
Note that Bspec mentions that it takes a vblank for this bit to
change, but _only_ when enabling.
Dropping this code quenches an annoying backtrace introduced by the
more anal checking since
commit 51e31d49c8
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Sep 15 12:36:02 2014 +0200
drm/i915: Use generic vblank wait
Note: This fixes the fallout from the above commit, but does not address
the shortcomings of the IBX transcoder select workaround implementation
discussed during review [1].
[1] http://mid.gmane.org/87y4o7usxf.fsf@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86095
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit f0a1fb10e5 upstream.
This looked like an odd regression from
commit ec5cc0f9b0
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Jun 12 10:28:55 2014 +0100
drm/i915: Restrict GPU boost to the RCS engine
but in reality it undercovered a much older coherency bug. The issue that
boosting the GPU frequency on the BCS ring was masking was that we could
wake the CPU up after completion of a BCS batch and inspect memory prior
to the write cache being fully evicted. In order to serialise the
breadcrumb interrupt (and so ensure that the CPU's view of memory is
coherent) we need to perform a post-sync operation in the MI_FLUSH_DW.
v2: Fix all the MI_FLUSH_DW (bsd plus the duplication in execlists).
Also fix the invalidate_domains mask in gen8_emit_flush() for ring !=
VCS.
Testcase: gpuX-rcs-gpu-read-after-write
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 09b6e85fc8 upstream.
Missing parameter when fetching the real voltage values
from atom. Fixes problems with dynamic clocking on
certain boards.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=87457
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 66c2b84ba6 upstream.
Don't restrict it to just eDP panels. Some LVDS bridge chips require
this. Fixes blank panels on resume on certain laptops. Noticed
by mrnuke on IRC.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=42960
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit a9c73a0e02 upstream.
Emit the EOP twice to avoid cache flushing problems.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 410af8d728 upstream.
Enable at init and disable on fini. Workaround for hardware problems.
v2 (chk): extend commit message
v3: add new function
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com> (v2)
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit a53fa43873 upstream.
Doing so can cause things to become slow.
Print a warning at compile time and an informative message at runtime in
that case.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88758
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 31f40f8652 upstream.
When copying a relocation from userspace, copy the correct target
offset.
Signed-off-by: David Ung <davidu@nvidia.com>
Fixes: 961e3beae3 ("drm/tegra: Make job submission 64-bit safe")
[treding@nvidia.com: provide a better commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 9215f437b8 ]
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 42c972a1f3 ]
The National Instruments USB Host-to-Host Cable is based on the Prolific
PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 4092e6acf5 ]
This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.
The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f ("tcp: refine TSO autosizing").
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2f1d8b9e8a ]
Brian reported crashes using IPv6 traffic with macvtap/veth combo.
I tracked the crashes in neigh_hh_output()
-> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD);
Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.
It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)
Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.
This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: Brian Rak <brak@vultr.com>
Tested-by: Brian Rak <brak@vultr.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 57e5956319 ]
Currently following race is possible in team:
CPU0 CPU1
team_port_del
team_upper_dev_unlink
priv_flags &= ~IFF_TEAM_PORT
team_handle_frame
team_port_get_rcu
team_port_exists
priv_flags & IFF_TEAM_PORT == 0
return NULL (instead of port got
from rx_handler_data)
netdev_rx_handler_unregister
The thing is that the flag is removed before rx_handler is unregistered.
If team_handle_frame is called in between, team_port_exists returns 0
and team_port_get_rcu will return NULL.
So do not check the flag here. It is guaranteed by netdev_rx_handler_unregister
that team_handle_frame will always see valid rx_handler_data pointer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
This reverts commit 1e91887685.
Revert BQL support in r8169 driver as several regressions
point to this commit and we cannot figure out the real
cause yet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 54da5a8be3 ]
phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex)
to find a valid entry in the settings array for the given speed
and duplex value. For full duplex 1000baseT, this will return
the first matching entry, which is the entry for 1000baseKX_Full.
If the phy eee does not support 1000baseKX_Full, this entry will not
match, causing phy_init_eee to fail for no good reason.
Fixes: 9a9c56cb34 ("net: phy: fix a bug when verify the EEE support")
Fixes: 3e7077067e ("phy: Expand phy speed/duplex settings array")
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 4690555e13 upstream.
Since kernel 3.14 the backlight control has been broken on various Samsung
Atom based netbooks. This has been bisected and this problem happens since
commit b35684b8fa ("drm/i915: do full backlight setup at enable time")
This has been reported and discussed in detail here:
http://lists.freedesktop.org/archives/intel-gfx/2014-July/049395.html
Unfortunately no-one has been able to fix this. This only affects Samsung
Atom netbooks, and the Linux kernel and the BIOS of those laptops have never
worked well together. All affected laptops already have a quirk to avoid using
the standard acpi-video interface and instead use the samsung specific SABI
interface which samsung-laptop uses. It seems that recent fixes to the i915
driver have also broken backlight control through the SABI interface.
The intel_backlight driver OTOH works fine, and also allows for finer grained
backlight control. So add a new use_native_backlight quirk, and replace the
broken_acpi_video quirk with this quirk for affected models. This new quirk
disables acpi-video as before and also stops samsung-laptop from registering
the SABI based samsung_laptop backlight interface, leaving only the working
intel_backlight interface.
This commit enables this new quirk for 3 models which are known to be affected,
chances are that it needs to be used on other models too.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1094948 # N145P
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1115713 # N250P
Reported-by: Bertrik Sikken <bertrik@sikken.nl> # N150P
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11249e7399 upstream.
d0585cd815 ("sb_edac: Claim a different PCI device") changed the
probing of sb_edac to look for PCI device 0x3ca0:
3f:0e.0 System peripheral: Intel Corporation Xeon E5/Core i7 Processor Home Agent (rev 07)
00: 86 80 a0 3c 00 00 00 00 07 00 80 08 00 00 80 00
...
but we're matching for 0x3ca8, i.e. PCI_DEVICE_ID_INTEL_SBRIDGE_IMC_TA
in sbridge_probe() therefore the probing fails.
Changing it to probe for 0x3ca0 (PCI_DEVICE_ID_INTEL_SBRIDGE_IMC_HA0),
.i.e., the 14.0 device, fixes the issue and driver loads successfully
again:
[ 2449.013120] EDAC DEBUG: sbridge_init:
[ 2449.017029] EDAC sbridge: Seeking for: PCI ID 8086:3ca0
[ 2449.022368] EDAC DEBUG: sbridge_get_onedevice: Detected 8086:3ca0
[ 2449.028498] EDAC sbridge: Seeking for: PCI ID 8086:3ca0
[ 2449.033768] EDAC sbridge: Seeking for: PCI ID 8086:3ca8
[ 2449.039028] EDAC DEBUG: sbridge_get_onedevice: Detected 8086:3ca8
[ 2449.045155] EDAC sbridge: Seeking for: PCI ID 8086:3ca8
...
Add a debug printk while at it to be able to catch the failure in the
future and dump driver version on successful load.
Fixes: d0585cd815 ("sb_edac: Claim a different PCI device")
Acked-by: Aristeu Rozanski <aris@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1901ef099 upstream.
When a drive is marked write-mostly it should only be the
target of reads if there is no other option.
This behaviour was broken by
commit 9dedf60313
md/raid1: read balance chooses idlest disk for SSD
which causes a write-mostly device to be *preferred* is some cases.
Restore correct behaviour by checking and setting
best_dist_disk and best_pending_disk rather than best_disk.
We only need to test one of these as they are both changed
from -1 or >=0 at the same time.
As we leave min_pending and best_dist unchanged, any non-write-mostly
device will appear better than the write-mostly device.
Reported-by: Tomáš Hodek <tomas.hodek@volny.cz>
Reported-by: Dark Penguin <darkpenguin@yandex.ru>
Signed-off-by: NeilBrown <neilb@suse.de>
Link: http://marc.info/?l=linux-raid&m=135982797322422
Fixes: 9dedf60313
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26ac107378 upstream.
Commit a7854487cd:
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.
Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.
So change the condition to only force RCW on non-degraded arrays.
Reported-by: Manibalan P <pmanibalan@amiindia.co.in>
Bisected-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: a7854487cd
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4a19eb3b1 upstream.
We have two race conditions in the probe code which could lead to a null
pointer dereference in the interrupt handler.
The interrupt handler accesses the clockevent device, which may not yet be
registered.
First race condition happens when the interrupt handler gets registered before
the interrupts get disabled. The second race condition happens when the
interrupts get enabled, but the clockevent device is not yet registered.
Fix that by disabling the interrupts before we register the interrupt and enable
the interrupts after the clockevent device got registered.
Reported-by: Gongbae Park <yongbae2@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f97c20e5f upstream.
The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cf75e9e4d upstream.
The change:
7b8792bbdf
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
assumed that only one gpio-chip is registred per of-node.
Some drivers register more than one chip per of-node, so
adjust the matching function of_gpiochip_find_and_xlate to
not stop looking for chips if a node-match is found and
the translation fails.
Fixes: 7b8792bbdf ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags")
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Tyler Hall <tylerwhall@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f1437f61a upstream.
When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:
[ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
[ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
[ 74.373960] LR is at lpuart_int+0x15c/0x3d8
[ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
[ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
[ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
[ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
[ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
[ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
[ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...
Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.
This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a8588a1cf upstream.
If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:
[ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.516590] pgd = 86348000
[ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[ 7.526145] Internal error: Oops: 17 [#1] ARM
[ 7.530611] Modules linked in:
[ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
[ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
[ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
[ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
[ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
[ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
[ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
[ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
[ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19e3ae6b4f upstream.
The vcs device's poll/fasync support relies on the vt notifier to signal
changes to the screen content. Notifier invocations were missing for
changes that comes through the selection interface though. Fix that.
Tested with BRLTTY 5.2.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: Dave Mielke <dave@mielke.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 074f9dd55f upstream.
Currently the USB stack assumes that all host controller drivers are
capable of receiving wakeup requests from downstream devices.
However, this isn't true for the isp1760-hcd driver, which means that
it isn't safe to do a runtime suspend of any device attached to a
root-hub port if the device requires wakeup.
This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure
and sets the flag in isp1760-hcd. The core is modified to prevent a
direct child of the root hub from being put into runtime suspend with
wakeup enabled if the flag is set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 524134d422 upstream.
The USB stack provides a mechanism for drivers to request an
asynchronous device reset (usb_queue_reset_device()). The mechanism
uses a work item (reset_ws) embedded in the usb_interface structure
used by the driver, and the reset is carried out by a work queue
routine.
The asynchronous reset can race with driver unbinding. When this
happens, we try to cancel the queued reset before unbinding the
driver, on the theory that the driver won't care about any resets once
it is unbound.
However, thanks to the fact that lockdep now tracks work queue
accesses, this can provoke a lockdep warning in situations where the
device reset causes another interface's driver to be unbound; see
http://marc.info/?l=linux-usb&m=141893165203776&w=2
for an example. The reason is that the work routine for reset_ws in
one interface calls cancel_queued_work() for the reset_ws in another
interface. Lockdep thinks this might lead to a work routine trying to
cancel itself. The simplest solution is not to cancel queued resets
when unbinding drivers.
This means we now need to acquire a reference to the usb_interface
when queuing a reset_ws work item and to drop the reference when the
work routine finishes. We also need to make sure that the
usb_interface structure doesn't outlive its parent usb_device; this
means acquiring and dropping a reference when the interface is created
and destroyed.
In addition, cancelling a queued reset can fail (if the device is in
the middle of an earlier reset), and this can cause usb_reset_device()
to try to rebind an interface that has been deallocated (see
http://marc.info/?l=linux-usb&m=142175717016628&w=2 for details).
Acquiring the extra references prevents this failure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Reported-by: Olivier Sobrie <olivier@sobrie.be>
Tested-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5efd2ea8c9 upstream.
the following error pops up during "testusb -a -t 10"
| musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128, f134e000/be842000 (bad dma)
hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of
size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in
hcd_buffer_alloc() returning memory which is 32 bytes aligned and it
might by identified by buffer_offset() as another buffer. This means the
buffer which is on a 32 byte boundary will not get freed, instead it
tries to free another buffer with the error message.
This patch fixes the issue by creating the smallest DMA buffer with the
size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is
smaller). This might be 32, 64 or even 128 bytes. The next three pools
will have the size 128, 512 and 2048.
In case the smallest pool is 128 bytes then we have only three pools
instead of four (and zero the first entry in the array).
The last pool size is always 2048 bytes which is the assumed PAGE_SIZE /
2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where
we would end up with 8KiB buffer in case we have 16KiB pages.
Instead I think it makes sense to have a common size(s) and extend them
if there is need to.
There is a BUILD_BUG_ON() now in case someone has a minalign of more than
128 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c99197902d upstream.
The usb_hcd_unlink_urb() routine in hcd.c contains two possible
use-after-free errors. The dev_dbg() statement at the end of the
routine dereferences urb and urb->dev even though both structures may
have been deallocated.
This patch fixes the problem by storing urb->dev in a local variable
(avoiding the dereference of urb) and moving the dev_dbg() up before
the usb_put_dev() call.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6f0331236 upstream.
Added the USB serial console device ID for Siemens Ruggedcom devices
which have a USB port for their serial console.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 663b7ee951 upstream.
We might enter the interrupt handler with hw_ready already set,
but prior we actually started the reset flow.
To soleve this we move the reset release from the interrupt handler
to the HW start wait function which is part of the reset sequence.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ab1e79b9f upstream.
We should mask interrupt set bit when writing back
hcsr value in reset bit clean-up.
This is refinement for
mei: clean reset bit before reset
commit b13a65ef19
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fbb9bdf0f upstream.
-EDEFER error wasn't handle properly by atmel_serial_probe().
As an example, when atmel_serial_probe() is called for the first time, we pass
the test_and_set_bit() test to check whether the port has already been
initalized. Then we call atmel_init_port(), which may return -EDEFER, possibly
returned before by clk_get(). Consequently atmel_serial_probe() used to return
this error code WITHOUT clearing the port bit in the "atmel_ports_in_use" mask.
When atmel_serial_probe() was called for the second time, it used to fail on
the test_and_set_bit() function then returning -EBUSY.
When atmel_serial_probe() fails, this patch make it clear the port bit in the
"atmel_ports_in_use" mask, if needed, before returning the error code.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37480a0568 upstream.
Commit 26df6d1340 ("tty: Add EXTPROC support for LINEMODE")
allows a process which has opened a pty master to send _any_ signal
to the process group of the pty slave. Although potentially
exploitable by a malicious program running a setuid program on
a pty slave, it's unknown if this exploit currently exists.
Limit to signals actually used.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Howard Chu <hyc@symas.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7772855a99 upstream.
With scsi-mq enabled, userspace programs can get unexpected EWOULDBLOCK
(a.k.a. EAGAIN) errors when submitting commands to the SCSI generic
driver. Fix by calling blk_get_request() with GFP_KERNEL instead of
GFP_ATOMIC.
Note: to avoid introducing a potential deadlock, this patch should be
applied after the patch titled "sg: fix unkillable I/O wait deadlock
with scsi-mq".
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7568615c10 upstream.
When using the write()/read() interface for submitting commands, the
SCSI generic driver does not call blk_put_request() on a completed SCSI
command until userspace calls read() to get the command completion.
Since scsi-mq uses a fixed number of preallocated requests, this makes
it possible for userspace to exhaust the entire preallocated supply of
requests. For places in the kernel that call blk_get_request() with
GFP_KERNEL, this can cause the calling process to deadlock in a
permanent unkillable I/O wait in blk_get_request() -> ... -> bt_get().
For places in the kernel that call blk_get_request() with GFP_ATOMIC,
this can cause blk_get_request() always to return -EWOULDBLOCK. Note
that these problems happen only if scsi-mq is enabled. Prevent the
problems by calling blk_put_request() as soon as the SCSI command
completes instead of waiting for userspace to call read().
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb71f8a5e3 upstream.
The tpm_ibmvtpm module is affected by an unaligned access problem.
ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is
enabled in Power partition, which supports both little endian and
big endian modes.
We added little endian support to fix this problem:
1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS.
2) added be16_to_cpu and be32_to_cpu calls to make sure data received
is in LE format on a LE OS.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
[phuewe: manually applied the patch :( ]
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ba3b0b6f2 upstream.
When sending data in tpm_stm_i2c_send, each loop iteration send buf.
Send buf + i instead as the goal of this for loop is to send a number
of byte from buf that fit in burstcnt. Once those byte are sent, we are
supposed to send the next ones.
The driver was working because the burstcount value returns always the maximum size for a TPM
command or response. (0x800 for a command and 0x400 for a response).
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84eb186bc3 upstream.
There was an oops in tpm_ibmvtpm_get_desired_dma, which caused
kernel panic during boot when vTPM is enabled in Power partition
configured in AMS mode.
vio_bus_probe calls vio_cmo_bus_probe which calls
tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation.
The problem is, vio_cmo_bus_probe is called before calling probe, which
for vtpm is tpm_ibmvtpm_probe and it's this function that initializes
and sets up vtpm's CRQ and gets required data values. Therefore,
since this has not yet been done, NULL is returned in attempt to get
the size for DMA allocation.
We added a NULL check. In addition, a default buffer size will
be set when NULL is returned.
Signed-off-by: Hon Ching (Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb95cd34ba upstream.
Currently these driver are missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds a missing check for tpm_i2c_atmel.c and tpm_i2c_nuvoton.c
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 398a1e71dc upstream.
Add newly registered TPMs to the tail of the list, not the beginning, so that
things that are specifying TPM_ANY_NUM don't find that the device they're
using has inadvertently changed. Adding a second device would break IMA, for
instance.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 448e9c55c1 upstream.
Some machines, such as the Acer C720 and Toshiba CB35, have TPMs that do
not send IRQs while also having an ACPI TPM entry indicating that they
will be sent. These machines freeze on resume while the tpm_tis module
waits for an IRQ, eventually timing out.
When in interrupt mode, the tpm_tis module should receive an IRQ during
module init. Fall back to polling mode if none is received when expected.
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor checkpatch fixed]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a39128bcd6 upstream.
According to erratum 'ERR-7878951' Armada 38x SDHCI controller has
different capabilities than the ones shown in its registers:
- it doesn't support the voltage switching: it can work either with
3.3V or 1.8V supply
- it doesn't support the SDR104 mode
- SDR50 mode doesn't need tuning
The SDHCI_QUIRK_MISSING_CAPS quirk is used for updating the
capabilities accordingly.
[gregory.clement@free-electrons.com: port from 3.10]
Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
