Clang Static Checker (scan-build) warns:
drivers/net/wireless/ath/ath10k/debugfs_sta.c:line 429, column 3
Value stored to 'ret' is never read.
Return 'ret' rather than 'count' when 'ret' stores an error code.
Fixes: ee8b08a1be ("ath10k: add debugfs support to get per peer tids log via tracing")
Signed-off-by: Su Hui <suhui@nfschina.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422034243.938962-1-suhui@nfschina.com
Currently, mlo_capable_flags is set to zero if dualmac device is
detected based on One Time Programmable (OTP) register value.
This is not generic and in future dualmac devices may support
Single Link Operation (SLO) and Multi Link Operation (MLO).
Thus, set mlo_capable_flags based on 'single_chip_mlo_support'
parameter from QMI PHY capability response message from the firmware.
Also, add check on mlo_capable_flags to disable MLO parameter in the
host capability QMI request message.
If the firmware does not respond with this optional parameter
'single_chip_mlo_support' in QMI PHY capability response, default
ab->mlo_capable_flags is used.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240418125609.3867730-3-quic_rajkbhag@quicinc.com
New parameter 'single_chip_mlo_support' was added in QMI PHY
capability response message. This is an optional parameter added
in QCN9274 firmware. This parameter states if the firmware
supports Single-Link Operation (SLO) and Multi-Link Operation (MLO)
within the same device.
If single_chip_mlo_support = 1, then intra device SLO/MLO is supported
in the firmware.
If single_chip_mlo_support = 0, then intra device SLO/MLO is not
supported in the firmware.
Hence, add support to read 'single_chip_mlo_support' parameter from
the QMI PHY capability response message.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240418125609.3867730-2-quic_rajkbhag@quicinc.com
When AP goes down or too far away without indication to STA, beacon miss
will be detected. Then for WCN7850's firmware, it will use roam event
to send beacon miss to host.
If STA doesn't handle the beacon miss, will keep the fake connection
and unable to roam.
So add support for WCN7850 to trigger disconnection from AP when
receiving this event from firmware.
It has to be noted that beacon miss event notification for QCN9274
to be handled in a separate patch as it uses STA kickout WMI event
to notify beacon miss and the current STA kickout event is processed
as low_ack.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412094447.2063-1-quic_kangyang@quicinc.com
By default CT code was passing just payload of the G2H event
message, while Relay code expects full G2H message including
HXG header which contains DATA0 field. Fix that.
Fixes: 26d4481ac2 ("drm/xe/guc: Start handling GuC Relay event messages")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240419150351.358-1-michal.wajdeczko@intel.com
(cherry picked from commit 48c64d495f)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
The drmm_add_action_or_reset function automatically invokes the
action (free_gsc_pkt) in the event of a failure; therefore, there's no
necessity to call it within the return check.
-v2
Fix commit message. (Lucas)
Fixes: d8b1571312 ("drm/xe/huc: HuC authentication via GSC")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412181211.1155732-4-himal.prasad.ghimiray@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 22bf0bc04d)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
The drmm_add_action_or_reset function automatically invokes the action
(sysfs removal) in the event of a failure; therefore, there's no
necessity to call it within the return check.
Modify the return type of xe_gt_ccs_mode_sysfs_init to int, allowing the
caller to pass errors up the call chain. Should sysfs creation or
drmm_add_action_or_reset fail, error propagation will prompt a driver
load abort.
-v2
Edit commit message (Nikula/Lucas)
use err_force_wake label instead of new. (Lucas)
Avoid unnecessary warn/error messages. (Lucas)
Fixes: f3bc5bb4d5 ("drm/xe: Allow userspace to configure CCS mode")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412181211.1155732-3-himal.prasad.ghimiray@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit a99641e387)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
The TDX guest platform takes one bit from the physical address to
indicate if the page is shared (accessible by VMM). This bit is not part
of the physical_mask and is not preserved during mprotect(). As a
result, the 'shared' bit is lost during mprotect() on shared mappings.
_COMMON_PAGE_CHG_MASK specifies which PTE bits need to be preserved
during modification. AMD includes 'sme_me_mask' in the define to
preserve the 'encrypt' bit.
To cover both Intel and AMD cases, include 'cc_mask' in
_COMMON_PAGE_CHG_MASK instead of 'sme_me_mask'.
Reported-and-tested-by: Chris Oo <cho@microsoft.com>
Fixes: 41394e33f3 ("x86/tdx: Extend the confidential computing API to support TDX guests")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240424082035.4092071-1-kirill.shutemov%40linux.intel.com
Instead of reiterating the list, use list_for_each_entry_safe()
that allows to continue without starting over.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Message-ID: <20240424145020.1057216-1-andriy.shevchenko@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Program live video input format according to selected media bus format.
In the bridge mode of operation, DPSUB is connected to FPGA CRTC which
almost certainly supports a single media bus format as its output. Expect
this to be delivered via the new bridge atomic state. Program DPSUB
registers accordingly.
Signed-off-by: Anatoliy Klymenko <anatoliy.klymenko@amd.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-dp-live-fmt-v4-6-c7f379b7168e@amd.com
Avoid usage of global zynqmp_dpsub.dma_enabled flag in DPSUB layer
context. This flag signals whether the driver runs in DRM CRTC or DRM
bridge mode, assuming that all display layers share the same live or
non-live mode of operation. Using per-layer mode instead of global flag
will simplify future support of the hybrid scenario.
Remove redundant checks in DMA request/release contexts as
zynqmp_disp_layer.info is well-defined for all layer types, including the
correct number of DMA channels required for each particular layer.
Signed-off-by: Anatoliy Klymenko <anatoliy.klymenko@amd.com>
Reviewed-by: Tomi Valkeinen <tomi.valkainen@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-dp-live-fmt-v4-5-c7f379b7168e@amd.com
DPSUB in bridge mode supports multiple input media bus formats.
Announce the list of supported input media bus formats via
drm_bridge.atomic_get_input_bus_fmts callback. Introduce a set of live
input formats supported by DPSUB. Add safeguards to format list functions
to prevent their misuse in the different layer modes contexts.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Anatoliy Klymenko <anatoliy.klymenko@amd.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-dp-live-fmt-v4-4-c7f379b7168e@amd.com
Add a helper function capturing the first connected live display layer
discovery logic.
Signed-off-by: Anatoliy Klymenko <anatoliy.klymenko@amd.com>
Reviewed-by: Tomi Valkeinen <tomi.valkainen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-dp-live-fmt-v4-3-c7f379b7168e@amd.com
Update live format defines to match DPSUB AV_BUF_LIVE_VID_CONFIG register
layout. These defines were never referenced before, so no other changes
required.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Anatoliy Klymenko <anatoliy.klymenko@amd.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-dp-live-fmt-v4-2-c7f379b7168e@amd.com
Set layer mode of operation (live or dma-based) during layer creation.
Each DPSUB layer mode of operation is defined by corresponding DT node port
connection, so it is possible to assign it during layer object creation.
Previously it was set in layer enable functions, although it is too late
as setting layer format depends on layer mode, and should be done before
given layer enabled.
Signed-off-by: Anatoliy Klymenko <anatoliy.klymenko@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkainen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-dp-live-fmt-v4-1-c7f379b7168e@amd.com
The controller has several register bits describing access control
information for a given GPIO pin. When SCR_SEC_[R|W]EN is unset, it
means we have full read/write access to all the registers for given GPIO
pin. When SCR_SEC[R|W]EN is set, it means we need to further check the
accompanying SCR_SEC_G1[R|W] bit to determine read/write access to all
the registers for given GPIO pin.
This check was previously declaring that a GPIO pin was accessible
only if either of the following conditions were met:
- SCR_SEC_REN + SCR_SEC_WEN both set
or
- SCR_SEC_REN + SCR_SEC_WEN both set and
SCR_SEC_G1R + SCR_SEC_G1W both set
Update the check to properly handle cases where only one of
SCR_SEC_REN or SCR_SEC_WEN is set.
Fixes: b2b56a1632 ("gpio: tegra186: Check GPIO pin permission before access.")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240424095514.24397-1-pshete@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The "msg" pointer is a struct and msg->offset is the sizeof(*msg). The
pointer here math means the memcpy() will write outside the bounds.
Cast "msg" to a u8 pointer to fix this.
Fixes: 02c19d84c7 ("firmware: arm_ffa: Add support for FFA_MSG_SEND2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/cd5fb6b5-81fa-4a6d-b2b8-284ca704bbff@moroto.mountain
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
With deferred IO enabled, a page fault happens when data is written to the
framebuffer device. Then driver determines which page is being updated by
calculating the offset of the written virtual address within the virtual
memory area, and uses this offset to get the updated page within the
internal buffer. This page is later copied to hardware (thus the name
"deferred IO").
This offset calculation is only correct if the virtual memory area is
mapped to the beginning of the internal buffer. Otherwise this is wrong.
For example, if users do:
mmap(ptr, 4096, PROT_WRITE, MAP_FIXED | MAP_SHARED, fd, 0xff000);
Then the virtual memory area will mapped at offset 0xff000 within the
internal buffer. This offset 0xff000 is not accounted for, and wrong page
is updated.
Correct the calculation by using vmf->pgoff instead. With this change, the
variable "offset" will no longer hold the exact offset value, but it is
rounded down to multiples of PAGE_SIZE. But this is still correct, because
this variable is only used to calculate the page offset.
Reported-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Closes: https://lore.kernel.org/linux-fbdev/271372d6-e665-4e7f-b088-dee5f4ab341a@oracle.com
Fixes: 56c134f7f1 ("fbdev: Track deferred-I/O pages in pageref struct")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240423115053.4490-1-namcao@linutronix.de
Intel pre-USB4 routers only have ROUTER_CS_0 up to ROUTER_CS_4 and it
immediately follows the TMU router registers. Correct this accordingly.
Reported-by: Rajaram Regupathy <rajaram.regupathy@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Directories do not support direct I/O and thus no non-blocking direct
I/O either. Open code the shutdown check and call to generic_file_open
instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240423124608.537794-4-hch@lst.de
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Directories have non of the capabilities, so drop the flags. Note that
the current state is harmless as no one actually checks for the flags
either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240423124608.537794-3-hch@lst.de
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Re-wrap the newly added fop_flags fields to not go over 80 characters.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240423124608.537794-2-hch@lst.de
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
RIFSC is a peripheral firewall controller that filter accesses based on
Arm TrustZone secure state, Arm CPU privilege execution level and
Compartment IDentification of the STM32 SoC subsystems.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
cpu_feature_enabled(X86_FEATURE_OSPKE) does not necessarily reflect
whether CR4.PKE is set on the CPU. In particular, they may differ on
non-BSP CPUs before setup_pku() is executed. In this scenario, RDPKRU
will #UD causing the system to hang.
Fix by checking CR4 for PKE enablement which is always correct for the
current CPU.
The scenario happens by inserting a WARN* before setup_pku() in
identiy_cpu() or some other diagnostic which would lead to calling
__show_regs().
[ bp: Massage commit message. ]
Signed-off-by: David Kaplan <david.kaplan@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240421191728.32239-1-bp@kernel.org
In our production environment, after removing monitor groups, those
unused RMIDs get stuck in the limbo list forever because their
llc_occupancy is always larger than the threshold. But the unused RMIDs
can be successfully freed by turning up the threshold.
In order to know how much the threshold should be, perf can be used to
acquire the llc_occupancy of RMIDs in each rdt domain.
Instead of using perf tool to track llc_occupancy and filter the log
manually, it is more convenient for users to use tracepoint to do this
work. So add a new tracepoint that shows the llc_occupancy of busy RMIDs
when scanning the limbo list.
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Haifeng Xu <haifeng.xu@shopee.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lore.kernel.org/r/20240408092303.26413-3-haifeng.xu@shopee.com
Now only the pseudo-locking part uses tracepoints to do event tracking,
but other parts of resctrl may need new tracepoints. It is unnecessary
to create separate header files and define CREATE_TRACE_POINTS in
different c files which fragments the resctrl tracing.
Therefore, give the resctrl tracepoint header file a generic name to
support its use for tracepoints that are not specific to pseudo-locking.
No functional change.
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Haifeng Xu <haifeng.xu@shopee.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lore.kernel.org/r/20240408092303.26413-2-haifeng.xu@shopee.com
Daniel Machon says:
====================
net: sparx5: add support for port mirroring
This series adds support for port mirroring, and port mirroring stats,
through tc matchall action FLOW_ACTION_MIRRED.
The hardware has three independent mirroring probes. Each probe can be
configured with a separate set of filtering conditions that must be
fulfilled before traffic is mirrored.
A mirror probe can have up to 64 source ports and a single monitor port.
The direction of a mirror probe determines if rx or tx traffic is
mirrored from the source port to the monitor port.
To: David S. Miller <davem@davemloft.net>
To: Eric Dumazet <edumazet@google.com>
To: Jakub Kicinski <kuba@kernel.org>
To: Paolo Abeni <pabeni@redhat.com>
To: Lars Povlsen <lars.povlsen@microchip.com>
To: Steen Hegelund <Steen.Hegelund@microchip.com>
To: UNGLinuxDriver@microchip.com
To: Russell King <linux@armlinux.org.uk>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Yue Haibing <yuehaibing@huawei.com>
---
Changes in v3:
- Ditch do_div() (patch #3) to fix warning on hexagon arch, reported by intel bot
- Link to v2: https://lore.kernel.org/r/20240418-port-mirroring-v2-0-20642868b386@microchip.com
Changes in v2:
- Fix clang build warning about uninitialized variable 'err'
- Link to v1: https://lore.kernel.org/r/20240418-port-mirroring-v1-0-e05c35007c55@microchip.com
====================
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tc matchall mirror stats. When a new matchall mirror
rule is added, the baseline stats for that port is saved.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary tc glue to add and delete mirror rules through tc
matchall.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports three independent mirroring probes. Each probe can
be configured to mirror rx or tx traffic (direction).
Using tc matchall, it is now possible to add a source port and a monitor
port to a mirror probe. Depending on the mirror direction, rx or tx
traffic from a source port will be mirrored to the monitor port.
A single source port can be a member of multiple mirror probes.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for new tc matchall rules, we add a bit of bookkeeping
code to keep track of them. The rules are identified by the cookie
passed from the tc stack.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for port mirroring support through tc matchall, add the
required register definitions.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subtract in this condition is reversed. The ->length is the length
of the buffer. The ->bytesused is how many bytes we have copied thus
far. When the condition is reversed that means the result of the
subtraction is always negative but since it's unsigned then the result
is a very high positive value. That means the overflow check is never
true.
Additionally, the ->bytesused doesn't actually work for this purpose
because we're not writing to "buf->mem + buf->bytesused". Instead, the
math to calculate the destination where we are writing is a bit
involved. You calculate the number of full lines already written,
multiply by two, skip a line if necessary so that we start on an odd
numbered line, and add the offset into the line.
To fix this buffer overflow, just take the actual destination where we
are writing, if the offset is already out of bounds print an error and
return. Otherwise, write up to buf->length bytes.
Fixes: 9cb2173e6e ("[media] media: Add stk1160 new driver (easycap replacement)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The JPEG decoder/encoder present in iMX8QXP and iMX8QM SoCs need
the PER and IPG clocks to be functional, so add the clock entries.
This also fixes the following schema warning:
imx8qm-apalis-eval.dtb: jpegdec@58400000: 'assigned-clock-rates', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/media/nxp,imx8-jpeg.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Ensure that drivers set max_num_buffers to a value >= 32.
For now there is no reason for drivers to request a lower
limit and doing so might potentially cause userspace issues.
Note that the old check of > MAX_BUFFER_INDEX was pointless
since q->max_num_buffers was already limited to MAX_BUFFER_INDEX
or less.
Also add a sanity check in __vb2_init_fileio(), returning
-ENOSPC if a driver returns more than 32 buffers from
VIDIOC_REQBUFS with count = q->min_reqbufs_allocation.
The vb2_fileio_data struct only supports up to 32 buffers,
so we need a check there.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The error that V4L2 returns when an attempt is made to open an
unregisted device node is ENODEV, no ENXIO. Update the documentation.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
If the CEC device is unregistered, then an attempt to open
the device node should result in an -ENODEV error instead of
-ENXIO.
Document this as well in cec-func-open.rst.
This is consistent with the error code returned by other
file operations such as ioctl.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
After the new V4L2 device node was registered, some additional
initialization was done before the device node was marked as
'registered'. During the time between creating the device node
and marking it as 'registered' it was possible to open the
device node, which would return -ENODEV since the 'registered'
flag was not yet set.
Hold the videodev_lock mutex from just before the device node
is registered until the 'registered' flag is set. Since v4l2_open
will take the same lock, it will wait until this registration
process is finished. This resolves this race condition.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: <stable@vger.kernel.org> # for vi4.18 and up
The per-resource MSR update functions cat_wrmsr(), mba_wrmsr_intel(),
and mba_wrmsr_amd() all take three arguments:
(struct rdt_domain *d, struct msr_param *m, struct rdt_resource *r)
struct msr_param contains pointers to both struct rdt_resource and struct
rdt_domain, thus only struct msr_param is necessary.
Pass struct msr_param as a single parameter. Clean up formatting and
fix some fir tree declaration ordering.
No functional change.
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Maciej Wieczor-Retman <maciej.wieczor-retman@intel.com>
Link: https://lore.kernel.org/r/20240308213846.77075-3-tony.luck@intel.com
reset_all_ctrls() and resctrl_arch_update_domains() use on_each_cpu_mask()
to call rdt_ctrl_update() on potentially one CPU from each domain.
But this means rdt_ctrl_update() needs to figure out which domain to
apply changes to. Doing so requires a search of all domains in a resource,
which can only be done safely if cpus_lock is held. Both callers do hold
this lock, but there isn't a way for a function called on another CPU
via IPI to verify this.
Commit
c0d848fcb0 ("x86/resctrl: Remove lockdep annotation that triggers
false positive")
removed the incorrect assertions.
Add the target domain to the msr_param structure and call
rdt_ctrl_update() for each domain separately using
smp_call_function_single(). This means that rdt_ctrl_update() doesn't
need to search for the domain and get_domain_from_cpu() can safely
assert that the cpus_lock is held since the remaining callers do not use
IPI.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Maciej Wieczor-Retman <maciej.wieczor-retman@intel.com>
Link: https://lore.kernel.org/r/20240308213846.77075-2-tony.luck@intel.com
Breno Leitao says:
====================
allocate dummy device dynamically
struct net_device shouldn't be embedded into any structure, instead,
the owner should use the private space to embed their state into
net_device.
But, in some cases the net_device is embedded inside the private
structure, which blocks the usage of zero-length arrays inside
net_device.
Create a helper to allocate a dummy device at dynamically runtime, and
move the Ethernet devices to use it, instead of embedding the dummy
device inside the private structure.
This fixes all the network cases plus some wireless drivers.
PS: Due to lack of hardware, unfortunately most these patches are
compiled tested only, except ath11k that was kindly tested by Kalle Valo.
---
Changelog:
v7:
* Document the return value of alloc_netdev_dummy()
v6:
* No code change. Just added Reviewed-by: and fix a commit message
v5:
* Added a new patch to fix some typos in the previous code
* Rebased to net-net/main
v4:
* Added a new patch to add dummy device at free_netdev(), as suggested
by Jakub.
* Added support for some wireless driver.
* Added some Acked-by and Reviewed-by.
v3:
* Use free_netdev() instead of kfree() as suggested by Jakub.
* Change the free_netdev() place in ipa driver, as suggested by
Alex Elder.
* Set err in the error path in the Marvell driver, as suggested
by Simon Horman.
v2:
* Patch 1: Use a pre-defined name ("dummy#") for the dummy
net_devices.
* Patch 2-5: Added users for the new helper.
v1:
* https://lore.kernel.org/all/20240327200809.512867-1-leitao@debian.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct ath11k_ext_irq_grp by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at ath11k_ahb_config_ext_irq() for ahb, and
ath11k_pcic_ext_irq_config() for pcic.
The free of the device occurs at ath11k_ahb_free_ext_irq() for the ahb
case, and ath11k_pcic_free_ext_irq() for the pcic case.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Tested-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct ath10k by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at ath10k_core_create(). The free of the device occurs
at ath10k_core_destroy().
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a new dummy netdev allocator, use it instead of
alloc_netdev()/init_dummy_netdev combination.
Using alloc_netdev() with init_dummy_netdev might cause some memory
corruption at the driver removal side.
Fixes: 61cdb09ff7 ("wifi: qtnfmac: allocate dummy net_device dynamically")
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>