Bindings expect NAND controllers to match certain pattern:
s5pv210-fascinate4g.dtb: onenand@b0600000: $nodename:0: 'onenand@b0600000' does not match '^nand-controller(@.*)?'
Link: https://lore.kernel.org/r/20240313191148.21792-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
'samsung,hpd-gpio' property is deprecated and uses also deprecated
'gpio' suffix which is not matched by dtbs_check:
exynos5800-peach-pi.dtb: dp-controller@145b0000: 'samsung,hpd-gpio' does not match any of the regexes: 'pinctrl-[0-9]+'
Switch to hpd-gpios property.
Link: https://lore.kernel.org/r/20240313183011.14253-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
This reverts commit d794734c9b.
While the original change tries to fix a bug, it also unintentionally broke
existing systems, see the regressions reported at:
https://lore.kernel.org/all/3a1b9909-45ac-4f97-ad68-d16ef1ce99db@pavinjoseph.com/
Since d794734c9b was also marked for -stable, let's back it out before
causing more damage.
Note that due to another upstream change the revert was not 100% automatic:
0a845e0f63 mm/treewide: replace pud_large() with pud_leaf()
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Russ Anderson <rja@hpe.com>
Cc: Steve Wahl <steve.wahl@hpe.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/3a1b9909-45ac-4f97-ad68-d16ef1ce99db@pavinjoseph.com/
Fixes: d794734c9b ("x86/mm/ident_map: Use gbpages only where full GB page should be mapped.")
DT schema expects certain node names, as pointed out but dtbs_check:
exynos4412-smdk4412.dtb: keypad@100a0000: 'key-A', 'key-B', 'key-C', 'key-D', 'key-E' do not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Link: https://lore.kernel.org/r/20240312183105.715735-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-smdk4412.dtb: keypad@100a0000: 'key-A', 'key-B', 'key-C', 'key-D', 'key-E', 'linux,keypad-no-autorepeat' do not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: c9b92dd701 ("ARM: dts: Add keypad entries to SMDK4412")
Link: https://lore.kernel.org/r/20240312183105.715735-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-origen.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: bd08f6277e ("ARM: dts: Add keypad entries to Exynos4412 based Origen")
Link: https://lore.kernel.org/r/20240312183105.715735-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4210-smdkv310.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: 0561ceabd0 ("ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN")
Link: https://lore.kernel.org/r/20240312183105.715735-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Sparse warns:
drivers/net/wireless/ath/ath9k/eeprom_9287.c:82:9: warning: cast to restricted __le16
drivers/net/wireless/ath/ath9k/eeprom_9287.c:82:9: warning: cast from restricted __le32
drivers/net/wireless/ath/ath9k/eeprom_9287.c:83:9: warning: cast to restricted __le16
drivers/net/wireless/ath/ath9k/eeprom_9287.c:83:9: warning: cast from restricted __le32
drivers/net/wireless/ath/ath9k/eeprom_def.c:138:9: warning: cast to restricted __le16
drivers/net/wireless/ath/ath9k/eeprom_def.c:138:9: warning: cast from restricted __le32
drivers/net/wireless/ath/ath9k/eeprom_def.c:139:9: warning: cast to restricted __le16
drivers/net/wireless/ath/ath9k/eeprom_def.c:139:9: warning: cast from restricted __le32
drivers/net/wireless/ath/ath9k/eeprom_def.c:140:9: warning: cast to restricted __le16
drivers/net/wireless/ath/ath9k/eeprom_def.c:140:9: warning: cast from restricted __le32
drivers/net/wireless/ath/ath9k/eeprom_4k.c:79:9: warning: cast to restricted __le16
drivers/net/wireless/ath/ath9k/eeprom_4k.c:79:9: warning: cast from restricted __le32
antCtrlChain is an array of __le32 so le32_to_cpu() needs to be used.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://msgid.link/20240320170656.3534265-4-kvalo@kernel.org
Sparse warns:
drivers/net/wireless/ath/ath9k/init.c:79:5: warning: symbol 'ath9k_use_msi' was not declared. Should it be static?
Move the extern to ath9k.h so that it's visible in init.c.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://msgid.link/20240320170656.3534265-3-kvalo@kernel.org
Sparse warns:
drivers/net/wireless/ath/ath9k/xmit.c:1677:20: warning: incorrect type in initializer (different base types)
drivers/net/wireless/ath/ath9k/xmit.c:1677:20: expected unsigned short [usertype] mask
drivers/net/wireless/ath/ath9k/xmit.c:1677:20: got restricted __le16 [usertype]
drivers/net/wireless/ath/ath9k/xmit.c:1681:17: warning: restricted __le16 degrades to integer
drivers/net/wireless/ath/ath9k/xmit.c:1682:42: warning: restricted __le16 degrades to integer
drivers/net/wireless/ath/ath9k/xmit.c:1682:36: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/xmit.c:1682:36: expected restricted __le16 [usertype] frame_control
drivers/net/wireless/ath/ath9k/xmit.c:1682:36: got int
Fix ath9k_set_moredata() to use __le16 with masks and use if statement instead
of multiply operator.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://msgid.link/20240320170656.3534265-2-kvalo@kernel.org
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Sparse warns:
drivers/net/wireless/ath/wil6210/fw.c: note: in included file (through drivers/net/wireless/ath/wil6210/wil6210.h):
drivers/net/wireless/ath/wil6210/fw.h:96:47: warning: array of flexible structures
drivers/net/wireless/ath/wil6210/cfg80211.c: note: in included file (through drivers/net/wireless/ath/wil6210/wil6210.h):
drivers/net/wireless/ath/wil6210/fw.h:96:47: warning: array of flexible structures
I decided to remove the combos field altogether and just do pointer arithmetic
instead. Not pretty but I didn't want to waste too much time on an orphaned
driver.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320182449.3757215-5-kvalo@kernel.org
Sparse warns:
drivers/net/wireless/ath/wcn36xx/main.c:758:58: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/wcn36xx/main.c:758:58: expected unsigned short [usertype] vht_rx_mcs_map
drivers/net/wireless/ath/wcn36xx/main.c:758:58: got restricted __le16 [usertype] rx_mcs_map
drivers/net/wireless/ath/wcn36xx/main.c:760:58: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/wcn36xx/main.c:760:58: expected unsigned short [usertype] vht_tx_mcs_map
drivers/net/wireless/ath/wcn36xx/main.c:760:58: got restricted __le16 [usertype] tx_mcs_map
le16_to_cpu() was just missing. Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320182449.3757215-4-kvalo@kernel.org
Sparse warns:
drivers/net/wireless/ath/wcn36xx/txrx.c: note: in included file (through drivers/net/wireless/ath/wcn36xx/txrx.h):
drivers/net/wireless/ath/wcn36xx/wcn36xx.h:107:24: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/wcn36xx/wcn36xx.h:107:24: expected unsigned int [usertype]
drivers/net/wireless/ath/wcn36xx/wcn36xx.h:107:24: got restricted __be32 [usertype]
drivers/net/wireless/ath/wcn36xx/wcn36xx.h:107:24: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/wcn36xx/wcn36xx.h:107:24: expected unsigned int [usertype]
drivers/net/wireless/ath/wcn36xx/wcn36xx.h:107:24: got restricted __be32 [usertype]
Use void pointers and two separate variables to workaround the warning. Also
now the callers don't need any casting. There's actually cpu_to_be32_array()
available but decided to do minimal changes instead.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320182449.3757215-3-kvalo@kernel.org
Sparse warns:
drivers/net/wireless/ath/ath6kl/htc_pipe.c:241:17: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath6kl/htc_pipe.c:241:17: expected restricted __le16 x
drivers/net/wireless/ath/ath6kl/htc_pipe.c:241:17: got unsigned short [usertype]
drivers/net/wireless/ath/ath6kl/htc_mbox.c:368:9: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath6kl/htc_mbox.c:368:9: expected restricted __le16 x
drivers/net/wireless/ath/ath6kl/htc_mbox.c:368:9: got unsigned short [usertype]
Use put_unaligned_le16() so that the value is converted to little endian before
storing it to the header.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320182449.3757215-2-kvalo@kernel.org
The bindings header for Samsung pin controller DTS pin values (holding
register values in fact) was deprecated in v6.1 kernel in
commit 9d92925768 ("dt-bindings: pinctrl: samsung: deprecate header
with register constants"). This was enough of time for users to switch
to in-DTS headers, so drop the bindings header.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240312164428.692552-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() will be converted as weel if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
CC: Kalle Valo <kvalo@kernel.org>
CC: Jeff Johnson <jjohnson@kernel.org>
CC: linux-wireless@vger.kernel.org
CC: ath11k@lists.infradead.org
CC: ath10k@lists.infradead.org
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240315055211.1347548-1-lizhijian@fujitsu.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmYAlq0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGYqwH/0fb4pRbVtULpiIK
Cs7/e/IWzRRWLBq+Jj2KVVTxwjyiKFNOq6K/CHHnljIWo1yN2CIWeOgbHfTI0WfN
xmBdJP7OtK8MCN9PwwoWhZxMLcyv4pFCERrrkGa7AD+cdN4j/ytQ3mH5V8f/21fd
rnpQSdpgGXB2SSMHd520Y+e56+gxrrTmsDXjZWM08Wt0bbqAWJrjNe58BMz5hI1t
yQtcgYRTdUuZBn5TMkT99lK9EFQslV38YCo7RUP5D0DWXS1jSfWlgnCD1Nc1ziF4
ps/xPdUMDJAc5Tslg/hgJOciSuLqgMzIUsVgZrKysuu3NhwDY1LDWGORmH1t8E8W
RC25950=
=F+01
-----END PGP SIGNATURE-----
Merge tag 'v6.9-rc1' into sched/core, to pick up fixes and to refresh the branch
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The array size calculation in pvr_vm_mips_fini() appears to be incorrect based on
taking the size of the pointer rather than the size of the array, which manifests
as a warning about signed integer overflow:
In file included from include/linux/kernel.h:16,
from drivers/gpu/drm/imagination/pvr_rogue_fwif.h:10,
from drivers/gpu/drm/imagination/pvr_ccb.h:7,
from drivers/gpu/drm/imagination/pvr_device.h:7,
from drivers/gpu/drm/imagination/pvr_vm_mips.c:4:
drivers/gpu/drm/imagination/pvr_vm_mips.c: In function 'pvr_vm_mips_fini':
include/linux/array_size.h:11:25: error: overflow in conversion from 'long unsigned int' to 'int' changes value from '18446744073709551615' to '-1' [-Werror=overflow]
11 | #define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]) + __must_be_array(arr))
| ^
drivers/gpu/drm/imagination/pvr_vm_mips.c:106:24: note: in expansion of macro 'ARRAY_SIZE'
106 | for (page_nr = ARRAY_SIZE(mips_data->pt_pages) - 1; page_nr >= 0; page_nr--) {
| ^~~~~~~~~~
Just use the number of array elements directly here, and in the corresponding
init function for consistency.
Fixes: 927f3e0253 ("drm/imagination: Implement MIPS firmware processor and MMU support")
Reviewed-by: Donald Robson <donald.robson@imgtec.com>
Link: https://lore.kernel.org/lkml/9df9e4f87727399928c068dbbf614c9895ae15f9.camel@imgtec.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
The function hynix_nand_rr_init() should probably return an error code.
Judging by the usage, it seems that the return code is passed up
the call stack.
Right now, it always returns 0 and the function hynix_nand_cleanup()
in hynix_nand_init() has never been called.
Found by RASU JSC and Linux Verification Center (linuxtesting.org)
Fixes: 626994e074 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs")
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240313102721.1991299-1-korotkov.maxim.s@gmail.com
Sometimes, writes fail because the tWB_max is not correctly observed
after sending PAGEPROG. It leads to the R/B pin to be read as in
the "ready" state right after sending the command, thus preventing the
normal tPROG delay to be actually observed. This happens because the
ndelay() that waits for tWB_max starts before the command reaches the
NAND chip.
Add a dummy read when a delay is requested at the end of the executed
instruction to make sure that the sent command is received by the NAND
before starting the short ndelay() (<1us but rounded up to 1us in
practice). This read is done on the control register area because
doing it on the Async Data area would change the NAND's RE pin state.
This is not perfect as the two areas are behind two different
devm_ioremap_resource() and could possibly be located on different
interconnects (I did not find more details). This means either the
additional latency due to the load operation is enough impacting, or it
has the expected behavior of ensuring the write has been received.
This has been tested on two platforms designed off of the
DAVINCI/OMAP-L138. The first uses a Toshiba NAND Flash (TC58NYG2S3EBAI5),
the other a Macronix one (MX30UF4G18AC).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240308074609.9056-1-bastien.curutchet@bootlin.com
The value of an arithmetic expression directory * master->erasesize is
subject to overflow due to a failure to cast operands to a larger data
type before perfroming arithmetic
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Denis Arefev <arefev@swemel.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240315093758.20790-1-arefev@swemel.ru
Currently, the LBR code assumes that LBR Freeze is supported on all processors
when X86_FEATURE_AMD_LBR_V2 is available i.e. CPUID leaf 0x80000022[EAX]
bit 1 is set. This is incorrect as the availability of the feature is
additionally dependent on CPUID leaf 0x80000022[EAX] bit 2 being set,
which may not be set for all Zen 4 processors.
Define a new feature bit for LBR and PMC freeze and set the freeze enable bit
(FLBRI) in DebugCtl (MSR 0x1d9) conditionally.
It should still be possible to use LBR without freeze for profile-guided
optimization of user programs by using an user-only branch filter during
profiling. When the user-only filter is enabled, branches are no longer
recorded after the transition to CPL 0 upon PMI arrival. When branch
entries are read in the PMI handler, the branch stack does not change.
E.g.
$ perf record -j any,u -e ex_ret_brn_tkn ./workload
Since the feature bit is visible under flags in /proc/cpuinfo, it can be
used to determine the feasibility of use-cases which require LBR Freeze
to be supported by the hardware such as profile-guided optimization of
kernels.
Fixes: ca5b7c0d96 ("perf/x86/amd/lbr: Add LbrExtV2 branch record support")
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/69a453c97cfd11c6f2584b19f937fe6df741510f.1711091584.git.sandipan.das@amd.com
SCMI raw debugfs entries are used to inject and snoop messages out of the
SCMI core and, as such, the underlying virtual files have no reason to
support seeking.
Modify the related file_operations descriptors to be non-seekable.
Fixes: 3c3d818a93 ("firmware: arm_scmi: Add core raw transmission support")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240315140324.231830-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fastchannels are initialized with an incorrect index(POWERCAP_PAI_GET) in:
commit 2441caa84a ("firmware: arm_scmi: Populate fast channel rate_limit")
Fix this and provide a correct index(POWERCAP_FC_PAI)
Fixes: 2441caa84a ("firmware: arm_scmi: Populate fast channel rate_limit")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202403100744.7Op3PI8L-lkp@intel.com/
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Link: https://lore.kernel.org/r/20240311090413.1710725-1-pierre.gondois@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
FFA_NOTIFICATION_INFO_GET retrieves information about pending
notifications. Notifications can be either global or per VCPU. Global
notifications are reported with the partition ID only in the list of
endpoints with pending notifications. ffa_notification_info_get()
incorrectly expect no ID at all for global notifications. Fix this by
checking for ID = 1 instead of ID = 0.
Fixes: 3522be48d8 ("firmware: arm_ffa: Implement the NOTIFICATION_INFO_GET interface")
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20240311110700.2367142-1-jens.wiklander@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Handle the case where -EOPNOTSUPP is returned from OTP driver.
This addresses an issue that occurs with the Intel SPI flash controller,
which has a limited supported opcode set. Whilst the OTP functionality
is not available due to this restriction, other parts of the MTD
functionality of the device are intact. This change allows the driver
to gracefully handle the restriction by allowing the supported
functionality to remain available instead of failing the probe
altogether.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240313173425.1325790-3-aapo.vienamo@linux.intel.com
Jump to the error reporting code in mtd_otp_nvmem_add() if the
mtd_otp_size() call fails. Without this fix, the error is not logged.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240313173425.1325790-2-aapo.vienamo@linux.intel.com
Convert the imx-pata bindings to DT schema.
Add missing fsl,imx31-pata and fsl,imx51-pata compatibles during
conversion, because they are already being used in existing DTS.
Signed-off-by: Animesh Agarwal <animeshagarwal28@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Per filesystems/sysfs.rst, show() should only use sysfs_emit()
or sysfs_emit_at() when formatting the value to be returned to user space.
coccinelle complains that there are still a couple of functions that use
snprintf(). Convert them to sysfs_emit().
sprintf() will be converted as weel if they have.
Generally, this patch is generated by
make coccicheck M=<path/to/file> MODE=patch \
COCCI=scripts/coccinelle/api/device_attr_show.cocci
No functional change intended
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Since commit 43a7206b09 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the lirc_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Unify the indentation and multi-line comment style.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Remove trailing comma in the terminator entry in ID table(s).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
We have a temporary variable to keep pointer to struct device.
Utilise it inside the ->probe() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Update header inclusions to follow IWYU (Include What You Use)
principle.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The function descriptions where falsely copy pasted from another entry,
write more fitting descriptions for the functions.
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Multiple issues detected while scanning the code by far not a complete
list of required changes but some small improvements.
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Correct multiple different typos found in comments or function names.
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add support for starting a polling timer in case an interrupt is not
available. This helps to keep the VPU functional in SoCs such as AM62A,
where the hardware interrupt hookup may not be present due to an SoC errata
[1].
The timer is shared across all instances of encoders and decoders and is
started when the first instance of an encoder or decoder is opened and
stopped when the last instance is closed, thus avoiding per instance
polling and saving CPU bandwidth. As VPU driver manages this instance
related tracking and synchronization, the aforementioned shared timer
related polling logic is implemented within the VPU driver itself. This
scheme may also be useful in general too (even if irq is present) for
non-realtime multi-instance VPU use-cases (for e.g 32 instances of VPU
being run together) where system is running already under high interrupt
load and switching to polling may help mitigate this as the polling thread
is shared across all the VPU instances.
Hrtimer is chosen for polling here as it provides precise timing and
scheduling and the API seems better suited for periodic polling task such
as this. As a general rule of thumb,
Worst case latency with hrtimer = Actual latency (achievable with irq)
+ Polling interval
NOTE (the meaning of terms used above is as follows):
- Latency: Time taken to process one frame
- Actual Latency : Time taken by hardware to process one frame and signal
it to OS (i.e. if latency that was possible to achieve if irq line was
present)
There is a trade-off between latency and CPU usage when deciding the value
for polling interval. With aggressive polling intervals (i.e. going with
even lesser values) the CPU usage increases although worst case latencies
get better. On the contrary, with greater polling intervals worst case
latencies will increase although the CPU usage will decrease.
The 5ms offered a good balance between the two as we were able to reach
close to actual latencies (as achievable with irq) without incurring too
much of CPU as seen in below experiments and thus 5ms is chosen as default
polling interval.
- 1x 640x480@25 Encoding using different hrtimer polling intervals [2]
- 4x 1080p30 Transcode (File->decode->encode->file) irq vs polling
comparison [3]
- 1x 1080p Transcode (File->decode->encode->file) irq vs polling comparison
[4]
- 1080p60 Streaming use-case irq vs polling comparison [5]
- 1x 1080p30 sanity decode and encode tests [6]
The polling interval can also be changed using vpu_poll_interval module
param in case user want to change it as per their use-case requirement
keeping in mind above trade-off.
Parse the irq number and if not present, initialize the hrtimer and the
polling worker thread before proceeding with v4l2 device registrations.
Based on interrupt status, we use a worker thread to iterate over the
interrupt status for each instance and send completion event as being done
in irq thread function.
Move the core functionality of the irq thread function to a separate
function wave5_vpu_handle_irq so that it can be used by both the worker
thread when using polling mode and irq thread when using interrupt mode.
Protect the hrtimer access and instance list with device specific mutex
locks to avoid race conditions while different instances of encoder and
decoder are started together.
[1] https://www.ti.com/lit/pdf/spruj16
(Ref: Section 4.2.3.3 Resets, Interrupts, and Clocks)
[2] https://gist.github.com/devarsht/ee9664d3403d1212ef477a027b71896c
[3] https://gist.github.com/devarsht/3a58b4f201430dfc61697c7e224e74c2
[4] https://gist.github.com/devarsht/a6480f1f2cbdf8dd694d698309d81fb0
[5] https://gist.github.com/devarsht/44aaa4322454e85e01a8d65ac47c5edb
[6] https://gist.github.com/devarsht/2f956bcc6152dba728ce08cebdcebe1d
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Jackson Lee <jackson.lee@chipsnmedia.com>
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>