The serial node does not use/allow address/size cells:
qdu1000-idp.dtb: geniqup@9c0000: serial@99c000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
Fixes: 6bd20c54b5 ("arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308125906.236885-3-krzysztof.kozlowski@linaro.org
There is only one output port, thus out-ports should not have
'address/size-cells' and unit addresses. 'reg-names' are also not
allowed by bindings.
qrb5165-rb5.dtb: funnel@6042000: out-ports: '#address-cells', '#size-cells', 'port@0' do not match any of the regexes: 'pinctrl-[0-9]+'
qrb5165-rb5.dtb: funnel@6b04000: Unevaluated properties are not allowed ('reg-names' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308125906.236885-2-krzysztof.kozlowski@linaro.org
The SPMI controller (PMIC Arbiter)) does not use nor allow 'cell-index'
property:
sm8150-microsoft-surface-duo.dtb: spmi@c440000: Unevaluated properties are not allowed ('cell-index' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308125906.236885-1-krzysztof.kozlowski@linaro.org
It goes without saying that socname_rpmpds[] is the array of the RPM
power domains associated with socname. Remove these comments.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-10-06a4f448ff90@linaro.org
The GPU core clock requires that both VDDGX and VDDMX domains are scaled
at the same rate at the same time (well, MX just before GX but you get
the idea). Set MX as parent of GX to take care of that.
Suggested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-9-06a4f448ff90@linaro.org
In some cases (like with the GPU core clock on GMU-less SoCs) it's
required that we scale more than one voltage domain. This can be achieved
by linking them in a parent-child relationship. Add support for specifying
a parent PD, similarly to what has been done in the RPMhPD driver.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-8-06a4f448ff90@linaro.org
Currently the whitespace between [DT_BINDING] = &struct is all over
the place.. some SoC structs have a space, others have a tab, others
have N tabs.. Make that a single tab for everybody to keep things
coherent.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-7-06a4f448ff90@linaro.org
Now that we aren't bound by the preprocessor macros, improve the naming
to be a bit less preprocessor-y and touch up some rpmpd.pd.name fields
while at it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-6-06a4f448ff90@linaro.org
Expand the struct definition macros to make things easier to see and
maintain. Now that the macros are unnecessary, remove them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-5-06a4f448ff90@linaro.org
It's rather obvious by the characteristic of these resources that
they correspond to some voltage lines governed by RPM. Remove the
"vdd" unnecessary prefix from them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-4-06a4f448ff90@linaro.org
Up until now, we had 2 separate entries for VDD_LPI[CM]X and
VDD_LPI_[CM]X which both pointed to the same RPM resource. Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-3-06a4f448ff90@linaro.org
Replace the SoC names with type+id_key (or type+id+..name..+key for
fixed-key definitions) and remove duplicate entries.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-rpmpd-v3-1-06a4f448ff90@linaro.org
gcc with W=1 reports these errors
drivers/clk/qcom/gpucc-sm6375.c:145:37: error:
‘gpucc_parent_data_2’ defined but not used [-Werror=unused-const-variable=]
145 | static const struct clk_parent_data gpucc_parent_data_2[] = {
| ^~~~~~~~~~~~~~~~~~~
drivers/clk/qcom/gpucc-sm6375.c:139:32: error:
‘gpucc_parent_map_2’ defined but not used [-Werror=unused-const-variable=]
139 | static const struct parent_map gpucc_parent_map_2[] = {
| ^~~~~~~~~~~~~~~~~~
These variables are not used, so remove them.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315155630.1740065-1-trix@redhat.com
Add the PARENT_ENABLE flag to prevent the clock from getting stuck
at boot and use floor_ops to avoid SDHCI overclocking.
Fixes: 496d1a13d4 ("clk: qcom: Add Global Clock Controller driver for QCM2290")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315173048.3497655-1-konrad.dybcio@linaro.org
There's a typo in the @<address> part of the uart9 label. Fix it.
Fixes: 10d900a834 ("arm64: dts: sm8150: add the QUPv3 high-speed UART node")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315202751.1518543-1-brgl@bgdev.pl
Add the ID for the Qualcomm SM7150 SoC.
Signed-off-by: David Wronek <davidwronek@gmail.com>
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230305191745.386862-2-danila@jiaxyga.com
UML supports HAS_IOMEM since 0bbadafdc4 (um: allow disabling
NO_IOMEM).
Current IMA build on UML fails on allmodconfig (with TCG_TPM=m):
ld: security/integrity/ima/ima_queue.o: in function `ima_add_template_entry':
ima_queue.c:(.text+0x2d9): undefined reference to `tpm_pcr_extend'
ld: security/integrity/ima/ima_init.o: in function `ima_init':
ima_init.c:(.init.text+0x43f): undefined reference to `tpm_default_chip'
ld: security/integrity/ima/ima_crypto.o: in function `ima_calc_boot_aggregate_tfm':
ima_crypto.c:(.text+0x1044): undefined reference to `tpm_pcr_read'
ld: ima_crypto.c:(.text+0x10d8): undefined reference to `tpm_pcr_read'
Modify the IMA Kconfig entry so that it selects TCG_TPM if HAS_IOMEM
is set, regardless of the UML Kconfig setting.
This updates TCG_TPM from =m to =y and fixes the linker errors.
Fixes: f4a0391dfa ("ima: fix Kconfig dependencies")
Cc: Stable <stable@vger.kernel.org> # v5.14+
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-um@lists.infradead.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Handle case when module is unloaded (kfd_exit) before a process space
(mm_struct) is released.
v2: Fixed potential race conditions by removing all kfd_process from
the process table first, then working on releasing the resources.
v3: Fixed loop element access / synchronization. Fixed extra empty lines.
Signed-off-by: David Belanger <david.belanger@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As a temporary storage, staged_config[] in rdt_domain should be cleared
before and after it is used. The stale value in staged_config[] could
cause an MSR access error.
Here is a reproducer on a system with 16 usable CLOSIDs for a 15-way L3
Cache (MBA should be disabled if the number of CLOSIDs for MB is less than
16.) :
mount -t resctrl resctrl -o cdp /sys/fs/resctrl
mkdir /sys/fs/resctrl/p{1..7}
umount /sys/fs/resctrl/
mount -t resctrl resctrl /sys/fs/resctrl
mkdir /sys/fs/resctrl/p{1..8}
An error occurs when creating resource group named p8:
unchecked MSR access error: WRMSR to 0xca0 (tried to write 0x00000000000007ff) at rIP: 0xffffffff82249142 (cat_wrmsr+0x32/0x60)
Call Trace:
<IRQ>
__flush_smp_call_function_queue+0x11d/0x170
__sysvec_call_function+0x24/0xd0
sysvec_call_function+0x89/0xc0
</IRQ>
<TASK>
asm_sysvec_call_function+0x16/0x20
When creating a new resource control group, hardware will be configured
by the following process:
rdtgroup_mkdir()
rdtgroup_mkdir_ctrl_mon()
rdtgroup_init_alloc()
resctrl_arch_update_domains()
resctrl_arch_update_domains() iterates and updates all resctrl_conf_type
whose have_new_ctrl is true. Since staged_config[] holds the same values as
when CDP was enabled, it will continue to update the CDP_CODE and CDP_DATA
configurations. When group p8 is created, get_config_index() called in
resctrl_arch_update_domains() will return 16 and 17 as the CLOSIDs for
CDP_CODE and CDP_DATA, which will be translated to an invalid register -
0xca0 in this scenario.
Fix it by clearing staged_config[] before and after it is used.
[reinette: re-order commit tags]
Fixes: 75408e4350 ("x86/resctrl: Allow different CODE/DATA configurations to be staged")
Suggested-by: Xin Hao <xhao@linux.alibaba.com>
Signed-off-by: Shawn Wang <shawnwang@linux.alibaba.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/2fad13f49fbe89687fc40e9a5a61f23a28d1507a.1673988935.git.reinette.chatre%40intel.com
[Why]
Framedrops are observed while playing Vp9 and Av1 10 bit
video on 8k resolution using VSR while playback controls
are disappeared/appeared
[How]
Now ODM 2 to 1 is disabled for 5k or greater resolutions on VSR.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Ayush Gupta <ayugupta@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In USB4 DP tunneling, it's possible to have this scenario that
the path becomes unavailable and CM tears down the path a little bit late.
So, in this case, the HPD is high but fails to read any DPCD register.
That causes the link connection type to be set to sst.
And not all sinks are removed behind the MST branch.
[How]
Restore the link connection type if it fails to read DPCD register.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Writing to DRR registers such as OTG_V_TOTAL_MIN on the same frame as a
pipe commit can cause underflow.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
On SM6350, there is only one LLCC bank available. So let's just pass that
as "llcc0_base".
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-12-manivannan.sadhasivam@linaro.org
[WHY]
Hot plugging and then hot unplugging leads to k1 and k2 values to
change, as signal is detected as a virtual signal on hot unplug. Writing
these values to OTG_PIXEL_RATE_DIV register might cause primary display
to blank (known hw bug).
[HOW]
No longer write k1 and k2 values to register if signal is virtual, we
have safe guards in place in the case that k1 and k2 is unassigned so
that an unknown value is not written to the register either.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-11-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-10-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-9-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-8-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org> # Thinkpad X13s
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-7-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
While at it, let's also fix the size of the llcc_broadcast_base to cover
the whole region.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-6-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
On SC7180, there is only one LLCC bank available. So let's just pass that
as "llcc0_base".
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-5-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
On SDM845, the size of the LLCC bank 0 needs to be reduced to 0x4500 as
there are LLCC BWMON registers located after this range.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-4-manivannan.sadhasivam@linaro.org
The platforms based on SDM845 SoC locks the access to EDAC registers in the
bootloader. So probing the EDAC driver will result in a crash. Hence,
disable the creation of EDAC platform device on all SDM845 devices.
The issue has been observed on Lenovo Yoga C630 and DB845c.
While at it, also sort the members of `struct qcom_llcc_config` to avoid
any holes in-between.
Cc: <stable@vger.kernel.org> # 5.10
Reported-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-15-manivannan.sadhasivam@linaro.org
Not all Qcom platforms support IRQ mode for ECC handling. For those
platforms, the current EDAC driver will not be probed due to missing ECC
IRQ in devicetree.
So add support for polling mode so that the EDAC driver can be used on all
Qcom platforms supporting LLCC.
The polling delay of 5000ms is chosen based on Qcom downstream/vendor
driver.
Reported-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Steev Klimaszewski <steev@kali.org> # Thinkpad X13s
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-14-manivannan.sadhasivam@linaro.org
The Qualcomm LLCC/EDAC drivers were using a fixed register stride for
accessing the (Control and Status Registers) CSRs of each LLCC bank.
This stride only works for some SoCs like SDM845 for which driver
support was initially added.
But the later SoCs use different register stride that vary between the
banks with holes in-between. So it is not possible to use a single register
stride for accessing the CSRs of each bank. By doing so could result in a
crash.
For fixing this issue, let's obtain the base address of each LLCC bank from
devicetree and get rid of the fixed stride. This also means, there is no
need to rely on reg-names property and the base addresses can be obtained
using the index.
First index is LLCC bank 0 and last index is LLCC broadcast. If the SoC
supports more than one bank, then those need to be defined in devicetree
for index from 1..N-1.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Steev Klimaszewski <steev@kali.org> # Thinkpad X13s
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-13-manivannan.sadhasivam@linaro.org
Register regions of the LLCC banks are located at different addresses.
Currently, the binding just lists the LLCC0 base address and tries to
cover all the banks using a single size. This is entirely wrong as there
are other register regions that happen to lie inside the size covered by
the binding such as the memory controller and holes.
So this needs to be fixed by specifying the base address of individual
LLCC banks. This approach will break the existing users of this binding
as the register regions are split and the drivers now cannot use
LLCC0 register region for accessing rest of the banks (which is wrong
anyway).
But considering the fact that the binding was wrong from the day one and
also the device drivers going wrong by the binding, this breakage is
acceptable.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-3-manivannan.sadhasivam@linaro.org
Both Rishabh and Sai have left Qualcomm, and there is no evidence of them
maintaining with a new identity. So their entry needs to be removed.
Listed Bjorn as the interim maintainer until someone volunteers to maintain
this binding.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-2-manivannan.sadhasivam@linaro.org
ppc_md.calibrate_decr() is a mandatory item. Its nullity is never
checked so it must be non null on all platforms.
Most platforms define generic_calibrate_decr() as their
ppc_md.calibrate_decr(). Have time_init() call
generic_calibrate_decr() when ppc_md.calibrate_decr() is NULL,
and remove default assignment from all machines.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/6cb9865d916231c38401ba34ad1a98c249fae135.1676711562.git.christophe.leroy@csgroup.eu
This machine matches two compatibles and sets .pci_irq_fixup
on one of them.
Split it into two machines, then the probe function can be dropped.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Drop references to ppc47x_probe() to fix build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/6cb9865d916231c38401ba34ad1a98c249fae135.1676711562.git.christophe.leroy@csgroup.eu
