Adds status interface for zynqmp-fpga. It's a read only interface
which allows the user to get the Programmable Logic(PL) configuration
status.
Usage:
To read the Programmable Logic(PL) configuration status.
cat /sys/bus/platform/drivers/zynqmp_fpga_manager/firmware:zynqmp-firmware:pcap/status
Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20230224120738.329416-3-nava.kishore.manne@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds PM API for performing Programmable Logic(PL) configuration
register readback. It provides an interface to the firmware(pmufw)
to readback the FPGA configuration register.
Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20230224120738.329416-2-nava.kishore.manne@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230307202435.880921-1-helgaas@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"priv->ext_config_dev_aspm" was never set to a non-zero value. Therefore,
alcor_pci_aspm_ctrl(priv, 1) did nothing, and alcor_pci_aspm_ctrl(priv, 0)
always disabled ASPM in the device and the upstream bridge.
The driver disabled ASPM in alcor_pci_probe() and alcor_resume(), so it's
possible the device doesn't work well when ASPM is enabled.
Remove all the ASPM-related code and replace the alcor_pci_aspm_ctrl(0)
calls with pci_disable_link_state(pdev, PCIE_LINK_STATE_L0S |
PCIE_LINK_STATE_L1), which asks the PCI core to disable ASPM.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20230307213816.886308-1-helgaas@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although this driver is a good use case for having a directory
that is not other directories and then subdirectories with more
entries, the usage of register_sysctl_table() can recurse and
increases complexity so to avoid that just split out the
registration to each directory with its own entries.
register_sysctl_table() is a deprecated compatibility wrapper.
register_sysctl() can do the directory creation for you so just use
that.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lore.kernel.org/r/20230302204612.782387-6-mcgrof@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code tries to get an associated clk, ignores any errors in the
process and if there is a clock enables it unconditionally for the whole
lifetime of the sram device.
Instead use an "optional" variant of devm_clk_get() which handles the case
where no clk is needed for the sram device and do proper error handling
for the remaining error cases. Also use an "enabled" variant of
devm_clk_get() to simplify. With that .probe() is the only function using
struct sram_dev::clk, so it can be replaced by a local variable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20230302091251.1852454-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definitions to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20230227-kobj_type-firmware-dmi-v1-1-d1131d4e7a2b@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These char PCMCIA drivers are buggy[1] and receive only minimal care. It
was concluded[2], that we should try to remove most pcmcia drivers
completely. Let's start with these char broken one.
Note that I also removed a UAPI header: include/uapi/linux/cm4000_cs.h.
I found only coccinelle tests mentioning some ioctl constants from that
file. But they are not actually used. Anyway, should someone complain,
we may reintroduce the header (or its parts).
[1] https://lore.kernel.org/all/f41c2765-80e0-48bc-b1e4-8cfd3230fd4a@www.fastmail.com/
[2] https://lore.kernel.org/all/c5b39544-a4fb-4796-a046-0b9be9853787@app.fastmail.com/
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: "Hyunwoo Kim" <imv4bel@gmail.com>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230222092302.6348-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipwireless' Kconfig entry is currently sitting in char/pcmcia. But
the driver is in tty/. So move the entry to tty/ too.
First, it makes sense to have the entry along the driver. Second, whole
char/pcmcia is about to pass away.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20230222092302.6348-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the bogus uart_write_wakeup() from when setting up a new DMA
transfer, which does not free up any more space in the ring buffer.
Any pending writers will be woken up when the transfer completes.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that there is data in the ring buffer before trying to set up
a zero-length DMA transfer.
This specifically fixes the following warning when unmapping the empty
buffer on the sc8280xp-crd:
WARNING: CPU: 0 PID: 138 at drivers/iommu/dma-iommu.c:1046 iommu_dma_unmap_page+0xbc/0xd8
...
Call trace:
iommu_dma_unmap_page+0xbc/0xd8
dma_unmap_page_attrs+0x30/0x1c8
geni_se_tx_dma_unprep+0x28/0x38
qcom_geni_serial_isr+0x358/0x75c
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix what appears to be a copy-paste error that can lead to a leaked DMA
mapping on close() and failure to restart TX after the port is reopened.
Note that rx_dma_addr is generally NULL when
qcom_geni_serial_stop_tx_dma() is called as part of shutdown() (but
tx_dma_addr need not be).
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit added back the calls top stop tx and rx to shutdown()
which had previously been removed by commit e83766334f ("tty: serial:
qcom_geni_serial: No need to stop tx/rx on UART shutdown") in order to
be able to use kgdb after stopping the getty.
Not only did this again break kgdb, but it also broke serial consoles
more generally by hanging TX when stopping the getty during reboot.
The underlying problem has been there since the driver was first merged
and fixing it is going to be a bit involved so simply stop calling the
broken stop functions during shutdown for consoles for now.
Fixes: d8aca2f968 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible for a file type to support uring commands, but not
pollable ones. Hence before issuing one of those, we should check
that it is supported and error out upfront if it isn't.
Cc: stable@vger.kernel.org
Fixes: 5756a3a7e7 ("io_uring: add iopoll infrastructure for io_uring_cmd")
Link: https://github.com/axboe/liburing/issues/816
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The console= kernel command-line parameter defines where the kernel
messages appear. It can be used multiple times to make the kernel log
visible on more devices.
The ordering of the console= parameters is important. In particular,
the last one defines which device can be accessed also via /dev/console.
The behavior is more complicated when the last console= parameter is
ignored by kernel. It might be surprising because it was not intentional.
The kernel just works this way historically.
There were few attempts to change the behavior. Unfortunately, it can't
be done because it would break existing users. Document the historical
behavior at least.
Link: https://lore.kernel.org/r/20170606143149.GB7604@pathway.suse.cz
Link: https://lore.kernel.org/r/20230213113912.1237943-1-rkanwal@rivosinc.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230308112433.24292-1-pmladek@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per RZ/V2M hardware manual(Rev.1.30 Jun, 2022), UART IP has a
restriction as mentioned below.
40.6.1 Point for Caution when Changing the Register Settings:
When changing the settings of the following registers, a PRESETn master
reset or FIFO reset + SW reset (FCR[2],FCR[1], HCR0[7]) must be input to
re-initialize them.
Target Registers: FCR, LCR, MCR, DLL, DLM, HCR0.
Add serial8250_em_reg_update() and serial8250_em_serial_out_helper() to
handle this restriction. serial8250_em_serial_out_helper() is identical to
previous serial8250_em_serial_out() except that UART_FCR macro is removed
from serial8250_em_serial_out_helper() as it is now handled by serial8250_
em_serial_out().
DLL/DLM register can be updated only by setting LCR[7]. So the
updation of LCR[7] will perform reset for DLL/DLM register changes.
EMMA mobile has the same register set as RZ/V2M and this patch is tested on
EMEV2 board. So, there is no harm in applying the same restriction here as
well as the HW manual for EMMA mobile is not updated for a long time.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-8-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART_FCR shares the same offset with UART_IIR. We cannot use UART_FCR
in serial8250_em_serial_in() as it overlaps with UART_IIR.
Define UART_FCR_EM macro with a high value to avoid overlapping
with existing UART_* register defines and define another macro
UART_FCR_EM_HW for the real offset.
Use these macros in serial8250_em_serial{_in/_out} function to
read/write FCR register.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-7-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify clk handling in probe() by replacing devm_clk_get()->devm_
clk_get_enabled(). This replaces the usage of clk_prepare_enable/clk_
disable_unprepare() in probe()/remove(). After that sclk is no
longer required in struct serial8250_em_priv and is replaced by a
local variable sclk in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify probe() by using dev_err_probe() instead of dev_err() and
add a local variable 'dev' to replace '&pdev->dev'.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch meson-12-common.dtsi to use the Meson G12A specific UART
compatible string. This enables the "divide XTAL by 2" divider which
improves support for UART attached Bluetooth modules (for example
RTL8822CS) running at a baud rate of 1500000. Without dividing XTAL
(24MHz) by 2 a baud rate of 1500000 cannot be generated cleanly and the
resulting jitter breaks communication with the module.
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230307222651.2106615-4-martin.blumenstingl@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amlogic Meson G12A (and later) SoCs also have the "divide XTAL by 2" bit
as the S4 UART controllers. Add a new compatible string for these SoCs
and enable the has_xtal_div2 flag for them.
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230307222651.2106615-3-martin.blumenstingl@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amlogic G12A SoCs gained a new "divide XTAL by 2" bit. Everything else
(we know about) is identical to the UART IP on GX (GXBB/GXL/GXM) SoCs.
Add a new compatible string for this SoC so this new bit can be managed
accordingly while keeping "amlogic,meson-gx-uart" as fallback compatible
string.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230307222651.2106615-2-martin.blumenstingl@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add binding description for mediatek,mt8365-uart
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230309143459.401783-3-bero@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stm32_usart_transmit_chars() may be called with empty or stopped
transmit queue, and no XON/OFF character pending. This can happen at
the end of transmission, where this last call is used to either handle
the XON/XOFF x_char, or disable TX interrupt if queue is empty or
stopped.
If that occurs, do not assert the RS485 RTS/DE GPIO anymore, as the
GPIO would remain asserted past the end of transmission and that would
block the RS485 bus after the transmission.
Only assert the RS485 RTS/DE GPIO if there is either pending XON/XOFF
x_char, or at least one character in running transmit queue.
Fixes: d7c7671616 ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230223042252.95480-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_sysctl_table() is a deprecated compatibility wrapper.
register_sysctl_init() can do the directory creation for you so just use
that
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230302204612.782387-7-mcgrof@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in casting a struct uart_port to a struct imx_port
just to access the first member of the latter (a struct uart_port).
This introduces no code changes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230302115417.1860210-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART IP must be connected to clock, document the properties in DT bindings.
Update example to match Linux arch/arm/boot/dts/imx51.dtsi .
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230219142250.10176-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART IP can be connected to DMA engine, document the properties in DT bindings.
Update example to match Linux arch/arm/boot/dts/imx51.dtsi .
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230219142250.10176-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The int variable ret does not receive the return value in this function.
It should be removed and returned 0 directly.
Signed-off-by: Li zeming <zeming@nfschina.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230222202303.3195-1-zeming@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From time to time DMA completion can come in the middle of DMA shutdown:
<process ctx>: <IRQ>:
lpuart32_shutdown()
lpuart_dma_shutdown()
del_timer_sync()
lpuart_dma_rx_complete()
lpuart_copy_rx_to_tty()
mod_timer()
lpuart_dma_rx_free()
When the timer fires a bit later, sport->dma_rx_desc is NULL:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
pc : lpuart_copy_rx_to_tty+0xcc/0x5bc
lr : lpuart_timer_func+0x1c/0x2c
Call trace:
lpuart_copy_rx_to_tty
lpuart_timer_func
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
__irq_exit_rcu
irq_exit
handle_domain_irq
gic_handle_irq
call_on_irq_stack
do_interrupt_handler
...
To fix this fold del_timer_sync() into lpuart_dma_rx_free() after
dmaengine_terminate_sync() to make sure timer will not be re-started in
lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().
Fixes: 4a8588a1cf ("serial: fsl_lpuart: delete timer on shutdown")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20230309134302.74940-2-alexander.sverdlin@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Fix up the two paths in the freescale callback that failed to re-enable
interrupts when polling.
Fixes: 853a9ae29e ("serial: 8250: fix handle_irq locking")
Cc: stable@vger.kernel.org # 5.13
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y/xYzqp4ogmOF5t0@kili
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230227085046.24282-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 8d310c9107 ("drivers/tty/serial/8250: Make Aspeed VUART SIRQ polarity configurable")
Cc: stable <stable@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Oskar Senft <osk@google.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-9-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230223093941.31790-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5779a072c2.
This results in a link error of
ld: drivers/tty/serial/earlycon.o: in function `parse_options':
drivers/tty/serial/earlycon.c:99: undefined reference to `uart_parse_earlycon'
When the config is in this state
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_FSL_LPUART=m
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
Fixes: 5779a072c2 ("tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency")
Cc: stable <stable@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230226173846.236691-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux/fs.h has a wrapper for this operation.
Signed-off-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230306075527.1338-1-zbestahu@gmail.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
When neither "no_read_workqueue" nor "no_write_workqueue" are enabled,
tasklet_trylock() in crypt_dec_pending() may still return false due to
an uninitialized state, and dm-crypt will unnecessarily do io completion
in io_queue workqueue instead of current context.
Fix this by adding an 'in_tasklet' flag to dm_crypt_io struct and
initialize it to false in crypt_io_init(). Set this flag to true in
kcryptd_queue_crypt() before calling tasklet_schedule(). If set
crypt_dec_pending() will punt io completion to a workqueue.
This also nicely avoids the tasklet_trylock/unlock hack when tasklets
aren't in use.
Fixes: 8e14f61015 ("dm crypt: do not call bio_endio() from the dm-crypt tasklet")
Cc: stable@vger.kernel.org
Reported-by: Hou Tao <houtao1@huawei.com>
Suggested-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
They are used during the erofs module init phase. Let's mark it as
__init like any other function.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230303063731.66760-1-frank.li@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
