Convert spi-st-ssc.txt into st,ssc-spi.yaml for the
ST Microelectronics SSC SPI driver.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230213192349.17101-1-avolmat@me.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Group some variables based on their sizes to reduce hole and avoid padding.
On x86_64, this shrinks the size from 144 to 128 bytes.
Turn 'timestamped' into a bitfield so that it can be easily merged with
some other bifields and move 'error'.
This should have no real impact on memory allocation because 'struct
spi_transfer' is mostly used on stack, but it can save a few cycles
when the structure is initialized or copied.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/93a051da85a895bc6003aedfb00a13e1c2fc6338.1676370870.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue where some flash chips like cypress S25HS256T return the
value of the same register over and over in DAC mode.
For example in the TI K3-AM62x Processors refer [0] Technical Reference
Manual there is a layer of digital logic in front of the QSPI/OSPI
Drive when used in DAC mode. This is part of the Flash Subsystem (FSS)
which provides access to external Flash devices.
The FSS0_0_SYSCONFIG Register (Offset = 4h) has a BIT Field for
OSPI_32B_DISABLE_MODE which has a Reset value = 0. This means, OSPI 32bit
mode enabled by default.
Thus, by default controller operates in 32 bit mode causing it to always
align all data to 4 bytes from a 4byte aligned address. In some flash
chips like cypress for example if we try to read some regs in DAC mode
then it keeps sending the value of the first register that was requested
and inorder to read the next reg, we have to stop and re-initiate a new
transaction.
This causes wrong register values to be read than what is desired when
registers are read in DAC mode. Hence if the data.nbytes is very less
then prefer STIG mode for such small reads.
[0] https://www.ti.com/lit/ug/spruiv7a/spruiv7a.pdf
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-5-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup the Addr bit field while issuing register reads in STIG mode. This
is needed for example flashes like cypress define in their transaction
table that to read any register there is 1 cmd byte and a few more address
bytes trailing the cmd byte. Absence of addr bytes will obviously fail
to read correct data from flash register that maybe requested by flash
driver because the controller doesn't even specify which address of the
flash register the read is being requested from.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-4-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Create new flag inorder to avoid playing with use_direct_mode
flag currently being used throughout the driver.
Disable DAC write if auto polling is disabled or CQSPI_DISABLE_DAC_MODE
is set.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-3-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If one leaves the CQSPI_REG_CMDCTRL in an unclean state this may cause
issues in future command reads. This issue came to light when some flash
reads in STIG mode were coming back dirty.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-2-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Group some bool variables to reduce hole and avoid padding.
On x86_64, this shrinks the size from 136 to 128 bytes.
As an example:
$ size drivers/base/regmap/regmap-fsi.o (Before)
text data bss dec hex filename
4837 136 0 4973 136d drivers/base/regmap/regmap-fsi.o
$ size drivers/base/regmap/regmap-fsi.o (After)
text data bss dec hex filename
4701 136 0 4837 12e5 drivers/base/regmap/regmap-fsi.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/077ca39622c8870a3ea932298a9cec34f7a8295a.1676363976.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify code by using min helper macro for logical evaluation and value
assignment. The change also facilitates code realignment for improved
readability.
Proposed change is identified using minmax.cocci Coccinelle script.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/Y+p2Hn0nrtHiKwPR@ubun2204.myguest.virtualbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel is globally removing the ambiguous 0-length and 1-element
arrays in favor of flexible arrays, so that we can gain both compile-time
and run-time array bounds checking[1]. In this instance, struct
skl_cpr_cfg contains struct skl_cpr_gtw_cfg, which defined "config_data"
as a 1-element array.
However, case present in sound/soc/intel/skylake/skl-topology.h is not a
simple one as the structure takes part in IPC communication. Apparently
original definition missed one field, which while not used by AudioDSP
firmware when there is no additional data, is still expected to be part
of an IPC message. Currently this works because of how 'config_data' is
declared: 'config_data[1]'. Now when one replaces it with a flexible
array there would be one field missing. Update struct declaration to fix
this.
Reported-by: Sasa Ostrouska <casaxa@gmail.com>
Link: https://lore.kernel.org/all/CALFERdwvq5day_sbDfiUsMSZCQu9HG8-SBpOZDNPeMdZGog6XA@mail.gmail.com/
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Cc: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: alsa-devel@alsa-project.org
CC: Kees Cook <keescook@chromium.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230213205223.2679357-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable ret is initialed but is never modified or used except for
returning the initial value 0. The value can be directly returned
instead and the variable definition can be dropped.
Issue identified using returnvar.cocci Coccinelle semantic patch.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/Y+p9r5y9DPSJkPVf@ubun2204.myguest.virtualbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5682s driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682s_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:
[ 19.672162] rt5682s 2-001a: ASoC: error at soc_component_read_no_lock on rt5682s.2-001a for register: [0x000000f0] -16
Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230209012002.1.Ib4d6481f1d38a6e7b8c9e04913c02ca88c216cf6@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable d0i3 streaming if all the active streams can
work in d0i3 state and playback is enabled.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Schedule a delayed work for d0i3 entry after every non-pm ipc msg.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver shall update the power state to D0i0 before sending
a generic IPC. Power-related IPCs are the exception to the rule,
they may be sent even when the power-state is D0i3
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use set_pm_gate to unify pm gate setting for different
ipc version.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set_pm_gate depends on ipc version. This patch defines
the ops for both IPC3 and IPC4.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's possible to exit the loop with "sysdev" set to NULL. In that
case we should use "&pdev->dev".
Fixes: ec5499d338 ("xhci: split out rcar/rz support from xhci-plat.c")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/Y+T4kTcJwRwxNHJq@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change on network namespace only makes sense during re-init reload
action. For FW activation it is not applicable. So check if user passed
an ATTR indicating network namespace change request and forbid it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230213115836.3404039-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Completion responses to SEND_RNDIS_PKT messages are currently processed
regardless of the status in the response, so that resources associated
with the request are freed. While this is appropriate, code bugs that
cause sending a malformed message, or errors on the Hyper-V host, go
undetected. Fix this by checking the status and outputting a rate-limited
message if there is an error.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1676264881-48928-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
MLD address translation should be done only for individually addressed
frames. Otherwise, AAD calculation would be wrong and the decryption
would fail.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Link: https://lore.kernel.org/r/20230214101048.792414-1-andrei.otcheretianski@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we now populate encoder->devdata for all DP capable
platforms we can consult it directly during the eDP
connector init instead of taking a detour via some global
list/array.
Unfortunately we can't quite get rid of
intel_dp_is_port_edp() since it's still used by the higher
level ilk/vlv/chv output setup code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Instead of consulting vbt.ports[] lets just go through the
whole child device list to check whether a specific port
was declared by the VBT or not.
Note that this doesn't change anything wrt. detecting duplicate
child devices with the same port as vbt.ports[] would also always
contain exactly one of the duplicates.
v2: Include a is_port_valid() check to deal with some broken VBTs
Mention something about duplicate port detection (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230214073818.20231-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently intel_bios_port_aux_ch() digs out the devdata
(VBT child device info) from the vbt.ports[] array. We
need to get rid of that, so just pass in the correct
encoder->devdata (now that we have it also for g4x+ ports)
directly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Let's make encoder->devdata (the VBT information for the port)
available on g4x+ platforms as well. Much easier when you can
just grab it there instead of trying to find it from some global
list array based on the port.
Note that (unlike DDI platforms) we don't currently require
that each DP/HDMI port is actually declared in VBT. Perhaps
in the future we may want to rethink that, but for now just
stick in a debug+FIXME as a reminder.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Display WA #1178 calls us to tweak some magic bits when doing AUX
to an external combo PHY port. Instead of looking to see if the VBT
has declared such a port (which could in theory even alias with a
declared eDP port on the same PHY) just check the real situation
based on the registered encoders.
The only slight chicken vs. egg situation here is during output
probing. But typically we'd register the eDP ports first and so
once we get to probe anything external on the combo PHY we have
already determined if it's eDP or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
intel_bios_is_port_hpd_inverted() is only used on bxt/glk on
which we always have encoder->devdata available. So consult
that instead of digging around in vbt.ports[].
And rename the function to match the common pattern.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The sole user of intel_bios_is_lane_reversal_needed() has
the devdata already located, so pass it in directly instead
of digging it again from vbt.ports[].
And rename the function to follow the common pattern for
these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We always have encoder->devdata available on the platforms
that can have LSPCON. So let's start looking there instead
of digging it out from vbt.ports[].
And let's rename the function to fit the common pattern
for these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
bxt_hotplug_enables() needs to dig out not only the
hpd_pin but also the VBT child device info, so let's just
pass in the whole encoder to avoid having to look things
up multiple times.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently the regulatory driver does not call the regulatory callback
reg_notifier for self managed wiphys. Sometimes driver needs cfg80211
to calculate the info of ieee80211_channel such as flags and power,
and driver needs to get the info of ieee80211_channel after hint of
driver, but driver does not know when calculation of the info of
ieee80211_channel become finished, so add notify to driver in
reg_process_self_managed_hint() from cfg80211 is a good way, then
driver could get the correct info in callback of reg_notifier.
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230201065313.27203-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wi-Fi Aware R4 specification defines NAN Pairing which uses PASN handshake
to authenticate the peer and generate keys. Hence allow to register and transmit
the PASN authentication frames on NAN interface and set the keys to driver or
underlying modules on NAN interface.
The driver needs to configure the feature flag NL80211_EXT_FEATURE_SECURE_NAN,
which also helps userspace modules to know if the driver supports secure NAN.
Signed-off-by: Vinay Gannevaram <quic_vganneva@quicinc.com>
Link: https://lore.kernel.org/r/1675519179-24174-1-git-send-email-quic_vganneva@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Non-MLO station frames are dropped in Rx path due to the condition
check in ieee80211_rx_is_valid_sta_link_id(). In multi-link AP scenario,
non-MLO stations try to connect in any of the valid links in the ML AP,
where the station valid_links and link_id params are valid in the
ieee80211_sta object. But ieee80211_rx_is_valid_sta_link_id() always
return false for the non-MLO stations by the assumption taken is
valid_links and link_id are not valid in non-MLO stations object
(ieee80211_sta), this assumption is wrong. Due to this assumption,
non-MLO station frames are dropped which leads to failure in association.
Fix it by removing the condition check and allow the link validation
check for the non-MLO stations.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://lore.kernel.org/r/20230206160330.1613-1-quic_periyasa@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stations can update bandwidth/NSS change in
VHT action frame with action type Operating Mode Notification.
(IEEE Std 802.11-2020 - 9.4.1.53 Operating Mode field)
For Operating Mode Notification, an RX NSS change to a value
greater than AP's maximum NSS should not be allowed.
During fuzz testing, by forcefully sending VHT Op. mode notif.
frames from STA with random rx_nss values, it is found that AP
accepts rx_nss values greater that APs maximum NSS instead of
discarding such NSS change.
Hence allow NSS change only up to maximum NSS that is negotiated
and capped to AP's capability during association.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/20230207114146.10567-1-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least ath10k and ath11k supported hardware (maybe more) does not implement
mesh A-MSDU aggregation in a standard compliant way.
802.11-2020 9.3.2.2.2 declares that the Mesh Control field is part of the
A-MSDU header (and little-endian).
As such, its length must not be included in the subframe length field.
Hardware affected by this bug treats the mesh control field as part of the
MSDU data and sets the length accordingly.
In order to avoid packet loss, keep track of which stations are affected
by this and take it into account when converting A-MSDU to 802.3 + mesh control
packets.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current mac80211 mesh A-MSDU receive path fails to parse A-MSDU packets
on mesh interfaces, because it assumes that the Mesh Control field is always
directly after the 802.11 header.
802.11-2020 9.3.2.2.2 Figure 9-70 shows that the Mesh Control field is
actually part of the A-MSDU subframe header.
This makes more sense, since it allows packets for multiple different
destinations to be included in the same A-MSDU, as long as RA and TID are
still the same.
Another issue is the fact that the A-MSDU subframe length field was apparently
accidentally defined as little-endian in the standard.
In order to fix this, the mesh forwarding path needs happen at a different
point in the receive path.
ieee80211_data_to_8023_exthdr is changed to ignore the mesh control field
and leave it in after the ethernet header. This also affects the source/dest
MAC address fields, which now in the case of mesh point to the mesh SA/DA.
ieee80211_amsdu_to_8023s is changed to deal with the endian difference and
to add the Mesh Control length to the subframe length, since it's not covered
by the MSDU length field.
With these changes, the mac80211 will get the same packet structure for
converted regular data packets and unpacked A-MSDU subframes.
The mesh forwarding checks are now only performed after the A-MSDU decap.
For locally received packets, the Mesh Control header is stripped away.
For forwarded packets, a new 802.11 header gets added.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-4-nbd@nbd.name
[fix fortify build error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that all drivers use iTXQ, it does not make sense to check to drop
tx forwarding packets when the driver has stopped the queues.
fq_codel will take care of dropping packets when the queues fill up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing the outer A-MSDU header, don't check for inner bridge tunnel
or RFC1042 headers. This is handled by ieee80211_amsdu_to_8023s already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The value of last_rate in ieee80211_sta_rx_stats is degraded from u32 to
u16 after being assigned to rate variable, which causes information loss
in STA_STATS_FIELD_TYPE and later bitfields.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://lore.kernel.org/r/20230209110659.25447-1-shayne.chen@mediatek.com
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230206081641.3193-1-liubo03@inspur.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently action frames TX only with ML address as A3(BSSID) are
allowed in an ML AP, but TX for a non-ML Station can happen in any
link of an ML BSS with link BSS address as A3.
In case of an MLD, if User-space has provided a valid link_id in
action frame TX request, allow transmission of the frame in that link.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/20230201061602.3918-1-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Configure the bitmap in link_conf and notify the driver.
- Modify 'change' in ieee80211_start_ap() from u32 to u64 to support
BSS_CHANGED_EHT_PUNCTURING.
- Propagate the bitmap in channel switch events to userspace.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-5-quic_alokad@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- New feature flag, NL80211_EXT_FEATURE_PUNCT, to advertise
driver support for preamble puncturing in AP mode.
- New attribute, NL80211_ATTR_PUNCT_BITMAP, to receive a puncturing
bitmap from the userspace during AP bring up (NL80211_CMD_START_AP)
and channel switch (NL80211_CMD_CHANNEL_SWITCH) operations. Each bit
corresponds to a 20 MHz channel in the operating bandwidth, lowest
bit for the lowest channel. Bit set to 1 indicates that the channel
is punctured. Higher 16 bits are reserved.
- New members added to structures cfg80211_ap_settings and
cfg80211_csa_settings to propagate the bitmap to the driver after
validation.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-3-quic_alokad@quicinc.com
[move validation against 0xffff into policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Move ieee80211_valid_disable_subchannel_bitmap() from mlme.c to
chan.c, rename it as cfg80211_valid_disable_subchannel_bitmap()
and export it.
- Modify the prototype to include struct cfg80211_chan_def instead
of only bandwidth to support a check which returns false if the
primary channel is punctured.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://lore.kernel.org/r/20230131001227.25014-2-quic_alokad@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
