Print the queue ID's during bind/unbind errors as well to make it easier
to see what failed exactly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230209142123.17193-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
resetting soundwire block will put the slaves out of sync and result
in re-enumeration during fsgen disable/enable path this is totally
unnecessary and resulting fifo overflows.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-8-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we ended up with incorrect mclk rate which should be
1920000 instead of 96000, So far we were getting lucky as the same clk
is set to 192000 by wsa and va macro. This issue is discovered when there
is no wsa macro active and only rx or tx path is tested.
Fix this by setting correct rate.
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: af3d54b997 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-7-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
currently q6apm_is_adsp_ready() will only return the cached value of
previous result. If we are unlucky and previous result is not-ready
then the caller will always get not-ready flag.
This is not correct, we should query the dsp of its current state in
irrespective of previous reported state.
Fixes: 47bc8cf60e ("ASoC: qdsp6: audioreach: Add ADSP ready check")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
At the moment, playing audio with PulseAudio with the qdsp6 driver
results in distorted sound. It seems like its timer-based scheduling
does not work properly with qdsp6 since setting tsched=0 in
the PulseAudio configuration avoids the issue.
Apparently this happens when the pointer() callback is not accurate
enough. There is a SNDRV_PCM_INFO_BATCH flag that can be used to stop
PulseAudio from using timer-based scheduling by default.
According to https://www.alsa-project.org/pipermail/alsa-devel/2014-March/073816.html:
The flag is being used in the sense explained in the previous audio
meeting -- the data transfer granularity isn't fine enough but aligned
to the period size (or less).
q6apm-dai reports the position as multiple of
prtd->pcm_count = snd_pcm_lib_period_bytes(substream)
so it indeed just a multiple of the period size.
Therefore adding the flag here seems appropriate and makes audio
work out of the box.
Comment log inspired by Stephan Gerhold sent for q6asm-dai.c few years back.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is noticed that the position pointer value seems to get a get corrupted
due to missing locking between updating and reading.
Fix this by adding a spinlock around the position pointer.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
prepare callback can be called multiple times, so unprepare the stream
if its already prepared.
Without this DSP is not happy to setting the params on a already
prepared graph.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As talked about in the patch ("dt-bindings: HID: i2c-hid: goodix: Add
mainboard-vddio-supply") we may need to power up a 1.8V rail on the
host associated with touchscreen IO. Let's add support in the driver
for it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230206184744.6.Ic234b931025d1f920ce9e06fff294643943a65ad@changeid
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The goodix i2c-hid bindings currently support two models of
touchscreen: GT7375P and GT7986U. The datasheets of both touchscreens
show the following things:
* The mainboard that the touchscreen is connected to is only expected
to supply one voltage to the touchscreen: 3.3V.
* The touchscreen, depending on stuffing options, can accept IO to the
touchscreen as either 3.3V or 1.8V. Presumably this means that the
touchscreen has its own way internally to make or deal with 1.8V
signals when it's configured for 1.8V IO.
NOTE: you've got to look very carefully at the datasheet for the
touchscreen to see that the above bullets are true. Specifically, the
datasheet shows a signal called VDDIO and one might think that this is
where a mainboard would provide VDDIO to the touchscreen. Upon closer
inspection, however, a footnote can be found that says "When VDDIO is
left floating, the logic level is 1.8V [...]; when VDDIO is connected
to AVDD, the logic level is AVDD.". Thus the VDDIO pin on the
touchscreen IC is actually a selector and not a pin whre the mainboard
would pass a reference voltage.
The fact that the touchscreen isn't supplied 1.8V by the mainboard
means that when I originally submitted bindings for these touchscreens
I only listed the 3.3V rail in the bindings. It can be noted that the
original bindings and driver were added for sc7180-trogdor boards and
these boards all use 3.3V IO via a level shifter on the mainboard.
It turns out that with sc7280-herobrine-evoker, we've got a bit of a
strange monkey on our hands. Due to some very interesting but
(unfortunately) set-in-stone hardware design, we are doing 1.8V IO to
the touchscreen but we _also_ have some extra buffers on the mainboard
that need to be powered up to make the IO lines work. After much
pondering about this, it seems like the best way to handle this is to
add an optional "mainboard-vddio" rail to the bindings that is used to
power up the buffers. Specifically, the fact that the touchscreen
datasheet documents that its IOs can be at a different voltage level
than its main power rail means that there truly are two voltage rails
associated with the touchscreen, even if we don't actually provide the
IO rail to it. Thus it doesn't feel absurd for the DT node on the host
to have a 1.8V rail to power up anything related to its 1.8V logic.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.5.Ia77a96c6c5564f9cc25e6220b5a9171d5c2639e8@changeid
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
In commit 18eeef46d3 ("HID: i2c-hid: goodix: Tie the reset line to
true state of the regulator"), we started tying the reset line of
Goodix touchscreens to the regulator.
The primary motivation for that patch was some pre-production hardware
(specifically sc7180-trogdor-homestar) where it was proposed to hook
the touchscreen's main 3.3V power rail to an always-on supply. In such
a case, when we turned "off" the touchscreen in Linux it was bad to
assert the "reset" GPIO because that was causing a power drain. The
patch accomplished that goal and did it in a general sort of way that
didn't require special properties to be added in the device tree for
homestar.
It turns out that the design of using an always-on power rail for the
touchscreen was rejected soon after the patch was written and long
before sc7180-trogdor-homestar went into production. The final design
of homestar actually fully separates the rail for the touchscreen and
the display panel and both can be powered off and on. That means that
the original motivation for the feature is gone.
There are 3 other users of the goodix i2c-hid driver in mainline.
I'll first talk about 2 of the other users in mainline: coachz and
mrbland. On both coachz and mrbland the touchscreen power and panel
power _are_ shared. That means that the patch to tie the reset line to
the true state of the regulator _is_ doing something on those
boards. Specifically, the patch reduced power consumption by tens of
mA in the case where we turned the touchscreen off but left the panel
on. Other than saving a small bit of power, the patch wasn't truly
necessary. That being said, even though a small bit of power was saved
in the state of "panel on + touchscreen off", that's not actually a
state we ever expect to be in, except perhaps for very short periods
of time at boot or during suspend/resume. Thus, the patch is truly not
necessary. It should be further noted that, as documented in the
original patch, the current code still didn't optimize power for every
corner case of the "shared rail" situation.
The last user in mainline was very recently added: evoker. Evoker is
actually the motivation for me removing this bit of code. It turns out
that for evoker we need to manage a second power rail for IO to the
touchscreen. Trying to fit the management of this IO rail into the
regulator notifiers turns out to be extremely hard. To avoid lockdep
splats you shouldn't enable/disable other regulators in regulator
notifiers and trying to find a way around this was going to be fairly
difficult.
Given the lack of any true motivation to tie the reset line to the
regulator, lets go back to the simpler days and remove the code. This
is, effectively, a revert of commit bdbc65eb77 ("HID: i2c-hid:
goodix: Fix a lockdep splat"), commit 25ddd7cfc5 ("HID: i2c-hid:
goodix: Use the devm variant of regulator_register_notifier()"), and
commit 18eeef46d3 ("HID: i2c-hid: goodix: Tie the reset line to true
state of the regulator").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20230206184744.4.I085b32b6140c7d1ac4e7e97b712bff9dd5962b62@changeid
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
The early_channel_count() function seems to have been useful in the past
for knowing how many EDAC mci structures to populate. However, this is no
longer needed as the maximum channel count for a system is used instead.
Remove the early_channel_count() helper functions and related code. Use the
size of the channel layer when iterating over channel structures.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230127170419.1824692-6-yazen.ghannam@amd.com
PCI Function 0 is used on Family 17h and later only to read the "dhar"
value. This value is printed and provided through a module-specific
debug sysfs file. The value is not used for any Family 17h and later
code, and it does not have any apparent debug value on these systems.
Remove "dhar", Function 0 PCI IDs, and all related code.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230127170419.1824692-5-yazen.ghannam@amd.com
In certain circumstances, such as when creating I2C-connected HID
devices, we want to pass and retain some quirks (axis inversion, etc).
The source of such quirks may be device tree, or DMI data, or something
else not readily available to the HID core itself and therefore cannot
be reconstructed easily. To allow this, introduce "initial_quirks" field
in hid_device structure and use it when determining the final set of
quirks.
This fixes the problem with i2c-hid setting up device-tree sourced
quirks too late and losing them on device rebind, and also allows to
sever the tie between hid-code and i2c-hid when applying DMI-based
quirks.
Fixes: b60d3c803d ("HID: i2c-hid-of: Expose the touchscreen-inverted properties")
Fixes: a2f416bf06 ("HID: multitouch: Add quirks for flipped axes")
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Allen Ballway <ballway@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/Y+LYwu3Zs13hdVDy@google.com
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
This patch adds an entry in the MAINTAINERS file for the MOST(R)
Technology driver.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Link: https://lore.kernel.org/r/20230209110651.168962-1-Parthiban.Veerasooran@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dummy cycles value was wrongly calculated if dummy.buswidth > 1,
which affects QSPI, OSPI, HyperFlash on various SoCs. We're lucky in
Single SPI case since its dummy.buswidth equals to 1, so the result of
the division is unchanged
This issue can be reproduced using something like the following commands
A. QSPI mode: Mount device with jffs2 format
jffs2: CLEANMARKER node found at 0x00000004, not first node in block (0x00000000)
B. QSPI mode: Write data to mtd10, where mtd10 is a parition on SPI Flash
storage, defined properly in a device tree
[Correct fragment, read from SPI Flash]
root@v3x:~# echo "hello" > /dev/mtd10
root@v3x:~# hexdump -C -n100 /dev/mtd10
00000000 68 65 6c 6c 6f 0a ff ff ff ff ff ff ff ff ff ff |hello...........|
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
[Incorrect read of the same fragment: see the difference at offsets 0-3]
root@v3x:~# echo "hello" > /dev/mtd10
root@v3x:~# hexdump -C -n100 /dev/mtd10
00000000 00 00 00 00 68 65 6c 6c 6f 0a ff ff ff ff ff ff |....hello.......|
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
As seen from the result, 4 NULL bytes were inserted before the test data.
Wrong calculation in rpcif_prepare() led to miss of some dummy cycle. A
division by bus width is redundant because it had been performed already
in spi-rpc-if.c::rpcif_spi_mem_prepare()
Fix this by removing the redundant division.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20230112090655.43367-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230207173051.449151-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It contains:
- cleanups arround flexcom nodes on SAM9X60 SoC as follows:
- preserve same ID for flexcoms and the embedded nodes (e.g. flx4
will embed uart4, spi4, i2c4 but not e.g. uart1, spi2, i2c3);
- SoC specific bindings were moved from board specific file to SoC
specific file
- DMA bindings for all flexcom nodes were added
- SoC file was filled with missing flexcom nodes
- new SAM9X60 Curiosity board that contains 1 uSDcard interface, 1 SDcard
interface, 1 USB device interface, 2 USB Type-A interfaces, 2 CAN
interfaces, 1 10/100 Ethernet interface, 1 LCD RGB666 interface,
1 Gb DDR2, 4 Gb NAND Flash, 2Kb EEPROM, leds, button, power
regulators, UART and JTAG connectors
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTsZ8eserC1pmhwqDmejrg/N2X7/QUCY+N5WwAKCRCejrg/N2X7
/QIbAQCQ5aARiG6B3IglSdVTQk8a+CRWpelxB9CMCXEohhRkhgD+JS6XRejjoF78
cj3J30OP1SnkZQtTOygxEtmaxEMHNw0=
=gcby
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Oe5O
-----END PGP SIGNATURE-----
Merge tag 'at91-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 device tree updates for 6.3 #2
It contains:
- cleanups arround flexcom nodes on SAM9X60 SoC as follows:
- preserve same ID for flexcoms and the embedded nodes (e.g. flx4
will embed uart4, spi4, i2c4 but not e.g. uart1, spi2, i2c3);
- SoC specific bindings were moved from board specific file to SoC
specific file
- DMA bindings for all flexcom nodes were added
- SoC file was filled with missing flexcom nodes
- new SAM9X60 Curiosity board that contains 1 uSDcard interface, 1 SDcard
interface, 1 USB device interface, 2 USB Type-A interfaces, 2 CAN
interfaces, 1 10/100 Ethernet interface, 1 LCD RGB666 interface,
1 Gb DDR2, 4 Gb NAND Flash, 2Kb EEPROM, leds, button, power
regulators, UART and JTAG connectors
* tag 'at91-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60 curiosity board
dt-bindings: arm: at91: Add info on sam9x60 curiosity
ARM: dts: at91: sam9x60: Add missing flexcom definitions
ARM: dts: at91: sam9x60: Add DMA bindings for the flexcom nodes
ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART
ARM: dts: at91: sam9x60: fix spi4 node
ARM: dts: at91: sam9x60: move flexcom definitions
ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions
Link: https://lore.kernel.org/r/20230209084930.289721-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A couple of tests roll their own auto-allocating file read logic.
Add a generic implementation and convert them to use it.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230203003947.38033-6-bgray@linux.ibm.com
Add helper functions to read and write (unsigned) long values directly
from/to files. One of the kernel interfaces uses hex strings, so we need
to allow passing a base too.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230203003947.38033-5-bgray@linux.ibm.com
Often a file is expected to hold an integral value. Existing functions
will use a C stdlib function like atoi or strtol to parse the file.
These operations are error prone, with complicated error conditions
(atoi returns 0 if not a number, and is undefined behaviour if not in
range. strtol returns 0 if not a number, and LONG_MIN/MAX if not in
range + sets errno to ERANGE).
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230203003947.38033-4-bgray@linux.ibm.com
Debugfs files are not always integers, so make *_file return/write a
byte buffer, and *_int deal with int values specifically. This increases
consistency with the other file read/write helpers.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230203003947.38033-3-bgray@linux.ibm.com
File read/write is reimplemented in about 5 different ways in the
various PowerPC selftests. This indicates it should be a common util.
Add a common read_file / write_file implementation and convert users
to it where (easily) possible.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230203003947.38033-2-bgray@linux.ibm.com
Use commonly used BIT() macro to define MSR_LINK_MASK. Equation is
not accepted by checkpatch because of missing spaces. Therefore line
needs to change anyhow.
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/20230208185645.GA14681@matrix-ESPRIMO-P710
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0c559bc8ab ("dt-bindings: serial: restrict possible child node
names") exposed the Allwinner D1 devicetrees as users of unevaluated
properties, with a slew of similar warnings now appearing during
dtbs_check:
sun20i-d1-nezha.dtb: serial@2500400: Unevaluated properties are not allowed ('dma-names', 'dmas' were unexpected)
Document the missing properties.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230208171715.70862-1-conor@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Alcor Link AK9563 smartcard reader used on some Lenovo platforms
doesn't work. If LPM is enabled the reader will provide an invalid
usb config descriptor. Added quirk to disable LPM.
Verified fix on Lenovo P16 G1 and T14 G3
Tested-by: Miroslav Zatko <mzatko@mirexoft.com>
Tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20230208181223.1092654-1-mpearson-lenovo@squebb.ca
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While checking Pin Assignments of the port and partner during probe, we
don't take into account whether the peripheral is a plug or receptacle.
This manifests itself in a mode entry failure on certain docks and
dongles with captive cables. For instance, the Startech.com Type-C to DP
dongle (Model #CDP2DP) advertises its DP VDO as 0x405. This would fail
the Pin Assignment compatibility check, despite it supporting
Pin Assignment C as a UFP.
Update the check to use the correct DP Pin Assign macros that
take the peripheral's receptacle bit into account.
Fixes: c1e5c2f0cb ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Reported-by: Diana Zigterman <dzigterman@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20230208205318.131385-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 321b59870f.
This commit broke USB networking on Ingenic SoCs and maybe elsewhere.
The actual reason is unknown; and while a proper fix would be better,
we're sitting at -rc7 now, so a revert is justified - and we can work on
re-introducing this change for 6.3.
Fixes: 321b59870f ("usb: gadget: u_ether: Do not make UDC parent of the net device")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230209105626.10597-1-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The max98090 has only one DAI and does not take argument to DAI
phandles:
exynos5250-snow-rev5.dtb: audio-codec@10: #sound-dai-cells:0:0: 0 was expected
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20230208160424.371678-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Commit 550b33cfd4 ("arm64: efi: Force the use of SetVirtualAddressMap()
on Altra machines") identifies the Altra family via the family field in
the type#1 SMBIOS record. eMAG and Altra Max machines are similarly
affected but not detected with the strict strcmp test.
The type1_family smbios string is not an entirely reliable means of
identifying systems with this issue as OEMs can, and do, use their own
strings for these fields. However, until we have a better solution,
capture the bulk of these systems by adding strcmp matching for "eMAG"
and "Altra Max".
Fixes: 550b33cfd4 ("arm64: efi: Force the use of SetVirtualAddressMap() on Altra machines")
Cc: <stable@vger.kernel.org> # 6.1.x
Cc: Alexandru Elisei <alexandru.elisei@gmail.com>
Signed-off-by: Darren Hart <darren@os.amperecomputing.com>
Tested-by: Justin He <justin.he@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
