Fix UBSAN warnings that occur when using a system with 32 physical
cpu cores or more, or when the user defines a number of Ethernet
queues greater than or equal to FP_SB_MAX_E1x using the num_queues
module parameter.
Currently there is a read/write out of bounds that occurs on the array
"struct stats_query_entry query" present inside the "bnx2x_fw_stats_req"
struct in "drivers/net/ethernet/broadcom/bnx2x/bnx2x.h".
Looking at the definition of the "struct stats_query_entry query" array:
struct stats_query_entry query[FP_SB_MAX_E1x+
BNX2X_FIRST_QUEUE_QUERY_IDX];
FP_SB_MAX_E1x is defined as the maximum number of fast path interrupts and
has a value of 16, while BNX2X_FIRST_QUEUE_QUERY_IDX has a value of 3
meaning the array has a total size of 19.
Since accesses to "struct stats_query_entry query" are offset-ted by
BNX2X_FIRST_QUEUE_QUERY_IDX, that means that the total number of Ethernet
queues should not exceed FP_SB_MAX_E1x (16). However one of these queues
is reserved for FCOE and thus the number of Ethernet queues should be set
to [FP_SB_MAX_E1x -1] (15) if FCOE is enabled or [FP_SB_MAX_E1x] (16) if
it is not.
This is also described in a comment in the source code in
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h just above the Macro definition
of FP_SB_MAX_E1x. Below is the part of this explanation that it important
for this patch
/*
* The total number of L2 queues, MSIX vectors and HW contexts (CIDs) is
* control by the number of fast-path status blocks supported by the
* device (HW/FW). Each fast-path status block (FP-SB) aka non-default
* status block represents an independent interrupts context that can
* serve a regular L2 networking queue. However special L2 queues such
* as the FCoE queue do not require a FP-SB and other components like
* the CNIC may consume FP-SB reducing the number of possible L2 queues
*
* If the maximum number of FP-SB available is X then:
* a. If CNIC is supported it consumes 1 FP-SB thus the max number of
* regular L2 queues is Y=X-1
* b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor)
* c. If the FCoE L2 queue is supported the actual number of L2 queues
* is Y+1
* d. The number of irqs (MSIX vectors) is either Y+1 (one extra for
* slow-path interrupts) or Y+2 if CNIC is supported (one additional
* FP interrupt context for the CNIC).
* e. The number of HW context (CID count) is always X or X+1 if FCoE
* L2 queue is supported. The cid for the FCoE L2 queue is always X.
*/
However this driver also supports NICs that use the E2 controller which can
handle more queues due to having more FP-SB represented by FP_SB_MAX_E2.
Looking at the commits when the E2 support was added, it was originally
using the E1x parameters: commit f2e0899f0f ("bnx2x: Add 57712 support").
Back then FP_SB_MAX_E2 was set to 16 the same as E1x. However the driver
was later updated to take full advantage of the E2 instead of having it be
limited to the capabilities of the E1x. But as far as we can tell, the
array "stats_query_entry query" was still limited to using the FP-SB
available to the E1x cards as part of an oversignt when the driver was
updated to take full advantage of the E2, and now with the driver being
aware of the greater queue size supported by E2 NICs, it causes the UBSAN
warnings seen in the stack traces below.
This patch increases the size of the "stats_query_entry query" array by
replacing FP_SB_MAX_E1x with FP_SB_MAX_E2 to be large enough to handle
both types of NICs.
Stack traces:
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1529:11
index 20 is out of range for type 'stats_query_entry [19]'
CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_prep_fw_stats_req+0x2e1/0x310 [bnx2x]
bnx2x_stats_init+0x156/0x320 [bnx2x]
bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x]
bnx2x_nic_load+0x8e8/0x19e0 [bnx2x]
bnx2x_open+0x16b/0x290 [bnx2x]
__dev_open+0x10e/0x1d0
RIP: 0033:0x736223927a0a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca
64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a
RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003
RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080
R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0
R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00
</TASK>
---[ end trace ]---
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1546:11
index 28 is out of range for type 'stats_query_entry [19]'
CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_prep_fw_stats_req+0x2fd/0x310 [bnx2x]
bnx2x_stats_init+0x156/0x320 [bnx2x]
bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x]
bnx2x_nic_load+0x8e8/0x19e0 [bnx2x]
bnx2x_open+0x16b/0x290 [bnx2x]
__dev_open+0x10e/0x1d0
RIP: 0033:0x736223927a0a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca
64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a
RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003
RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080
R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0
R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00
</TASK>
---[ end trace ]---
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1895:8
index 29 is out of range for type 'stats_query_entry [19]'
CPU: 13 PID: 163 Comm: kworker/u96:1 Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Workqueue: bnx2x bnx2x_sp_task [bnx2x]
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_iov_adjust_stats_req+0x3c4/0x3d0 [bnx2x]
bnx2x_storm_stats_post.part.0+0x4a/0x330 [bnx2x]
? bnx2x_hw_stats_post+0x231/0x250 [bnx2x]
bnx2x_stats_start+0x44/0x70 [bnx2x]
bnx2x_stats_handle+0x149/0x350 [bnx2x]
bnx2x_attn_int_asserted+0x998/0x9b0 [bnx2x]
bnx2x_sp_task+0x491/0x5c0 [bnx2x]
process_one_work+0x18d/0x3f0
</TASK>
---[ end trace ]---
Fixes: 50f0a562f8 ("bnx2x: add fcoe statistics")
Signed-off-by: Ghadi Elie Rahme <ghadi.rahme@canonical.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20240627111405.1037812-1-ghadi.rahme@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the existing test to exercise UDP GSO egress through devices with
various offload capabilities, including lack of checksum offload, which is
the default case for TUN/TAP devices.
Test against a dummy device because it is simpler to set up then TUN/TAP.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240626-linux-udpgso-v2-2-422dfcbd6b48@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Today sending a UDP GSO packet from a TUN device results in an EIO error:
import fcntl, os, struct
from socket import *
TUNSETIFF = 0x400454CA
IFF_TUN = 0x0001
IFF_NO_PI = 0x1000
UDP_SEGMENT = 103
tun_fd = os.open("/dev/net/tun", os.O_RDWR)
ifr = struct.pack("16sH", b"tun0", IFF_TUN | IFF_NO_PI)
fcntl.ioctl(tun_fd, TUNSETIFF, ifr)
os.system("ip addr add 192.0.2.1/24 dev tun0")
os.system("ip link set dev tun0 up")
s = socket(AF_INET, SOCK_DGRAM)
s.setsockopt(SOL_UDP, UDP_SEGMENT, 1200)
s.sendto(b"x" * 3000, ("192.0.2.2", 9)) # EIO
This is due to a check in the udp stack if the egress device offers
checksum offload. While TUN/TAP devices, by default, don't advertise this
capability because it requires support from the TUN/TAP reader.
However, the GSO stack has a software fallback for checksum calculation,
which we can use. This way we don't force UDP_SEGMENT users to handle the
EIO error and implement a segmentation fallback.
Lift the restriction so that UDP_SEGMENT can be used with any egress
device. We also need to adjust the UDP GSO code to match the GSO stack
expectation about ip_summed field, as set in commit 8d63bee643 ("net:
avoid skb_warn_bad_offload false positives on UFO"). Otherwise we will hit
the bad offload check.
Users should, however, expect a potential performance impact when
batch-sending packets with UDP_SEGMENT without checksum offload on the
egress device. In such case the packet payload is read twice: first during
the sendmsg syscall when copying data from user memory, and then in the GSO
stack for checksum computation. This double memory read can be less
efficient than a regular sendmsg where the checksum is calculated during
the initial data copy from user memory.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240626-linux-udpgso-v2-1-422dfcbd6b48@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCH_READ_NODECODE mode - used by the move paths - really wants to use
only the original rbio, but the retry path really wants to clone - oof.
Make sure to copy the crc of the pointer we read from back to the
original rbio, or we'll see spurious checksum errors later.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
On a new filesystem or device we have to allocate the journal with a
bump allocator, because allocation info isn't ready yet - but when
hot-adding a device that doesn't have a journal, we don't want to use
that path.
Reported-by: syzbot+24a867cb90d8315cccff@syzkaller.appspotmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
* A fix for vector load/store instruction decoding, which could result
in reserved vector element length encodings decoding as valid vector
instructions.
* Instruction patching now aggressively flushes the local instruction
cache, to avoid situations where patching functions on the flush path
results in torn instructions being fetched.
* A fix to prevent the stack walker from showing up as part of traces.
-----BEGIN PGP SIGNATURE-----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=0bpZ
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix for vector load/store instruction decoding, which could result
in reserved vector element length encodings decoding as valid vector
instructions.
- Instruction patching now aggressively flushes the local instruction
cache, to avoid situations where patching functions on the flush path
results in torn instructions being fetched.
- A fix to prevent the stack walker from showing up as part of traces.
* tag 'riscv-for-linus-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: stacktrace: convert arch_stack_walk() to noinstr
riscv: patch: Flush the icache right after patching to avoid illegal insns
RISC-V: fix vector insn load/store width mask
Test if KVM emulates the APIC bus clock at the expected frequency when
userspace configures the frequency via KVM_CAP_X86_APIC_BUS_CYCLES_NS.
Set APIC timer's initial count to the maximum value and busy wait for 100
msec (largely arbitrary) using the TSC. Read the APIC timer's "current
count" to calculate the actual APIC bus clock frequency based on TSC
frequency.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Co-developed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lore.kernel.org/r/2fccf35715b5ba8aec5e5708d86ad7015b8d74e6.1718214999.git.reinette.chatre@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Allocating a contiguous buffer of 64K may fail if memory is sufficiently
fragmented, and may cause OOM kill of an unrelated process. However we
do not need to have contiguous memory. We also do not need to zero
out the buffer since it will be overwritten with firmware data.
Switch to using kvmalloc() instead of kzalloc().
Link: https://lore.kernel.org/r/20240609234757.610273-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch the driver to use guard notation when acquiring mutex to
have it released automatically.
Link: https://lore.kernel.org/r/Zmkyvkr9AFyywy1V@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In arch/arm64/include/uapi/asm/kvm.h, we have
#define KVM_VGIC_V2_CPU_SIZE 0x2000
So the CPU interface address space should cover 8 KByte not 4 KByte.
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Link: https://lore.kernel.org/r/20240623164542.2999626-3-changyuanl@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
The expression `irq_type[n]` may confuse readers to interpret `n`
as the bit position and think of CPU = 1 << 0, SPI = 1 << 1, and
PPI = 1 << 2.
Since arch/arm64/include/uapi/asm/kvm.h already has macro definitions
for the allowed values, this commit uses these symbols to clear up
the ambiguity.
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Link: https://lore.kernel.org/r/20240623164542.2999626-2-changyuanl@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Execution of the 'make' command in the 'bench' subfolder causes the
following error:
$ make O=cpupower/build/ DESTDIR=cpupower/install/ -j8
" CC " cpupower/build//main.o
" CC " cpupower/build//parse.o
/bin/sh: 1: " CC "cpupower/build//system.o
CC : not found
make: *** [Makefile:21: cpupower/build//main.o] Error 127
make: *** Waiting for unfinished jobs....
/bin/sh: 1: CC : not found
/bin/sh: 1: CC : not found
make: *** [Makefile:21: cpupower/build//parse.o] Error 127
make: *** [Makefile:21: cpupower/build//system.o] Error 127
The makefile uses variables defined in the main project makefile and it
is not intended to run standalone. The reason is that 'bench' subproject
depends on the 'libcpupower' library, see the 'compile-bench' target in
the main makefile.
Add a check that prevents standalone execution of the 'bench' makefile.
Signed-off-by: Roman Storozhenko <romeusmeister@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Marc Kleine-Budde <mkl@pengutronix.de> says:
This patch series tries to work around erratum DS80000789E 6 of the
mcp2518fd, found by Stefan Althöfer, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value.
For the RX FIDO this caused old, already processed CAN frames or new,
incompletely written CAN frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp of the last valid
received CAN frame and compare against the timestamp of every received
CAN frame.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames are not recognized but then processed. These CAN frames have
the correct data and time stamps, but the DLC has not yet been
updated.
For the TEF FIFO the original driver already detects the error, update
the error handling with the knowledge that it is causes by this erratum.
Link: https://lore.kernel.org/all/20240628-mcp251xfd-workaround-erratum-6-v4-0-53586f168524@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch updates the workaround for a problem similar to erratum
DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. As the FIFO
is implemented as a ring buffer, this results in re-handling old CAN
transmit complete events.
Every transmit complete event contains with a sequence number that
equals to the sequence number of the corresponding TX request. This
way old TX complete events can be detected.
If the original driver detects a non matching sequence number, it
prints an info message and tries again later. As wrong sequence
numbers can be explained by the erratum DS80000789E 6, demote the info
message to debug level, streamline the code and update the comments.
Keep the behavior: If an old CAN TX complete event is detected, abort
the iteration and mark the number of valid CAN TX complete events as
processed in the chip by incrementing the FIFO's tail index.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparatory patch to work around a problem similar to
erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
When handling the TEF interrupt, the driver reads the FIFO header
index from the TEF FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN transmit complete events that were already processed to be
re-processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_tef_ring_update() with mcp251xfd_get_tef_len().
The mcp251xfd_handle_tefif() function reads the CAN transmit complete
events from the chip, iterates over them and pushes them into the
network stack. The original driver already contains code to detect old
CAN transmit complete events, that will be updated in the next patch.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch tries to works around erratum DS80000789E 6 of the
mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old, already processed CAN frames or new, incompletely written CAN
frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp [1] of the last
valid received CAN frame and compare against the timestamp of every
received CAN frame. If an old CAN frame is detected, abort the
iteration and mark the number of valid CAN frames as processed in the
chip by incrementing the FIFO's tail index.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames [2] are not recognized but then processed. These CAN frames
have the correct data and time stamps, but the DLC has not yet been
updated.
[1] As the raw timestamp overflows every 107 seconds (at the usual
clock rate of 40 MHz) convert it to nanoseconds with the
timecounter framework and use this to detect stale CAN frames.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com [2]
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparatory patch to work around erratum DS80000789E 6 of
the mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
When handling the RX interrupt, the driver iterates over all pending
FIFOs (which are implemented as ring buffers in hardware) and reads
the FIFO header index from the RX FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN frames that were already processed, or new, incompletely
written CAN frames to be (re-)processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_rx_ring_update() with mcp251xfd_get_rx_len().
The mcp251xfd_handle_rxif_ring() function reads the received CAN
frames from the chip, iterates over them and pushes them into the
network stack. Prepare that the iteration can be stopped if an old CAN
frame is detected. The actual code to detect old or incomplete frames
and abort will be added in the next patch.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch.
Sending the UINC messages followed by incrementing the tail pointer
will be called in more than one place in upcoming patches, so factor
this out into a separate function.
Also make mcp251xfd_handle_rxif_ring_uinc() safe to be called with a
"len" of 0.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd chip is configured to provide a timestamp with each
received and transmitted CAN frame. The timestamp is derived from the
internal free-running timer, which can also be read from the TBC
register via SPI. The timer is 32 bits wide and is clocked by the
external oscillator (typically 20 or 40 MHz).
To avoid confusion, we call this timestamp "timestamp_raw" or "ts_raw"
for short.
Using the timecounter framework, the "ts_raw" is converted to 64 bit
nanoseconds since the epoch. This is what we call "timestamp".
This is a preparation for the next patches which use the "timestamp"
to work around a bug where so far only the "ts_raw" is used.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd wakes up from Low Power or Sleep Mode when SPI activity
is detected. To avoid this, make sure that the timestamp worker is
stopped before shutting down the chip.
Split the starting of the timestamp worker out of
mcp251xfd_timestamp_init() into the separate function
mcp251xfd_timestamp_start().
Call mcp251xfd_timestamp_init() before mcp251xfd_chip_start(), move
mcp251xfd_timestamp_start() to mcp251xfd_chip_start(). In this way,
mcp251xfd_timestamp_stop() can be called unconditionally by
mcp251xfd_chip_stop().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since the errata references have been added to the driver, new errata
sheets have been published. Update the references for the mcp2517fd
and mcp2518fd. For completeness add references for the mcp251863.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The 'profile_pc()' function is used for timer-based profiling, which
isn't really all that relevant any more to begin with, but it also ends
up making assumptions based on the stack layout that aren't necessarily
valid.
Basically, the code tries to account the time spent in spinlocks to the
caller rather than the spinlock, and while I support that as a concept,
it's not worth the code complexity or the KASAN warnings when no serious
profiling is done using timers anyway these days.
And the code really does depend on stack layout that is only true in the
simplest of cases. We've lost the comment at some point (I think when
the 32-bit and 64-bit code was unified), but it used to say:
Assume the lock function has either no stack frame or a copy
of eflags from PUSHF.
which explains why it just blindly loads a word or two straight off the
stack pointer and then takes a minimal look at the values to just check
if they might be eflags or the return pc:
Eflags always has bits 22 and up cleared unlike kernel addresses
but that basic stack layout assumption assumes that there isn't any lock
debugging etc going on that would complicate the code and cause a stack
frame.
It causes KASAN unhappiness reported for years by syzkaller [1] and
others [2].
With no real practical reason for this any more, just remove the code.
Just for historical interest, here's some background commits relating to
this code from 2006:
0cb91a2293 ("i386: Account spinlocks to the caller during profiling for !FP kernels")
31679f38d8 ("Simplify profile_pc on x86-64")
and a code unification from 2009:
ef4512882d ("x86: time_32/64.c unify profile_pc")
but the basics of this thing actually goes back to before the git tree.
Link: https://syzkaller.appspot.com/bug?extid=84fe685c02cd112a2ac3 [1]
Link: https://lore.kernel.org/all/CAK55_s7Xyq=nh97=K=G1sxueOFrJDAvPOJAL4TPTCAYvmxO9_A@mail.gmail.com/ [2]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
A couple copy/paste mistakes in the code that selects steering targets
for OADDRM and INSTANCE0 unintentionally clobbered the steering target
for DSS ranges in some cases.
The OADDRM/INSTANCE0 values were also not assigned as intended, although
that mistake wound up being harmless since the desired values for those
specific ranges were '0' which the kzalloc of the GT structure should
have already taken care of implicitly.
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626210536.1620176-2-matthew.d.roper@intel.com
The kobject for the queue entries is embedded into a struct gendisk.
Pass it to the sysfs methods instead of the request_queue derived from
it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240627111407.476276-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A lof the code to implement the queue sysfs attributes is repetitive.
Add a few macros to generate the common cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240627111407.476276-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
queue_logical_block_size is never called with a 0 queue, and the
logical_block_size field in queue_limits is always initialized for
a live queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240627111407.476276-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It's not very obvious what the difference is between the 'size' and
'n_entries' fields of the MOCS structure. Rename both fields slightly
and add some comments explaining that one is the documentation-defined
table size, while the other is the number of entries that can be
programmed into the hardware (and the documented table size can
potentially be smaller than the number of hardware entries).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627203741.2042752-4-matthew.d.roper@intel.com
Rely more heavily on assertions to describe the MOCS programming
invariants. CI checks these assertions and will ensure no violations
sneak in due to programmer error, so we can remove some of the redundant
WARN and silent return checks from non-debug builds.
Also tweak/augment some of the existing assertions: there's no reason
we'd ever want a platform not to have a MOCS 'ops' structure hooked up
so ensure info->ops is non-NULL. Likewise, we should never have a case
where the bspec-defined MOCS setting table is larger than the number of
MOCS registers exposed by the hardware, so add an extra assert on those
sizes as well.
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627203741.2042752-3-matthew.d.roper@intel.com
User will configure allowed iops limit in 1s, and calculate_io_allowed()
will calculate allowed iops in the slice by:
limit * HZ / throtl_slice
However, if limit is quite low, the result can be 0, then
allowed IO in the slice is 0, this will cause missing dispatch and
control will be lower than limit.
For example, set iops_limit to 5 with HD disk, and test will found that
iops will be 3.
This is usually not a big deal, because user will unlikely to configure
such low iops limit, however, this is still a problem in the extreme
scene.
Fix the problem by making sure the wait time calculated by
tg_within_iops_limit() should allow at least one IO to be dispatched.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20240618062108.3680835-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set the bip_vcnt correctly in bio_integrity_init_user and
bio_integrity_copy_user. If the bio gets split at a later point,
this value is required to set the right bip_vcnt in the cloned bio.
Signed-off-by: Anuj Gupta <anuj20.g@samsung.com>
Signed-off-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240626100700.3629-3-anuj20.g@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Block device features and flags were refactored from `enum` to `#define`.
This broke Rust binding generation. This patch fixes the binding
generation.
Fixes: fcf865e357 ("block: convert features and flags to __bitwise types")
Signed-off-by: Andreas Hindborg <a.hindborg@samsung.com>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Link: https://lore.kernel.org/r/20240628091152.2185241-1-nmi@metaspace.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Allocate and initialize struct ice_adapter object only once per physical
card instead of once per port. This is not a big deal by now, but we want
to extend this struct more and more in the near future. Our plans include
PTP stuff and a devlink instance representing whole-device/physical card.
Transactions requiring to be sleep-able (like those doing user (here ice)
memory allocation) must be performed with an additional (on top of xarray)
mutex. Adding it here removes need to xa_lock() manually.
Since this commit is a reimplementation of ice_adapter_get(), a rather new
scoped_guard() wrapper for locking is used to simplify the logic.
It's worth to mention that xa_insert() use gives us both slot reservation
and checks if it is already filled, what simplifies code a tiny bit.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the -r/--repeat option accepts values from 0 and complains
for -1. The help section specifies:
-r, --repeat <n> repeat the workload replay N times (-1: infinite)
The -r -1 option raises an error because replay_repeat is defined as
an unsigned int.
In the current implementation, the workload is repeated n times when
-r <n> is used, except when n is 0.
When -r is set to 0, the workload is also repeated once. This happens
because when -r=0, the run_one_test function is not called. (Note that
mutex unlocking, which is essential for child threads spawned to emulate
the workload, happens in run_one_test.) However, mutex unlocking is
still performed in the destroy_tasks function. Thus, -r=0 results in the
workload running once coincidentally.
To clarify and maintain the existing logic for -r >= 1 (which runs the
workload the specified number of times) and to fix the issue with infinite
runs, make -r=0 perform an infinite run.
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: Madadi Vineeth Reddy <vineethr@linux.ibm.com>
Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20240628071821.15264-1-vineethr@linux.ibm.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Add labels from IIO channels to our channels. This allows userspace to
display more meaningful names instead of "in0" or "temp5".
Although lm-sensors gracefully handles errors when reading channel
labels, the ABI says the label attribute
> Should only be created if the driver has hints about what this voltage
> channel is being used for, and user-space doesn't.
Therefore, we test to see if the channel has a label before
creating the attribute.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20240624174601.1527244-3-sean.anderson@linux.dev
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It can be convenient for other in-kernel drivers to reuse IIO channel
labels. Export the iio_read_channel_label function to allow this. The
signature is different depending on where we are calling it from, so
the meat is moved to do_iio_read_channel_label.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://patch.msgid.link/20240624174601.1527244-2-sean.anderson@linux.dev
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
