SoC TRM, SoC datasheet and board schematics always refer to the
same i2c numbers - even if not all are used for a specific board.
In order to not have to re-define them for every board move the
aliases to SoC dtsi for RK3128 like it's being done for all other
Rockchip ARM SoCs.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231202130506.66738-4-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
SoC TRM, SoC datasheet and board schematics always refer to the
same gpio numbers - even if not all are used for a specific board.
In order to not have to re-define them for every board move the
aliases to SoC dtsi for RK3128 like it's being done for most other
Rockchip ARM SoCs.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231202130506.66738-3-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
This patch adds the initial device tree for this device, it is largely
based off the device trees for mainline Edgeble Neu2 and downstream
Rockchip rv1126-evb-v13 configs. It has been adapted with relevant
peripheral and GPIO pins for the iHost.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://lore.kernel.org/r/20231203124004.2676174-8-tim@feathertop.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Sonoff iHost is a smart home hub with built in radios for wifi/bt
and Zigbee. It is based off the Rockchip RV1126 (or RV1109) SoC.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231203124004.2676174-9-tim@feathertop.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Rockchip rv1109 SoC is a dual core version of the rv1126. It is
otherwise identical and shares the same device tree config.
This patch introduces a dtsi file to drop the additional cpu nodes.
Taken from Rockchip BSP kernel.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://lore.kernel.org/r/20231203124004.2676174-7-tim@feathertop.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add uart3m2_xfer and uart4m2_xfer pins for Rockchip RV1126. These are
used as serial ports for the indicator and Zigbee radio on the iHost.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://lore.kernel.org/r/20231203124004.2676174-2-tim@feathertop.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3128 SoCs have Mali400 MP2 GPU.
Add the respective device tree node and the correspondending opp-table.
The frequencies and voltages of the opp-table have been taken from
downstream kernel.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231204153547.97877-3-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Cc: stable@vger.kernel.org
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Previously, when comparing the net namespaces, the case where the netdev
doesn't exist wasn't taken into account, and therefore can cause a crash.
In such a case, the comparing function should return false, as there is no
netdev->net to compare the devlink->net to.
Furthermore, this will result in an attempt to enter switchdev mode
without a netdev to fail, and which is the desired result as there is no
meaning in switchdev mode without a net device.
Fixes: 662404b24a ("net/mlx5e: Block entering switchdev mode with ns inconsistency")
Signed-off-by: Gavin Li <gavinl@nvidia.com>
Reviewed-by: Gavi Teitz <gavi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Current sync reset flow is not supported when PCIe bridge connected
directly to mlx5 device has HotPlug interrupt enabled and can be
triggered on link state change event. Return nack on reset request in
such case.
Fixes: 92501fa6e4 ("net/mlx5: Ack on sync_reset_request only if PF can do reset_now")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Due to the cited patch, devlink health commands take devlink lock and
this may result in deadlock for mlx5e_tx_reporter as it takes local
state_lock before calling devlink health report and on the other hand
devlink health commands such as diagnose for same reporter take local
state_lock after taking devlink lock (see kernel log below).
To fix it, remove local state_lock from mlx5e_tx_timeout_work() before
calling devlink_health_report() and take care to cancel the work before
any call to close channels, which may free the SQs that should be
handled by the work. Before cancel_work_sync(), use current_work() to
check we are not calling it from within the work, as
mlx5e_tx_timeout_work() itself may close the channels and reopen as part
of recovery flow.
While removing state_lock from mlx5e_tx_timeout_work() keep rtnl_lock to
ensure no change in netdev->real_num_tx_queues, but use rtnl_trylock()
and a flag to avoid deadlock by calling cancel_work_sync() before
closing the channels while holding rtnl_lock too.
Kernel log:
======================================================
WARNING: possible circular locking dependency detected
6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1 Not tainted
------------------------------------------------------
kworker/u16:2/65 is trying to acquire lock:
ffff888122f6c2f8 (&devlink->lock_key#2){+.+.}-{3:3}, at: devlink_health_report+0x2f1/0x7e0
but task is already holding lock:
ffff888121d20be0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_tx_timeout_work+0x70/0x280 [mlx5_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&priv->state_lock){+.+.}-{3:3}:
__mutex_lock+0x12c/0x14b0
mlx5e_rx_reporter_diagnose+0x71/0x700 [mlx5_core]
devlink_nl_cmd_health_reporter_diagnose_doit+0x212/0xa50
genl_family_rcv_msg_doit+0x1e9/0x2f0
genl_rcv_msg+0x2e9/0x530
netlink_rcv_skb+0x11d/0x340
genl_rcv+0x24/0x40
netlink_unicast+0x438/0x710
netlink_sendmsg+0x788/0xc40
sock_sendmsg+0xb0/0xe0
__sys_sendto+0x1c1/0x290
__x64_sys_sendto+0xdd/0x1b0
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
-> #0 (&devlink->lock_key#2){+.+.}-{3:3}:
__lock_acquire+0x2c8a/0x6200
lock_acquire+0x1c1/0x550
__mutex_lock+0x12c/0x14b0
devlink_health_report+0x2f1/0x7e0
mlx5e_health_report+0xc9/0xd7 [mlx5_core]
mlx5e_reporter_tx_timeout+0x2ab/0x3d0 [mlx5_core]
mlx5e_tx_timeout_work+0x1c1/0x280 [mlx5_core]
process_one_work+0x7c2/0x1340
worker_thread+0x59d/0xec0
kthread+0x28f/0x330
ret_from_fork+0x1f/0x30
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&priv->state_lock);
lock(&devlink->lock_key#2);
lock(&priv->state_lock);
lock(&devlink->lock_key#2);
*** DEADLOCK ***
4 locks held by kworker/u16:2/65:
#0: ffff88811a55b138 ((wq_completion)mlx5e#2){+.+.}-{0:0}, at: process_one_work+0x6e2/0x1340
#1: ffff888101de7db8 ((work_completion)(&priv->tx_timeout_work)){+.+.}-{0:0}, at: process_one_work+0x70f/0x1340
#2: ffffffff84ce8328 (rtnl_mutex){+.+.}-{3:3}, at: mlx5e_tx_timeout_work+0x53/0x280 [mlx5_core]
#3: ffff888121d20be0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_tx_timeout_work+0x70/0x280 [mlx5_core]
stack backtrace:
CPU: 1 PID: 65 Comm: kworker/u16:2 Not tainted 6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5e mlx5e_tx_timeout_work [mlx5_core]
Call Trace:
<TASK>
dump_stack_lvl+0x57/0x7d
check_noncircular+0x278/0x300
? print_circular_bug+0x460/0x460
? find_held_lock+0x2d/0x110
? __stack_depot_save+0x24c/0x520
? alloc_chain_hlocks+0x228/0x700
__lock_acquire+0x2c8a/0x6200
? register_lock_class+0x1860/0x1860
? kasan_save_stack+0x1e/0x40
? kasan_set_free_info+0x20/0x30
? ____kasan_slab_free+0x11d/0x1b0
? kfree+0x1ba/0x520
? devlink_health_do_dump.part.0+0x171/0x3a0
? devlink_health_report+0x3d5/0x7e0
lock_acquire+0x1c1/0x550
? devlink_health_report+0x2f1/0x7e0
? lockdep_hardirqs_on_prepare+0x400/0x400
? find_held_lock+0x2d/0x110
__mutex_lock+0x12c/0x14b0
? devlink_health_report+0x2f1/0x7e0
? devlink_health_report+0x2f1/0x7e0
? mutex_lock_io_nested+0x1320/0x1320
? trace_hardirqs_on+0x2d/0x100
? bit_wait_io_timeout+0x170/0x170
? devlink_health_do_dump.part.0+0x171/0x3a0
? kfree+0x1ba/0x520
? devlink_health_do_dump.part.0+0x171/0x3a0
devlink_health_report+0x2f1/0x7e0
mlx5e_health_report+0xc9/0xd7 [mlx5_core]
mlx5e_reporter_tx_timeout+0x2ab/0x3d0 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x400/0x400
? mlx5e_reporter_tx_err_cqe+0x1b0/0x1b0 [mlx5_core]
? mlx5e_tx_reporter_timeout_dump+0x70/0x70 [mlx5_core]
? mlx5e_tx_reporter_dump_sq+0x320/0x320 [mlx5_core]
? mlx5e_tx_timeout_work+0x70/0x280 [mlx5_core]
? mutex_lock_io_nested+0x1320/0x1320
? process_one_work+0x70f/0x1340
? lockdep_hardirqs_on_prepare+0x400/0x400
? lock_downgrade+0x6e0/0x6e0
mlx5e_tx_timeout_work+0x1c1/0x280 [mlx5_core]
process_one_work+0x7c2/0x1340
? lockdep_hardirqs_on_prepare+0x400/0x400
? pwq_dec_nr_in_flight+0x230/0x230
? rwlock_bug.part.0+0x90/0x90
worker_thread+0x59d/0xec0
? process_one_work+0x1340/0x1340
kthread+0x28f/0x330
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Fixes: c90005b5f7 ("devlink: Hold the instance lock in health callbacks")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
IPsec FDB offload can only work with FW steering as of now,
disable the cap upon non FW steering.
And since the IPSec cap is dynamic now based on steering mode.
Cleanup the resources if they exist instead of checking the
IPsec cap again.
Fixes: edd8b295f9 ("Merge branch 'mlx5-ipsec-packet-offload-support-in-eswitch-mode'")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
After IPSec TX tables are destroyed, the flow rules in TC rhashtable,
which have the destination to IPSec, are restored to the original
one, the uplink.
However, when the device is in switchdev mode and unload driver with
IPSec rules configured, TC rhashtable cleanup is done before IPSec
cleanup, which means tc_ht->tbl is already freed when walking TC
rhashtable, in order to restore the destination. So add the checking
before walking to avoid unexpected behavior.
Fixes: d1569537a8 ("net/mlx5e: Modify and restore TC rules for IPSec TX rules")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Currently eswitch mode_lock is so heavy, for example, it's locked
during the whole process of the mode change, which may need to hold
other locks. As the mode_lock is also used by IPSec to block mode and
encap change now, it is easy to cause lock dependency.
Since some of protections are also done by devlink lock, the eswitch
mode_lock is not needed at those places, and thus the possibility of
lockdep issue is reduced.
Fixes: c8e350e62f ("net/mlx5e: Make TC and IPsec offloads mutually exclusive on a netdev")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
IPsec NAT-T packets are UDP encapsulated packets over ESP normal ones.
In case they arrive to RX, the SPI and ESP are located in inner header,
while the check was performed on outer header instead.
That wrong check caused to the situation where received rekeying request
was missed and caused to rekey timeout, which "compensated" this failure
by completing rekeying.
Fixes: d659549349 ("net/mlx5e: Support IPsec NAT-T functionality")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
After IPsec decryption it isn't enough to only check the IPsec syndrome
but need to also check the ASO syndrome in order to verify that the
operation was actually successful.
Verify that both syndromes are actually zero and in case not drop the
packet and increment the appropriate flow counter for the drop reason.
Fixes: 6b5c45e16e ("net/mlx5e: Configure IPsec packet offload flow steering")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
After previous commit, which unified various IPsec creation modes,
there is no need to have struct mlx5e_ipsec_rx exposed in global
IPsec header. Move it to ipsec_fs.c to be placed together with
already existing struct mlx5e_ipsec_tx.
Fixes: 1762f132d5 ("net/mlx5e: Support IPsec packet offload for RX in switchdev mode")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Change normal IPsec flow to use the same creation/destruction functions
for status flow table as that of ESW, which first of all refines the
code to have less code duplication.
And more importantly, the ESW status table handles IPsec syndrome
checks at steering by HW, which is more efficient than the previous
behaviour we had where it was copied to WQE meta data and checked
by the driver.
Fixes: 1762f132d5 ("net/mlx5e: Support IPsec packet offload for RX in switchdev mode")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
According to RFC4303, section "3.3.3. Sequence Number Generation",
the first packet sent using a given SA will contain a sequence
number of 1.
However if user didn't set seq/oseq, the HW used zero as first sequence
packet number. Such misconfiguration causes to drop of first packet
if replay window protection was enabled in SA.
To fix it, set sequence number to be at least 1.
Fixes: 7db21ef456 ("net/mlx5e: Set IPsec replay sequence numbers")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Users can configure IPsec replay window size, but mlx5 driver didn't
honor their choice and set always 32bits. Fix assignment logic to
configure right size from the beginning.
Fixes: 7db21ef456 ("net/mlx5e: Set IPsec replay sequence numbers")
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Commit 41a506ef71 ("powerpc/ftrace: Create a dummy stackframe to fix
stack unwind") added use of a new stack frame on ftrace entry to fix
stack unwind. However, the commit missed updating the offset used while
tearing down the ftrace stack when ftrace is disabled. Fix the same.
In addition, the commit missed saving the correct stack pointer in
pt_regs. Update the same.
Fixes: 41a506ef71 ("powerpc/ftrace: Create a dummy stackframe to fix stack unwind")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Naveen N Rao <naveen@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20231130065947.2188860-1-naveen@kernel.org
Rohan G Thomas says:
====================
net: stmmac: EST implementation
This patchset extends EST interrupt handling support to DWXGMAC IP
followed by refactoring of EST implementation. Added a separate
module for EST and moved all EST related functions to the new module.
Also added support for EST cycle-time-extension.
====================
Link: https://lore.kernel.org/r/20231201055252.1302-1-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for cycle-time-extension. TER GCL-register needs to be
updated with the cycle-time-extension. Width of TER register is EST
time interval width + 7 bits.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-4-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor EST implementation by moving common code for DWMAC4 and
DWXGMAC IPs into a separate EST module. EST implementation for DWMAC4
and DWXGMAC differs only for CSR base address, PTOV field offset
width, and PTOV clock multiplier value.
Thanks, Serge Semin and Jakub Kicinski for the suggestions on
refactoring EST implementation into a separate EST module.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-3-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enabled the following EST related interrupts:
1) Constant Gate Control Error (CGCE)
2) Head-of-Line Blocking due to Scheduling (HLBS)
3) Head-of-Line Blocking due to Frame Size (HLBF)
4) Base Time Register error (BTRE)
5) Switch to S/W owned list Complete (SWLC)
Also, add EST errors into the ethtool statistic.
The commit e49aa315cb ("net: stmmac: EST interrupts handling and
error reporting") and commit 9f29895919 ("net: stmmac: Add EST
errors into ethtool statistic") add EST interrupts handling and error
reporting support to DWMAC4 core. This patch enables the same support
for XGMAC.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-2-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current adaptive interrupt coalescing code updates only rx
packet stats for dim algorithm. This patch also updates tx packet
stats which will be useful when there is only tx traffic.
Also moved configuring hardware adaptive interrupt setting to
driver dim callback.
Fixes: 6e144b47f5 ("octeontx2-pf: Add support for adaptive interrupt coalescing")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231201053330.3903694-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drm/i915 fixes for v6.7-rc4 #2:
- d21a3962d3 ("drm/i915: Call intel_pre_plane_updates() also for pipes
getting enabled") in the previous fixes pull depends on a change that
wasn't included. Pick it up.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87fs0m48ol.fsf@intel.com
Amritha Nambiar says:
====================
Introduce queue and NAPI support in netdev-genl (Was: Introduce NAPI queues support)
Add the capability to export the following via netdev-genl interface:
- queue information supported by the device
- NAPI information supported by the device
Introduce support for associating queue and NAPI instance.
Extend the netdev_genl generic netlink family for netdev
with queue and NAPI data.
The queue parameters exposed are:
- queue index
- queue type
- ifindex
- NAPI id associated with the queue
Additional rx and tx queue parameters can be exposed in follow up
patches by stashing them in netdev queue structures. XDP queue type
can also be supported in future.
The NAPI fields exposed are:
- NAPI id
- NAPI device ifindex
- Interrupt number associated with the NAPI instance
- PID for the NAPI thread
This series only supports 'get' ability for retrieving
certain queue and NAPI attributes. The 'set' ability for
configuring queue and associated NAPI instance via netdev-genl
will be submitted as a separate patch series.
Previous discussion at:
https://lore.kernel.org/netdev/c8476530638a5f4381d64db0e024ed49c2db3b02.camel@gmail.com/T/#m00999652a8b4731fbdb7bf698d2e3666c65a60e7
$ ./cli.py --spec netdev.yaml --do queue-get --json='{"ifindex": 12, "id": 0, "type": 0}'
{'id': 0, 'ifindex': 12, 'napi-id': 593, 'type': 'rx'}
$ ./cli.py --spec netdev.yaml --do queue-get --json='{"ifindex": 12, "id": 0, "type": 1}'
{'id': 0, 'ifindex': 12, 'napi-id': 593, 'type': 'tx'}
$ ./cli.py --spec netdev.yaml --dump queue-get --json='{"ifindex": 12}'
[{'id': 0, 'ifindex': 12, 'napi-id': 593, 'type': 'rx'},
{'id': 1, 'ifindex': 12, 'napi-id': 594, 'type': 'rx'},
{'id': 2, 'ifindex': 12, 'napi-id': 595, 'type': 'rx'},
{'id': 3, 'ifindex': 12, 'napi-id': 596, 'type': 'rx'},
{'id': 0, 'ifindex': 12, 'napi-id': 593, 'type': 'tx'},
{'id': 1, 'ifindex': 12, 'napi-id': 594, 'type': 'tx'},
{'id': 2, 'ifindex': 12, 'napi-id': 595, 'type': 'tx'},
{'id': 3, 'ifindex': 12, 'napi-id': 596, 'type': 'tx'}]
$ ./cli.py --spec netdev.yaml --do napi-get --json='{"id": 593}'
{'id': 593, 'ifindex': 12, 'irq': 291, 'pid': 3727}
$ ./cli.py --spec netdev.yaml --dump napi-get --json='{"ifindex": 12}'
[{'id': 596, 'ifindex': 12, 'irq': 294, 'pid': 3724},
{'id': 595, 'ifindex': 12, 'irq': 293, 'pid': 3725},
{'id': 594, 'ifindex': 12, 'irq': 292, 'pid': 3726},
{'id': 593, 'ifindex': 12, 'irq': 291, 'pid': 3727}]
====================
Link: https://lore.kernel.org/r/170147307026.5260.9300080745237900261.stgit@anambiarhost.jf.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>