The VOP on RK3328 needs to run at a higher rate in order to produce a
proper 3840x2160 signal.
Change to use 300MHz for VIO clk and 400MHz for VOP clk, same rates used
by vendor 4.4 kernel.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240615170417.3134517-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3588j uses a different set of OPPs for its GPU, both in terms of
allowed frequencies and in terms of voltages.
Move the GPU OPPs table into per-variant .dtsi files to accommodate
for this difference.
The table for RK3588j is adapted from Rockchip downstream sources [1],
while RK3588 one is moved verbatim into the per-variant .dtsi file.
The values provided for RK3588 in the downstream sources match those
in the original commit.
[1] 604cec4004/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
Fixes: 6fca4edb93 ("arm64: dts: rockchip: Add rk3588 GPU node")
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-8-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3588j is the 'industrial' variant of RK3588, and it uses a different
set of OPPs both in terms of allowed frequencies and in terms of
applicable voltages at each frequency setpoint.
Add the OPPs that apply to RK3588j (and apparently RK3588m too) to
enable dynamic CPU frequency scaling.
OPP values are derived from Rockchip downstream sources [1] by taking
only those OPPs which have the highest frequency for a given voltage
level and dropping the rest (if they are included, the kernel complains
at boot time about them being inefficient)
[1] 604cec4004/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-7-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
By default the CPUs on RK3588 start up in a conservative performance
mode. Add frequency and voltage mappings to the device tree to enable
dynamic scaling via cpufreq.
OPP values are adapted from Radxa's downstream kernel for Rock 5B [1],
stripping them down to the minimum frequency and voltage combinations
as expected by the generic upstream cpufreq-dt driver, and also dropping
those OPPs that don't differ in voltage but only in frequency (keeping
the top frequency OPP in each case).
Note that this patch ignores voltage scaling for the CPU memory
interface which the downstream kernel does through a custom cpufreq
driver, and which is why the downstream version has two sets of voltage
values for each OPP (the second one being meant for the memory
interface supply regulator). This is done instead via regulator
coupling between CPU and memory interface supplies on affected boards.
This has been tested on Rock 5B with u-boot 2023.11 compiled from
Collabora's integration tree [2] with binary bl31 and appears to be
stable both under active cooling and passive cooling (with throttling)
[1] https://github.com/radxa/kernel/blob/stable-5.10-rock5/arch/arm64/boot/dts/rockchip/rk3588s.dtsi
[2] https://gitlab.collabora.com/hardware-enablement/rockchip-3588/u-boot
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-6-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3588 chips allow for their CPU cores to be powered by a different
supply vs. their corresponding memory interfaces, and two of the
boards currently upstream do that (EVB1 and QuartzPro64).
The voltage of the memory interface though has to match that of the
CPU cores that use it, which downstream kernels achieve by the means
of a custom cpufreq driver which adjusts both at the same time.
It seems that regulator coupling is a more appropriate generic
interface for it, so this patch introduces coupling to affected
device trees to ensure that memory interface voltage is also updated
whenever cpufreq switches between CPU OPPs.
Note that other boards, such as Radxa Rock 5B, define both the CPU
and memory interface regulators as aliases to the same DT node, so
this doesn't apply there.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-5-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
align with other Radxa products.
- mmc0 is eMMC
- mmc1 is microSD
for ZERO 3E, there is no eMMC, but aliases should start at 0, so mmc0
is microSD as exception.
Fixes: 1a5c8d307c ("arm64: dts: rockchip: Add Radxa ZERO 3W/3E")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Changes in v3:
- fix syntax error in rk3566-radxa-zero-3e.dts
Changes in v2:
- microSD is mmc0 instead of mmc1 for ZERO 3E
Link: https://lore.kernel.org/r/20240620224435.2752-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The PinePhone Pro has a cluster of 3 single RGB GPIO LEDs.
Add the GPIO entries for the 3 red/green/blue LEDs and an
entry for the multi-color group to allow them to be used
as a combined RGB LED.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20240623165326.1273944-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit adds SFC node for Radxa ROCK 5A.
since sdhci and sfc on RK3588s share pins(i.e. exclusive), it cannot
be enabled both nodes at the same time. so status = "okay" is omitted
here.
you may be able to enable sfc (and disable sdhci) by fdt overlay.
SPI NOR flash chip may vary, so use safe(lowest) spi-max-frequency.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20240623023329.1044-2-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit adds support for SPI NOR flash on Radxa ROCK 5B.
SPI NOR flash chip may vary, so use safe(lowest) spi-max-frequency.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20240623023329.1044-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This links the PWM fan on Radxa Rock 5B as an active cooling device
managed automatically by the thermal subsystem, with a target SoC
temperature of 65C and a minimum-spin interval from 55C to 65C to
ensure airflow when the system gets warm
Helped-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-4-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As the GPU support on RK3588 has been merged upstream, along with OPP
values, add a corresponding cooling map for passive cooling using the GPU.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-3-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables the on-chip thermal monitoring sensor (TSADC) on all
RK3588(s) boards that don't have it enabled yet. It provides temperature
monitoring for the SoC and emergency thermal shutdowns, and is thus
important to have in place before CPU DVFS is enabled, as high CPU
operating performance points can overheat the chip quickly in the
absence of thermal management.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-2-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This includes the necessary device tree data to allow thermal
monitoring on RK3588(s) using the on-chip TSADC device, along with
trip points for automatic thermal management.
Each of the CPU clusters (one for the little cores and two for
the big cores) get a passive cooling trip point at 85C, which
will trigger DVFS throttling of the respective cluster upon
reaching a high temperature condition.
All zones also have a critical trip point at 115C, which will
trigger a reset.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20240617-rk-dts-additions-v5-1-c1f5f3267f1e@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rename the Rockchip RK3588 SoC dtsi files and, consequently, adjust their
contents appropriately, to prepare them for the ability to specify different
CPU and GPU OPPs for each of the supported RK3588 SoC variants.
As already discussed, [1][2][3][4] some of the RK3588 SoC variants require
different OPPs, and it makes more sense to have the OPPs already defined when
a board dts(i) file includes one of the SoC variant dtsi files (rk3588.dtsi,
rk3588j.dtsi or rk3588s.dtsi), rather than requiring the board dts(i) file
to also include a separate rk3588*-opp.dtsi file. The choice of the SoC
variant is already made by the inclusion of the SoC dtsi file into the board
dts(i) file, and it doesn't make much sense to, effectively, allow the board
dts(i) file to include and use an incompatible set of OPPs for the already
selected RK3588 SoC variant.
The new naming scheme for the RK3588 SoC dtsi files uses "-base" and "-extra"
suffixes to denote the DT data shared between all RK5588 SoC variants, and
the DT data shared between the unrestricted SoC variants, respectively.
For example, the DT data for the RK3588 includes both rk3588-base.dtsi and
rk3588-extra.dtsi, because it's an unrestricted SoC variant, while the DT
data for the RK3588S variant includes rk3588-base.dtsi only, because it's
a restricted SoC variant, feature- and interface-wise. This achieves a more
logical naming of the RK3588 SoC dtsi files, which reflects the way DT data
for the SoC variants is built by "stacking" the SoC variant features made
available through the "-base" and "-extra" SoC dtsi files. Additionally,
the SoC variant dtsi files (rk3588.dtsi, rk3588j.dtsi and rk3588s.dtsi) are
no longer parents to any other SoC variant dtsi files, which should help with
making the new "stacking" approach cleaner and easier to follow.
The RK3588 pinctrl dtsi files are also renamed in the same way, for the sake
of consistency. This also keeps the "-base" and "-extra" groups of the dtsi
files together when looked at in a directory listing, which is helpful.
The per-SoC-variant OPPs should go directly into the SoC dtsi files, if no
more than one SoC variant uses those OPPs, or be put into a separate "-opp"
dtsi file that's shared between and included from two or more SoC variant
dtsi files. An example for the former is the non-shared OPP data that should
go directly into the RK3588J SoC variant dtsi file (i.e. rk3588j.dtsi), and
an example for the latter is the shared OPP data that should be put into
rk3588-opp.dtsi and be included from the RK3588 and RK3588S SoC variant dtsi
files (i.e. rk3588.dtsi and rk3588s.dtsi, respectively). Consequently, if
the OPPs for the RK3588 and RK3588S SoC variants are ever made different,
the shared rk3588-opp.dtsi file should be deleted and the new OPPs should
be put directly into rk3588.dtsi and rk3588s.dtsi. [4]
No functional changes are introduced, which was validated by decompiling and
comparing all affected dtb files before and after these changes.
As a side note, due to the nature of introduced changes, this commit is best
viewed using the --break-rewrites option for git-log(1).
[1] https://lore.kernel.org/linux-rockchip/646a33e0-5c1b-471c-8183-2c0df40ea51a@cherry.de/
[2] https://lore.kernel.org/linux-rockchip/CABjd4Yxi=+3gkNnH3BysUzzYsji-=-yROtzEc8jM_g0roKB0-w@mail.gmail.com/
[3] https://lore.kernel.org/linux-rockchip/035a274be262528012173d463e25b55f@manjaro.org/
[4] https://lore.kernel.org/linux-rockchip/673dcf47596e7bc8ba065034e339bb1bbf9cdcb0.1716948159.git.dsimic@manjaro.org/T/#u
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/9ffedc0e2ca7f167d9d795b2a8f43cb9f56a653b.1717923308.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on
the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
To reflect the hardware setup, add device tree sources for the SoM and
the NAS daughter board as separate files.
Hardware features:
- Rockchip RK3588 SoC
- 4GB/8GB/16GB LPDDR4x RAM
- 64GB eMMC
- MicroSD card slot
- 1x RTL8125B 2.5G Ethernet
- 4x M.2 M-Key with PCIe 3.0 x1 (via bifurcation) for NVMe SSDs
- 2x USB 3.0 (USB 3.1 Gen1) Type-A, 1x USB 2.0 Type-A
- 1x USB 3.0 Type-C with DP AltMode support
- 2x HDMI 2.1 out, 1x HDMI in
- MIPI-CSI Connector, MIPI-DSI Connector
- 40-pin GPIO header
- 4 buttons: power, reset, recovery, MASK, user button
- 3.5mm Headphone out, 2.0mm PH-2A Mic in
- 5V Fan connector, PWM beeper, IR receiver, RTC battery connector
PCIe bifurcation is used to handle all four M.2 sockets at PCIe 3.0 x1
speed. Data lane mapping in the DT is done like described in commit
f8020dfb31 ("phy: rockchip-snps-pcie3: fix bifurcation on rk3588").
This device tree includes support for eMMC, SD card, ethernet, all USB2
and USB3 ports, all four M.2 slots, GPU, beeper, IR, RTC, UART debugging
as well as the buttons and LEDs.
The GPIOs are labeled according to the schematics.
Reviewed-by: Space Meyer <git@the-space.agency>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Link: https://lore.kernel.org/r/20240616215354.40999-3-seb-dev@mail.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree bindings for the FriendlyElec CM3588 NAS board.
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based on
the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
Link: https://lore.kernel.org/r/20240616215354.40999-2-seb-dev@mail.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In case of legacy cursor update, the cursor VMA needs to be unpinned
only after vblank. This exceeds the lifetime of the whole atomic commit.
Any trick I attempted to keep the atomic commit alive didn't work, as
drm_atomic_helper_setup_commit() force throttles on any old commit that
wasn't cleaned up.
The only option remaining is to remove the plane from the atomic commit,
and use the same path as the legacy cursor update to clean the state
after vblank.
Changes since previous version:
- Call the memset for plane state immediately when scheduling vblank,
this prevents a use-after-free in cursor cleanup.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240522053341.137592-4-maarten.lankhorst@linux.intel.com
The cursor hardware only does sync updates, and thus the hardware
will be scanning out from the old fb until the next start of vblank.
So in order to make the legacy cursor fastpath actually safe we
should not unpin the old fb until we're sure the hardware has
ceased accessing it. The simplest approach is to just use a vblank
work here to do the delayed unpin.
Not 100% sure it's a good idea to put this onto the same high
priority vblank worker as eg. our timing critical gamma updates.
But let's keep it simple for now, and it we later discover that
this is causing problems we can think about adding a lower
priority worker for such things.
This patch is slightly reworked by Maarten
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240522053341.137592-3-maarten.lankhorst@linux.intel.com
In some cases we want to flush all vblank work, right before vblank_off
for example. Add a simple function to make this possible.
Check that both pending_work and running work are empty when flushing.
Co-Developed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240522053341.137592-2-maarten.lankhorst@linux.intel.com
The Kconfig for platforms/arm64 has 'depends on ARM64 || COMPILE_TEST'.
However due to Makefile having just obj-$(CONFIG_ARM64) the subdir will
not be descended for !ARM64 platforms and thus the drivers won't get
built. This breaks modular builds of other driver drivers which depend
on arm64 platform drivers.
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 363c8aea25 ("platform: Add ARM64 platform directory")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240624-ucsi-yoga-ec-driver-v9-1-53af411a9bd6@linaro.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
According to the hardware design, the i2c address of audio codec es8316
on Cool Pi 4B is 0x10.
This fix the read/write error like bellow:
es8316 7-0011: ASoC: error at soc_component_write_no_lock on es8316.7-0011 for register: [0x0000000c] -6
es8316 7-0011: ASoC: error at soc_component_write_no_lock on es8316.7-0011 for register: [0x00000003] -6
es8316 7-0011: ASoC: error at soc_component_read_no_lock on es8316.7-0011 for register: [0x00000016] -6
es8316 7-0011: ASoC: error at soc_component_read_no_lock on es8316.7-0011 for register: [0x00000016] -6
Fixes: 3f5d336d64 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20240623115526.2154645-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
EMail addresses of both maintainers bounce. Since there have been only
cleanups for the last 10 years, let it fall back to the default MMC
entry.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240621101833.24703-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The email address bounced. I couldn't find a newer one in recent git
history, so update MAINTAINERS accordingly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix flags in X1 Yoga example. MEDIA_LNK_FL_DYNAMIC (0x4 in the link flag)
was removed in V4 Intel IPU6 and IPU6 input system drivers. Added -V flag
to media-ctl commands for X1 Yoga, lower-case v only makes it verbose
upper-case V sets the format.
Signed-off-by: Samuel Wein <sam@samwein.com>
[Sakari Ailus: Align subject line, rewrap commit message.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a V4L2 sub-device driver for Galaxycore GC05A2 image sensor.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
[Sakari Ailus: Fold in MAINTAINERS change.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add YAML device tree binding for GC05A2 CMOS image sensor,
and the relevant MAINTAINERS entries.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a V4L2 sub-device driver for Galaxycore GC08A3 image sensor.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
[Sakari Ailus: Fold in MAINTAINERS change.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add YAML device tree binding for GC08A3 CMOS image sensor,
and the relevant MAINTAINERS entries.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
KCSAN has identified a potential data race in debugobjects, where the
global variable debug_objects_maxchain is accessed for both reading and
writing simultaneously in separate and parallel data paths. This results in
the following splat printed by KCSAN:
BUG: KCSAN: data-race in debug_check_no_obj_freed / debug_object_activate
write to 0xffffffff847ccfc8 of 4 bytes by task 734 on cpu 41:
debug_object_activate (lib/debugobjects.c:199 lib/debugobjects.c:564 lib/debugobjects.c:710)
call_rcu (kernel/rcu/rcu.h:227 kernel/rcu/tree.c:2719 kernel/rcu/tree.c:2838)
security_inode_free (security/security.c:1626)
__destroy_inode (./include/linux/fsnotify.h:222 fs/inode.c:287)
...
read to 0xffffffff847ccfc8 of 4 bytes by task 384 on cpu 31:
debug_check_no_obj_freed (lib/debugobjects.c:1000 lib/debugobjects.c:1019)
kfree (mm/slub.c:2081 mm/slub.c:4280 mm/slub.c:4390)
percpu_ref_exit (lib/percpu-refcount.c:147)
css_free_rwork_fn (kernel/cgroup/cgroup.c:5357)
...
value changed: 0x00000070 -> 0x00000071
The data race is actually harmless as this is just used for debugfs
statistics, as all other debug variables.
Annotate all debug variables as racy explicitly, since these variables
are known to be racy and harmless.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240611091813.1189860-1-leitao@debian.org
Commit ca78476e48 ("mfd: Remove toshiba tmio drivers") removed the
last users of the .set_pwr() callback in the tmio_mmc_data structure.
Remove the callback, and all related infrastructure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/fbbc13ddd19df2c40933ffa3b82fb14841bf1d4c.1718897545.git.geert+renesas@glider.be
Commit bef64d2908 ("mmc: remove tmio_mmc driver") removed the last
user of the .set_clk_div() callback in the tmio_mmc_data structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/e0fa98f138a7b2836128178f8b3a757978517307.1718897545.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set a timeout for MKHI client send operations in the bus fixup routines
to prevent potential lock-ups on the cl_bus_lock mutex.
In rare conditions, such as when the i915 or Xe driver is stopping and
not routing interrupts or when GSC FW is in unexpectedly reset the fixup
routines can get stuck.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240615063159.1460290-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With slab accounting, allocating and freeing memory has considerable
overhead. Add a basic alloc cache for the io_kiocb allocations that
msg_ring needs to do. Unlike other caches, this one is used by the
sender, grabbing it from the remote ring. When the remote ring gets
the posted completion, it'll free it locally. Hence it is separately
locked, using ctx->msg_lock.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the exported helper for queueing task_work for message passing,
rather than rolling our own.
Note that this is only done for strict data messages for now, file
descriptor passing messages still rely on the kernel task_work. It could
get converted at some point if it's performance critical.
This improves peak performance of message passing by about 5x in some
basic testing, with 2 threads just sending messages to each other.
Before this change, it was capped at around 700K/sec, with the change
it's at over 4M/sec.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This helper will post a CQE, and can be called from task_work where we
now that the ctx is already properly locked and that deferred
completions will get flushed later on.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All our task_work handling is targeted at the state in the io_kiocb
itself, which is what it is being used for. However, MSG_RING rolls its
own task_work handling, ignoring how that is usually done.
In preparation for switching MSG_RING to be able to use the normal
task_work handling, add io_req_task_work_add_remote() which allows the
caller to pass in the target io_ring_ctx.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently this is gated on whether or not the target ring needs a local
completion - and if so, whether or not we're running on the right task.
The use case for same thread cross posting is probably a lot less
relevant than remote posting. And since we're going to improve this
situation anyway, just gate it on local posting and ignore what task
we're currently running on.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
make allmodconfig && make W=1 C=1 reports:
modpost: missing MODULE_DESCRIPTION() in drivers/block/brd.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240602-md-block-brd-v1-1-e71338e131b6@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Raspberry Pi devices have to date all used ARCH_BCM2835
as their SoC arch dependency so configurations that use this
and not BRCMSTB won't end up with this module in their config.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/20240620074248.152353-1-pbrobinson@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
