Add the C3 peripherals clock controller driver in the C3 SoC family.
[jbrunet: fix Kconfig select order and probe function name]
Co-developed-by: Chuan Liu <chuan.liu@amlogic.com>
Signed-off-by: Chuan Liu <chuan.liu@amlogic.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/r/20240522082727.3029656-6-xianwei.zhao@amlogic.com
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Fix the 'make W=1' kernel-doc warning:
drivers/hid/intel-ish-hid/ishtp/bus.c:853: warning: Function parameter or struct member 'dev' not described in 'ishtp_wait_resume'
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311060843.dXENYlGc-lkp@intel.com/
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Show more info for interrupt only lines in debugfs. It's useful
to monitor the lines that have been never requested as GPIOs,
but IRQs.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240530191418.1138003-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Currently, HUION devices use ABS_WHEEL as the usage for touch strips.
There are 2 main issues with this approach:
The first one is that the descriptor for touch rings
(uclogic_rdesc_v2_frame_touch_ring_arr) also uses ABS_WHEEL.
>From user-space it is impossible to know which device sends the events.
The second one is that Wacom uses ABS_RX/ABS_RY to notify events from
touch strips and user-space was designed to handle those axes.
Change the usage of touch strips to Rx/Ry to fix both issues.
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/989
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The HID descriptor for HUION tablets was limited to 13 buttons. However,
there are devices with more buttons in their frames.
So far, the device with more buttons released by HUION is the Huion
Kamvas Pro 24 (GT-240, QHD) [1], with 20 buttons.
Tweak the HID descriptor to support it.
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/989 [1]
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The function hid_register_field() might allocate more than 32k, which
would use order-4 contiguous memory if the parameter usage exceeds
1024. However, after the system runs for a while, the memory can
become heavily fragmented. This increases the likelihood of order-4 page
allocation failure. Here’s the relevant log.
[71553.093623]kworker/1: 0: page allocation failure: order:4, mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0
[71553.093669]Workqueue: events uhid_device_add_worker
[71553.093683]Call trace:
[71553.093687]: dump_backtrace+0xf4/0x118
[71553.093696]: show_stack+0x18/0x24
[71553.093702]: dump_stack_lvl+0x60/0x7c
[71553.093710]: dump_stack+0x18/0x3c
[71553.093717]: warn_alloc+0xf4/0x174
[71553.093725]: __alloc_pages_slowpath+0x1ba0/0x1cac
[71553.093732]: __alloc_pages+0x460/0x560
[71553.093738]: __kmalloc_large_node+0xbc/0x1f8
[71553.093746]: __kmalloc+0x144/0x254
[71553.093752]: hid_add_field+0x13c/0x308
[71553.093758]: hid_parser_main+0x250/0x298
[71553.093765]: hid_open_report+0x214/0x30c
[71553.093771]: mt_probe+0x130/0x258
[71553.093778]: hid_device_probe+0x11c/0x1e4
[71553.093784]: really_probe+0xe4/0x388
[71553.093791]: __driver_probe_device+0xa0/0x12c
[71553.093798]: driver_probe_device+0x44/0x214
[71553.093804]: __device_attach_driver+0xdc/0x124
[71553.093812]: bus_for_each_drv+0x88/0xec
[71553.093818]: __device_attach+0x84/0x170
[71553.093824]: device_initial_probe+0x14/0x20
[71553.093831]: bus_probe_device+0x48/0xd0
[71553.093836]: device_add+0x248/0x928
[71553.093844]: hid_add_device+0xf8/0x1a4
[71553.093850]: uhid_device_add_worker+0x24/0x144
[71553.093857]: process_one_work+0x158/0x804
[71553.093865]: worker_thread+0x15c/0x494
[71553.093872]: kthread+0xf4/0x1e4
[71553.093880]: ret_from_fork+0x10/0x20
To fix the allocation failure, use kvzalloc() instead of kzalloc().
Signed-off-by: Hailong.Liu <hailong.liu@oppo.com>
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Syzkaller hit a warning [1] in a call to implement() when trying
to write a value into a field of smaller size in an output report.
Since implement() already has a warn message printed out with the
help of hid_warn() and value in question gets trimmed with:
...
value &= m;
...
WARN_ON may be considered superfluous. Remove it to suppress future
syzkaller triggers.
[1]
WARNING: CPU: 0 PID: 5084 at drivers/hid/hid-core.c:1451 implement drivers/hid/hid-core.c:1451 [inline]
WARNING: CPU: 0 PID: 5084 at drivers/hid/hid-core.c:1451 hid_output_report+0x548/0x760 drivers/hid/hid-core.c:1863
Modules linked in:
CPU: 0 PID: 5084 Comm: syz-executor424 Not tainted 6.9.0-rc7-syzkaller-00183-gcf87f46fd34d #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
RIP: 0010:implement drivers/hid/hid-core.c:1451 [inline]
RIP: 0010:hid_output_report+0x548/0x760 drivers/hid/hid-core.c:1863
...
Call Trace:
<TASK>
__usbhid_submit_report drivers/hid/usbhid/hid-core.c:591 [inline]
usbhid_submit_report+0x43d/0x9e0 drivers/hid/usbhid/hid-core.c:636
hiddev_ioctl+0x138b/0x1f00 drivers/hid/usbhid/hiddev.c:726
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:904 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:890
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Fixes: 95d1c8951e ("HID: simplify implement() a bit")
Reported-by: <syzbot+5186630949e3c55f0799@syzkaller.appspotmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Looks like drivers/crypto/vmx/.gitignore should have been merged into
arch/powerpc/crypto/.gitignore as part of commit
109303336a ("crypto: vmx - Move to arch/powerpc/crypto") so that all
generated asm files are ignored.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Fixes: 109303336a ("crypto: vmx - Move to arch/powerpc/crypto")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240603-powerpc-crypto-ignore-p8-asm-v1-1-05843fec2bb7@linux.ibm.com
It is preferred to use sizeof(*pointer) instead of sizeof(type)
due to the type of the variable can change and one needs not
change the former (unlike the latter). This patch has no effect
on runtime behavior.
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/auxdisplay/hd44780_common.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/auxdisplay/line-display.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Like we do for charlcd, allow the configuration of the initial message
on line-display devices.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's not an error or noteworthy condition if the
"ibm,dynamic-reconfiguration-memory" node isn't present.
Drop the needless message.
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240603-silence-drmem_init-v1-1-e9d71646bc3d@linux.ibm.com
VAS allocate, modify and deallocate HCALLs returns
H_LONG_BUSY_ORDER_1_MSEC or H_LONG_BUSY_ORDER_10_MSEC for busy
delay and expects OS to reissue HCALL after that delay. But using
msleep() will often sleep at least 20 msecs even though the
hypervisor suggests OS reissue these HCALLs after 1 or 10msecs.
The open and close VAS window functions hold mutex and then issue
these HCALLs. So these operations can take longer than the
necessary when multiple threads issue open or close window APIs
simultaneously, especially might affect the performance in the
case of repeat open/close APIs for each compression request.
Multiple tasks can open / close VAS windows at the same time
which depends on the available VAS credits. For example, 240
cores system provides 4800 VAS credits. It means 4800 tasks can
execute open VAS windows HCALLs with the mutex. Since each
msleep() will often sleep more than 20 msecs, some tasks are
waiting more than 120 secs to acquire mutex. It can cause hung
traces for these tasks in dmesg due to mutex contention around
open/close HCALLs.
Instead of msleep(), use usleep_range() to ensure sleep with
the expected value before issuing HCALL again. So since each
task sleep 10 msecs maximum, this patch allow more tasks can
issue open/close VAS calls without any hung traces in the
dmesg.
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Suggested-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240116055910.421605-1-haren@linux.ibm.com
In the current design, a numa-node is made online only if that node is
attached to cpu/memory. With this design, if any PCI/IO device is found
to be attached to a numa-node which is not online then the numa-node
id of the corresponding PCI/IO device is set to NUMA_NO_NODE(-1). This
design may negatively impact the performance of PCIe device if the
numa-node assigned to PCIe device is -1 because in such case we may not
be able to accurately calculate the distance between two nodes.
The multi-controller NVMe PCIe disk has an issue with calculating the
node distance if the PCIe NVMe controller is attached to a PCI host
bridge which has numa-node id value set to NUMA_NO_NODE. This patch
helps fix this ensuring that a cpu/memory less numa node is made online
if it's attached to PCI host bridge.
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240517142531.3273464-3-nilay@linux.ibm.com
Dynamic DMA Window (DDW) supports TCEs that are backed by 2MB page
size. In most configurations, DDW is big enough to pre-map all of LPAR
memory for IO. Pre-mapping of memory for DMA results in improvements in
IO performance.
Persistent memory, vPMEM, can be assigned to an LPAR as well. vPMEM is
not contiguous with LPAR memory and usually is assigned at high memory
addresses. This makes is not possible to pre-map both vPMEM and LPAR
memory in the same DDW.
For a dedicated adapter this limitation is not an issue. Dedicated
adapters can have both Default DMA window, which is backed by 4K page
size and a DDW backed by 2MB page size TCEs. In this scenario, LPAR
memory is pre-mapped in the DDW. Any DMA going to the vPMEM is routed
via dynamically allocated TCEs in the default window.
The issue arises with SR-IOV adapters. There is only one DMA window -
either Default or DDW. If an LPAR has vPMEM assigned, memory is not
pre-mapped in the DDW since TCEs needs to be allocated for vPMEM as well.
In this case, DDW is created and TCEs are dynamically allocated for both
vPMEM and LPAR memory.
Today, DDW is only used in single mode - direct mapped TCEs or
dynamically mapped TCEs. This enhancement breaks a single DDW in 2
regions -
1. First region to pre-map LPAR memory
2. Second region to dynamically allocate TCEs for IO to vPMEM
The DDW is split only if it is big enough to pre-map complete LPAR
memory and still have some space left to dynamically map vPMEM. Maximum
size possible DDW is created as permitted by the Hypervisor.
Signed-off-by: Gaurav Batra <gbatra@linux.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240514014608.35537-1-gbatra@linux.ibm.com
On an Amiga 1200 equipped with a Warp1260 accelerator, an interrupt
storm coming from the accelerator board causes the machine to crash in
local_irq_enable() or auto_irq_enable(). Disabling interrupts for the
Warp1260 in amiga_parse_bootinfo() fixes the problem.
Link: https://lore.kernel.org/r/ZkjwzVwYeQtyAPrL@amaterasu.local
Cc: stable <stable@kernel.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20240601153254.186225-1-p.pisati@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Drop privacy-LED GPIO control, after the privacy-LED GPIO control was added
to the ov5693 driver it was decided to model privacy-LEDs as LED class
devices and have them be controlled by the v4l2-core.
So this is dead code since on devices with privacy LEDs the led is not
a GPIO on the ov5693 fwnode, but rather is a LED class devices controlled
by the v4l2-core.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping the CSI source before stopping the serializer
CSI port may make the serializer not respond.
Then all the next writes to the device will fail.
max96717 1-0040: Error writing reg 0x0308: -121
max96717 1-0040: Error writing reg 0x0006: -121
Fix that by stopping the CSI receiver first and then CSI source.
Seen on max96717f revision 4.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This driver handles the MAX96714 deserializer in tunnel mode.
The CSI output will replicate all the CSI traffic forwarded by
the remote serializer.
The MAX96714 driver can handle MAX96714 and MAX96714F variants
with the same "maxim,max96714f" compatible.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
[Sakari Ailus: Adapt to changed i2c_mux_add_adapter arguments.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This driver handles the MAX96717 serializer in tunnel mode.
All incoming CSI traffic will be tunneled through the GMSL2
link.
The MAX96717 driver can handle MAX96717 and MAX96717F variants
with the same "maxim,max96717f" compatible.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
[Sakari Ailus: Adapt to changed i2c_mux_add_adapter arguments.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Several subdev state pointers are used to access the state read-only.
Mark them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It would be useful to mark instances of v4l2_subdev_state structures as
const when code needs to access them read-only. This isn't currently
possible, as the v4l2_subdev_state_get_*() accessor functions take a
non-const pointer to the state.
Use _Generic() to provide two different versions of the accessors, for
const and non-const states respectively. The former returns a const
pointer to the requested format, rectangle or interval, implementing
const-correctness. The latter returns a non-const pointer, preserving
the current behaviour for drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[Sakari Ailus: Drop the word "below" from the text.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The documentation of the v4l2_subdev_state_get_format() macro
incorrectly references __v4l2_subdev_state_get_format() instead of
__v4l2_subdev_state_gen_call(). Fix it, and also update the list of
similar macros to add the missing v4l2_subdev_state_get_interval().
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Always assign *val to 0 in cci_read(). This has the benefit of not
requiring initialisation of the variables data is read to using
cci_read(). Once smatch is fixed, it could catch the use of uninitialised
reads.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It's entirely normal CSR will return non-indicative values after its reset
(0). There's no need to warn the user about that.
Suggested-by: Bingbu Cao <bingbu.cao@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'i2c_reg_value' is unused since the original
commit 5a544cce21 ("[media] adv7511: add new video encoder").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'regval_list' has been unused since
commit 398994c1e1 ("V4L/DVB (13666): tw9910: modify V/H outpit pin
setting to use VALID").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'adjust' has been unused since original
commit fbe60daac4 ("V4L/DVB (3916): AverMedia 6 Eyes AVS6EYES
support").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'regval_list' is unused since the original
commit 859891228e ("media: i2c: dw9768: Add DW9768 VCM driver")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a v4l2 subdevice driver for the Sony IMX283 image sensor.
The IMX283 is a 20MP Diagonal 15.86 mm (Type 1) CMOS Image Sensor with
Square Pixel for Color Cameras.
The following features are supported:
- Manual exposure an gain control support
- vblank/hblank/link freq control support
- Test pattern support control
- Arbitrary horizontal and vertical cropping
- Supported resolution:
- 5472x3648 @ 20fps (SRGGB12)
- 5472x3648 @ 25fps (SRGGB10)
- 2736x1824 @ 50fps (SRGGB12)
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
[Sakari Ailus: Take upstream runtime PM API changes into account.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Now that enable/disable_streams operations are available for
single-stream subdevices too, there's no reason to use the old s_stream
operation on new drivers. Extend the documentation reflecting this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Umang Jain<umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
At the moment v4l2_subdev_s_stream_helper() only works for subdevices
that support routing. As enable/disable_streams now also works for
subdevices without routing, improve v4l2_subdev_s_stream_helper() to do
the same.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
At the moment the v4l2_subdev_enable/disable_streams() functions call
fallback helpers to handle the case where the subdev only implements
.s_stream(), and the main function handles the case where the subdev
implements streams (V4L2_SUBDEV_FL_STREAMS, which implies
.enable/disable_streams()).
What is missing is support for subdevs which do not implement streams
support, but do implement .enable/disable_streams(). Example cases of
these subdevices are single-stream cameras, where using
.enable/disable_streams() is not required but helps us remove the users
of the legacy .s_stream(), and subdevices with multiple source pads (but
single stream per pad), where .enable/disable_streams() allows the
subdevice to control the enable/disable state per pad.
The two single-streams cases (.s_stream() and .enable/disable_streams())
are very similar, and with small changes we can change the
v4l2_subdev_enable/disable_streams() functions to support all three
cases, without needing separate fallback functions.
A few potentially problematic details, though:
- For the single-streams cases we use sd->enabled_pads field, which
limits the number of pads for the subdevice to 64. For simplicity I
added the check for this limitation to the beginning of the function,
and it also applies to the streams case.
- The fallback functions only allowed the target pad to be a source pad.
It is not very clear to me why this check was needed, but it was not
needed in the streams case. However, I doubt the
v4l2_subdev_enable/disable_streams() code has ever been tested with
sink pads, so to be on the safe side, I added the same check
to the v4l2_subdev_enable/disable_streams() functions.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add two internal helper functions, v4l2_subdev_collect_streams() and
v4l2_subdev_set_streams_enabled(), which allows us to refactor
v4l2_subdev_enable/disable_streams() functions.
This (I think) makes the code a bit easier to read, and lets us more
easily add new functionality in the helper functions in the following
patch.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
We support camera privacy leds with the .s_stream() operation, in
call_s_stream(), but we don't have that support when the subdevice
implements .enable/disable_streams() operations.
Add the support by enabling the led when the first stream for a
subdevice is enabled, and disabling the led then the last stream is
disabled.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a helper function which returns whether the subdevice is streaming,
i.e. if .s_stream or .enable_streams has been called successfully.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
v4l2_subdev_enable/disable_streams_fallback() supports falling back to
.s_stream() for subdevs with a single source pad. It also tracks the
enabled streams for that one pad in the sd->enabled_streams field.
Tracking the enabled streams with sd->enabled_streams does not make
sense, as with .s_stream() there can only be a single stream per pad.
Thus, as the v4l2_subdev_enable/disable_streams_fallback() only supports
a single source pad, all we really need is a boolean which tells whether
streaming has been enabled on this pad or not.
However, as we only need a true/false state for a pad (instead of
tracking which streams have been enabled for a pad), we can easily
extend the fallback mechanism to support multiple source pads as we only
need to keep track of which pads have been enabled.
Change the sd->enabled_streams field to sd->enabled_pads, which is a
64-bit bitmask tracking the enabled source pads. With this change we can
remove the restriction that
v4l2_subdev_enable/disable_streams_fallback() only supports a single
source pad.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
call_s_stream() uses sd->enabled_streams to track whether streaming has
already been enabled. However,
v4l2_subdev_enable/disable_streams_fallback(), which was the original
user of this field, already uses it, and
v4l2_subdev_enable/disable_streams_fallback() will call call_s_stream().
This leads to a conflict as both functions set the field. Afaics, both
functions set the field to the same value, so it won't cause a runtime
bug, but it's still wrong and if we, e.g., change how
v4l2_subdev_enable/disable_streams_fallback() operates we might easily
cause bugs.
Fix this by adding a new field, 's_stream_enabled', for
call_s_stream().
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add some checks to verify that the subdev driver implements required
features.
A subdevice that supports streams (V4L2_SUBDEV_FL_STREAMS) must do one
of the following:
- Implement neither .enable/disable_streams() nor .s_stream(), if the
subdev is part of a video driver that uses an internal method to
enable the subdev.
- Implement only .enable/disable_streams(), if support for legacy
sink-side subdevices is not needed.
- Implement .enable/disable_streams() and .s_stream(), if support for
legacy sink-side subdevices is needed.
At the moment the framework doesn't check this requirement. Add the
check.
Reviewed-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
