The Allwinner A64's GPU has currently three operating points. However,
the BSP runs the GPU fixed at 432 MHz. In addition, at least one of the
devices using that SoC - the pinephone - shows unstabilities (see link)
that can be circumvented by running the GPU at a fixed rate.
Therefore, remove the other two operating points from the GPU OPP table,
so that the GPU runs at a fixed rate of 432 MHz.
Link: https://gitlab.com/postmarketOS/pmaports/-/issues/805
Acked-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240310-pinephone-pll-fixes-v4-5-46fc80c83637@oltmanns.dev
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens. Use also generic name for pwrseq
node, because generic naming is favored by Devicetree spec. All the
clocks affected by this change use clock-output-names, so resulting
clock name should not change. Functional impact checked with comparing
before/after DTBs with dtx_diff and fdtdump.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Delete node via phandle, not via full node path, to avoid easy mistakes
- if original node name changes, such deletion would be ineffective and
not reported by the dtc as error.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens. Use also generic name for pwrseq
node, because generic naming is favored by Devicetree spec. All the
clocks affected by this change use clock-output-names, so resulting
clock name should not change. Functional impact checked with comparing
before/after DTBs with dtx_diff and fdtdump.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
There is no "reg_gmac_3v3" device node in sun50i-h6-pine-h64.dts,
although there is "gmac-3v3" with "reg_gmac_3v3" label, so let's assume
author wanted to remove that node. Delete node via phandle, not via
full node path, to fix this.
Fixes: f33a911750 ("arm64: dts: allwinner: add pineh64 model B")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317184130.157695-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The red, green, and blue LEDs currently in the device tree represent a
single RGB LED on the front of the PinePhone.
Signed-off-by: Aren Moynihan <aren@peacevolution.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317004116.1473967-2-aren@peacevolution.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Allows user to set a LED before entering suspend to know that
the phone is still on (or could be used for notifications etc).
Signed-off-by: Miles Alan <m@milesalan.com>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Aren Moynihan <aren@peacevolution.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240317004116.1473967-1-aren@peacevolution.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
While PLL CPUX clock rate change when CPU is running from it works in
vast majority of cases, now and then it causes instability. This leads
to system crashes and other undefined behaviour. After a lot of testing
(30+ hours) while also doing a lot of frequency switches, we can't
observe any instability issues anymore when doing reparenting to stable
clock like 24 MHz oscillator.
Fixes: 524353ea48 ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Reported-by: Chad Wagner <wagnerch42@gmail.com>
Link: https://forum.libreelec.tv/thread/27295-orange-pi-3-lts-freezes/
Tested-by: Chad Wagner <wagnerch42@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20231013181712.2128037-1-jernej.skrabec@gmail.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Generate the mask of enabled L3 banks for the GT. It is stored with the
rest of the GT topology in a consistent representation across platforms.
For now the L3 bank mask is just printed in the log for developers to
easily figure out the fusing characteristics of machines that they are
trying to debug issues on. Later it can be used to replace existing code
in the driver that requires the L3 bank count (not mask). Also the mask
can easily be exposed to user space in a new query if needed.
v2: Better naming of variable and function (Matt Roper)
Bspec: 52545, 52546, 62482
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Francois Dugast <francois.dugast@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240410123723.7-2-francois.dugast@intel.com
These have no clear purpose. This is effectively a revert of commit
bb7462b6fd ("vfs: use helpers for calling f_op->{read,write}_iter()").
The patch was created with the help of a coccinelle script.
Fixes: bb7462b6fd ("vfs: use helpers for calling f_op->{read,write}_iter()")
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
should've been done as soon as overlayfs stopped messing with fake
paths...
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
always equal to ->dentry->d_inode of the path argument these
days.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
IS_ERR(NULL) is false and IS_ERR() already comes with unlikely()...
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
kmemleak complains that there's a memory leak related to connect
handling:
unreferenced object 0xffff0001093bdf00 (size 128):
comm "iou-sqp-455", pid 457, jiffies 4294894164
hex dump (first 32 bytes):
02 00 fa ea 7f 00 00 01 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 2e481b1a):
[<00000000c0a26af4>] kmemleak_alloc+0x30/0x38
[<000000009c30bb45>] kmalloc_trace+0x228/0x358
[<000000009da9d39f>] __audit_sockaddr+0xd0/0x138
[<0000000089a93e34>] move_addr_to_kernel+0x1a0/0x1f8
[<000000000b4e80e6>] io_connect_prep+0x1ec/0x2d4
[<00000000abfbcd99>] io_submit_sqes+0x588/0x1e48
[<00000000e7c25e07>] io_sq_thread+0x8a4/0x10e4
[<00000000d999b491>] ret_from_fork+0x10/0x20
which can can happen if:
1) The command type does something on the prep side that triggers an
audit call.
2) The thread hasn't done any operations before this that triggered
an audit call inside ->issue(), where we have audit_uring_entry()
and audit_uring_exit().
Work around this by issuing a blanket NOP operation before the SQPOLL
does anything.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This commit comes at the tail end of a greater effort to remove the
empty elements at the end of the ctl_table arrays (sentinels) which will
reduce the overall build time size of the kernel and run time memory
bloat by ~64 bytes per sentinel (further information Link :
https://lore.kernel.org/all/ZO5Yx5JFogGi%2FcBo@bombadil.infradead.org/)
Remove the sentinel from all files under security/ that register a
sysctl table.
Signed-off-by: Joel Granados <j.granados@samsung.com>
Acked-by: Kees Cook <keescook@chromium.org> # loadpin & yama
Tested-by: Valentin Schneider <vschneid@redhat.com>
Reviewed-by: Valentin Schneider <vschneid@redhat.com>
[PM: subject line tweaks]
Signed-off-by: Paul Moore <paul@paul-moore.com>
I didn't pay close enough attention the last time I tried to fix this
problem - while we currently do correctly take care to make sure we don't
probe a connected eDP port more then once, we don't do the same thing for
eDP ports we found to be disconnected.
So, fix this and make sure we only ever probe eDP ports once and then leave
them at that connector state forever (since without HPD, it's not going to
change on its own anyway). This should get rid of the last few GSP errors
getting spit out during runtime suspend and resume on some machines, as we
tried to reprobe eDP ports in response to ACPI hotplug probe events.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404233736.7946-3-lyude@redhat.com
(cherry picked from commit fe6660b661)
GSP has its own state for keeping track of whether or not a given display
connector is plugged in or not, and enforces this state on the driver. In
particular, AUX transactions on a DisplayPort connector which GSP says is
disconnected can never succeed - and can in some cases even cause
unexpected timeouts, which can trickle up to cause other problems. A good
example of this is runtime power management: where we can actually get
stuck trying to resume the GPU if a userspace application like fwupd tries
accessing a drm_aux_dev for a disconnected port. This was an issue I hit a
few times with my Slimbook Executive 16 - where trying to offload something
to the discrete GPU would wake it up, and then potentially cause it to
timeout as fwupd tried to immediately access the dp_aux_dev nodes for
nouveau.
Likewise: we don't really have any cases I know of where we'd want to
ignore this state and try an aux transaction anyway - and failing pointless
aux transactions immediately can even speed things up. So - let's start
enabling/disabling the aux bus in nouveau_dp_detect() to fix this. We
enable the aux bus during connector probing, and leave it enabled if we
discover something is actually on the connector. Otherwise, we just shut it
off.
This should fix some people's runtime PM issues (like myself), and also get
rid of quite of a lot of GSP error spam in dmesg.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404233736.7946-2-lyude@redhat.com
(cherry picked from commit 9c8a10bf1f)
Add a Python test for the basic ops.
# ./net/nl_netdev.py
KTAP version 1
1..3
ok 1 nl_netdev.empty_check
ok 2 nl_netdev.lo_check
ok 3 nl_netdev.page_pool_check
# Totals: pass:3 fail:0 xfail:0 xpass:0 skip:0 error:0
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20240412141436.828666-7-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using "with" on an entire driver test env is supported already,
but it's also useful to use "with" on an individual nsim.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20240412141436.828666-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of a summary line print the full exception.
This makes debugging Python tests much easier.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20240412141436.828666-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Developing Python tests is a bit annoying because when test fails
we only print the fail message and no info about which exact check
led to it. Print the location (the first line of this example is new):
# At /root/ksft-net-drv/./net/nl_netdev.py line 38:
# Check failed 0 != 10
not ok 3 nl_netdev.page_pool_check
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20240412141436.828666-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
YNL currently reports None for empty dump:
$ cli.py ...netdev.yaml --dump page-pool-get
None
This doesn't matter for the CLI but when writing YNL based tests
having to deal with either list or None is annoying. Limit the
None conversion to non-dump ops:
$ cli.py ...netdev.yaml --dump page-pool-get
[]
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240412141436.828666-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add very basic page pool use so that we can exercise
the netlink uAPI in a selftest.
Page pool gets created on open, destroyed on close.
But we control allocating of a single page thru debugfs.
This page may survive past the page pool itself so that
we can test orphaned page pools.
Link: https://lore.kernel.org/r/20240412141436.828666-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Breno Leitao says:
====================
net: dqs: optimize if stall threshold is not set
Here are four patches aimed at enhancing the Dynamic Queue Limit (DQL)
subsystem within the networking stack.
The first two commits involve code refactoring, while the third patch
introduces the actual change. The fourth patch just improves the cache
locality.
Typically, when DQL is enabled, stall information is always populated
through dql_queue_stall(). However, this information is only necessary
if a stall threshold is set, which is stored in struct dql->stall_thrs.
Although dql_queue_stall() is relatively inexpensive, it is not entirely
free due to memory barriers and similar overheads.
To optimize performance, refrain from calling dql_queue_stall() when no
stall threshold is set, thus avoiding the processing of unnecessary
information.
v1: https://lore.kernel.org/all/20240404145939.3601097-1-leitao@debian.org/
====================
Link: https://lore.kernel.org/r/20240411192241.2498631-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the previous change, struct dqs->stall_thrs will be in the hot path
(at queue side), even if DQS is disabled.
The other fields accessed in this function (last_obj_cnt and num_queued)
are in the first cache line, let's move this field (stall_thrs) to the
very first cache line, since there is a hole there.
This does not change the structure size, since it moves an short (2
bytes) to 4-bytes whole in the first cache line.
This is the new structure format now:
struct dql {
unsigned int num_queued;
unsigned int last_obj_cnt;
...
short unsigned int stall_thrs;
/* XXX 2 bytes hole, try to pack */
...
/* --- cacheline 1 boundary (64 bytes) --- */
...
/* Longest stall detected, reported to user */
short unsigned int stall_max;
/* XXX 2 bytes hole, try to pack */
};
Also, read the stall_thrs (now in the very first cache line) earlier,
together with dql->num_queued (also in the first cache line).
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240411192241.2498631-5-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When Dynamic Queue Limit (DQL) is set, it always populate stall
information through dql_queue_stall(). However, this information is
only necessary if a stall threshold is set, stored in struct
dql->stall_thrs.
dql_queue_stall() is cheap, but not free, since it does have memory
barriers and so forth.
Do not call dql_queue_stall() if there is no stall threshold set, and
save some CPU cycles.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240411192241.2498631-4-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dql_queued() function currently handles both queuing object counts
and populating bitmaps for reporting stalls.
This commit splits the bitmap population into a separate function,
allowing for conditional invocation in scenarios where the feature is
disabled.
This refactor maintains functionality while improving code
organization.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240411192241.2498631-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the dql_queued() function receives an invalid argument, WARN about it
and continue, instead of crashing the kernel.
This was raised by checkpatch, when I am refactoring this code (see
following patch/commit)
WARNING: Do not crash the kernel unless it is absolutely unavoidable--use WARN_ON_ONCE() plus recovery code (if feasible) instead of BUG() or variants
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240411192241.2498631-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recently we extended the binding for protocol@13 to allow it to be modelled
as a generic performance domain. In a way to promote using the new binding,
let's update the examples.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240403111106.1110940-1-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
kernel/configs/hardening.config turns on UBSAN for the bounds sanitizer,
as that in combination with trapping can stop the exploitation of buffer
overflows within the kernel. At the same time, hardening.config turns
off every other UBSAN sanitizer because trapping means all UBSAN reports
will be fatal and the problems brought up by other sanitizers generally
do not have security implications.
The signed integer overflow sanitizer was recently added back to the
kernel and it is default on with just CONFIG_UBSAN=y, meaning that it
gets enabled when merging hardening.config into another configuration.
While this sanitizer does have security implications like the array
bounds sanitizer, work to clean up enough instances to allow this to run
in production environments is still ramping up, which means regular
users and testers may be broken by these instances with
CONFIG_UBSAN_TRAP=y. Disable CONFIG_UBSAN_SIGNED_WRAP in
hardening.config to avoid this situation.
Fixes: 557f8c582a ("ubsan: Reintroduce signed overflow sanitizer")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240411-fix-ubsan-in-hardening-config-v1-2-e0177c80ffaa@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
The initial change that added kernel/configs/hardening.config attempted
to disable all UBSAN sanitizers except for the array bounds one while
turning on UBSAN_TRAP. Unfortunately, it only got the syntax for
CONFIG_UBSAN_SHIFT correct, so configurations that are on by default
with CONFIG_UBSAN=y such as CONFIG_UBSAN_{BOOL,ENUM} do not get disabled
properly.
CONFIG_ARCH_HAS_UBSAN=y
CONFIG_UBSAN=y
CONFIG_UBSAN_TRAP=y
CONFIG_CC_HAS_UBSAN_BOUNDS_STRICT=y
CONFIG_UBSAN_BOUNDS=y
CONFIG_UBSAN_BOUNDS_STRICT=y
# CONFIG_UBSAN_SHIFT is not set
# CONFIG_UBSAN_DIV_ZERO is not set
# CONFIG_UBSAN_UNREACHABLE is not set
CONFIG_UBSAN_SIGNED_WRAP=y
CONFIG_UBSAN_BOOL=y
CONFIG_UBSAN_ENUM=y
# CONFIG_TEST_UBSAN is not set
Add the missing 'is not set' to each configuration that needs it so that
they get disabled as intended.
CONFIG_ARCH_HAS_UBSAN=y
CONFIG_UBSAN=y
CONFIG_UBSAN_TRAP=y
CONFIG_CC_HAS_UBSAN_BOUNDS_STRICT=y
CONFIG_UBSAN_BOUNDS=y
CONFIG_UBSAN_BOUNDS_STRICT=y
# CONFIG_UBSAN_SHIFT is not set
# CONFIG_UBSAN_DIV_ZERO is not set
# CONFIG_UBSAN_UNREACHABLE is not set
CONFIG_UBSAN_SIGNED_WRAP=y
# CONFIG_UBSAN_BOOL is not set
# CONFIG_UBSAN_ENUM is not set
# CONFIG_TEST_UBSAN is not set
Fixes: 215199e3d9 ("hardening: Provide Kconfig fragments for basic options")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240411-fix-ubsan-in-hardening-config-v1-1-e0177c80ffaa@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
"ARCH_HAVE_EXTRA_ELF_NOTES" enables an extra note section in the
core dump. Kconfig variable is preferred over ARCH_HAVE_* macro.
Co-developed-by: Jini Susan George <jinisusan.george@amd.com>
Signed-off-by: Jini Susan George <jinisusan.george@amd.com>
Signed-off-by: Vignesh Balasubramanian <vigbalas@amd.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20240412062138.1132841-2-vigbalas@amd.com
Signed-off-by: Kees Cook <keescook@chromium.org>
various recovery fixes:
- fixes for the btree_insert_entry being resized on path allocation
btree_path array recently became dynamically resizable, and
btree_insert_entry along with it; this was being observed during
journal replay, when write buffer btree updates don't use the write
buffer and instead use the normal btree update path
- multiple fixes for deadlock in recovery when we need to do lots of
btree node merges; excessive merges were clocking up the whole
pipeline
- write buffer path now correctly does btree node merges when needed
- fix failure to go RW when superblock indicates recovery passes needed
(i.e. to complete an unfinished upgrade)
various unsafety fixes - test case contributed by a user who had two
drives out of a six drive array write out a whole bunch of garbage after
power failure
new (tiny) on disk format feature: since it appears the btree node scan
tool will be a more regular thing (crappy hardware, user error) - this
adds a 64 bit per-device bitmap of regions that have ever had btree
nodes.
a path->should_be_locked fix, from a larger patch series tightening up
invariants and assertions around btree transaction and path locking
state; this particular fix prevents us from keeping around btree_paths
that are no longer needed.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEKnAFLkS8Qha+jvQrE6szbY3KbnYFAmYdaRIACgkQE6szbY3K
bnbqcA/9ETT0Jekf/V4klQmoWj9GX5nQstUz+ENABNNPL+5hld62EojiRvOW2qwU
zVs7O0M59B8/+4v4KJoW+RqnLFjAF4z/Gf+/Uw9WarsHAKIxxFFFARxG93JpGqOn
nGa8RSw0BaYQIdbMR0Bdacc2f0N+JkJQx956/+JV7EG5MAJqXgz00AvIuLqMZ+2t
0m9av3n0tVmstyvvGqk8pouvQjK0XUvIDYN3oiUDl7WXOAIKXDlp6yviiGnTbusq
DssmIt5fdeVBq/DAk5PMNEKM9NUP+weIZW1UWPWINaicarqyV+pn2fhvLrBxVl7q
zBSN3v28viaABKC8A15b2bqj3IT2WIBDoBCEi406akMao9eiVsE6is13rFkPQwQI
Obhc7NNDyOPPTvX25M3tKXpr8rSGoD2qHIMMKMIBe1ZWscj6lMbmUBErwzTOAW4+
pNTvzWT2XwcS7tE8Fx50ZxcehTQl6ir0hQvjJL5JV2po8XMbdGxcImBe6xPmAa3n
/XIzyglL8IvW494wjCsHxtTeOt+f8nW7BXJCrWB71UQeXIXq4b9FADOwWtlGTnxJ
6XNprfi8TSp+RsSRxav6DBw2ou5viGjAjP2ddrO6Lw37XUYV0igS+BeDNEPA4dwI
ZlbCzNE7qSXK2rjmGjyu7GCJ3+NOxJDQ8GdxkTDtpPrBF2kCOkQ=
=NAId
-----END PGP SIGNATURE-----
Merge tag 'bcachefs-2024-04-15' of https://evilpiepirate.org/git/bcachefs
Pull yet more bcachefs fixes from Kent Overstreet:
"This gets recovery working again for the affected user I've been
working with, and I'm still waiting to hear back on other bug reports
but should fix it for everyone else who's been having issues with
recovery.
- Various recovery fixes:
- fixes for the btree_insert_entry being resized on path
allocation btree_path array recently became dynamically
resizable, and btree_insert_entry along with it; this was being
observed during journal replay, when write buffer btree updates
don't use the write buffer and instead use the normal btree
update path
- multiple fixes for deadlock in recovery when we need to do lots
of btree node merges; excessive merges were clocking up the
whole pipeline
- write buffer path now correctly does btree node merges when
needed
- fix failure to go RW when superblock indicates recovery passes
needed (i.e. to complete an unfinished upgrade)
- Various unsafety fixes - test case contributed by a user who had
two drives out of a six drive array write out a whole bunch of
garbage after power failure
- New (tiny) on disk format feature: since it appears the btree node
scan tool will be a more regular thing (crappy hardware, user
error) - this adds a 64 bit per-device bitmap of regions that have
ever had btree nodes.
- A path->should_be_locked fix, from a larger patch series tightening
up invariants and assertions around btree transaction and path
locking state.
This particular fix prevents us from keeping around btree_paths
that are no longer needed"
* tag 'bcachefs-2024-04-15' of https://evilpiepirate.org/git/bcachefs: (24 commits)
bcachefs: set_btree_iter_dontneed also clears should_be_locked
bcachefs: fix error path of __bch2_read_super()
bcachefs: Check for backpointer bucket_offset >= bucket size
bcachefs: bch_member.btree_allocated_bitmap
bcachefs: sysfs internal/trigger_journal_flush
bcachefs: Fix bch2_btree_node_fill() for !path
bcachefs: add safety checks in bch2_btree_node_fill()
bcachefs: Interior known are required to have known key types
bcachefs: add missing bounds check in __bch2_bkey_val_invalid()
bcachefs: Fix btree node merging on write buffer btrees
bcachefs: Disable merges from interior update path
bcachefs: Run merges at BCH_WATERMARK_btree
bcachefs: Fix missing write refs in fs fio paths
bcachefs: Fix deadlock in journal replay
bcachefs: Go rw if running any explicit recovery passes
bcachefs: Standardize helpers for printing enum strs with bounds checks
bcachefs: don't queue btree nodes for rewrites during scan
bcachefs: fix race in bch2_btree_node_evict()
bcachefs: fix unsafety in bch2_stripe_to_text()
bcachefs: fix unsafety in bch2_extent_ptr_to_text()
...
The commit 509433d814 ("drm/v3d: Expose the total GPU usage stats on sysfs")
introduced the calculation of global GPU stats. For the regards, it used
the already existing infrastructure provided by commit 09a93cc4f7 ("drm/v3d:
Implement show_fdinfo() callback for GPU usage stats"). While adding
global GPU stats calculation ability, the author forgot to delete the
existing one.
Currently, the value of `enabled_ns` is incremented twice by the end of
the job, when it should be added just once. Therefore, delete the
leftovers from commit 509433d814 ("drm/v3d: Expose the total GPU usage
stats on sysfs").
Fixes: 509433d814 ("drm/v3d: Expose the total GPU usage stats on sysfs")
Reported-by: Tvrtko Ursulin <tursulin@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240403203517.731876-2-mcanal@igalia.com
synchronize_rcu() users have to be processed regardless
of memory pressure so our private WQ needs to have at least
one execution context what WQ_MEM_RECLAIM flag guarantees.
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
This patch introduces a small enhancement which allows to do a
direct wake-up of synchronize_rcu() callers. It occurs after a
completion of grace period, thus by the gp-kthread.
Number of clients is limited by the hard-coded maximum allowed
threshold. The remaining part, if still exists is deferred to
a main worker.
Link: https://lore.kernel.org/lkml/Zd0ZtNu+Rt0qXkfS@lothringen/
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Add an rcu_sr_normal() trace event. It takes three arguments
first one is the name of RCU flavour, second one is a user id
which triggeres synchronize_rcu_normal() and last one is an
event.
There are two traces in the synchronize_rcu_normal(). On entry,
when a new request is registered and on exit point when request
is completed.
Please note, CONFIG_RCU_TRACE=y is required to activate traces.
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
A call to a synchronize_rcu() can be optimized from a latency
point of view. Workloads which depend on this can benefit of it.
The delay of wakeme_after_rcu() callback, which unblocks a waiter,
depends on several factors:
- how fast a process of offloading is started. Combination of:
- !CONFIG_RCU_NOCB_CPU/CONFIG_RCU_NOCB_CPU;
- !CONFIG_RCU_LAZY/CONFIG_RCU_LAZY;
- other.
- when started, invoking path is interrupted due to:
- time limit;
- need_resched();
- if limit is reached.
- where in a nocb list it is located;
- how fast previous callbacks completed;
Example:
1. On our embedded devices i can easily trigger the scenario when
it is a last in the list out of ~3600 callbacks:
<snip>
<...>-29 [001] d..1. 21950.145313: rcu_batch_start: rcu_preempt CBs=3613 bl=28
...
<...>-29 [001] ..... 21950.152578: rcu_invoke_callback: rcu_preempt rhp=00000000b2d6dee8 func=__free_vm_area_struct.cfi_jt
<...>-29 [001] ..... 21950.152579: rcu_invoke_callback: rcu_preempt rhp=00000000a446f607 func=__free_vm_area_struct.cfi_jt
<...>-29 [001] ..... 21950.152580: rcu_invoke_callback: rcu_preempt rhp=00000000a5cab03b func=__free_vm_area_struct.cfi_jt
<...>-29 [001] ..... 21950.152581: rcu_invoke_callback: rcu_preempt rhp=0000000013b7e5ee func=__free_vm_area_struct.cfi_jt
<...>-29 [001] ..... 21950.152582: rcu_invoke_callback: rcu_preempt rhp=000000000a8ca6f9 func=__free_vm_area_struct.cfi_jt
<...>-29 [001] ..... 21950.152583: rcu_invoke_callback: rcu_preempt rhp=000000008f162ca8 func=wakeme_after_rcu.cfi_jt
<...>-29 [001] d..1. 21950.152625: rcu_batch_end: rcu_preempt CBs-invoked=3612 idle=....
<snip>
2. We use cpuset/cgroup to classify tasks and assign them into
different cgroups. For example "backgrond" group which binds tasks
only to little CPUs or "foreground" which makes use of all CPUs.
Tasks can be migrated between groups by a request if an acceleration
is needed.
See below an example how "surfaceflinger" task gets migrated.
Initially it is located in the "system-background" cgroup which
allows to run only on little cores. In order to speed it up it
can be temporary moved into "foreground" cgroup which allows
to use big/all CPUs:
cgroup_attach_task():
-> cgroup_migrate_execute()
-> cpuset_can_attach()
-> percpu_down_write()
-> rcu_sync_enter()
-> synchronize_rcu()
-> now move tasks to the new cgroup.
-> cgroup_migrate_finish()
<snip>
rcuop/1-29 [000] ..... 7030.528570: rcu_invoke_callback: rcu_preempt rhp=00000000461605e0 func=wakeme_after_rcu.cfi_jt
PERFD-SERVER-1855 [000] d..1. 7030.530293: cgroup_attach_task: dst_root=3 dst_id=22 dst_level=1 dst_path=/foreground pid=1900 comm=surfaceflinger
TimerDispatch-2768 [002] d..5. 7030.537542: sched_migrate_task: comm=surfaceflinger pid=1900 prio=98 orig_cpu=0 dest_cpu=4
<snip>
"Boosting a task" depends on synchronize_rcu() latency:
- first trace shows a completion of synchronize_rcu();
- second shows attaching a task to a new group;
- last shows a final step when migration occurs.
3. To address this drawback, maintain a separate track that consists
of synchronize_rcu() callers only. After completion of a grace period
users are deferred to a dedicated worker to process requests.
4. This patch reduces the latency of synchronize_rcu() approximately
by ~30-40% on synthetic tests. The real test case, camera launch time,
shows(time is in milliseconds):
1-run 542 vs 489 improvement 9%
2-run 540 vs 466 improvement 13%
3-run 518 vs 468 improvement 9%
4-run 531 vs 457 improvement 13%
5-run 548 vs 475 improvement 13%
6-run 509 vs 484 improvement 4%
Synthetic test(no "noise" from other callbacks):
Hardware: x86_64 64 CPUs, 64GB of memory
Linux-6.6
- 10K tasks(simultaneous);
- each task does(1000 loops)
synchronize_rcu();
kfree(p);
default: CONFIG_RCU_NOCB_CPU: takes 54 seconds to complete all users;
patch: CONFIG_RCU_NOCB_CPU: takes 35 seconds to complete all users.
Running 60K gives approximately same results on my setup. Please note
it is without any interaction with another type of callbacks, otherwise
it will impact a lot a default case.
5. By default it is disabled. To enable this perform one of the
below sequence:
echo 1 > /sys/module/rcutree/parameters/rcu_normal_wake_from_gp
or pass a boot parameter "rcutree.rcu_normal_wake_from_gp=1"
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Co-developed-by: Neeraj Upadhyay (AMD) <neeraj.iitr10@gmail.com>
Signed-off-by: Neeraj Upadhyay (AMD) <neeraj.iitr10@gmail.com>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
The rcuc-starvation output from print_cpu_stall_info() might overflow the
buffer if there is a huge difference in jiffies difference. The situation
might seem improbable, but computers sometimes get very confused about
time, which can result in full-sized integers, and, in this case,
buffer overflow.
Also, the unsigned jiffies difference is printed using %ld, which is
normally for signed integers. This is intentional for debugging purposes,
but it is not obvious from the code.
This commit therefore changes sprintf() to snprintf() and adds a
clarifying comment about intention of %ld format.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 245a629825 ("rcu: Dump rcuc kthread status for CPUs not reporting quiescent state")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
When using "guard(rcu)();" sparse will complain, because even
though it now understands the cleanup attribute, it doesn't
evaluate the calls from it at function exit, and thus doesn't
count the context correctly.
Given that there's a conditional in the resulting code:
static inline void class_rcu_destructor(class_rcu_t *_T)
{
if (_T->lock) {
rcu_read_unlock();
}
}
it seems that even trying to teach sparse to evalulate the
cleanup attribute function it'd still be difficult to really
make it understand the full context here.
Suppress the sparse warning by just releasing the context in
the acquisition part of the function, after all we know it's
safe with the guard, that's the whole point of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
There is a possibility of buffer overflow in
show_rcu_tasks_trace_gp_kthread() if counters, passed
to sprintf() are huge. Counter numbers, needed for this
are unrealistically high, but buffer overflow is still
possible.
Use snprintf() with buffer size instead of sprintf().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: edf3775f0a ("rcu-tasks: Add count for idle tasks on offline CPUs")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
The synchronize_srcu() has been removed by commit("rcu-tasks: Eliminate
deadlocks involving do_exit() and RCU tasks") in rcu_tasks_postscan.
This commit therefore fixes the tasks_rcu_exit_srcu_stall_timer comment.
Signed-off-by: Zqiang <qiang.zhang1211@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Because the Tasks RCU ->rtp_exit_list is initialized at rcu_init()
time while there is only one CPU running with interrupts disabled, it
is not possible for an exiting task to encounter an uninitialized list.
This commit therefore replaces the conditional initialization with
a WARN_ON_ONCE().
Reported-by: Frederic Weisbecker <frederic@kernel.org>
Closes: https://lore.kernel.org/all/ZdiNXmO3wRvmzPsr@lothringen/
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
crc checksums are used to validate the output. Normally they're part
of the actual display hardware but on virtual stack there's nothing
to automatically generate them.
Implement crc generation for the vmwgfx stack. This works only on
screen targets, where it's possibly to easily make sure that the
guest side contents of the surface matches the host sides output.
Just like the vblank support, crc generation can only be enabled via:
guestinfo.vmwgfx.vkms_enable = "TRUE"
option in the vmx file.
Makes IGT's kms_pipe_crc_basic pass and allows a huge number of other
IGT tests which require CRC generation of the output to actually run
on vmwgfx. Makes it possible to actually validate a lof of the kms and
drm functionality with vmwgfx.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Acked-by: Martin Krastev <martin.krastev@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412025511.78553-3-zack.rusin@broadcom.com
By default vmwgfx doesn't support vblanking or crc generation which
makes it impossible to use various IGT tests to validate vmwgfx.
Implement virtual kernel mode setting, which is mainly related to
simulated vblank support.
Code is very similar to amd's vkms and the vkms module itself, except
that it's integrated with vmwgfx three different output technologies -
legacy, screen object and screen targets.
Make IGT's kms_vblank pass on vmwgfx and allows a lot of other IGT
tests to run with vmwgfx.
Support for vkms needs to be manually enabled by adding:
guestinfo.vmwgfx.vkms_enable = "TRUE"
somewhere in the vmx file, otherwise it's off by default.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Acked-by: Martin Krastev <martin.krastev@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240412025511.78553-2-zack.rusin@broadcom.com
This is part of a larger series cleaning up the semantics of
should_be_locked and adding assertions around it; if we don't need an
iterator/path anymore, it clearly doesn't need to be locked.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
