Xe graphics driver uses different graphics sysfs knobs including
/sys/class/drm/card0/device/tile0/gt0/gtidle/idle_residency_ms
/sys/class/drm/card0/device/tile0/gt0/freq0/cur_freq
/sys/class/drm/card0/device/tile0/gt0/freq0/act_freq
/sys/class/drm/card0/device/tile0/gt1/gtidle/idle_residency_ms
/sys/class/drm/card0/device/tile0/gt1/freq0/cur_freq
/sys/class/drm/card0/device/tile0/gt1/freq0/act_freq
Plus that,
/sys/class/drm/card0/device/tile0/gt<n>/gtidle/name
returns either gt<n>-rc or gt<n>-mc. rc is for GFX and mc is SA Media.
Enhance turbostat to prefer the Xe sysfs knobs when they are available.
Export gt<n>-rc via BIC_GFX_rc6/BIC_GFXMHz/BIC_GFXACTMHz.
Export gt<n>-mc via BIC_SMA_mc6/BIC_SMAMHz/BIC_SMAACTMHz.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
On Meteorlake platform, i915 driver supports the traditional graphics
sysfs knobs including
/sys/class/drm/card0/power/rc6_residency_ms
/sys/class/drm/card0/gt_cur_freq_mhz
/sys/class/drm/card0/gt_act_freq_mhz
At the same time, it also supports
/sys/class/drm/card0/gt/gt0/rc6_residency_ms
/sys/class/drm/card0/gt/gt0/rps_cur_freq_mhz
/sys/class/drm/card0/gt/gt0/rps_act_freq_mhz
/sys/class/drm/card0/gt/gt1/rc6_residency_ms
/sys/class/drm/card0/gt/gt1/rps_cur_freq_mhz
/sys/class/drm/card0/gt/gt1/rps_act_freq_mhz
gt0 is for GFX and gt1 is for SA Media.
Enhance turbostat to prefer the i915 new sysfs knobs.
Export gt0 via BIC_GFX_rc6/BIC_GFXMHz/BIC_GFXACTMHz.
Export gt1 via BIC_SMA_mc6/BIC_SMAMHz/BIC_SMAACTMHz.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Graphics driver (i915/Xe) on mordern platforms splits GFX and SA Media
information via different sysfs knobs.
Existing BIC_GFX_rc6/BIC_GFXMHz/BIC_GFXACTMHz columns can be reused for
GFX.
Introduce BIC_SAM_mc6/BIC_SAMMHz/BIC_SAMACTMHz columns for SA Media.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/63c9d1e6b07296916e4218c63f59a2dd6c6b6b16.1712732665.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/c7d669d8b0c994c77fb4c3bc7bec78aeb8659c74.1712732665.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/adb9b0aca77d7aa8e54d0a664a4ee290834a60a1.1712732665.git.u.kleine-koenig@pengutronix.de
Core in platform_driver_register() already sets the .owner, so driver
does not need to. Whatever is set here will be anyway overwritten by
main driver calling platform_driver_register().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240330202804.83936-1-krzysztof.kozlowski@linaro.org
An overflow can occur in a situation where src.centiseconds
takes the value of 255. This situation is unlikely, but there
is no validation check anywere in the code.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Roman Smirnov <r.smirnov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240327132755.13945-1-r.smirnov@omp.ru>
Since K230 has been supported, allow ARCH_CANAAN to be selected to build dt
and drivers for it in defconfig.
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The ARCH_ and SOC_ versions of this symbol have persisted for quite a
while now in parallel. Generated .config files from previous LTS kernels
should have both. Finally remove SOC_VIRT and update all config files
using it.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
All the users in the kernel are gone and generated .config files from
previous LTS kernels will contain ARCH_SIFIVE. Drop SOC_SIFIVE and
update the defconfig.
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
SOC_MICROCHIP_POLARFIRE doesn't have any remaining in-kernel users, so
time has come to remove it. Foolish auld me left the "POLARFIRE" in the
new, hidden, config option when I renamed it and changed all of the
users however. As HPSC has been announced, and is not a PolarFire,
drop mention of that specific FPGA family from the new user-visible
config option.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Binding devm_led_classdev_register() to the netdev is problematic
because on module removal we get a RTNL-related deadlock. Fix this
by avoiding the device-managed LED functions.
Note: We can safely call led_classdev_unregister() for a LED even
if registering it failed, because led_classdev_unregister() detects
this and is a no-op in this case.
Fixes: 18764b883e ("r8169: add support for LED's on RTL8168/RTL8101")
Cc: stable@vger.kernel.org
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SR-IOV PF mode detection is based on PCI capability as reported by
the PCI dev_is_pf() function and additionally on 'max_vfs' module
parameter which could be also used to disable PF capability even
if SR-IOV PF capability is reported by the hardware.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404154431.583-3-michal.wajdeczko@intel.com
We want to have an option to limit the number of the VFs that the
PF driver will be able to manage. With this limit set to zero we
will also have a way to completely disable the PF functionality.
Since we currently don't support SR-IOV on any platform, we start
with this limit set to zero by default.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404154431.583-2-michal.wajdeczko@intel.com
We may leave pat.ops unset when running on brand new platform or
when running as a VF. While the former is unlikely, the latter
is valid (future) use case and will cause NPD when someone will
try to dump PAT settings by debugfs.
It's better to check pointer to pat.ops instead of specific .dump
hook, as we have this hook always defined for every .ops variant.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240409105106.1067-2-michal.wajdeczko@intel.com
Make sure that pat.ops (if selected) has all required function
pointers setup. Only .program_media may be omitted if we have
older media version.
This should help avoid late runtime checks against individual
function pointers.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Piotr Piórkowski <piotr.piorkowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240409105106.1067-1-michal.wajdeczko@intel.com
tick_do_timer_cpu is used lockless to check which CPU needs to take care
of the per tick timekeeping duty. This is done to avoid a thundering
herd problem on jiffies_lock.
The read and writes are not annotated so KCSAN complains about data races:
BUG: KCSAN: data-race in tick_nohz_idle_stop_tick / tick_nohz_next_event
write to 0xffffffff8a2bda30 of 4 bytes by task 0 on cpu 26:
tick_nohz_idle_stop_tick+0x3b1/0x4a0
do_idle+0x1e3/0x250
read to 0xffffffff8a2bda30 of 4 bytes by task 0 on cpu 16:
tick_nohz_next_event+0xe7/0x1e0
tick_nohz_get_sleep_length+0xa7/0xe0
menu_select+0x82/0xb90
cpuidle_select+0x44/0x60
do_idle+0x1c2/0x250
value changed: 0x0000001a -> 0xffffffff
Annotate them with READ/WRITE_ONCE() to document the intentional data race.
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/87cyqy7rt3.ffs@tglx
The rt9455_boost_voltage_values[] array is only used when USB PHY
support is enabled, causing a W=1 warning otherwise:
drivers/power/supply/rt9455_charger.c:200:18: error: 'rt9455_boost_voltage_values' defined but not used [-Werror=unused-const-variable=]
Enclose the definition in the same #ifdef as the references to it.
Fixes: e86d69dd78 ("power_supply: Add support for Richtek RT9455 battery charger")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-10-arnd@kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).
While there add the missing kernel-doc for tb_switch_resume().
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently we don't configure correctly the wake events after unplug of device
router. What can happen is that the downstream ports of host router will be
configured to wake on: USB4-wake and wake-on-disconnect, but not on
wake-on-connect. This may cause the later plugged device not to wake the
domain and fail in enumeration. Fix this by clearing downstream port's "USB4
Port is Configured" bit, after unplug of a device router.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to setup the DSI clock, let's make the unused VCLK2 clock path
configuration via CCF.
The nocache option is removed from following clocks:
- vclk2_sel
- vclk2_input
- vclk2_div
- vclk2
- vclk_div1
- vclk2_div2_en
- vclk2_div4_en
- vclk2_div6_en
- vclk2_div12_en
- vclk2_div2
- vclk2_div4
- vclk2_div6
- vclk2_div12
- cts_encl_sel
vclk2 and vclk2_div uses the newly introduced vclk regmap driver
to handle the enable and reset bits.
In order to set a rate on cts_encl via the vclk2 clock path,
the NO_REPARENT flag is set on cts_encl_sel & vclk2_sel in order
to keep CCF from selection a parent.
The parents of cts_encl_sel & vclk2_sel are expected to be defined
in DT or manually set by the display driver at some point.
The following clock scheme is to be used for DSI:
xtal
\_ gp0_pll_dco
\_ gp0_pll
|- vclk2_sel
| \_ vclk2_input
| \_ vclk2_div
| \_ vclk2
| \_ vclk2_div1
| \_ cts_encl_sel
| \_ cts_encl -> to VPU LCD Encoder
|- mipi_dsi_pxclk_sel
\_ mipi_dsi_pxclk_div
\_ mipi_dsi_pxclk -> to DSI controller
The mipi_dsi_pxclk_div is set as bypass with a single /1 entry in div_table
in order to use the same GP0 for mipi_dsi_pxclk and vclk2_input.
The SET_RATE_PARENT is only set on the mipi_dsi_pxclk_sel clock so the
DSI bitclock is the reference base clock to calculate the vclk2_div value
when pixel clock is set on the cts_encl endpoint.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240403-amlogic-v6-4-upstream-dsi-ccf-vim3-v12-3-99ecdfdc87fc@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The VCLK and VCLK_DIV clocks have supplementary bits.
The VCLK gate has a "SOFT RESET" bit to toggle after the whole
VCLK sub-tree rate has been set, this is implemented in
the gate enable callback.
The VCLK_DIV clocks as enable and reset bits used to disable
and reset the divider, associated with CLK_SET_RATE_GATE it ensures
the rate is set while the divider is disabled and in reset mode.
The VCLK_DIV enable bit isn't implemented as a gate since it's part
of the divider logic and vendor does this exact sequence to ensure
the divider is correctly set.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240403-amlogic-v6-4-upstream-dsi-ccf-vim3-v12-2-99ecdfdc87fc@linaro.org
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Khadas Edge 2 exposes IR receiver pins as same as TF card via EXTIO. The
IR receiver is connected to MCU and SoC.
The board also has 2 PWM RGB leds. One is controlled by MCU and the
other is controlled by SoC. This commit adds support for the led
controlled by SoC using pwm-leds.
Signed-off-by: Muhammed Efe Cetin <efectn@protonmail.com>
Link: https://lore.kernel.org/r/335629f57e593e20418a4a55a1e662505640cbde.1708381247.git.efectn@protonmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When the driver notices fw_status == 0xff it tries to perform a PCI
reset on itself via pci_reset_function() in the context of the driver's
health thread. However, pdsc_reset_prepare calls
pdsc_stop_health_thread(), which attempts to stop/flush the health
thread. This results in a deadlock because the stop/flush will never
complete since the driver called pci_reset_function() from the health
thread context. Fix by changing the pdsc_check_pci_health_function()
to queue a newly introduced pdsc_pci_reset_thread() on the pdsc's
work queue.
Unloading the driver in the fw_down/dead state uncovered another issue,
which can be seen in the following trace:
WARNING: CPU: 51 PID: 6914 at kernel/workqueue.c:1450 __queue_work+0x358/0x440
[...]
RIP: 0010:__queue_work+0x358/0x440
[...]
Call Trace:
<TASK>
? __warn+0x85/0x140
? __queue_work+0x358/0x440
? report_bug+0xfc/0x1e0
? handle_bug+0x3f/0x70
? exc_invalid_op+0x17/0x70
? asm_exc_invalid_op+0x1a/0x20
? __queue_work+0x358/0x440
queue_work_on+0x28/0x30
pdsc_devcmd_locked+0x96/0xe0 [pds_core]
pdsc_devcmd_reset+0x71/0xb0 [pds_core]
pdsc_teardown+0x51/0xe0 [pds_core]
pdsc_remove+0x106/0x200 [pds_core]
pci_device_remove+0x37/0xc0
device_release_driver_internal+0xae/0x140
driver_detach+0x48/0x90
bus_remove_driver+0x6d/0xf0
pci_unregister_driver+0x2e/0xa0
pdsc_cleanup_module+0x10/0x780 [pds_core]
__x64_sys_delete_module+0x142/0x2b0
? syscall_trace_enter.isra.18+0x126/0x1a0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7fbd9d03a14b
[...]
Fix this by preventing the devcmd reset if the FW is not running.
Fixes: d9407ff118 ("pds_core: Prevent health thread from running during reset/remove")
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With default dts configuration for BPI-R2Pro, the regulator for sd card is
powered off when reboot is commanded, and the only solution to detect the
sd card again, and therefore, allow rebooting from there, is to do a
hardware reset.
Configure the regulator for sd to be always on for BPI-R2Pro in order to
avoid this issue.
Fixes: f901aaadaa ("arm64: dts: rockchip: Add Bananapi R2 Pro")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240305143222.189413-1-jtornosm@redhat.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the GameForce Chi, which is a handheld gaming console
from GameForce with a Rockchip RK3326 SoC. The device has a 640x480
3.5" dual-lane DSI display, one analog joystick connected to the SoC
SARADC controller and a second analog joystick connected to an unknown
UART based ADC, a single SD card slot, a single USB-C port for
charging, and onboard RTL8723BS WiFi/Bluetooth combo, multiple face
buttons, and an array of R/G/B LEDs used for key backlighting.
The vendor was unable to provide details on the unknown UART based
ADC which I have documented via a comment in the device-tree, and
the vendor also does not have available Bluetooth firmware (the BT
was not previously working on the vendor's OS, this has also been
noted in a device-tree comment).
Aside from the right analog ADC joystick and bluetooth all hardware has
been tested and is working as expected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240325134959.11807-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The GameForce Chi is a handheld gaming device from GameForce powered
by the Rockchip RK3326 SoC.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240325134959.11807-5-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
