The completion notification for the final SET_NOTIFICATION_ENABLE
command during initialization can include a connector change
notification. However, at the time this completion notification is
processed, the ucsi struct is not ready to handle this notification.
As a result the notification is ignored and the controller
never sends an interrupt again.
Re-check CCI for a pending connector state change after
initialization is complete. Adjust the corresponding debug
message accordingly.
Fixes: 71a1fa0df2 ("usb: typec: ucsi: Store the notification mask")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose we sleep on the PPM lock after clearing the EVENT_PENDING
bit because the thread for another connector is executing a command.
In this case the command completion of the other command will still
report the connector change for our connector.
Clear the EVENT_PENDING bit under the PPM lock to avoid another
useless call to ucsi_handle_connector_change() in this case.
Fixes: c9aed03a0a ("usb: ucsi: Add missing ppm_lock")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The attribute writing should return the number of bytes used from the
buffer on success.
Fixes: a7cff92f06 ("usb: typec: USB Power Delivery helpers for ports and partners")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240319074309.3306579-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible trigger below warning message from mass storage function,
WARNING: CPU: 6 PID: 3839 at drivers/usb/gadget/udc/core.c:294 usb_ep_queue+0x7c/0x104
pc : usb_ep_queue+0x7c/0x104
lr : fsg_main_thread+0x494/0x1b3c
Root cause is mass storage function try to queue request from main thread,
but other thread may already disable ep when function disable.
As there is no function failure in the driver, in order to avoid effort
to fix warning, change WARN_ON_ONCE() in usb_ep_queue() to pr_debug().
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240315020144.2715575-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Arrow Lake CPU uses the Meteor Lake ID with this
controller (the controller that's part of the Intel Arrow
Lake chipset (PCH) does still have unique PCI ID).
Fixes: de4b5b28c8 ("usb: dwc3: pci: add support for the Intel Arrow Lake-H")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240312115008.1748637-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device is configured for system wakeup, then make sure that the
xHCI driver knows about it and make sure to permit wakeup only at the
appropriate time.
For host mode, if the controller goes through the dwc3 code path, then a
child xHCI platform device is created. Make sure the platform device
also inherits the wakeup setting for xHCI to enable remote wakeup.
For device mode, make sure to disable system wakeup if no gadget driver
is bound. We may experience unwanted system wakeup due to the wakeup
signal from the controller PMU detecting connection/disconnection when
in low power (D3). E.g. In the case of Steam Deck, the PCI PME prevents
the system staying in suspend.
Cc: stable@vger.kernel.org
Reported-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Closes: https://lore.kernel.org/linux-usb/70a7692d-647c-9be7-00a6-06fc60f77294@igalia.com/T/#mf00d6669c2eff7b308d1162acd1d66c09f0853c7
Fixes: d07e8819a0 ("usb: dwc3: add xHCI Host support")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Sanath S <Sanath.S@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://lore.kernel.org/r/667cfda7009b502e08462c8fb3f65841d103cc0a.1709865476.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 75fd6485cc.
This patch was applied twice by accident, causing probe failures.
Revert the accident.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Fixes: 75fd6485cc ("usb: phy: generic: Get the vbus supply")
Cc: stable <stable@kernel.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240314092628.1869414-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wdm_read() cannot race with itself. However, in
service_outstanding_interrupt() it can race with the
workqueue, which can be triggered by error handling.
Hence we need to make sure that the WDM_RESPONDING
flag is not just only set but tested.
Fixes: afba937e54 ("USB: CDC WDM driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240314115132.3907-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Historically the expectation was to set brightness to max on enable, if
it was zero. However, the policy should be to preserve brightness across
disable/enable, for example the userspace might want to dim the
brightness before disable (e.g. on suspend) and gradually bring it back
up after enable (e.g. on resume). If the brightness gets bumped to max
at enable, this causes flicker as the userspace expects the brightness
to have been preserved across disable/enable.
For example:
(suspend)
[53949.248875] i915 0000:00:02.0: [drm:intel_edp_backlight_off]
[53949.452046] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level] set backlight PWM = 0
(wakeup)
[53986.067356] i915 0000:00:02.0: [drm:intel_edp_backlight_on]
[53986.067367] i915 0000:00:02.0: [drm:intel_backlight_enable] pipe A
[53986.067476] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level] set backlight PWM = 96000
[53986.119766] backlight intel_backlight: PM: calling backlight_resume+0x0/0x7a @ 4916, parent: card0-eDP-1
[53986.119781] backlight intel_backlight: PM: backlight_resume+0x0/0x7a returned 0 after 0 usecs
[53986.220068] [drm:intel_backlight_device_update_status] updating intel_backlight, brightness=26321/96000
[53986.220086] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight] set backlight level = 27961
Reduce the check to respecting the minimum brightness, and avoid bumping
min brightness to max on enable.
Note: It's possible there's still userspace out there that relies on the
old behaviour. It would be unfortunate, but there's really only one way
to find out.
Cc: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gareth Yu <gareth.yu@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[Jani: Rewrote the commit message.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240321045311.2124111-1-gareth.yu@intel.com
When we have no VBT we currently assume ports A-F are
all pontially valid for every platform. That is nonsense.
Grab the bitmask of valid ports from the runtime info
instead.
Although the defaults we actually fill here look semi-sensible
only for hsw-skl era hardware. Dunno if we should try to do
something more appropriate here for other platforms,
or just try to nuke the whole thing?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240319092443.15769-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The current version of delay reporting code can report incorrect
values when paired with a firmware which enables this feature.
Unfortunately there are several smaller issues that needed to be addressed
to correct the behavior:
Wrong information was used for the host side of counter
For MTL/LNL used incorrect (in a sense that it was verified only on MTL)
link side counter function.
The link side counter needs compensation logic if pause/resume is used.
The offset values were not refreshed from firmware.
Finally, not strictly connected, but the ALSA buffer size needs to be
constrained to avoid constant xrun from media players (like mpv)
The series applies cleanly for 6.9 and 6.8.y stable, but older stable
would need manual backport, but it is questionable if it is needed as
MTL/LNL is missing features.
Clock direction is marked as 'unsigned int' but only two values are
currently used in practice. Note these down in the documentation.
Signed-off-by: John Watts <contact@jookia.org>
Link: https://msgid.link/r/20240326-dai_mclk_hint-v1-1-653cbd2d78d9@jookia.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It has been reported the commit cf3986f8c0 introduced a regression
when the temperature is wavering in the hysteresis region. The
mitigation stops leading to an uncontrolled temperature increase until
reaching the critical trip point.
Here what happens:
* 'throttle' is when the current temperature is greater than the trip
point temperature
* 'target' is the mitigation level
* 'passive' is positive when there is a mitigation, zero otherwise
* these values are computed in the step_wise governor
Configuration:
trip point 1: temp=95°C, hyst=5°C (passive)
trip point 2: temp=115°C, hyst=0°C (critical)
governor: step_wise
1. The temperature crosses the way up the trip point 1 at 95°C
- trend=raising
- throttle=1, target=1
- passive=1
- set_trips: low=90°C, high=115°C
2. The temperature decreases but stays in the hysteresis region at
93°C
- trend=dropping
- throttle=0, target=0
- passive=1
Before cf3986f8c0
- set_trips: low=90°C, high=95°C
After cf3986f8c0
- set_trips: low=90°C, high=115°C
3. The temperature increases a bit but stays in the hysteresis region
at 94°C (so below the trip point 1 temp 95°C)
- trend=raising
- throttle=0, target=0
- passive=1
Before cf3986f8c0
- set_trips: low=90°C, high=95°C
After cf3986f8c0
- set_trips: low=90°C, high=115°C
4. The temperature decreases but stays in the hysteresis region at
93°C
- trend=dropping
- throttle=0, target=THERMAL_NO_TARGET
- passive=0
Before cf3986f8c0
- set_trips: low=90°C, high=95°C
After cf3986f8c0
- set_trips: low=90°C, high=115°C
At this point, the 'passive' value is zero, there is no mitigation,
the temperature is in the hysteresis region, the next trip point is
115°C. As 'passive' is zero, the timer to monitor the thermal zone is
disabled. Consequently if the temperature continues to increase, no
mitigation will happen and it will reach the 115°C trip point and
reboot.
Before the optimization, the high boundary would have been 95°C, thus
triggering the mitigation again and rearming the polling timer.
The optimization make sense but given the current implementation of
the step_wise governor collaborating via this 'passive' flag with the
core framework it can not work.
From a higher perspective it seems like there is a problem between the
governor which sets a variable to be used by the core framework. That
sounds akward and it would make much more sense if the core framework
controls the governor and not the opposite. But as the devil hides in
the details, there are some subtilities to be addressed before.
Elaborating those would be out of the scope this changelog. So let's
stay simple and revert the change first to fixup all broken mobile
platforms.
This reverts commit cf3986f8c0 ("thermal: core: Don't update trip
points inside the hysteresis range") and takes a conflict with commit
0c0c4740c9 ("0c0c4740c9 thermal: trip: Use for_each_trip() in
__thermal_zone_set_trips()") in drivers/thermal/thermal_trip.c into
account.
Fixes: cf3986f8c0 ("thermal: core: Don't update trip points inside the hysteresis range")
Reported-by: Manaf Meethalavalappu Pallikunhi <quic_manafm@quicinc.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Cc: 6.7+ <stable@vger.kernel.org> # 6.7+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Improve the error logging in the driver probe failure paths.
Also use dev_err_probe which is probe error check and log helper to
prevent logging in case of probe deferral.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240325204620.1437237-6-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
ACPICA commit 9061cd9aa131205657c811a52a9f8325a040c6c9
Errors in acpi_evaluate_object() can lead to incorrect state of buffer.
This can lead to access to data in previously ACPI_FREEd buffer and
secondary ACPI_FREE to the same buffer later.
Handle errors in acpi_evaluate_object the same way it is done earlier
with acpi_ns_handle_to_pathname.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: 9061cd9a
Fixes: 5fd033288a ("ACPICA: debugger: add command to dump all fields of particular subtype")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZgHmTAAKCRDbK58LschI
g1gWAP9HjAWE/Sy0B2t9opIiTqRzdMJLYs2B4OFeHRI6+qQg0gD6A4jsKEh/xmtG
Hhjw+AElJRFZ3SUIT4mZlljzUHIYYAA=
=T0lM
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-03-25
The following pull-request contains BPF updates for your *net* tree.
We've added 17 non-merge commits during the last 12 day(s) which contain
a total of 19 files changed, 184 insertions(+), 61 deletions(-).
The main changes are:
1) Fix an arm64 BPF JIT bug in BPF_LDX_MEMSX implementation's offset handling
found via test_bpf module, from Puranjay Mohan.
2) Various fixups to the BPF arena code in particular in the BPF verifier and
around BPF selftests to match latest corresponding LLVM implementation,
from Puranjay Mohan and Alexei Starovoitov.
3) Fix xsk to not assume that metadata is always requested in TX completion,
from Stanislav Fomichev.
4) Fix riscv BPF JIT's kfunc parameter incompatibility between BPF and the riscv
ABI which requires sign-extension on int/uint, from Pu Lehui.
5) Fix s390x BPF JIT's bpf_plt pointer arithmetic which triggered a crash when
testing struct_ops, from Ilya Leoshkevich.
6) Fix libbpf's arena mmap handling which had incorrect u64-to-pointer cast on
32-bit architectures, from Andrii Nakryiko.
7) Fix libbpf to define MFD_CLOEXEC when not available, from Arnaldo Carvalho de Melo.
8) Fix arm64 BPF JIT implementation for 32bit unconditional bswap which
resulted in an incorrect swap as indicated by test_bpf, from Artem Savkov.
9) Fix BPF man page build script to use silent mode, from Hangbin Liu.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
riscv, bpf: Fix kfunc parameters incompatibility between bpf and riscv abi
bpf: verifier: reject addr_space_cast insn without arena
selftests/bpf: verifier_arena: fix mmap address for arm64
bpf: verifier: fix addr_space_cast from as(1) to as(0)
libbpf: Define MFD_CLOEXEC if not available
arm64: bpf: fix 32bit unconditional bswap
bpf, arm64: fix bug in BPF_LDX_MEMSX
libbpf: fix u64-to-pointer cast on 32-bit arches
s390/bpf: Fix bpf_plt pointer arithmetic
xsk: Don't assume metadata is always requested in TX completion
selftests/bpf: Add arena test case for 4Gbyte corner case
selftests/bpf: Remove hard coded PAGE_SIZE macro.
libbpf, selftests/bpf: Adjust libbpf, bpftool, selftests to match LLVM
bpf: Clarify bpf_arena comments.
MAINTAINERS: Update email address for Quentin Monnet
scripts/bpf_doc: Use silent mode when exec make cmd
bpf: Temporarily disable atomic operations in BPF arena
====================
Link: https://lore.kernel.org/r/20240325213520.26688-1-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Merge series from Bo Liu <liubo03@inspur.com>:
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Bo Liu (13):
regulator: da9121: convert to use maple tree register cache
regulator: da9211: convert to use maple tree register cache
regulator: isl9305: convert to use maple tree register cache
regulator: max8973: convert to use maple tree register cache
regulator: mt6311: convert to use maple tree register cache
regulator: pca9450: convert to use maple tree register cache
regulator: pf8x00: convert to use maple tree register cache
regulator: pfuze100: convert to use maple tree register cache
regulator: rtmv20: convert to use maple tree register cache
regulator: rtq6752: convert to use maple tree register cache
regulator: tps51632: convert to use maple tree register cache
regulator: tps62360: convert to use maple tree register cache
regulator: rpi-panel-attiny: convert to use maple tree register cache
drivers/regulator/da9121-regulator.c | 4 ++--
drivers/regulator/da9211-regulator.c | 2 +-
drivers/regulator/isl9305.c | 2 +-
drivers/regulator/max8973-regulator.c | 2 +-
drivers/regulator/mt6311-regulator.c | 2 +-
drivers/regulator/pca9450-regulator.c | 2 +-
drivers/regulator/pf8x00-regulator.c | 2 +-
drivers/regulator/pfuze100-regulator.c | 2 +-
drivers/regulator/rpi-panel-attiny-regulator.c | 2 +-
drivers/regulator/rtmv20-regulator.c | 2 +-
drivers/regulator/rtq6752-regulator.c | 2 +-
drivers/regulator/tps51632-regulator.c | 2 +-
drivers/regulator/tps62360-regulator.c | 2 +-
13 files changed, 14 insertions(+), 14 deletions(-)
--
2.18.2
When consolidating GPIO lookups in ACPI code, the debug messaging
had been reworked that the user may see
[ 13.401147] (NULL device *): using ACPI '\_SB.LEDS.led-0' for '(null)' GPIO lookup
[ 13.401378] gpio gpiochip0: Persistence not supported for GPIO 40
[ 13.401402] gpio-40 (?): no flags found for (null)
instead of
[ 14.182962] gpio gpiochip0: Persistence not supported for GPIO 40
[ 14.182994] gpio-40 (?): no flags found for gpios
The '(null)' parts are less informative and likely scare the users.
Replace them by '(default)' which can point out to the default connection
IDs, such as 'gpios'.
While at it, amend other places where con_id is used in the messages.
Reported-by: Ferry Toth <ftoth@exalondelft.nl>
Fixes: 8eb1f71e7a ("gpiolib: consolidate GPIO lookups")
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
Fix kernel documentation and inclusion block, and dropping the size
of the num_chipselect.
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
A couple of cleanups against linux/spi/pxa2xx_spi.h.
I'm sending this as v3 to land in the SPI subsystem. Meanwhile I'm
preparing an update to make linux/spi/pxa2xx_spi.h private to the
subsystem (PXA2xx driver). But the second part will be presented later
on (likely after v6.9-rc1). That said, this can be routed either via
SoC tree or SPI, up to respective maintainers.
The gpio_device_find_by_() functions do not have stubs which means that if
they are referenced from code with an optiona dependency on gpiolib then
the code will fail to link. Add stubs for lookups via fwnode and label. I
have not added a stub for plain gpio_device_find() since it seems harder to
see a use case for that which does not depend on gpiolib.
With the addition of the GPIO reset controller (which lacks a gpiolib
dependency) to the arm64 defconfig this is causing build breaks for arm64
virtconfig in -next:
aarch64-linux-gnu-ld: drivers/reset/core.o: in function `__reset_add_reset_gpio_lookup':
/build/stage/linux/drivers/reset/core.c:861:(.text+0xccc): undefined reference to `gpio_device_find_by_fwnode'
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When an interrupt is requested, a procfs directory is created under
"/proc/irq/<irqnum>/<label>" where <label> is the string passed to one of
the request_irq() variants.
What follows is that the string must not contain the "/" character or
the procfs mkdir operation will fail. We don't have such constraints for
GPIO consumer labels which are used verbatim as interrupt labels for
GPIO irqs. We must therefore sanitize the consumer string before
requesting the interrupt.
Let's replace all "/" with ":".
Cc: stable@vger.kernel.org
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Closes: https://lore.kernel.org/linux-gpio/39fe95cb-aa83-4b8b-8cab-63947a726754@gmx.net/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Calling i915_gem_object_get_dma_address() from the vblank
evade critical section triggers might_sleep().
While we know that we've already pinned the framebuffer
and thus i915_gem_object_get_dma_address() will in fact
not sleep in this case, it seems reasonable to keep the
unconditional might_sleep() for maximum coverage.
So let's instead pre-populate the dma address during
fb pinning, which all happens before we enter the
vblank evade critical section.
We can use u32 for the dma address as this class of
hardware doesn't support >32bit addresses.
Cc: stable@vger.kernel.org
Fixes: 0225a90981 ("drm/i915: Make cursor plane registers unlocked")
Reported-by: Borislav Petkov <bp@alien8.de>
Closes: https://lore.kernel.org/intel-gfx/20240227100342.GAZd2zfmYcPS_SndtO@fat_crate.local/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240325175738.3440-1-ville.syrjala@linux.intel.com
Tested-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Systems with a large number of CPUs may generate a large number of
machine check records when things go seriously wrong. But Linux has
a fixed-size buffer that can only capture a few dozen errors.
Allocate space based on the number of CPUs (with a minimum value based
on the historical fixed buffer that could store 80 records).
[ bp: Rename local var from tmpp to something more telling: gpool. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Reviewed-by: Avadhut Naik <avadhut.naik@amd.com>
Link: https://lore.kernel.org/r/20240307192704.37213-1-tony.luck@intel.com
The current code is pulling the wrong pointer causing it to disable the
wrong IRQ. Correct the code to pull the correct cs42l43 core data
pointer.
Fixes: 64353af49f ("ASoC: cs42l43: Add system suspend ops to disable IRQ")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://msgid.link/r/20240326105434.852907-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unregistering SCMI notifications using the managed devres interface can be
done providing as a reference simply the previously successfully registered
notification block since it could have been registered only on one kernel
notification_chain: drop any reference to SCMI protocol, events and
sources.
Devres internal helpers can search for the provided notification block
reference and, once found, the associated devres object will already
provide the above SCMI references for the event.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240325204620.1437237-5-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
It is useful to have message dump traces for any invalid/bad/unexpected
replies. Let us add traces for the same as well as late-timed-out,
out-of-order and unexpected/spurious messages.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240325204620.1437237-4-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Locally generated IP multicast packets (such as the ones used in the
test) do not perform routing and simply egress the bound device.
However, as explained in commit 8bcfb4ae4d ("selftests: forwarding:
Fix failing tests with old libnet"), old versions of libnet (used by
mausezahn) do not use the "SO_BINDTODEVICE" socket option. Specifically,
the library started using the option for IPv6 sockets in version 1.1.6
and for IPv4 sockets in version 1.2. This explains why on Ubuntu - which
uses version 1.1.6 - the IPv4 overlay tests are failing whereas the IPv6
ones are passing.
Fix by specifying the source and destination MAC of the packets which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: 62199e3f16 ("selftests: net: Add VXLAN MDB test")
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/netdev/5bb50349-196d-4892-8ed2-f37543aa863f@alu.unizg.hr/
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20240325075030.2379513-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We have a couple of duplicate logs and missing information, add
__func__ consistently and make sure useful error codes are logged.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240325221925.206507-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpio field is not used anymore, remove the leftover.
This also fixes the compilation error after the ...
Fixes: 9855f05e55 ("ASoC: fsl: imx-es8328: Switch to using gpiod API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240325191341.3977321-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Upon reception of malformed and unexpected timed-out SCMI messages, it is
not possible to trace those bad messages in their entirety, because usually
we cannot even retrieve the payload, or it is just not reliable.
Add a helper to trace at least the content of the header of the received
message while associating a meaningful tag and error code.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240325204620.1437237-3-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The dreamcastcard->timer could schedule the spu_dma_work and the
spu_dma_work could also arm the dreamcastcard->timer.
When the snd_pcm_substream is closing, the aica_channel will be
deallocated. But it could still be dereferenced in the worker
thread. The reason is that del_timer() will return directly
regardless of whether the timer handler is running or not and
the worker could be rescheduled in the timer handler. As a result,
the UAF bug will happen. The racy situation is shown below:
(Thread 1) | (Thread 2)
snd_aicapcm_pcm_close() |
... | run_spu_dma() //worker
| mod_timer()
flush_work() |
del_timer() | aica_period_elapsed() //timer
kfree(dreamcastcard->channel) | schedule_work()
| run_spu_dma() //worker
... | dreamcastcard->channel-> //USE
In order to mitigate this bug and other possible corner cases,
call mod_timer() conditionally in run_spu_dma(), then implement
PCM sync_stop op to cancel both the timer and worker. The sync_stop
op will be called from PCM core appropriately when needed.
Fixes: 198de43d75 ("[ALSA] Add ALSA support for the SEGA Dreamcast PCM device")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Message-ID: <20240326094238.95442-1-duoming@zju.edu.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sebastian Andrzej Siewior says:
====================
net: Provide SMP threads for backlog NAPI
The RPS code and "deferred skb free" both send IPI/ function call
to a remote CPU in which a softirq is raised. This leads to a warning on
PREEMPT_RT because raising softiqrs from function call led to undesired
behaviour in the past. I had duct tape in RT for the "deferred skb free"
and Wander Lairson Costa reported the RPS case.
This series only provides support for SMP threads for backlog NAPI, I
did not attach a patch to make it default and remove the IPI related
code to avoid confusion. I can post it for reference it asked.
The RedHat performance team was so kind to provide some testing here.
The series (with the IPI code removed) has been tested and no regression
vs without the series has been found. For testing iperf3 was used on 25G
interface, provided by mlx5, ix40e or ice driver and RPS was enabled. I
can provide the individual test results if needed.
====================
Link: https://lore.kernel.org/r/20240325074943.289909-1-bigeasy@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The rps_lock.*() functions use the inner lock of a sk_buff_head for
locking. This lock is used if RPS is enabled, otherwise the list is
accessed lockless and disabling interrupts is enough for the
synchronisation because it is only accessed CPU local. Not only the list
is protected but also the NAPI state protected.
With the addition of backlog threads, the lock is also needed because of
the cross CPU access even without RPS. The clean up of the defer_list
list is also done via backlog threads (if enabled).
It has been suggested to rename the locking function since it is no
longer just RPS.
Rename the rps_lock*() functions to backlog_lock*().
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The defer_list is a per-CPU list which is used to free skbs outside of
the socket lock and on the CPU on which they have been allocated.
The list is processed during NAPI callbacks so ideally the list is
cleaned up.
Should the amount of skbs on the list exceed a certain water mark then
the softirq is triggered remotely on the target CPU by invoking a remote
function call. The raise of the softirqs via a remote function call
leads to waking the ksoftirqd on PREEMPT_RT which is undesired.
The backlog-NAPI threads already provide the infrastructure which can be
utilized to perform the cleanup of the defer_list.
The NAPI state is updated with the input_pkt_queue.lock acquired. It
order not to break the state, it is needed to also wake the backlog-NAPI
thread with the lock held. This requires to acquire the use the lock in
rps_lock_irq*() if the backlog-NAPI threads are used even with RPS
disabled.
Move the logic of remotely starting softirqs to clean up the defer_list
into kick_defer_list_purge(). Make sure a lock is held in
rps_lock_irq*() if backlog-NAPI threads are used. Schedule backlog-NAPI
for defer_list cleanup if backlog-NAPI is available.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Backlog NAPI is a per-CPU NAPI struct only (with no device behind it)
used by drivers which don't do NAPI them self, RPS and parts of the
stack which need to avoid recursive deadlocks while processing a packet.
The non-NAPI driver use the CPU local backlog NAPI. If RPS is enabled
then a flow for the skb is computed and based on the flow the skb can be
enqueued on a remote CPU. Scheduling/ raising the softirq (for backlog's
NAPI) on the remote CPU isn't trivial because the softirq is only
scheduled on the local CPU and performed after the hardirq is done.
In order to schedule a softirq on the remote CPU, an IPI is sent to the
remote CPU which schedules the backlog-NAPI on the then local CPU.
On PREEMPT_RT interrupts are force-threaded. The soft interrupts are
raised within the interrupt thread and processed after the interrupt
handler completed still within the context of the interrupt thread. The
softirq is handled in the context where it originated.
With force-threaded interrupts enabled, ksoftirqd is woken up if a
softirq is raised from hardirq context. This is the case if it is raised
from an IPI. Additionally there is a warning on PREEMPT_RT if the
softirq is raised from the idle thread.
This was done for two reasons:
- With threaded interrupts the processing should happen in thread
context (where it originated) and ksoftirqd is the only thread for
this context if raised from hardirq. Using the currently running task
instead would "punish" a random task.
- Once ksoftirqd is active it consumes all further softirqs until it
stops running. This changed recently and is no longer the case.
Instead of keeping the backlog NAPI in ksoftirqd (in force-threaded/
PREEMPT_RT setups) I am proposing NAPI-threads for backlog.
The "proper" setup with threaded-NAPI is not doable because the threads
are not pinned to an individual CPU and can be modified by the user.
Additionally a dummy network device would have to be assigned. Also
CPU-hotplug has to be considered if additional CPUs show up.
All this can be probably done/ solved but the smpboot-threads already
provide this infrastructure.
Sending UDP packets over loopback expects that the packet is processed
within the call. Delaying it by handing it over to the thread hurts
performance. It is not beneficial to the outcome if the context switch
happens immediately after enqueue or after a while to process a few
packets in a batch.
There is no need to always use the thread if the backlog NAPI is
requested on the local CPU. This restores the loopback throuput. The
performance drops mostly to the same value after enabling RPS on the
loopback comparing the IPI and the tread result.
Create NAPI-threads for backlog if request during boot. The thread runs
the inner loop from napi_threaded_poll(), the wait part is different. It
checks for NAPI_STATE_SCHED (the backlog NAPI can not be disabled).
The NAPI threads for backlog are optional, it has to be enabled via the boot
argument "thread_backlog_napi". It is mandatory for PREEMPT_RT to avoid the
wakeup of ksoftirqd from the IPI.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A NAPI thread is scheduled by first setting NAPI_STATE_SCHED bit. If
successful (the bit was not yet set) then the NAPI_STATE_SCHED_THREADED
is set but only if thread's state is not TASK_INTERRUPTIBLE (is
TASK_RUNNING) followed by task wakeup.
If the task is idle (TASK_INTERRUPTIBLE) then the
NAPI_STATE_SCHED_THREADED bit is not set. The thread is no relying on
the bit but always leaving the wait-loop after returning from schedule()
because there must have been a wakeup.
The smpboot-threads implementation for per-CPU threads requires an
explicit condition and does not support "if we get out of schedule()
then there must be something to do".
Removing this optimisation simplifies the following integration.
Set NAPI_STATE_SCHED_THREADED unconditionally on wakeup and rely on it
in the wait path by removing the `woken' condition.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use the `DEFINE_FLEX()` helper for an on-stack definition of a
flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warning:
sound/firewire/amdtp-stream.c:1184:46: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Link: https://github.com/KSPP/linux/issues/202
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Message-ID: <ZgIsBqoMb7p3fMDr@neat>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The remove callback of a device is called whenever it is unbound,
which may happen during runtime e.g. through sysfs, so this is not
allowed to be dropped from the binary:
WARNING: modpost: vmlinux: section mismatch in reference: einj_driver+0x8 (section: .data) -> einj_remove (section: .exit.text)
ERROR: modpost: Section mismatches detected.
Remove that annotation.
Fixes: 12fb28ea6b ("EINJ: Add CXL error type support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, the performance domain names are not logged whenever any
error occurs when processing the OPPs by adding to local data structures
or to the OPP library.
It would be easier to locate the problem if domain name is printed out.
So let us add the performance domain names to the other information
logged already in the error paths.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240322080531.3365016-1-peng.fan@oss.nxp.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
