Export fscache_put_volume() and add fscache_try_get_volume()
helper function to allow cachefiles to get/put fscache_volume
via linux/fscache-cache.h.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Link: https://lore.kernel.org/r/20240628062930.2467993-2-libaokun@huaweicloud.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Stock kernel scales worse than FreeBSD when doing a 20-way stat(2) on
the same tmpfs-backed file.
According to perf top:
38.09% lockref_put_return
26.08% lockref_get_not_dead
25.60% __d_lookup_rcu
0.89% clear_bhb_loop
__d_lookup_rcu is participating in cacheline ping pong due to the
embedded name sharing a cacheline with lockref.
Moving it out resolves the problem:
41.50% lockref_put_return
41.03% lockref_get_not_dead
1.54% clear_bhb_loop
benchmark (will-it-scale, Sapphire Rapids, tmpfs, ops/s):
FreeBSD:7219334
before: 5038006
after: 7842883 (+55%)
One minor remark: the 'after' result is unstable, fluctuating in the
range ~7.8 mln to ~9 mln during different runs.
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Link: https://lore.kernel.org/r/20240613001215.648829-3-mjguzik@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
As described by the microchip article "LAN937X - The required
configuration for the external MAC port to operate at RGMII-to-RGMII
1Gbps link speed." [1]:
"When VPHY is enabled, the auto-negotiation process following IEEE 802.3
standard will be triggered and will result in RGMII-to-RGMII signal
failure on the interface because VPHY will try to poll the PHY status
that is not available in the scenario of RGMII-to-RGMII connection
(normally the link partner is usually an external processor).
Note that when VPHY fails on accessing PHY registers, it will fall back
to 100Mbps speed, it indicates disabling VPHY is optional if you only
need the port to link at 100Mbps speed.
Again, VPHY must and can only be disabled by writing VPHY_DISABLE bit in
the register below as there is no strapping pin for the control."
This patch was tested on LAN9372, so far it seems to not to affect VPHY
based clock crossing optimization for the ports with integrated PHYs.
[1]: https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver do not support in-band mode and in case of CPU<->Switch
link, this mode is not working any way. So, disable it otherwise ingress
path of the switch MAC will stay disabled.
Note: lan9372 manual do not document 0xN301 BIT(2) for the RGMII mode
and recommend[1] to disable in-band link status update for the RGMII RX
path by clearing 0xN302 BIT(0). But, 0xN301 BIT(2) seems to work too, so
keep it unified with other KSZ switches.
[1] https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the LAN9371 and LAN9372, the 4th internal PHY is a 100BaseTX PHY
instead of a 100BaseT1 PHY. The 100BaseTX PHYs have a different base
register offset.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 750011e239 ("net: stmmac: Add support for HW-accelerated VLAN
stripping") enables MAC level VLAN tag stripping for all MAC cores, but
leaves set_hw_vlan_mode() and rx_hw_vlan() un-implemented for both gmac
and xgmac.
On gmac and xgmac, ethtool reports rx-vlan-offload is on, both MAC and
driver do nothing about VLAN packets actually, although VLAN works well.
Driver level stripping should be used on gmac and xgmac for now.
Fixes: 750011e239 ("net: stmmac: Add support for HW-accelerated VLAN stripping")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The if condition !A || A && B can be simplified to !A || B.
Fixes the following Coccinelle/coccicheck warning reported by
excluded_middle.cocci:
WARNING !A || A && B is equivalent to !A || B
Compile-tested only.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240701195607.228852-1-thorsten.blum@toblux.com
Starting with kernel 6.7, the framebuffer text console is not working
anymore with the virtio-gpu device on s390x hosts. Such big endian fb
devices are usinga different pixel ordering than little endian devices,
e.g. DRM_FORMAT_BGRX8888 instead of DRM_FORMAT_XRGB8888.
This used to work fine as long as drm_client_buffer_addfb() was still
calling drm_mode_addfb() which called drm_driver_legacy_fb_format()
internally to get the right format. But drm_client_buffer_addfb() has
recently been reworked to call drm_mode_addfb2() instead with the
format value that has been passed to it as a parameter (see commit
6ae2ff23aa ("drm/client: Convert drm_client_buffer_addfb() to drm_mode_addfb2()").
That format parameter is determined in drm_fbdev_generic_helper_fb_probe()
via the drm_mode_legacy_fb_format() function - which only generates
formats suitable for little endian devices. So to fix this issue
switch to drm_driver_legacy_fb_format() here instead to take the
device endianness into consideration.
Fixes: 6ae2ff23aa ("drm/client: Convert drm_client_buffer_addfb() to drm_mode_addfb2()")
Closes: https://issues.redhat.com/browse/RHEL-45158
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627173530.460615-1-thuth@redhat.com
A sync-only job is meant to provide a synchronization point on a
queue, so we can't return a NULL fence there, we have to add a signal
operation to the command stream which executes after all other
previously submitted jobs are done.
v2:
- Fixed a UAF bug
- Added R-bs
Fixes: de85488138 ("drm/panthor: Add the scheduler logical block")
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240703071640.231278-3-boris.brezillon@collabora.com
The user is likely to leave all the drm_panthor_obj_array fields
to zero when the array is empty, which will cause an EINVAL failure.
v2:
- Added R-bs
Fixes: 4bdca11507 ("drm/panthor: Add the driver frontend block")
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240703071640.231278-2-boris.brezillon@collabora.com
Ast has no special requirements for runtime power management. So
replace drm_atomic_helper_commit_tail_rpm() with the regular helper
drm_atomic_helper_commit_tail().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-9-tzimmermann@suse.de
The function ast_crtc_dpms() is left over from when the ast driver
did not implement atomic modesetting. But DPMS is not supported by
atomic modesetting and the helper is only called to enable or
disable the CRTC sync pulses. Inline the function into its callers.
To disable the CRTC, ast sets (AST_DPMS_VSYNC_OFF | AST_DPMS_HSYNC_OFF)
in VGACRB6. Replace the constants with the correct register constants
for VGACRB6.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-8-tzimmermann@suse.de
The SCREEN_DISABLE bit controls scanout from display memory. The bit
affects all planes, so set it only in the CRTC's atomic enable and
disable functions.
A number of bugs affect this fix. First of all, ast_set_std_regs()
tries to set VGASR1 except for the SD bit. But the read bitmask is
invert, so it preserves anything except the SD bit. Fix this by
re-inverting the read mask.
The second issue is that primary-plane and CRTC helpers modify the
SD bit. The bit controls scanout for all planes, primary and HW
cursor, so set it only in the CRTC code.
Further add a constant to represent the SD bit in VGASR1. Keep the
plane's atomic_disable around to make the DRM framework happy.
v2:
- fix typos in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-7-tzimmermann@suse.de
The DPMS code, called from the CRTC's atomic_enable, rewrites the
gamma LUT. This is already done by the CRTC's atomic_flush. Remove
the duplication.
v2:
- fix a typo in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-6-tzimmermann@suse.de
Several color registers are programmed in the DPMS code of the CRTC's
atomic_enable helper and the primary plane's atomic_update. It requires
the color format and the display mode.
Both code paths handle different cases: the DPMS's code will not be
executed if the color format changes without a full mode switch. The
plane's code only runs if the color format changes, but ignores
display-mode changes.
The color format is a property of the primary plane, so consolidate all
color-format code in the plane's atomic_update. Remove it from the DPMS
helper.
v2:
- clarify commit message (Jocelyn)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-5-tzimmermann@suse.de
Do all mode setting in ast_crtc_helper_mode_set_nofb(), which
always runs after disabling the CRTC and before programming the
planes. Removes implicit synchronization between the CRTC's
atomic disable, enable and the vertical retrace.
Display-mode updates require HW cursors to be disabled. The HW
cursor only picks up changes at vertical retrace periods. So the
CRTC's atomic_disable helper waited for the retrace to delay any
following mode-setting operations, which then happened in
atomic_enable. See [1] for a description of the problem.
With the CRTC helper callback mode_set_nofb, we can now synchronize
and reprogram in the same place. As it always runs before the plane
update, the plane code can be reordered with the CRTC's later
atomic_enable et al.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/series/79914/ # 1
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-4-tzimmermann@suse.de
The CRTC's atomic_flush function contains code to program the
display mode to the AST DP chip. Move the code to the encoder's
atomic_mode_set callback. The DRM atomic-modesetting code invoke
this callback as part of the atomic commit.
v2:
- fix typos in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-3-tzimmermann@suse.de
The CRTC helpers contain code to enable and disable DisplayPort
connectors. Implement this functionality in the respective connector's
atomic_enable/atomic_disable callbacks. DRM's atomic-modesetting
helpers will call the functions as part of the atomic commit.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-2-tzimmermann@suse.de
The encoding of an x86 instruction can include a ModR/M and a SIB
(Scale-Index-Base) byte to describe the addressing mode of the
instruction.
objtool processes all addressing mode with a SIB base of 5 as having
%rbp as the base register. However, a SIB base of 5 means that the
effective address has either no base (if ModR/M mod is zero) or %rbp
as the base (if ModR/M mod is 1 or 2). This can cause objtool to confuse
an absolute address access with a stack operation.
For example, objtool will see the following instruction:
4c 8b 24 25 e0 ff ff mov 0xffffffffffffffe0,%r12
as a stack operation (i.e. similar to: mov -0x20(%rbp), %r12).
[Note that this kind of weird absolute address access is added by the
compiler when using KASAN.]
If this perceived stack operation happens to reference the location
where %r12 was pushed on the stack then the objtool validation will
think that %r12 is being restored and this can cause a stack state
mismatch.
This kind behavior was seen on xfs code, after a minor change (convert
kmem_alloc() to kmalloc()):
>> fs/xfs/xfs.o: warning: objtool: xfs_da_grow_inode_int+0x6c1: stack state mismatch: reg1[12]=-2-48 reg2[12]=-1+0
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402220435.MGN0EV6l-lkp@intel.com/
Signed-off-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Link: https://lore.kernel.org/r/20240620144747.2524805-1-alexandre.chartre@oracle.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The help message mentions the main options as "actions", which is
different from the optional "options". But the check error messages
outputs "option" or "command" for referring to actions.
Make the error messages consistent with help.
Signed-off-by: Siddh Raman Pant <siddh.raman.pant@oracle.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Rather than looping through each symbol in a particular section to
calculate a symbol's size, grep for the symbol and its immediate
successor, and only use those two symbols.
Signed-off-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Link: https://lore.kernel.org/r/20240415145538.1938745-8-bjohannesmeyer@gmail.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Rather than invoking a separate addr2line process for each address, invoke
a single addr2line coprocess, and pass each address to its stdin. Previous
work [0] applied a similar change to perf, leading to a ~60x speed-up [1].
If using an object file that is _not_ vmlinux, faddr2line passes a section
name argument to addr2line. Because we do not know until runtime which
section names will be passed to addr2line, we cannot apply this change to
non-vmlinux object files. Hence, it only applies to vmlinux.
[0] commit be8ecc57f1 ("perf srcline: Use long-running addr2line per
DSO")
[1] Link:
https://eighty-twenty.org/2021/09/09/perf-addr2line-speed-improvement
Signed-off-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Link: https://lore.kernel.org/r/20240415145538.1938745-6-bjohannesmeyer@gmail.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
In preparation for identifying an addr2line sentinel. See previous work
[0], which applies a similar change to perf.
[0] commit 8dc26b6f71 ("perf srcline: Make sentinel reading for binutils
addr2line more robust")
Signed-off-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Link: https://lore.kernel.org/r/20240415145538.1938745-5-bjohannesmeyer@gmail.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Rather than checking whether the object file is vmlinux for each invocation
of __faddr2line, check it only once beforehand.
Signed-off-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Link: https://lore.kernel.org/r/20240415145538.1938745-4-bjohannesmeyer@gmail.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Rather than calling readelf three separate times to collect three different
types of info, call it only once, and parse out the different types of info
from its output.
Signed-off-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Link: https://lore.kernel.org/r/20240415145538.1938745-3-bjohannesmeyer@gmail.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Rather than calling readelf several times for each invocation of
__faddr2line, call readelf only three times at the beginning, and save its
result for future use.
Signed-off-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Link: https://lore.kernel.org/r/20240415145538.1938745-2-bjohannesmeyer@gmail.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Clang warns (or errors with CONFIG_WERROR=y):
drivers/power/supply/cros_charge-control.c:319:2: error: array index 3 is past the end of the array (that has type 'struct attribute *[3]') [-Werror,-Warray-bounds]
319 | priv->attributes[_CROS_CHCTL_ATTR_COUNT] = NULL;
| ^ ~~~~~~~~~~~~~~~~~~~~~~
drivers/power/supply/cros_charge-control.c:49:2: note: array 'attributes' declared here
49 | struct attribute *attributes[_CROS_CHCTL_ATTR_COUNT];
| ^
1 error generated.
In earlier revisions of the driver, the attributes array in
cros_chctl_priv had four elements with four distinct assignments but
during review, the number of elements was changed to three through use
of an enum and the assignments became a for loop, except for this one,
which is now out of bounds. This assignment is no longer necessary
because the size of the attributes array no longer accounts for it, so
just remove it to clear up the warning.
Fixes: c6ed48ef52 ("power: supply: add ChromeOS EC based charge control driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20240702-cros_charge-control-fix-clang-array-bounds-warning-v1-1-ae04d995cd1d@kernel.org
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Prefer the struct drm_edid based functions for storing the EDID and
updating the connector.
It would be better if the vidi connection ioctl passed in the EDID size
separately instead of relying on the extension count specified in the
EDID, but that's what we have to rely on.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Avoid assigning fake_edid_info to ctx->raw_edid. Always keep
ctx->raw_edid either an allocated pointer or NULL. Defer fake_edid_info
handling to .get_modes().
This should be functionally equivalent but slightly easier to follow.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Don't open code drm_edid_duplicate(). While at it, drop the error
message on allocation failure.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Samsung Galaxy Grand 2 is a phone based on MSM8226. It's similar to the
other Samsung devices based on MSM8226 with only a few minor differences.
The device trees contain initial support with:
- GPIO keys
- Regulator haptic
- SDHCI (internal and external storage)
- UART (on USB connector via the TI TSU6721 MUIC)
- Regulators
- Touchscreen
- Accelerometer
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Reviewed-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240630132859.2885-3-raymondhackley@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
ASUS Vivobook S 15 is a laptop based on the Qualcomm Snapdragon X Elite
SoC (X1E78100).
Add the device tree for the laptop with support for the following features:
- CPU frequency scaling up to 3.4GHz
- NVMe storage on PCIe 6a (capable of Gen4x4, currently limited to Gen4x2)
- Keyboard and touchpad
- WCN7850 Wi-Fi
- Two Type-C ports on the left side (USB3 only in one orientation)
- internal eDP display
- ADSP and CDSP remoteprocs
Further details could be found in the cover letter.
Signed-off-by: Xilin Wu <wuxilin123@gmail.com>
Link: https://lore.kernel.org/r/20240701-asus-vivobook-s15-v4-2-ce7933b4d4e5@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
According to downstream sources, maximum current for PMI632 VBUS
is 1A.
Taken from msm-4.19 (631561973a034e46ccacd0e53ef65d13a40d87a4)
Line 685-687 in drivers/power/supply/qcom/qpnp-smb5.c
Fixes: a06a2f12f9 ("arm64: dts: qcom: qrb4210-rb2: enable USB-C port handling")
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240702-qrd4210rb2-vbus-volt-v3-1-fbd24661eec4@riseup.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
cifs_expand_read() is causing a performance regression of around 30% by
causing extra pagecache to be allocated for an inode in the readahead path
before we begin actually dispatching RPC requests, thereby delaying the
actual I/O. The expansion is sized according to the rsize parameter, which
seems to be 4MiB on my test system; this is a big step up from the first
requests made by the fio test program.
Simple repro (look at read bandwidth number):
fio --name=writetest --filename=/xfstest.test/foo --time_based --runtime=60 --size=16M --numjobs=1 --rw=read
Fix this by removing cifs_expand_readahead(). Readahead expansion is
mostly useful for when we're using the local cache if the local cache has a
block size greater than PAGE_SIZE, so we can dispense with it when not
caching.
Fixes: 69c3c023af ("cifs: Implement netfslib hooks")
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
cc: linux-mm@kvack.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Support building the C YNL userspace library into one big static file.
We can then link selftests against it for easy to use C netlink
interface.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20240628003253.1694510-14-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Abstract the memory type from the page_pool so we can later add support
for new memory types. Convert the page_pool to use the new netmem type
abstraction, rather than use struct page directly.
As of this patch the netmem type is a no-op abstraction: it's always a
struct page underneath. All the page pool internals are converted to
use struct netmem instead of struct page, and the page pool now exports
2 APIs:
1. The existing struct page API.
2. The new struct netmem API.
Keeping the existing API is transitional; we do not want to refactor all
the current drivers using the page pool at once.
The netmem abstraction is currently a no-op. The page_pool uses
page_to_netmem() to convert allocated pages to netmem, and uses
netmem_to_page() to convert the netmem back to pages to pass to mm APIs,
Follow up patches to this series add non-paged netmem support to the
page_pool. This change is factored out on its own to limit the code
churn to this 1 patch, for ease of code review.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://patch.msgid.link/20240628003253.1694510-6-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following is emitted when using idxd (DSA) dmanegine as the data
mover for ntb_transport that ntb_netdev uses.
[74412.546922] BUG: using smp_processor_id() in preemptible [00000000] code: irq/52-idxd-por/14526
[74412.556784] caller is netif_rx_internal+0x42/0x130
[74412.562282] CPU: 6 PID: 14526 Comm: irq/52-idxd-por Not tainted 6.9.5 #5
[74412.569870] Hardware name: Intel Corporation ArcherCity/ArcherCity, BIOS EGSDCRB1.E9I.1752.P05.2402080856 02/08/2024
[74412.581699] Call Trace:
[74412.584514] <TASK>
[74412.586933] dump_stack_lvl+0x55/0x70
[74412.591129] check_preemption_disabled+0xc8/0xf0
[74412.596374] netif_rx_internal+0x42/0x130
[74412.600957] __netif_rx+0x20/0xd0
[74412.604743] ntb_netdev_rx_handler+0x66/0x150 [ntb_netdev]
[74412.610985] ntb_complete_rxc+0xed/0x140 [ntb_transport]
[74412.617010] ntb_rx_copy_callback+0x53/0x80 [ntb_transport]
[74412.623332] idxd_dma_complete_txd+0xe3/0x160 [idxd]
[74412.628963] idxd_wq_thread+0x1a6/0x2b0 [idxd]
[74412.634046] irq_thread_fn+0x21/0x60
[74412.638134] ? irq_thread+0xa8/0x290
[74412.642218] irq_thread+0x1a0/0x290
[74412.646212] ? __pfx_irq_thread_fn+0x10/0x10
[74412.651071] ? __pfx_irq_thread_dtor+0x10/0x10
[74412.656117] ? __pfx_irq_thread+0x10/0x10
[74412.660686] kthread+0x100/0x130
[74412.664384] ? __pfx_kthread+0x10/0x10
[74412.668639] ret_from_fork+0x31/0x50
[74412.672716] ? __pfx_kthread+0x10/0x10
[74412.676978] ret_from_fork_asm+0x1a/0x30
[74412.681457] </TASK>
The cause is due to the idxd driver interrupt completion handler uses
threaded interrupt and the threaded handler is not hard or soft interrupt
context. However __netif_rx() can only be called from interrupt context.
Change the call to netif_rx() in order to allow completion via normal
context for dmaengine drivers that utilize threaded irq handling.
While the following commit changed from netif_rx() to __netif_rx(),
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context."),
the change should've been a noop instead. However, the code precedes this
fix should've been using netif_rx_ni() or netif_rx_any_context().
Fixes: 548c237c0a ("net: Add support for NTB virtual ethernet device")
Reported-by: Jerry Dai <jerry.dai@intel.com>
Tested-by: Jerry Dai <jerry.dai@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://patch.msgid.link/20240701181538.3799546-1-dave.jiang@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The header is missing the include guards so add them.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Fixes: fb470f70fe ("net: phy: aquantia: add hwmon support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20240701080322.9569-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With ARCH=arm64, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/clk/versatile/clk-vexpress-osc.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240613-md-arm64-drivers-clk-versatile-v1-1-6b8a5e5e00ef@quicinc.com
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently clk-gate tests for s390 fail as the tests create a pretend
clk-gate and use a "fake_reg" to emulate the expected behavior of the
clk_gate->reg. I added some debug statements to the driver and noticed
that the reg changes after initialization to -1, which is coming from an
error coming from zpci_load(). This is likely because the test is using
fake iomem and the s390 architecture likely isn't designed to handle
that. Turn off the clk-gate tests for s390 for now as there is no clear
work around for this problem as discussed in upstream conversation [1].
[1] https://lore.kernel.org/all/301cd41e6283c12ac67fb8c0f8d5c929.sboyd@kernel.org/T/#t
Signed-off-by: Audra Mitchell <audra@redhat.com>
Link: https://lore.kernel.org/r/20240702125539.524489-1-audra@redhat.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Replace the open-coded parsing of "reg" with of_property_read_reg().
The #ifdef is also easily replaced with IS_ENABLED().
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240702215402.839673-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the open-coded parsing of "reg" with of_property_read_reg().
The #ifdef is also easily replaced with IS_ENABLED().
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240702215349.839350-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
