In order to rename the "header" file to "data" without conflicting,
correctly identify the non-header files as starting with "data."
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lore.kernel.org/lkml/20191004083121.12182-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Until now the size of a Rx buffer was artificially limited
to 1536B (which happens to be the default, after reset, hardware
value for a Rx buffer). This approach however leaves unused
memory space for Rx packets, since the driver uses a paged
allocation scheme that reserves half a page for each Rx skb.
There's also the inconvenience that frames around 1536 bytes
can get scattered if the limit is slightly exceeded. This limit
can be exceeded even for standard MTU of 1500B traffic, for common
cases like stacked VLANs, or DSA tags.
To address these issues, let's just compute the buffer size
starting from the upper limit of 2KB (half a page) and
subtract the skb overhead and alignment restrictions.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function page_shift() is supported after the commit 94ad933810
("mm: introduce page_shift()").
So replace with page_shift() in ehea_is_hugepage() for readability.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for xmit_more based on the igb commit 6f19e12f62
("igb: flush when in xmit_more mode and under descriptor pressure") and
commit 6b16f9ee89 ("net: move skb->xmit_more hint to softnet data") that
were made to igb to support this feature. The function netif_xmit_stopped
is called to check whether transmit queue on device is currently unable to
send to determine whether we must write the tail because we can add no
further buffers.
When normal packets and/or xmit_more packets fill up tx_desc, it is
necessary to trigger NIC tx reg.
Following the advice from David Miller and Jakub Kicinski, after the
xmit_more feature is added, the following scenario will occur.
|
xmit_more packets
|
DMA_MAPPING
|
DMA_MAPPING error check
|
xmit_more packets already in HW xmit queue
|
In the above scenario, if DMA_MAPPING error occurrs, the xmit_more packets
already in HW xmit queue will also be dropped. This is different from the
behavior before xmit_more feature. So it is necessary to trigger NIC HW tx
reg in the above scenario.
To the non-xmit_more packets, the above scenario will not occur.
Tested:
- pktgen (xmit_more packets) SMP x86_64 ->
Test command:
./pktgen_sample03_burst_single_flow.sh ... -b 8 -n 1000000
Test results:
Params:
...
burst: 8
...
Result: OK: 12194004(c12188996+d5007) usec, 1000001 (1500byte,0frags)
82007pps 984Mb/sec (984084000bps) errors: 0
- iperf (normal packets) SMP x86_64 ->
Test command:
Server: iperf -s
Client: iperf -c serverip
Result:
TCP window size: 85.0 KByte (default)
------------------------------------------------------------
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 1.10 GBytes 942 Mbits/sec
CC: Joe Jin <joe.jin@oracle.com>
CC: JUNXIAO_BI <junxiao.bi@oracle.com>
Reported-and-tested-by: Nan san <nan.1986san@gmail.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a call to io_submit_sqe(), it's already known whether it needs
to queue a link or not. Do it there, as it's simplier and doesn't keep
an extra variable across the loop.
Reviewed-by：Bob Liu <bob.liu@oracle.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_submit_sqes() and io_ring_submit() are doing the same stuff with
a little difference. Deduplicate them.
Reviewed-by：Bob Liu <bob.liu@oracle.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When using the example SOF amp widget topology, KASAN dumps this
when the AMP bytes kcontrol gets loaded:
[ 9.579548] BUG: KASAN: slab-out-of-bounds in
sof_control_load+0x8cc/0xac0 [snd_sof]
[ 9.588194] Write of size 40 at addr ffff8882314559dc by task
systemd-udevd/2411
Fix that by rejecting the topology if the bytes data size > max_size
Fixes: 311ce4fe76 ("ASoC: SOF: Add support for loading topologies")
Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191106145816.9367-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
perf report/top:
Jiri Olsa:
- Fix time sorting for big numbers, i.e.:
perf report -s time -F time,overhead --stdio
was failing because the sort comparision routine was returning 'int' while
that particular -s key was int64_t, fix it.
perf scripting engines:
Steven Rostedt (VMware):
- Iterate on tep event arrays directly, fixing a bug when generating python/perl
source code from a perf.data file with more than one tracepoint event.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXcGdpgAKCRCyPKLppCJ+
JwoXAQDeac29fMxv3fHcmkxjQnt5M0f3GV14+bT8qmUZhDgi0QD8DzVpa1iKF+cC
N26yDNU0zcj6Rs6WUWlBgyXfvrS4JQs=
=fbXe
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-5.4-20191105' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf fixes from Arnaldo Carvalho de Melo:
perf report/top:
Jiri Olsa:
- Fix time sorting for big numbers, i.e.:
perf report -s time -F time,overhead --stdio
was failing because the sort comparision routine was returning 'int' while
that particular -s key was int64_t, fix it.
perf scripting engines:
Steven Rostedt (VMware):
- Iterate on tep event arrays directly, fixing a bug when generating python/perl
source code from a perf.data file with more than one tracepoint event.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
drm_self_refresh_helper_update_avg_times() was incorrectly accessing the
new incoming state after drm_atomic_helper_commit_hw_done(). But this
state might have already been superceeded by an !nonblock atomic update
resulting in dereferencing an already free'd crtc_state.
TODO I *think* this will more or less do the right thing.. althought I'm
not 100% sure if, for example, we enter psr in a nonblock commit, and
then leave psr in a !nonblock commit that overtakes the completion of
the nonblock commit. Not sure if this sort of scenario can happen in
practice. But not crashing is better than crashing, so I guess we
should either take this patch or rever the self-refresh helpers until
Sean can figure out a better solution.
Fixes: d4da4e3334 ("drm: Measure Self Refresh Entry/Exit times to avoid thrashing")
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
[seanpaul fixed up some checkpatch warns]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104173737.142558-1-robdclark@gmail.com
Jakub Kicinski says:
====================
netdevsim: fix tests and netdevsim
The first patch fixes a merge which brought back some dead
code. Next a tiny re-write of the main test using netdevsim
aims to ease debugging.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to netdevsim moved creating and destroying
devices from netlink to sysfs. The sysfs writes have been
implemented as direct writes, without shelling out. This
is faster, but leaves no trace in the logs. Add explicit
logs to make debugging possible.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the port adding loop makes a re-appearance on net-next
after net was merged back into it (even though it doesn't feature
in the merge diff).
The ports are already added in nsim_dev_create() so when we try
to add them again get EEXIST, and see:
netdevsim: probe of netdevsim0 failed with error -17
in the logs. When we remove the loop again the nsim_dev_probe()
and nsim_dev_remove() become a wrapper of nsim_dev_create() and
nsim_dev_destroy(). Remove this layer of indirection.
Fixes: d31e95585c ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver could access a NULL firmware pointer if we don't
return here.
Fixes: 5195b90426 ("rtw88: avoid FW info flood")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This leak was found by testing the EDIMAX EW-7612 on Raspberry Pi 3B+ with
Linux 5.4-rc5 (multi_v7_defconfig + rtlwifi + kmemleak) and noticed a
single memory leak during probe:
unreferenced object 0xec13ee40 (size 176):
comm "kworker/u8:1", pid 36, jiffies 4294939321 (age 5580.790s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fc1bbb3e>] __netdev_alloc_skb+0x9c/0x164
[<863dfa6e>] rtl92c_set_fw_rsvdpagepkt+0x254/0x340 [rtl8192c_common]
[<9572be0d>] rtl92cu_set_hw_reg+0xf48/0xfa4 [rtl8192cu]
[<116df4d8>] rtl_op_bss_info_changed+0x234/0x96c [rtlwifi]
[<8933575f>] ieee80211_bss_info_change_notify+0xb8/0x264 [mac80211]
[<d4061e86>] ieee80211_assoc_success+0x934/0x1798 [mac80211]
[<e55adb56>] ieee80211_rx_mgmt_assoc_resp+0x174/0x314 [mac80211]
[<5974629e>] ieee80211_sta_rx_queued_mgmt+0x3f4/0x7f0 [mac80211]
[<d91091c6>] ieee80211_iface_work+0x208/0x318 [mac80211]
[<ac5fcae4>] process_one_work+0x22c/0x564
[<f5e6d3b6>] worker_thread+0x44/0x5d8
[<82c7b073>] kthread+0x150/0x154
[<b43e1b7d>] ret_from_fork+0x14/0x2c
[<794dff30>] 0x0
It is because 8192cu doesn't implement usb_cmd_send_packet(), and this
patch just frees the skb within the function to resolve memleak problem
by now. Since 8192cu doesn't turn on fwctrl_lps that needs to download
command packet for firmware via the function, applying this patch doesn't
affect driver behavior.
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> 41977e86 (diff-dae5dc10da)
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279: } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280: rt2x00_rt(rt2x00dev, RT5392) ||
> 5281: rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291: } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...
Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.
As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Reported-by: wbob <wbob@jify.de>
Reported-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:83:17: warning: 'rtl8225sez2_tx_power_cck' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:79:17: warning: 'rtl8225sez2_tx_power_cck_A' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:75:17: warning: 'rtl8225sez2_tx_power_cck_B' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:71:17: warning: 'rtl8225sez2_tx_power_cck_ch14' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:62:17: warning: 'rtl8225se_tx_power_ofdm' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:53:17: warning: 'rtl8225se_tx_power_cck_ch14' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:44:17: warning: 'rtl8225se_tx_power_cck' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:40:17: warning: 'rtl8225se_tx_gain_cck_ofdm' defined but not used [-Wunused-const-variable=]
They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:841:7: warning: variable free_pdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:30: warning: variable tx_rts_count set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:6: warning: variable tx_rts set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:843:7: warning: variable totlen set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LPS threshold was set to 2, means driver will leave LPS
mode if there is more than 2 frames TX/RX for every 2 seconds.
This makes driver enter/leave LPS frequently even if we just
"ping -i1" to the others.
Apparently we do not want to leave LPS mode if there is only
some background traffics or web surfing. By experiment, set
this to 50 is a more reasonable value to lower the over all
power consumption.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
local variable "ret" is not used. hence it is safe to remove and
just return 0.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
local variable "rc" is not used. It is safe to remove and
There is only one caller of libipw_qos_convert_ac_to_parameters().
hence make it void
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the cx debugbus related register configuration, to collect accurate
bus data during gpu snapshot. This helps with complete snapshot dump
and also complete proper GPU recovery.
Fixes: 1707add815 ("drm/msm/a6xx: Add a6xx gpu state")
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/339165
srq_desc_size should be rounded up to pow of two before used, or related
calculation may cause allocating wrong size of memory for srq buffer.
Fixes: c7bcb13442 ("RDMA/hns: Add SRQ support for hip08 kernel mode")
Link: https://lore.kernel.org/r/1572575610-52530-3-git-send-email-liweihang@hisilicon.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Size of pointer to buf field of struct hns_roce_hem_chunk should be
considered when calculating HNS_ROCE_HEM_CHUNK_LEN, or sg table size will
be larger than expected when allocating hem.
Fixes: 9a4435375c ("IB/hns: Add driver files for hns RoCE driver")
Link: https://lore.kernel.org/r/1572575610-52530-2-git-send-email-liweihang@hisilicon.com
Signed-off-by: Sirong Wang <wangsirong@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There is no need to return always zero for function which is not
supported.
Fixes: ac1b36e55a ("qedr: Add support for user context verbs")
Link: https://lore.kernel.org/r/20191028155931.1114-5-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There is no need to return always zero for function which is not
supported.
Fixes: fe2caefcdf ("RDMA/ocrdma: Add driver for Emulex OneConnect IBoE RDMA adapter")
Link: https://lore.kernel.org/r/20191028155931.1114-4-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There is no need to return always zero for function which is not
supported.
Fixes: 9a4435375c ("IB/hns: Add driver files for hns RoCE driver")
Link: https://lore.kernel.org/r/20191028155931.1114-3-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Improve return code from ib_modify_port() by doing the following:
- Use "-EOPNOTSUPP" instead "-ENOSYS" which is the proper return code
- Allow only fake IB_PORT_CM_SUP manipulation for RoCE providers that
didn't implement the modify_port callback, otherwise return
"-EOPNOTSUPP"
Fixes: 61e0962d52 ("IB: Avoid ib_modify_port() failure for RoCE devices")
Link: https://lore.kernel.org/r/20191028155931.1114-2-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Normal RDMA WRITE request never returns IB_WC_RNR_RETRY_EXC_ERR to ULPs
because it does not need post receive buffer on the responder side.
Consequently, as an enhancement to normal RDMA WRITE request inside the
hfi1 driver, TID RDMA WRITE request should not return such an error status
to ULPs, although it does receive RNR NAKs from the responder when TID
resources are not available. This behavior is violated when
qp->s_rnr_retry_cnt is set in current hfi1 implementation.
This patch enforces these semantics by avoiding any reaction to the updates
of the RNR QP attributes.
Fixes: 3c6cb20a0d ("IB/hfi1: Add TID RDMA WRITE functionality into RDMA verbs")
Link: https://lore.kernel.org/r/20191025195842.106825.71532.stgit@awfm-01.aw.intel.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
For a TID RDMA WRITE request, a QP on the responder side could be put into
a queue when a hardware flow is not available. A RNR NAK will be returned
to the requester with a RNR timeout value based on the position of the QP
in the queue. The tid_rdma_flow_wt variable is used to calculate the
timeout value and is determined by using a MTU of 4096 at the module
loading time. This could reduce the timeout value by half from the desired
value, leading to excessive RNR retries.
This patch fixes the issue by calculating the flow weight with the real
MTU assigned to the QP.
Fixes: 07b923701e ("IB/hfi1: Add functions to receive TID RDMA WRITE request")
Link: https://lore.kernel.org/r/20191025195836.106825.77769.stgit@awfm-01.aw.intel.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64a6ea39-3e4b-2ebe-74f7-98720e581e3e@web.de
If an hfi1 card is inserted in a Gen4 systems, the driver will avoid the
gen3 speed bump and the card will operate at half speed.
This is because the driver avoids the gen3 speed bump when the parent bus
speed isn't identical to gen3, 8.0GT/s. This is not compatible with gen4
and newer speeds.
Fix by relaxing the test to explicitly look for the lower capability
speeds which inherently allows for gen4 and all future speeds.
Fixes: 7724105686 ("IB/hfi1: add driver files")
Link: https://lore.kernel.org/r/20191101192059.106248.1699.stgit@awfm-01.aw.intel.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: James Erwin <james.erwin@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support for AXI Multichannel Direct Memory Access (AXI MCDMA)
core, which is a soft Xilinx IP core that provides high-bandwidth
direct memory access between memory and AXI4-Stream target peripherals.
The AXI MCDMA core provides scatter-gather interface with multiple
independent transmit and receive channels. The driver supports
device_prep_slave_sg slave transfer mode.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571763622-29281-7-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds the iWARP specific doorbells to the doorbell recovery
mechanism.
Link: https://lore.kernel.org/r/20191030094417.16866-9-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Extend dma_config structure to store irq routine handle. It enables runtime
handler selection based on xdma_ip_type and serves as preparatory patch for
adding MCDMA IP support.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Suggested-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/1571763622-29281-6-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use the doorbell recovery mechanism to register rdma related doorbells
that will be restored in case there is a doorbell overflow attention.
Link: https://lore.kernel.org/r/20191030094417.16866-8-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The AXI DMA multichannel support is deprecated in the IP and it is no
longer actively supported. For multichannel support, refer to the AXI
multichannel direct memory access IP product guide(PG228) and MCDMA
driver. So inline with it remove axidma multichannel support from
from the driver.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571763622-29281-5-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove all functions related to mmap from qedr and use the common API.
Link: https://lore.kernel.org/r/20191030094417.16866-7-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Remove the functions related to managing the mmap_xa database. This code
is now common in ib_core.
Link: https://lore.kernel.org/r/20191030094417.16866-6-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com>
Reviewed-by: Bernard Metzler <bmt@zurich.ibm.com>
Tested-by: Bernard Metzler <bmt@zurich.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Remove the functions related to managing the mmap_xa database. This code
was replaced with common code in ib_core.
Link: https://lore.kernel.org/r/20191030094417.16866-5-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The rdma_user_mmap_io interface created a common interface for drivers to
correctly map hw resources and zap them once the ucontext is destroyed
enabling the drivers to safely free the hw resources.
However, this meant the drivers need to delay freeing the resource to the
ucontext destroy phase to ensure they were no longer mapped. The new
mechanism for a common way of handling user/driver address mapping enabled
notifying the driver if all umap_priv mappings were removed, and enabled
freeing the hw resources when they are done with and not delay it until
ucontext destroy.
Since not all drivers use the mechanism, NULL can be sent to the
rdma_user_mmap_io interface to continue working as before. Drivers that
use the mmap_xa interface can pass the entry being mapped to the
rdma_user_mmap_io function to be linked together.
Link: https://lore.kernel.org/r/20191030094417.16866-4-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Create some common API's for adding entries to a xa_mmap. Searching for
an entry and freeing one.
The general approach is copied from the EFA driver and improved to be more
general and do more to help the drivers. Integration with the core allows
a reference counted scheme with a free function so that the driver can
know when its mmaps are all gone.
This significant new functionality will be helpful for drivers to have the
correct lifetime model for mmap objects.
Link: https://lore.kernel.org/r/20191030094417.16866-3-michal.kalderon@marvell.com
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add devicetree binding for Xilinx AXI Multichannel Direct Memory Access
(AXI MCDMA) IP. The AXI MCDMA provides high-bandwidth direct memory
access between memory and AXI4-Stream target peripherals. The AXI MCDMA
core provides a scatter-gather interface with multiple channel support
with independent configuration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1571763622-29281-4-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Trivial formatting(keep compatible string one per line, caps change etc).
It doesn't modify the content of the binding.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1571763622-29281-3-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The AXI DMA multichannel support is deprecated in the IP and it is no
longer actively supported. For multichannel support, refer to the AXI
multichannel direct memory access IP product guide(PG228) and MCDMA
driver(added in the subsequent commits). Inline with it remove axidma
multichannel optional properties i.e xlnx,mcdma and dma-channels from
the binding description.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1571763622-29281-2-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add USB ID for MOXA UPort 2210. This device contains mos7820 but
it passes GPIO0 check implemented by driver and it's detected as
mos7840. Hence product id check is added to force mos7820 mode.
Signed-off-by: Pavel Löbl <pavel@loebl.cz>
Cc: stable <stable@vger.kernel.org>
[ johan: rename id defines and add vendor-id check ]
Signed-off-by: Johan Hovold <johan@kernel.org>
