[Why]
* Clk Mgr DTO update point did not cover all needed updates, as it included a
check for plane_state which does not exist yet when the updater is called on
driver startup
* This resulted in another update path in the pipe programming sequence, based
on a dppclk update flag
* However, this alternate path allowed for stray DTO updates, some of which would
occur in the wrong order during dppclk lowering and cause underflow
[How]
* Remove plane_state check and use of plane_res.dpp->inst, getting rid
of sequence dependencies (this results in extra dto programming for unused
pipes but that doesn't cause issues and is a small cost)
* Allow DTOs to be updated even if global clock is equal, to account for
edge case exposed by diags tests
* Remove update_dpp_dto call in pipe programming sequence (leave update to
dppclk_control there, as that update is necessary and shouldn't occur in clk
mgr)
* Remove call to optimize_bandwidth when committing state, as it is not needed
and resulted in sporadic underflows even with other fixes in place
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
BT.2390 EETF is used for tone mapping/range reduction.
Say display is 0.1 - 500 nits.
The problematic case is when content is 0-400. We apply EETF because
0<0.1 so we need to reduce the range by 0.1.
In the commit, we ignore the bottom range. Most displays map 0 to min and
then have a ramp to 0.1, so sending 0.1 is actually >0.1.
Furthermode, HW that uses 3D LUT also assumes min=0.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU does not keep the wm table across S3, S4, need to re-send
the table. Also defer sending the cable to after DCN bave initialized
[How]
Send table at end of init hw
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A display that supports DRR can never really be considered
"synchronized" with any other display because we can dynamically
enable DRR (i.e. without modeset). this will cause their
relative CRTC positions to drift and lose sync. this will disrupt
features such as MCLK switching that assume and depend on
their permanent alignment (that can only change with modeset)
[how]
check for ignore_msa in stream when considered synchronizability
this ignore_msa is basically actually implemented as "supports drr"
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When aux engine acquire fails, we missed populating the operation_result
that describes the failure reason.
[How]
Set operation_result to new type:
AUX_CHANNEL_OPERATION_FAILED_ENGINE_ACQUIRE
in the case aux engine acquire has failed.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
force_single_disp_pipe_split is a debug flag for use on DCN1
but isn't necessary otherwise as DCN2+ splits by default
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c_read is called to differentiate passive DP->HDMI and DP->DVI-D dongles
The call is expected to fail in DVI-D case but pass in HDMI case
Some HDMI dongles have a chance to fail as well, causing misdetection as DVI-D
[HOW]
Retry i2c_read to ensure failed result is valid
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The enum value for TRANSMITTER_UNIPHY_G is 9. In resource dc_xx_resource
file structure link_enc_regs[], the TRANSMITTER_UNIPHY_G registers are
initialized at index 6. Due to this mismatch, if monitor is attached to
port using TRANSMITTER_UNIPHY_G then the monitor blanks out.
[How]
add function map_transmitter_id_to_phy_instance() and use the function
to map enum transmitter to link regs.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
SLT tests require that diag can drive eDP even if nothing is connected, this is not
typical production use case, so we need to add flag
[how]
add flag, and this flag supercedes "should destroy" logic
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are specific to dcn21 and should not be increased for
reuse on other asics.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
vm should be enabled by default for rn to get
right dml.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There's a use case for inverted gamma
and it's been confirmed that negative slopes are ok.
[how]
Remove code for blocking non-monotonically increasing gamma
Signed-off-by: Aidan Yang <Aidan.Yang@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV12 has lower min dcfclk
[How]
Add update in update_bounding_box
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some systems, we need to check the dcn version in runtime
system, not in compile time.
[How]
Stub in dcn version parameter to find_first_free_audio
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DML is incorrectly initialized with 4 pipes on 3 pipe configs
RequiredDPPCLK is halved on unsplit pipe due to an incorrectly handled 3 pipe
case, causing underflow with 2 planes & pipe split (MPO, 8K + 2nd display)
[HOW]
Set correct number of DPP/OTGs for dml init to generate correct DPP topology
Double RequiredDPPCLK after clock is halved for pipe split
and find_secondary_pipe fails to fix underflow
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This value will be needed by dml and therefore should be externally
accessible.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
One of odm variables was not initialized in dml.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split a large function into smaller, reusable chunks.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In diags environment we are not programming the DPP DTO
correctly.
[How]
Populate the dpp refclk in dccg so it can be used to correctly
program DPP DTO.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR (Panel Self-Refresh) is a power-saving feature for eDP panels.
The feature has support in DMCU (Display MicroController Unit).
DMCU/driver communication is implemented in DC.
DM can use existing DC PSR interface to use PSR feature.
[How]
- Read psr caps via dpcd
- Send vsc infoframe if panel supports psr
- Disable psr before h/w programming (FULL_UPDATE)
- Enable psr after h/w programming
- Disable psr for fb console
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For upcoming PSR stupport it's useful to have debug entry
to verify psr state.
[How]
- Enable psr dc api for Linux
- Add psr_state file to eDP connector debugfs
usage e.g.: cat /sys/kernel/debug/dri/0/DP-1/psr_state
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit hints are unnecessary after front end programming redesign.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For loop below the assert already checks for the number of instances to
create. ASSERT is meaningless and causing spam.
[How]
dd
Signed-off-by: Jordan Lazare <Jordan.Lazare@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Optimized gamma22 assumes fixed point distribution which is not true
for eetf true.
[how]
Use long calculation for eetf.
Signed-off-by: Aidan Yang <Aidan.Yang@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System hang during S0i3 if DP only connected due to clk is disabled when
doing link training.
During S0i3, clk is disabled while the clk state is updated when ini_hw
called, and at the moment clk is still disabled which indicating a wrong
state for next time trying to enable clk.
[How]
Add an unknown state and initialize it during int_hw, make sure enable clk
command be sent to smu.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Hard to determine if pipe combine is done with MPC or ODM
[how]
Add new visual confirm type, this will mark each MPCC tree
with a different color
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While setting hdmi_vic, hv_frame.vic is not initialized and might
assign a wrong value to hdmi_vic. Cause to send out VSIF with
abnormal value.
[How]
Initialize hv_frame and avi_frame
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To fit the latest SMU firmware.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a DRM_ERROR error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're leaking memory by not freeing the gamma used to calculate the
transfer function for legacy gamma.
[How]
Release the gamma after we're done with it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This patch is for fixing Navi14 HDMI display pink screen issue.
[How]
Call stream->link->link_enc->funcs->setup twice. This is setting
the DIG_MODE to the correct value after having been overridden by
the call to transmitter control.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid walking past the end of the arrays since the PP_SMU
defines don't match the renoir defines.
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_vm_prt_fini uses "vm->root.base.bo" so it must still be valid when
we call it.
Fixes: b65709a921 ("drm/amdgpu: reserve the root PD while freeing PASIDs")
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In i40e_setup_macvlans if i40e_setup_channel fails the allocated memory
for ch should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prepares ground for the next VF MAC address change fix.
It lets untrusted VF to delete any VF mac filter, but it still
doesn't let untrusted VF to add mac filter not setup by PF.
It removes information duplication in num_mac mac filters counter.
And improves exact h/w mac filters usage checking in the
i40e_check_vf_permission() function by counting mac2add_cnt.
It also improves logging because now all mac addresses will be validated
first and corresponding messages will be logged.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Add X710T*L device specific operations (in port LED detection and
handling of GLGEN_GPIO_CTL.PIN_FUNC field) to enable LED blinking.
Signed-off-by: Damian Milosek <damian.milosek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Let ethtool print driver and firmware versions when NIC is in
recovery mode. Assign i40e_get_drvinfo() operation to ethtool
recovery mode operations. Previously ethtool did not report
driver and firmware versions when NIC was in recovery mode.
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 92418fb147 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN/ITR0 registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently FW use MDIO I/F number corresponded with current PF for PHY
access. This code allow to specify used MDIO I/F number.
Add new field - command flags with only one flag for now. Added flag
tells FW that it shouldn't change page while accessing QSFP module, as
it was set manually.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move code detecting HW flags based on device type and FW API version
into a single function.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix display of parameters "Configured FEC encodings:" and "Advertised
FEC modes:" in ethtool. Implemented by setting proper FEC bits in
“advertising” bitmask of link_modes struct and “fec” bitmask in
ethtool_fecparam struct. Without this patch wrong FEC settings
can be shown.
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.
Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
nbd requires socket families to support the shutdown method so the nbd
recv workqueue can be woken up from its sock_recvmsg call. If the socket
does not support the callout we will leave recv works running or get hangs
later when the device or module is removed.
This adds a check during socket connection/reconnection to make sure the
socket being passed in supports the needed callout.
Reported-by: syzbot+24c12fa8d218ed26011a@syzkaller.appspotmail.com
Fixes: e9e006f5fc ("nbd: fix max number of supported devs")
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
