In adis_update_scan_mode_burst, if adis->buffer allocation fails release
the adis->xfer.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* fix for an ACPI table parsing bug;
* a fix for a NULL pointer dereference in the cfg with specific
devices;
* fix the rb_allocator;
* prevent multiple phy configuration with new devices;
* fix a race-condition in the rx queue;
* prevent a couple of memory leaks;
* fix initialization of 3168 devices (the infamous BAD_COMMAND bug);
* fix recognition of some newer systems with integrated MAC;
-----BEGIN PGP SIGNATURE-----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=/62J
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2019-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
First batch of fixes intended for v5.4
* fix for an ACPI table parsing bug;
* a fix for a NULL pointer dereference in the cfg with specific
devices;
* fix the rb_allocator;
* prevent multiple phy configuration with new devices;
* fix a race-condition in the rx queue;
* prevent a couple of memory leaks;
* fix initialization of 3168 devices (the infamous BAD_COMMAND bug);
* fix recognition of some newer systems with integrated MAC;
Currently the property docs don't specify whether it's okay for two planes to
have the same zpos value and what user-space should expect in this case.
The unspoken, legacy rule used in the past was to make user-space figure
out the zpos from object IDs. However some drivers break this rule,
that's why the ordering is documented as unspecified in case the zpos
property is missing. User-space should rely on the zpos property only.
There are some cases in which user-space might read identical zpos
values for different planes.
For instance, in case the property is mutable, user-space might set two
planes' zpos to the same value. This is necessary to support user-space
using the legacy DRM API where atomic commits are not possible:
user-space needs to update the planes' zpos one by one.
Because of this, user-space should handle multiple planes with the same
zpos.
While at it, remove the assumption that zpos is only for overlay planes.
Additionally, update the drm_plane_state.zpos docs to clarify that zpos
disambiguation via plane object IDs is a recommendation for drivers, not
something user-space can rely on. In other words, when user-space sets
the same zpos on two planes, drivers should rely on the plane object ID.
v2: clarify drm_plane_state.zpos docs (Daniel)
v3: zpos is for all planes (Marius, Daniel)
v4: completely reword the drm_plane_state.zpos docs to make it clear the
recommendation to use plane IDs is for drivers in case user-space uses
duplicate zpos values (Pekka)
v5: reword commit message (Pekka, James)
v6: remove mention of Arm GPUs having planes which can't overlap,
because this isn't uAPI yet (Daniel)
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Marius Vlad <marius.vlad@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: James Qian Wang <james.qian.wang@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/T5nHrvXH0GKOp6ONaFHk-j2cwEb4_4C_sBz9rNw8mmPACuut-DQqC74HMAFKZH3_Q15E8a3YnmKCxap-djKA71VVZv_T-tFxaB0he13O7yA=@emersion.fr
We'll end up with debugfs collisions if we don't give names to the
regmaps created by this driver. Change the name of the config before
registering it so we don't collide in debugfs.
Fixes: 7f9c136216 ("soc: qcom: Add broadcast base for Last Level Cache Controller (LLCC)")
Cc: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since the "dma-ranges" property is only valid for a node representing a
bus, of_dma_get_range() currently assumes the node passed in is a leaf
representing a device, and starts the walk from its parent. In cases
like PCI host controllers on typical FDT systems, however, where the PCI
endpoints are probed dynamically the initial leaf node represents the
'bus' itself, and this logic means we fail to consider any "dma-ranges"
describing the host bridge itself. Rework the logic such that
of_dma_get_range() also works correctly starting from a bus node
containing "dma-ranges".
While this does mean "dma-ranges" could incorrectly be in a device leaf
node, there isn't really any way in this function to ensure that a leaf
node is or isn't a bus node.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[robh: Allow for the bus child node to still be passed in]
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-npcm-pspi.c: In function npcm_pspi_handler:
drivers/spi/spi-npcm-pspi.c:296:6: warning: variable val set but not used [-Wunused-but-set-variable]
It is not used since commit 2a22f1b30c ("spi:
npcm: add NPCM PSPI controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1570581437-104549-3-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-omap-100k.c: In function spi100k_read_data:
drivers/spi/spi-omap-100k.c:140:6: warning: variable dataH set but not used [-Wunused-but-set-variable]
It is not used since commit 35c9049b27 ("Add OMAP spi100k driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1570581437-104549-2-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When debug is enabled compiler cannot find the definition of
clk_get_rate resulting in the following error:
./include/sound/simple_card_utils.h:168:40: note: previous implicit
declaration of ‘clk_get_rate’ was here
dev_dbg(dev, "%s clk %luHz\n", name, clk_get_rate(dai->clk));
./include/sound/simple_card_utils.h:168:3: note: in expansion of macro
‘dev_dbg’
dev_dbg(dev, "%s clk %luHz\n", name, clk_get_rate(dai->clk));
Fix this by including the appropriate header.
Fixes: 0580dde594 ("ASoC: simple-card-utils: add asoc_simple_debug_info()")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20191009153615.32105-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_debug_info and asoc_simple_debug_dai must be static
otherwise we might a compilation error if the compiler decides
not to inline the given function.
Fixes: 0580dde594 ("ASoC: simple-card-utils: add asoc_simple_debug_info()")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20191009153615.32105-3-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing MIX2 path on RX1/2 which take IIR1 and
IIR2 as inputs.
Without this patch sound card fails to intialize with below warning:
ASoC: no sink widget found for RX1 MIX2 INP1
ASoC: Failed to add route IIR1 -> IIR1 -> RX1 MIX2 INP1
ASoC: no sink widget found for RX2 MIX2 INP1
ASoC: Failed to add route IIR1 -> IIR1 -> RX2 MIX2 INP1
ASoC: no sink widget found for RX1 MIX2 INP1
ASoC: Failed to add route IIR2 -> IIR2 -> RX1 MIX2 INP1
ASoC: no sink widget found for RX2 MIX2 INP1
ASoC: Failed to add route IIR2 -> IIR2 -> RX2 MIX2 INP1
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191009111944.28069-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Various minor bug fixes posted in the last couple of weeks:
- Various missed memory frees and error unwind bugs
- Fix regressions in a few iwarp drivers from 5.4 patches
- A few regressions added in past kernels
- Squash a number of races in mlx5 ODP code
-----BEGIN PGP SIGNATURE-----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=sgve
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"The usual collection of driver bug fixes, and a few regressions from
the merge window. Nothing particularly worrisome.
- Various missed memory frees and error unwind bugs
- Fix regressions in a few iwarp drivers from 5.4 patches
- A few regressions added in past kernels
- Squash a number of races in mlx5 ODP code"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Add missing synchronize_srcu() for MW cases
RDMA/mlx5: Put live in the correct place for ODP MRs
RDMA/mlx5: Order num_pending_prefetch properly with synchronize_srcu
RDMA/odp: Lift umem_mutex out of ib_umem_odp_unmap_dma_pages()
RDMA/mlx5: Fix a race with mlx5_ib_update_xlt on an implicit MR
RDMA/mlx5: Do not allow rereg of a ODP MR
IB/core: Fix wrong iterating on ports
RDMA/nldev: Reshuffle the code to avoid need to rebind QP in error path
RDMA/cxgb4: Do not dma memory off of the stack
RDMA/cm: Fix memory leak in cm_add/remove_one
RDMA/core: Fix an error handling path in 'res_get_common_doit()'
RDMA/i40iw: Associate ibdev to netdev before IB device registration
RDMA/iwcm: Fix a lock inversion issue
RDMA/iw_cxgb4: fix SRQ access from dump_qp()
RDMA/hfi1: Prevent memory leak in sdma_init
RDMA/core: Fix use after free and refcnt leak on ndev in_device in iwarp_query_port
RDMA/siw: Fix serialization issue in write_space()
RDMA/vmw_pvrdma: Free SRQ only once
Polaris and vegam use count for the value rather than
level. This looks like a copy paste typo from when
the code was adapted from previous asics.
I'm not sure that the SMU actually uses this value, so
I don't know that it actually is a bug per se.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=108609
Reported-by: Robert Strube <rstrube@gmail.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
cleanup error handling code and make sure temporary info array
with the handles are freed by amdgpu_bo_list_put() on
idr_replace()'s failure.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable devfreq events along with drivers for scaling frequency and
voltages of Exynos buses and Dynamic Memory Controller (DMC). This
usually brings energy saving benefits.
So far devfreq was disabled because it was causing hangs during system
reboot (voltage not matching reset frequency). This was already fixed.
Occasionally, devfreq might negatively impact performance of certain SoC
blocks, e.g. when a bus is scaled down but some block (like Mixer with
two Full HD windows) wants to perform high-throughput DMA operations.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Sync with exynos_defconfig and enable following options for Samsung
Exynos SoC based boards:
1. NFC_S3FWRN5_I2C (with NFC stack): Samsung S3FWRN5 NCI NFC Controller,
used for example on Exynos5433 (if booted in 32-bit mode),
2. S3C2410_WATCHDOG: watchdog driver used on S3C, S5P and Exynos SoCs,
3. REGULATOR_S2MPA01: Samsung S2MPA01 regulators driver present on
Exynos5260 RexNos REX-RED board,
4. SND_SOC_ARNDALE: sound support on Arndale boards,
5. EXYNOS_IOMMU: IOMMU driver used on all Exynos SocS,,
6. EXTCON_MAX14577, EXTCON_MAX77693 and EXTCON_MAX8997: extcon drivers
for handling micro USB on mobile Samsung boards (Trats, Trats2,
Rinato),
7. PHY_EXYNOS5250_SATA: SATA phy for Exynos5250 present on Arndale and
SMDK5250 boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
- Numerous fixes to the compat vDSO build system, especially when
combining gcc and clang
- Fix parsing of PAR_EL1 in spurious kernel fault detection
- Partial workaround for Neoverse-N1 erratum #1542419
- Fix IRQ priority masking on entry from compat syscalls
- Fix advertisment of FRINT HWCAP to userspace
- Attempt to workaround inlining breakage with '__always_inline'
- Fix accidental freeing of parent SVE state on fork() error path
- Add some missing NULL pointer checks in instruction emulation init
- Some formatting and comment fixes
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl2dv4cQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNO6UB/4yY3lYR6C++7EdVwYxQRXf8VX9ukeO76gp
P/AS6Kt8+AiOuhFJJXDj3D7K/KqgZnJEhzeWHTZluYpIBuzFerW+RxzmExL+wFWf
ISZgdh7roFCQx3Nt+iBs/bAMPvk5Da1KHvSw/yZ6P8mj6fK8sVUh/O8+KK4kSzfT
muDoSO6WHSonAEOYm9ryn1q1pM5DsCjr+9fm7d9L+dJAUP2xX44ymlIY+v6yD3Or
IWJMYaWKb4TbdTJSy2VbUSM0fzByGBJCx1wOTd4gV6uDbB4GA6h+E/DMB1qnvv9W
nH5c4qwVgYhp7prpescMxYZoV/I9damvfnaIjqh9jc3H3milEqcn
=GwLJ
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A larger-than-usual batch of arm64 fixes for -rc3.
The bulk of the fixes are dealing with a bunch of issues with the
build system from the compat vDSO, which unfortunately led to some
significant Makefile rework to manage the horrible combinations of
toolchains that we can end up needing to drive simultaneously.
We came close to disabling the thing entirely, but Vincenzo was quick
to spin up some patches and I ended up picking up most of the bits
that were left [*]. Future work will look at disentangling the header
files properly.
Other than that, we have some important fixes all over, including one
papering over the miscompilation fallout from forcing
CONFIG_OPTIMIZE_INLINING=y, which I'm still unhappy about. Harumph.
We've still got a couple of open issues, so I'm expecting to have some
more fixes later this cycle.
Summary:
- Numerous fixes to the compat vDSO build system, especially when
combining gcc and clang
- Fix parsing of PAR_EL1 in spurious kernel fault detection
- Partial workaround for Neoverse-N1 erratum #1542419
- Fix IRQ priority masking on entry from compat syscalls
- Fix advertisment of FRINT HWCAP to userspace
- Attempt to workaround inlining breakage with '__always_inline'
- Fix accidental freeing of parent SVE state on fork() error path
- Add some missing NULL pointer checks in instruction emulation init
- Some formatting and comment fixes"
[*] Will's final fixes were
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
but they were already in linux-next by then and he didn't rebase
just to add those.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (21 commits)
arm64: armv8_deprecated: Checking return value for memory allocation
arm64: Kconfig: Make CONFIG_COMPAT_VDSO a proper Kconfig option
arm64: vdso32: Rename COMPATCC to CC_COMPAT
arm64: vdso32: Pass '--target' option to clang via VDSO_CAFLAGS
arm64: vdso32: Don't use KBUILD_CPPFLAGS unconditionally
arm64: vdso32: Move definition of COMPATCC into vdso32/Makefile
arm64: Default to building compat vDSO with clang when CONFIG_CC_IS_CLANG
lib: vdso: Remove CROSS_COMPILE_COMPAT_VDSO
arm64: vdso32: Remove jump label config option in Makefile
arm64: vdso32: Detect binutils support for dmb ishld
arm64: vdso: Remove stale files from old assembly implementation
arm64: vdso32: Fix broken compat vDSO build warnings
arm64: mm: fix spurious fault detection
arm64: ftrace: Ensure synchronisation in PLT setup for Neoverse-N1 #1542419
arm64: Fix incorrect irqflag restore for priority masking for compat
arm64: mm: avoid virt_to_phys(init_mm.pgd)
arm64: cpufeature: Effectively expose FRINT capability to userspace
arm64: Mark functions using explicit register variables as '__always_inline'
docs: arm64: Fix indentation and doc formatting
arm64/sve: Fix wrong free for task->thread.sve_state
...
Don't populate the array register_offset on the stack but instead make it
static. Makes the object code smaller by 63 bytes. Also add the int type
specifier to clean up a checkpatch warning.
Before:
text data bss dec hex filename
9212 5712 1408 16332 3fcc drivers/gpio/gpio-104-idi-48.o
After:
text data bss dec hex filename
9085 5776 1408 16269 3f8d drivers/gpio/gpio-104-idi-48.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There's no need to emit an error message on probe failure unless we're
printing some meaningful info. Otherwise the core driver code will
inform us about a probe error. Also: the driver currently drops info
about errors propagated from called functions by default to returning
-EINVAL. This fixes it as well.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to emit an error message on probe failure unless we're
printing some meaningful info. Otherwise the core driver code will
inform us about a probe error.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add a check to disallow cross file systems copy offload, both
files are expected to be of NFS4.2+ type.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
For small file sizes, it make sense to issue a synchronous copy (and
save an RPC callback operation). Also, for the inter copy offload,
copy len must be larger than the cost of doing a mount between the
destination and source server (14RPCs are sent during 4.x mount).
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
When the source server reboots after a server-to-server copy was
issued, we need to retry the copy from COPY_NOTIFY. We need to
detect that the source server rebooted and there is a copy waiting
on a destination server and wake it up.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
When a destination server sends a READ to the source server it can
get a NFS4ERR_PARTNER_NO_AUTH, which means a copy needs to be
restarted.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
If server sends ERR_OFFLOAD_DENIED error, the client must fall
back on doing copy the normal way. Return ENOTSUPP to the vfs and
fallback to regular copy.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
If the client sends an "inter" copy to the destination server but
it only supports "intra" copy, it can return ESTALE (since it
doesn't know anything about the file handle from the other server
and does not recognize the special case of "inter" copy). Translate
this error as ENOTSUPP and also send OFFLOAD_CANCEL to the source
server so that it can clean up state.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Mark the open created for the source file on the destination
server. Then if this open is going thru a recovery, then fail
the recovery as we don't need to be recoving a "fake" open.
We need to fail the ongoing READs and vfs_copy_file_range().
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
NFSv4.2 inter server to server copy requires the destination server to
READ the data from the source server using the provided stateid and
file handle.
Given an NFSv4 stateid and filehandle from the COPY operaion, provide the
destination server with an NFS client function to create a struct file
suitable for the destiniation server to READ the data to be copied.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Andy Adamson <andros@netapp.com>
Support only one source server address: the same address that
the client and source server use.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Try using the delegation stateid, then the open stateid.
Only NL4_NETATTR, No support for NL4_NAME and NL4_URL.
Allow only one source server address to be returned for now.
To distinguish between same server copy offload ("intra") and
a copy between different server ("inter"), do a check of server
owner identity and also make sure server is capable of doing
a copy offload.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
These structures are needed by COPY_NOTIFY on the client and needed
by the nfsd as well
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Add PRM instance data for omap5 family of SoCs. Initially this is just
used to provide reset support.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add PRM instance data for am4 family of SoCs. Initially this is just
used to provide reset support.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add PRM instance data for dra7 family of SoCs. Initially this is just
used to provide reset support.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Add PRM instance data for AM33xx SoC. Includes some basic register
definitions and reset data for now.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
