8822C is a 2x2 11ac chip, and then NSS must be less or equal to 2. However,
current nss of hw cap is 3, likes
hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=3
This commit adds constraint to make sure NSS <= rf_path_num, and result
looks like
hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=2
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit doesn't change logic at all, just use struct rtw_fw_hdr to
access fixed part of 64 bytes header. Since remaining part is variable
length data of actual firmware, we don't define them within the struct.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's better to print firmware version at load time.
But since we need to set debug_mask properly to default print
rtw_dbg(), raise the debug level to rtw_info() instead.
Also change the multiple line style to one line only, it will
be easier for log analyzing.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set CWmax/CWmin, TXOP and AIFS according to ieee80211_tx_queue_params.
Do note that hardware has only one group of EDCA[ac] registers, if more
than one vif are added, the EDCA[ac] registers will contain value of
params of the most recent set by ieee80211_ops::conf_tx().
And AIFS = AIFSN[ac] * slot_time + SIFS, so if use_short_slot is changed,
need to also change AIFS.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value of GET_RX_DESC_SWDEC() indicates that if this RX
packet requires software decryption or not. And software
decryption is required when the packet was encrypted and the
hardware failed to decrypt it.
So, GET_RX_DESC_SWDEC() is negative does not mean that this
packet is decrypted, it might just have no encryption at all.
To actually see if the packet is decrypted, driver needs to
further check if the hardware has successfully decrypted it,
with a specific type of encryption algorithm.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When downloading the reserved page, the first page always contains
a beacon for the firmware to reference. For non-beaconing modes such
as station mode, also put a blank skb with length=1.
And for the beaconing modes, driver will get a real beacon with a
length approximate to the page size. But as the beacon is always put
at the first page, it does not need a tx_desc, because the TX path
will generate one when TXing the reserved page to the hardware. So we
could allocate a buffer with a size smaller than the reserved page,
when using memcpy() to copy the content of reserved page to the buffer,
the over-sized reserved page will violate the kernel memory.
To fix it, add the tx_desc before memcpy() the reserved packets to
the buffer, then we can get SKBs with correct length when counting
the pages in total. And for page 0, count the extra tx_desc_sz that
the TX path will generate. This way, the first beacon that allocated
without tx_desc can be counted with the extra tx_desc_sz to get
actual pages it requires.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes mac80211 will ask us to flush the hardware queues.
To flush them, first we need to get the corresponding priority queues
from the RQPN mapping table.
Then we can check the available pages are equal to the originally
reserved pages, which means the hardware has returned all of the pages
it used to transmit.
Note that now we only check for 100 ms for the priority queue, but
sometimes if we have a lot of traffic (ex. 100Mbps up), some of the
packets could be dropped.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Based on the mac80211's TXQ implementation, TX-AMSDU can
be used to get higher MAC efficiency. To make mac80211
aggregate MSDUs, low level driver just need to leave skbs
in the TXQ, and mac80211 will try to aggregate them if
possible. As driver will schedule a tasklet when the TX
queue is woke, until the tasklet being served, there will
have some skbs in the queue if traffic is heavy.
Driver can control the max AMSDU size depending on the
current bit rate used by hardware/firmware. The higher
rates are used, the larger AMSDU size can be.
It is tested that can achieve higher T-Put at higher rates.
If the environment is relatively clean, and the bit_rate
is high enough, we can get about 80Mbps improvement.
For lower bit rates, not much gain can we get, so leave
the max_amsdu length low to prevent aggregation.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the firmware increases/decreases the bit rate used
to transmit to a peer, it sends an RA report through C2H to
driver. Driver can then record the bit rate in the peer's
struct rtw_sta_info, and report to mac80211 when it asks us
for the statistics of the sta by ieee80211_ops::sta_statistics
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can indicate IEEE80211_HW_HAS_RATE_CONTROL to mac80211 because
the hardware has its own rate control algorithm. And what driver needs
to do is to choose an RA mask according the peer's capabilities.
But the hardware is not able to setup BA session by itself. So driver
requires to initiate tx BA session for hardware, and tells it if it is
possible to transmit AMPDU. The hardware can then aggregate MPDUs.
And the size of AMPDU is controlled by the TX descriptor and the
register value. Since the TX descriptor will reference the max AMPDU
size from ieee80211_sta::ht_cap::ampdu_factor, just set the register
value to 0x3f, and let it be controlled by TX descriptor.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mac80211 provides software TX queue for driver, as long as
driver has hooked ieee80211_ops::wake_tx_queue. Each time a
packet is queued onto the TX queue, that queue will be woken
up the inform driver to serve the queue.
Now driver only supports PCI interface ICs, there's no specific
traffic control for each queue, just schedule a tasklet, and
dump all of the packets at once to the DMA ring. Instead of TX
the packets whenever TX queue is woke, tasklet handler can have
more packets dumped to the device, takes advantage of burst
write with DMA engine.
And if the driver is going to support USB/SDIO ICs, the tasklet
can be more flexible for aggregating the packets, enhance the
efficiency of bandwidth usage.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allows driver to send RTS by filling tx descriptor.
The user may want to set the rts threshold. But since we have not
been taking over rate control from mac80211 to driver by setting flag
IEEE80211_HW_HAS_RATE_CONTROL, there is nothing we can do about it.
So here just store the value, and mac80211 will tell us to use rts
protection by ieee80211_tx_info::control::use_rts.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver needs to wait for firmware to restore hardware setting
to active mode after leaving lps.
After getting H2C from driver for leaving lps, firmware will
issue null packet without PS bit to inform AP driver is active,
and then restore REG_TCR Register if AP has receiced null packet.
But the transmission of null packet may cost much more time
in noisy environment. If driver does not wait for firmware,
null packet with PS bit could be sent due to incorrect REG_TCR setting.
And AP will be confused.
In our test, 100ms is enough for firmware to send null packet
to AP. If REG_TCR Register is still wrong after 100ms, we will
modify it directly, force the PS bit to be cleared
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Both kvm_s390_gib_destroy and debug_unregister test if the needed
pointers are not NULL and hence can be called unconditionally.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/kvm/20191002075627.3582-1-frankja@linux.ibm.com
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
It's not required, so drop it to make it clear that this interrupt
does not have any extra parameters.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Link: https://lore.kernel.org/kvm/20190912070250.15131-1-thuth@redhat.com
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The L3 cache remapping is stored as u32 elements, and we should ensure
that the user only supplies complete slice information(u32).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004105958.1741-1-chris@chris-wilson.co.uk
Fix tty driver build on SPARC by not using __exitdata.
It appears that SPARC does not support section .exit.data.
Fixes these build errors:
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 063246641d ("format-security: move static strings to const")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/675e7bd9-955b-3ff3-1101-a973b58b5b75@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two parts which should be fixed. The first one is to assigned
uartps_major at the end of probe() to avoid complicated logic when
something fails.
The second part is initialized uartps_major number to 0 when last device is
removed. This will ensure that on next probe driver will ask for new
dynamic major number.
Fixes: ab26266601 ("serial: uartps: Use the same dynamic major number for all ports")
Reported-by: Paul Thomas <pthomas8589@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d2652cda992833315c4f96f06953eb547f928918.1570194248.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the comment of tty_port_destroy():
When a port was initialized using tty_port_init, one has to destroy
the port by tty_port_destroy();
tty_port_init() is called in gsm_dlci_alloc()
so tty_port_destroy() needs to be called in gsm_dlci_free()
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Link: https://lore.kernel.org/r/1569317156-45850-1-git-send-email-nixiaoming@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have got existing macro to check for CONFIG option, use it.
Signed-off-by: Pavel Machek <pavel@denx.de>
Link: https://lore.kernel.org/r/20190924083244.GA4344@amd
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add documentation for 8250_aspeed_vuart's aspeed,sirq-polarity-sense
property that enables to auto-configure the VUART's SIRQ polarity.
Signed-off-by: Oskar Senft <osk@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190905144130.220713-2-osk@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the SIRQ polarity for Aspeed AST24xx/25xx VUART configurable via
sysfs. This setting need to be changed on specific host platforms
depending on the selected host interface (LPC / eSPI).
The setting is configurable via sysfs rather than device-tree to stay in
line with other related configurable settings.
On AST2500 the VUART SIRQ polarity can be auto-configured by reading a
bit from a configuration register, e.g. the LPC/eSPI interface
configuration bit.
Tested: Verified on TYAN S7106 mainboard.
Signed-off-by: Oskar Senft <osk@google.com>
Link: https://lore.kernel.org/r/20190905144130.220713-1-osk@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call uart_unregister_driver() conditionally instead of
unconditionally, only if it has been previously registered.
This uses driver.state, just as the sh-sci.c driver does.
Fixes this null pointer dereference in tty_unregister_driver(),
since the 'driver' argument is null:
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:tty_unregister_driver+0x25/0x1d0
Fixes: 238b8721a5 ("[PATCH] serial uartlite driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: stable <stable@vger.kernel.org>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Link: https://lore.kernel.org/r/9c8e6581-6fcc-a595-0897-4d90f5d710df@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following an incorrect indentation reported to me by Dan Carpenter, I
noticed that the SysRq lines were inherited from the lpuart driver[1] (note
how the 'continue' is aligned to 'sport->port.sysrq = 0') and we have never
actually tested the SysRq support.
'sport->sysrq = 0' is not necessary neither before nor after 'continue',
because sysrq will already be 0 after uart_handle_sysrq_char() will finish.
Also, since the LINFlexD driver never called uart_handle_break(), sysrq
would have never been set to a nonzero value, so uart_handle_sysrq_char()
was not going to do anything.
Break conditions are detected based on a null data byte along with a
framing error (stop bit sampled to 0).
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/tty/serial/fsl_lpuart.c?h=b3e3bf2ef2c74f5ce5c19510edbbb9bfc1d249c2#n659
Fixes: 09864c1cdf ("tty: serial: Add linflexuart driver for S32V234")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190918184439.7465-1-stefan-gabriel.mirea@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, scary warnings may be printed for optional interrupts:
sh-sci e6550000.serial: IRQ index 1 not found
sh-sci e6550000.serial: IRQ index 2 not found
sh-sci e6550000.serial: IRQ index 3 not found
sh-sci e6550000.serial: IRQ index 4 not found
sh-sci e6550000.serial: IRQ index 5 not found
Fix this by calling platform_get_irq_optional() instead for all but the
first interrupts, which are optional.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191001180743.1041-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RZ/G2N (R8A774B1) SoC also has the R-Car Gen3 compatible SCIF and
HSCIF ports, so document the SoC specific bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1568724324-26995-1-git-send-email-biju.das@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sifive serial driver implements earlycon support, but unless
another driver is built in that supports earlycon support it won't
be usable. Explicitly select SERIAL_EARLYCON instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Link: https://lore.kernel.org/r/20190910055923.28384-1-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). This comes with a small functional change: previously
all errors were ignored except deferred probe. Now all errors are
treated as errors. If no input clock is present devm_clk_get_optional() will
return NULL instead of an error which matches the behavior of the old code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190925162617.30368-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices support MSI interrupts. Let's at least try to use them in
platforms that provide MSI capability.
While at that, remove the now duplicated code from qrp_serial_setup().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191001115825.795700-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_dma_probe() is only used in pl011_dma_startup() which does only
exist when CONFIG_DMA_ENGINE=y, so remove the unused dummy version to
silence the warning.
Signed-off-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/1568726340-4518-1-git-send-email-cai@lca.pw
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason for this patch is xilinx_uartps driver which create one dynamic
instance per IP with unique major and minor combinations. drv->nr is in
this case all the time setup to 1. That means that uport->line is all the
time setup to 0 and drv->tty_driver->name_base is doing shift in name to
for example ttyPS3.
register_console() is looping over console_cmdline array and looking for
proper name/index combination which is in our case ttyPS/3.
That's why every instance of driver needs to be registered with proper
combination of name/number (ttyPS/3). Using uport->line is doing
registration with ttyPS/0 which is wrong that's why proper console index
should be used which is in cons->index field.
Also it is visible that recording console should be done based on
information about console not about the port but in most cases numbers are
the same and xilinx_uartps is only one exception now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/4a877f1c7189a7c45b59a6ebfc3de607e8758949.1567434470.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use software emulated RS485 direction control to provide RS485 API
Currently it is not possible to use rs485 as pointer to
rs485_config struct in struct uart_port is NULL in case we
configure the port through device tree.
Signed-off-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/r/20190913050105.1132080-1-hs@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to access the UART without the interrupts, the kernel uses
the basic polling methods for IO with the device. With these methods
implemented, it is now possible to enable kgdb during early boot over serial.
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/f112a741c053ac5fb0637e2f058be81e17f78ccc.1568862391.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using only 4 DMA periods for UART RX is very few if we have a high
frequency of small transfers - like in our case using Bluetooth with
many small packets via UART - causing many dma transfers but in each
only filling a fraction of a single buffer. Such a case may lead to
the situation that DMA RX transfer is triggered but no free buffer is
available. When this happens dma channel ist stopped - with the patch
"dmaengine: imx-sdma: fix dma freezes" temporarily only - with the
possible consequences that:
with disabled hw flow control:
If enough data is incoming on UART port the RX FIFO runs over and
characters will be lost. What then happens depends on upper layer.
with enabled hw flow control:
If enough data is incoming on UART port the RX FIFO reaches a level
where CTS is deasserted and remote device sending the data stops.
If it fails to stop timely the i.MX' RX FIFO may run over and data
get lost. Otherwise it's internal TX buffer may getting filled to
a point where it runs over and data is again lost. It depends on
the remote device how this case is handled and if it is recoverable.
Obviously we want to avoid having no free buffers available. So we
decrease the size of the buffers and increase their number and the
total buffer size.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20190923135916.1212-1-philipp.puschmann@emlix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few callers need to serialise the destruction of their drm_mm_node and
ensure it is removed from the drm_mm before freeing. However, to be
completely sure that any access from another thread is complete before
we free the struct, we require the RELEASE semantics of
clear_bit_unlock().
This allows the conditional locking such as
Thread A Thread B
mutex_lock(mm_lock); if (drm_mm_node_allocated(node)) {
drm_mm_node_remove(node); mutex_lock(mm_lock);
mutex_unlock(mm_lock); if (drm_mm_node_allocated(node))
drm_mm_node_remove(node);
mutex_unlock(mm_lock);
}
kfree(node);
to serialise correctly without any lingering accesses from A to the
freed node. Allocation / insertion of the node is assumed never to race
with removal or eviction scanning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003210100.22250-5-chris@chris-wilson.co.uk
A straightforward conversion of assignment and checking of the boolean
state flags (allocated, scanned) into non-atomic bitops. The caller
remains responsible for all locking around the drm_mm and its nodes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003210100.22250-4-chris@chris-wilson.co.uk
On platfroms with gen10+ display, driver must set the enable bit of
AUDIO_PIN_BUF_CTL register before transactions with the HDA controller
can proceed. Add setting this bit to the audio power up sequence.
Failing to do this resulted in errors during display audio codec probe,
and failures during resume from suspend.
Note: We may also need to disable the bit afterwards, but there are
still unresolved issues with that.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111214
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003085531.30990-1-kai.vehmanen@linux.intel.com
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Note that runtime PM has never actually been enabled for this driver
since the support_autosuspend flag in its usb_driver struct is not set.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the original bindings that were superseeded by the YAML schemas
didn't mention that phy-names was needed, it turns out that phy-names is
required if phys is set according to phy/phy-bindings.txt.
Let's add back those properties.
Fixes: 14ec072a19 ("dt-bindings: usb: Convert USB HCD generic binding to YAML")
Fixes: c93bcace10 ("dt-bindings: usb: Convert the generic OHCI binding to YAML")
Fixes: c3e2485d5f ("dt-bindings: usb: Convert the generic EHCI binding to YAML")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-2-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
